construction Development of Sophisticated wormens park at sirnoo pulwama

Gazeebo

Earth work in excavation by manual means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages loading un-loading and stacking etc complete

: Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:4:8 coarse sand 40mm nominal size crushed stone agg.)

Providing and laying in postion spacified grade of reinforced cement concrete excluding the cost of centering, shuttering,finishing and reinforcement All work upto plinth level 1:1.5:3 (1cement:1.5 coarse sand: 3 graded stone aggregate 20mm nominal size)(Crushed).

Reinforcement for RCC work incld straightning, cutting, bending, placing in position & binding all complete (TMT bars of grade Fe-500D or more.)

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:2:4 coarse sand 20mm nominal size crushed stone agg.)

Centring and shuttering incld. Strutting, proping etc & removal of form work for Founadtions, footings, bases of columns for mass concrete

Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing..(Fine chisel dressed)

Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete First class Budloo/Fir wood

Providing /Fixing of high rib profile colour coated sheet roofing fixed with 75 mm long 6mm dia secrews upto( a pitch of 60 degree) excld cost of perlins, rafters & tresses 0.50mm thick with zinc coating not less than 275g/sqm i/c all carriages complete.

Providing ridges of hips of width not less than 0.45 overall width plain GI Green sheets fixed with polymer coated J or L hooks bolts & nuts 8mm dia GI limpet & bitumen washers complete 0.50 mm thick with zinc coating not less than 275g/sqm

Providing and fixing plained eaves boarding. 2nd class Deodar wood 250x32 mm (nominal size)

Providing wood work in frames of false ceiling, partitions etc sawn & put up in position Budloo/Fir wood

Providing and fixing 12mm thick plywood for ceiling of approved brand and manufacture (frame work for base to be paid for separately) with M.S. screws i/c all carriages complete.

Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of frame work which is to be paid separately. Chaar Gul i/c touch wood polish complete with Polishing on wood work with ready mixed wax polish of approved brand and manufacture on New work All inclusive

Providing and fixing of ornamental type vertical posts of first class Kashmiri deodar wood of approved pattern and design including providing and applying two or more coats of touch wood polishing etc. complete in all respects.(size 6"x 6" dia. & 9'.0" height) including al carriages upto site of work complete in all respects.(Analysis enclosed)

Carriage of materails By Mech.Transport, from source to site of work

Stone agg.above 40mm for an avg lead of 10 km

Stone agg. Below 40mm for an avg lead of 10 km

Sand for an avg lead of 15 km

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: in all kinds of soils.

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages loading un-loading and stacking etc complete

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:4:8 coarse sand 40mm nominal size crushed stone agg.)

Providing and laying in postion spacified grade of reinforced cement concrete excluding the cost of centering, shuttering,finishing and reinforcement All work upto plinth level 1:1.5:3 (1cement:1.5 coarse sand: 3 graded stone aggregate 20mm nominal size)(Crushed).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, pivers, abutments, posts and sturts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size)(Crushed). .

Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V level

Providing and laying in position cement concrete of specified grade excl. the cost of centering and shutering. All work upto plinth level 1:2:4 (1cement: 2 fine sand: 4 graded stone aggregate 20mm nominal size)(Crushed).

Reinforcement for RCC work incld straightning, cutting, bending, placing in position & binding all complete (TMT bars of grade Fe-500D or more.)

Centring and shuttering incld. Strutting, proping etc & removal of form work for Founadtions, footings, bases of columns for mass concrete

Centring and shuttering incld. Strutting, proping etc & removal of form work for colums, pillars, piers, abts, posts and strats

Centring and shuttering incld. Strutting, proping etc & removal of form work for suspended floors, roofs, landings, balconies & access plateform

Structural steel in double section fixed with connecting plate incld cutting hoisting fixing in positon and applying a priminng coat of approved steel primer all complete welded built up section

Brick work with FPS bricks of class designation 75 in foundtion & plinth in cement mortar 1:6 (1 cement, 6 coarse sand) i/c Extra for brick work with common burnt clay bricks in superstructure above plinth level upto floor five level

12mm Cement Plaster of mix 1:4(1 cement:4 coarse sand)

6 mm cement plaster to ceiling of mix 1:3(1 cement: 3 fine sand)

Distempring with oil bound washable distemper of approved brand & manufacture to give an even shade New work (2 or more coats)over and incld. Priming coat with cement primer

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10sqm)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.149A.1Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm &sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and Drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixingand erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work i/c primer

Carriage of materails By Mech.Transport, from source to site of work

Stone agg. Above 40mm for an avg lead of 10 km

Stone agg. Below 40mm for an avg lead of 10 km

Sand for an avg lead of 15 km

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, leadup to 50 meterand lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil :

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages loading un-loading and stacking etc complete

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:4:8 coarse sand 40mm nominal size crushed stone agg.)

Providing and laying in position cement concrete of specified grade excl. the cost of centering and shutering. All work upto plinth level 1:2:4 (1cement: 2 fine sand: 4 graded stone aggregate 20mm nominal size)(Crushed).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colou r& pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 16.93.1 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern

Centring and shuttering incld. Strutting, proping etc & removal of form work for Founadtions, footings, bases of columns for mass concrete

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment) i/c laying and consolidation by PRR 8 to 10 ton capacity complete job.incld all carriages complete.

Preparation of mounds of various size and shape by available excavated/supplied earth in layers not exceeding20 cm in depth, breaking clods, watering of each layer dressing etc. lead upto 50 meter and lift upto 1.5 m complete as per direction of officer- in -charge

Carriage of materails By Mech.Transport, from source to site of work

Stone agg. Above 40mm for an avg lead of 10 km

Stone agg. Below 40mm for an avg lead of 10 km

Sand from for an avg lead of 15 km

Seating

P/F of ornamental cast iron benches 3 seater of approved make and design with MS tubular seating Arm rests ,with back rest including fixing of benches in ground that is earthwork and fixing in cement concrete of 1:2:4 mix complete job all as per directions of EIC.

Fountain

Earth work in excavation by manaul means in trenches for foundations drains , pipes , cables etc. (not exceeding 1.5 m in width ) and for shafts , wells , cesspits and the like not exceeding 10 sqm on plan depth up to 1.5 m including disposal of excavated earth up to 1 m from cutting edge disposal earth is to be leveled and neatly dressed( in all kinds of soil)

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages & Head Loads loading un-loading and stacking etc complete

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:3:6(1 cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level ):1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete :Thermo-Mechanically Treated bars of grade Fe-500D or more i/c all carriages

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Providing and laying machine cut, mirror polished, Italian Marble stoneflooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. : 18 mm thick Italian Marble stone slab, Perlato, Rossoverona, Fire Red or Dark Emperadore etc.(cost to be inclusive of chemical treatment of approved AQUA SEALANT on surface etc complete as per directed)

Providing and fixing chaina mosiac on 100 mm thick CM -1:4 laid in proper slope and gradient with screened and washed sand for mortar with necessary grout in required quantities making necessary vatts on wall ,acid wash etc complete.

Providing and laying in position cement concrete of specified grade excl. the cost of centering and shutering. All work upto plinth level 1:2:4 (1cement: 2 fine sand: 4 graded stone aggregate 20mm nominal size)(Crushed).

Carriage of materails By Mech.Transport, from source to site of work

stone aggregate /sand for an avg. lead of 5 km

Feeder room

Earth work in excavation by mechanical means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed by EIC. All Kinds of soil

Providing and laying of hand packed stone boulder (size 150mm-230mm) before laying of PCC compacted consolidated rammed filling the voids compacting all complete carriage upto site of work all head loads complete job.

Providing and laying in position cement concrete in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including curing but excluding the cost of centring and shuttering.

Providing and laying in cement concrete in 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)including curing but excluding the cost of centring and shuttering.

Centering and shuttering including strutting, propping etc. and removal of form work complete job.

Foundations, footings, bases for columns

Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs andsteps etc.

Suspended floors, roofs, landings, balconies and access platforms.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 12:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)complete job

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies,etc upto five level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) complete.

Brick work bricks of class designation 7.5 in superstructure above plinth level upto floor five level and curing complete inCement mortar 1:6(1cement : 6 coarse sand) complete job

Reinforcement for R.C.C work including straightening cutting, bending placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more..Including carriage of all materials involved with loading unloading and stacking complete.

15 mm thick cement sand plaster in 1:6 mix complete job

Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) overand including priming coat with water thinnable cement primer.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. Complete 50 mm thick with 20mm nominal size stone aggregate.

VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete size 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung UPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge. 200 x 19 x 1.9 mm

providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary screws etc. complete.

Providing and Fixing factory made UPVC door frame, made of UPVC extruded sections , of size 65 mm x 55 mm with wall thickness 2.0 mm ( ± 0.2 mm) , corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fasteners, all complete as per manufacturer’s specification and direction of Engineer-in-charge.

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Filling the gap in between aluminum frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm width

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length Second class kail wood

P/f of single or double glass paness in upvc windows 5mm thick complete job

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Second kail wood 30 mm thick

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick Second Class kail wood

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications:

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 250x10 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete : 125 mm

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Providing Colour coated High rib sheet roofing including vertical/curved surfacfixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled withwhite lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch inhorizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing plained eaves boarding.2nd class kail wood 250x32 mm (nominal size )

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in charge. External work including trenching, refilling etc.25mm nominal outer dia pipes.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in charge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.20mm nominal outer dia pipes.

P/F of following PVC pipes and fittings of standard quality and make (B Type) incl. jointing /testing complete

100 mm dia PVC Pipes

75 mm dia PVC Pipes

Plain bend

P trap(100 mm)

Reducer

100 mm x75 mm

Floor Trap (100 mm)

Floor Trap (75 mm)

Collar 100mm with rubber washer

Collar 75 mm with rubber washer

Providing and fixing water storage tanks with PVC lid having locking arrangement (triple layer of approved quality sintex or equivalent) incl making inlet outlet and overflow connections and carriages complete

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm bore

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) 25 mm dia. nominal bore

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets incld 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fitting setc complete job approved by engineer incharge

P/F CP brass fittings of standard quality and make as per directions of EIC.

Bib Cock

Angle valve

Wall mixer

Health Faucet

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, 78 mmwide and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

P/F of approved quality and make geysers( incl all necessary fittings nuts, bolts,pvc connections etc.complete all as per directions of EIC.

Carriage of materails By Mech.Transport, from source to site of work

Stone agg. Above 40mm for an avg lead of 10 km

Stone agg. Below 40mm /sand for an avg lead of 10 km

Bricks for an avg lead of 15 km

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe40 mm dia

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. Of quality and make as approved by Engineer - in - charge.

P/F of sbd stainless steel anti cock roach with hole floor drain strainer

P/F of rcc rings 1.2 m dia (1:1.5:3) mix of concrete 150 mm height 100 mm thick i/c excavation complete joball as per directions of Engineer - in - charge.

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) cover with frame (heavy duty) FRP 450x450 mm internal dimensions, R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 (1 cement: 4 fine sand: 8 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions450 x450 mm and 45 cm deep for single

P/F of heavy duty manhole FPR cover 1.5'x1.5' COMPLETE JOB

Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 liter capacity -White

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1MMTHICK

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade 16 mm thick

Extra for providing opening of required size and shape for wash basin/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite / stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510mm bowl depth 200mm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work

Walling

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m inwidth) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: in all kinds of soils

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages loading un-loading and stacking etc complete

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:4:8 coarse sand 40mm nominal size crushed stone agg.)

P/L in position specified grade of reinforced cement cencrete excld. The cost of centring, shuttering, finishing and reinforecement-All work upto plinth level. 1:1.5:3 graded stone agg. 20mm nominal size

Providing and laying in position cement concrete of specified grade excl. the cost of centering and shutering. All work upto plinth level 1:2:4 (1cement: 2 fine sand: 4 graded stone aggregate 20mm nominal size)(Crushed).

Centring and shuttering incld. Strutting, proping etc & removal of form work for Founadtions, footings, bases of columns for mass concrete

Centring and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached plasters, buttresses, plinth and string courses etc.

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Reinforcement for R.C.C work including straightening cutting, bending placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more..Including carriage of all materials involved with loading unloading and stacking complete.

Carriage of materails By Mech.Transport, from source to site of work

Stone agg. Above 40mm for an avg lead of 10 km

Stone agg. Below 40mm for an avg lead of 10 km

sand for an avg lead of 15 km

Illumination facility by way of Ornamental poles to women's Park at Sirnoo Pulwama.

Supply installation testing and comm. of 7 Mt. octagonal M.S pole designed as per ILE TR7 and BS5649 for structrual design & as per IS 875 ( part III) 1987 for dynamic loading. M.S sheet thickness: 3mm Galvanization thickness 65 microns ( min) Door size:250mmx65mm, along with 4 No. foundation bolts Utkarash/ bajaj/crompton/ valmount make.

Providing of cement concrete block with dimensions( 2'x2'x4.5') including grouting 4 no foundation bolts, cement concrete to be carried in 1:2:4 mix.( RCC) including cost of M.S reinforcement ( as per approved drawing ) and cost of shuttering.

Earthing of the pole, Complete by GI Pipe 40 mm dia. 0.5 mtr long through 10 swg GI wire after driving in ground up to a depth of 3' from the base of foundation including nuts , bolts etc. (Complete job)

Supply and fixing of four way arm bracket( square type 2'x2') for mounting the luminaire on the top of the pole fabricated out of 48.3 mm OD GI pipe , welded and supported with a triangular MS gasset plate , with a provision of cast iron cap.( design to be approved before installation)

Supply, installation , testing and commissioning of LED based Flood light, housing made up of pressure die cast aluminum Alloy with effective thermal management,sturdiness and embossed brand name/logo name of manufacturer. The fixture should have a minimum system efficacy of greater than 120 lumen/Watt and a minimum system lumen output of 18000 lumens and maximum system wattage of 150 Watts.The fixture shall have a CRI of minimum 70, SDCM<5. The fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection of IP66 (lamp and gear Compartment) and Mechanical Impact Resistance Rating of IK >=07 with toughened glass cover.The fixture driver should have an operating voltage range of 140-270 V, inner surge protection of >=4KV, PF >0.95 and THD<10% at full load. Driver should cut off at high voltage of 320volt for safety. The fixture should comply with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics. Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Philips/ LT/ Wipro/Havell make ( sample to be approved before installation)

Supply installation testing and commissioning of Heritage architectural ornamental decorative cast iron pole as per specification/ drawing (enclosed) Dwarka make /Karara Mujasame or of Equivalent standard Make with the following specifications:- The pole shall look like as shown in the drawing. It shall have all similar features as shown in the enclosed drawing/picture. The Cast Iron Pole of 3 Mtr (3000mm) length. The pole has ornamental base (Approx. overall dimension-height 1050mm,bottom dia 370mm) shall have a provision of inbuilt junction box for fixing MCB’s or cutouts with detachable window cover. The part above ornamental base design consists of decorative sections of circular shapes & collar in different dimension, is made of cast iron in fine finish. The design of the cast-iron parts is clearly shown in the drawing. Mentioned dimensions are proposed dimensions, which may vary with actual measurements (Tolerance of ±5%) Further the pole shall be got approved by the concerned engineering wing after providing a sample before execution of work and the test certificate to be provided by the manufacturer. the job also includes Spiral Earthing through 10 swg GI wire after driving in ground up to a depth of 3' in the ground from the base of the pole.

Supply and fixing of ornamental Cast iron 2 way bracket painted with anti-corrisive enemal paint as per design , of Dwarka india /Karara Mujasseme of equivalent make/design ( as per enclosed drawing) The bracket should have a provision of fixing luminaries of Glowmac/Green arrow. Further the bracket shall be got approved by the concerned engineering wing after providing a sample before execution of work and the test certificate to be provided by the manufacturer.

Providing of Reinforced cement concrete foundation as per specifications/enclosed drawing including foundation nuts & bolts( to be paid seperately) of required size welded together firmly with reinforcement properly, cement concrete to be carried in 1:2:4 mix.

Supply fixing testing and comm.of decorative ornamental translucent luminarie having IP-65 protection ( glowmac ( Amphore-PRISMATIC-A-300PC-201 ) / bajaj/havell equivalent make)

S/F/T/C of 18-22 Watt LED Philips/ Havell /Crompton greaves make.

S/L , testing and commissioning of PVC alluminium armoured cable 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Havell/Eq. standard make as directed by engineer incharge and making end termination with brass compression gland and aluminium lugs of required size.

a) 25 sq.mm 4 core

a) 10 sq.mm 4 core

Providing of service connection and earthings to luminaire from the junction box in 1.5 mm PVC insulated, multicolour copper wire .

Supply and errection of Cast iron ornamental lamp post 90 cm. ( bollard type) ( As per Approved sample/ drawing enclosed) having provision at bottom for built in gear box fitted with PVC 4 way connector 63 amp and 1-6amp MCB and clear painting coat. Dewarka (DBL-103, 90 CM) /Karrarie-Mujasame or equivalent standard make as directed by engineer incharge. the job also includes LED Lamp 20-25 Watt to be installed in the bollard with suitable no. of dash fasteners to be grouted in the cement concrete for holding the bollard.Mentioned dimensions are proposed dimensions, which may vary with actual measurements (Tolerance of ±5%) Further the pole shall be got approved by the concerned engineering wing after providing a sample before execution of work and the test certificate to be provided by the manufacturer. the job also includes Spiral Earthing through 10 swg GI wire after driving in ground up to a depth of 3' in the ground from the base of the pole.

Providing of Reinforced cement concrete foundation as per specifications/enclosed drawing including foundation nuts & bolts of required size welded together firmly with reinforcement properly, cement concrete to be carried in 1:2:4 mix.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,jointing etc.direct in ground (50-60 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

Supply and installation of Earthing through 10 swg GI wire after driving in ground up to a depth of 3' in the ground from the base of the pole, with g.i rod to be embedded in the pit.

S/L , testing and commissioning of LT Power Cable , copper conductor ,XLPE Insulated,unarmoured cable 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Copper cable Havell/Eq. standard make as desired by the engineer incharge and making end termination with brass compression gland and copper lugs of required size.

b) 6 sq.mm 4 core(un-armoured)

Supply installation testing and comm. Of 2'x1'6"x9" control pannel outdoor type sheet steel 16SWG powder coated phosphatised having angle iron stand fitted with following accessories to be grouted in the cement concrete, complete job .the panel to be fabricated from reputed firm duly approved by CPRI.as per approved design, size may vary as per site requirement)

a) 100 amp 4 strip bus 1 No.

b) A/V meters set/indicators

c) Switch/ Socket 16 amp -2 No.

c)MCB TPN 40-63 amp 3 NO.

Design, Fabrication, Supplying, Installation, Testing and Commissioning of following panel made out of 2mm thick M.S. sheet, floor/wall mounted, vermin and dust proof, outdoor type with suitable size of angle iron legs grouted in the cement concrete., with lockable type hinged doors, duly painted with provision for fixing of incomer MCCB, outgoing DP MCBS, sets of Aluminium Bus Bar of different rating. after taking Derating factor into account, and other allied accessories etc. as required. the panel to be fabricated from reputed firm duly approved by CPRI.as per approved design, size may vary as per site requirement) 2 N0.

Providing and fixing of following protection equipments and other allied accessories including connections, inter connections, with suitable size of PVC insulated copper conductor cable including earthing etc. as required.

INCOMING:

a)160A 4P MCCB 35 KA Legrand/ Shinider/ Eq. standard make.

b) 4 No. of Aluminium Bus Bar of 250 Amp.

c)Digital meters and phase indicators -1 set.

d) Astronomical timer with 4 pole contactor of suitable capicity. Legrand/ L&T /Schineider make

OUTGOING:

a) 63 amp TPN MCB

b)space for 8 way MCB'S

Providing of earthing by way of digging 10' deep pit then embedding 2'x2', 5mm thick copper plate connecting the plate with main control board by 10 SWG copper wire with 1/2" dia. Full thread brass nut and bolt and washers. Refilling of pit with alternate layers of salt coal and earth.

S/I testing and comm. Of three phase 20 KVA 50HZ oil cooled(Transformer oil is to be provided with stabilizer conforming to IS 335,IEC296)) unbalanced type servo voltage stabilizer(A.E / Cosco/ Electricfield make) having an input voltage ranging from 156V to 415 V ( phase to phase) and balanced output voltage of 415V, +/- 1%. ( Test certificate to be provided by the manufacturer) The unit incorporate

b) A three phase change over switch to read voltage on incoming and output side

c) indicating lights 6 No two numbers for each of the motorised units, one for lower limit and other for higher limit.

e) Single phase Preventer ( contactor Switch of required rating) Legrand make.

f) six potential meter resistance with lock meter two for each phase control, one for sensitivity and other for level control.

g) two sets of indication lamps three numbers each to indicate output and input indication

h) 20 % over load bearing capacity for one hour.

Provision for creation of 63KVA substation, HT Network and allied works

Supply installation testing and commissioning of 11/0.433kV, 63 KVA, 3-phase Distribution Transformer ( Alba/North sun/ Zain/ Eq. standard make) with Bimetallic Terminal Connectors Energy Level-2, (Al. wound ) , and with LV Cable Box having detachable Al. Gland plate with LV Bimetallic terminal connection suitable for vertical take off of cable. 11 kV Gapless Surge Arrestor,9 kV ,10 kA ,LA with polymer housing, Stn. Type. 11kV GO, AB Switch 3-Phase, 3-Pole, 200 Amp, Vertical Type , 11 kV Horn Gap Fuse Set 3 Phase 200A.70mm² (1Ckt for 63 kVA),single core Cable,1.1kV Grade, XLPE Insulated Stranded Conductor FRLS type (44mtr for 1 Ckt), 9 Mtr. Long Pole,(ST-410 SP33), 11kV Polymeric composite Disc Insulator 12kV,min failing load 45kN, Lighting Impulse 75kV Positive and 80kV Negative, creepage distance 320mm with fitting,GI Channel/Angle/Flat of sizes including clamps, Galvinized Nuts and Bolts. Earthing of substation as per IS standards, 11kV Polymeric composite Pin Insulator 12kV, 5kN, Lighting Impulse 75kV Positive and 80kV Negative, creepage distance 320mm ,LT Distribution Box for:- i) 63 kVA DTR with 100 Amp MCCB 3P 16 kA for incomer & 100 Amp MCCB 3P 16 kA 1 No. and 63 Amp MCCB 3P 16 kA 1 No.s for Outgoing Circuits. 3-Ø, 4-Wire Trivector Meter (Prodigy ) with suitable ring type CT 200 Amp. Cement bottoming 1:2:4 mix as per Standards 0.48 cum/pole, Painting of Poles Red Oxide, Aluminium paint. ( complete Job)

internal Electrification facility to Feeder Room/ Toilet Block at Sirnoo Park Pulwama.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 2X 1.5 sq.mm FRLS PVC insulated copper conductor ( Havell/Polycab/ Fenolex/ Anchor/eq. standard make as desired by engineer incharge ) single core cable in surface / recessed medium class PVC conduit, with modular switch ( Legrand Mylinc /SSK NV/schneider Livia /ABB Tvisha make.), modular plate,suitable GI box, deep junction etc.

Wiring for light/ power plug with 2X4 sq. mm + 1X 4 sq. mm earth wire , FRLS PVC insulated copper conductor ( Havell/Polycab/ Fenolex/Anchor/ equivalent as directed by engineer incharge.) single core cable in surface/recessed medium class PVC conduit.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,modular plate, suitable GI box , connections etc. as required. Modular Switch & Socket:- ( Anchor roma plus/Legrand Mylinc /SSK NV/schneider Leiva /ABB Tvisha make make.)

Wiring for lighting circuits/ inverter circuits/ 6- 10 amp power plugwith 2X2.5 sq. mm FRLS PVC insulated copper conductor ( Havell/Polycab/ Fenolex/Anchor/ equivalent as directed by engineer incharge.) single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 2.5 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). Modular Switch & Socket:- ( Anchor roma plus/Legrand Mylinc /SSK NV/schneider Livia /ABB Tvisha make.)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supply installation testing and commissioning of Indicator of Anchor roma plus/Legrand Mylinc /SSK NV/schneider Livia /Crabtree athena make.)

Sub Head-2 - Fixtures and Fittings

Supply installation testing and commissioning of 18 W + LED Surface/recess, square or round Mounted light luminary fitting shape with minimum system lumen efficacy of 100 lm/W with Pressure Die cast Aluminium Heat Sink and P.F.>0.95 ,THD<10% ,CCT 5700K, CRI 80.The LED with Useful life of 50000 Hrs at L70, seperate driver, heat sink, earthing provision.. The Input voltage range shall be 150V to 270V .The Fixture should have In-built Surge Protection of 2kV. Certification:- LM79 & LM80 test report should be from govt approved In-house NABL lab/ government of India. The job includes AMC (reckoned from date of successful commissioning) of lighting fixtures for a period of Two years ,which includes replacement of fixtures of Philips/ Trulux/Wipro make / sample to be approved before installation..

Supply, Installation, Testing and Commissioning of 1200 mm sweep, ceiling fan with 3 No. Aluminium blades, 30 cm long down rod, 2nos. canopies, shackle kit, Power Factor not less than 0.9, Service Value including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, and including Fan Junction complete . USHA /Havells /Crompton make, sample to be approved before installation..

Supply and fixing of 6 amp/250 V A.C fan dimmer step type 2 module with cover plate Anchor roma plus/Legrand Mylinc /ABB Tivsha/schneider Livia /Havell Coral make.

S/F testing and comm. Of MCB's 10 K of the below mentioned capacities in sub main controls ABB SB200/Legrand Dx3/Seimens Betaguard/ Schneider Acti_9/equivalent make as directed by engineer incharge.

a) 6-32 Amp SP MCB

b) 40-63amp DP MCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board,( Havell/ legrand/ Shinider/SSK make) 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, interconnections, powder painted including earthing etc.as required. (But without MCB/RCCB/Isolator)

14 way, Double door

Supply fixing testing and comm. Of backlite holder /batten holder/angle holder/ceiling rose SSK/Anchor make incl. PVC Block.

S/L , testing and commissioning of, XLPE Insulated, PVC alluminium cable ( unarmoured) 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Havell/Eq. standard make as directed by engineer incharge and making end termination with brass compression gland and aluminium lugs of required size.

a) 16 sq.mm 2 core

Design, Supply,Installation,Testing and Commissioning of 01 No. Fountain For Women Park Sirnoo Pulwama

Design,Supply,installation,testing and commisioning of 5mtrs Dia Circular Ring(Jet Nozzle Header) made in GI pipe(B-Class,dia-80mm) fitted with not less than 64 No. sockets placed symmetrically at a distance of aprox. 9 inch gap all along the circumference of the header line and 06-No 40mm inlet sockets. The Job Includes fixing of all GI fittings, Hinges,Supports, Clamps etc. necessary for completion to the satisfaction of the Engineer in Charge

Design,Supply,installation,testing and commisioning of 3mtrs Dia Circular Ring(Jet Nozzle Header) made in GI pipe(B-Class,dia-80mm) fitted with not less than 43 No. sockets placed symmetrically at a distance of aprox. 9 inch gap all along the circumference of the header line and 06-No 40mm inlet sockets. The Job Includes fixing of all GI fittings, Hinges,Supports, Clamps etc. necessary for completion to the satisfaction of the Engineer in Charge

Design ,Supplying, Installation, Testing and Commissioning of Single Jet Nozzles (crown type) Complete with ball joint for 15 Degree pivoting made of brass with Nickle plating, flow straightner in following size . Height of water stream upto 10 mtrs. etc. complete as required.

Design, Supplying, Installation, Testing and Commissioning of Eco Cluster Nozzle made of stainless steel with inlet dia 40 mm and 21 nos Single jets to create 38 mm dia full jet for height 10 mtr water level in depended etc. complete as required.

Design Supply, Installation, Testing and Commissioning of ISI Marked openwell submersible pump set contain with stainless steel shaft and cast iron/SS body, the pump shall be designed to prevent over loading and having dynamically balanced rotating parts etc. the pump capable of delivering following capacities discharge at suitable head and lowering the pumps in water bodies and suitable for operation on 415V(+- 10%), 3-phase AC supply including providing required no's of heavy duty M.S clamps made of flat iron and suitable size top cover made of suitable thick MS sheet including connection, interconnection ,supports etc. as required. suitable for 900LPM at 25 Mtrs Head etc. complete as required.

Design Supply/Laying/Testing/Commissioning of 3.5 core 35 sq mm Al conductor PVC insulated armoured cable. (to be paid as per actual)

Design ,Supply/ Laying/Testing/Commissionin of Cable 3 core 10 sq mm copper conductor flat/submersible type PVC insulated.(to be paid as per actual)

Supply /laying of 25 sqmm PVC conduit along with necessary accessories and fittings (to be paid as per actual)

Plumbing ( Piping) Work : Design/ Supplying/ Fixing/ Testing/ and Commissioning of GI B-Class Pipe Header/Network in pipe sizes 80mm, 50mm and 40mm of reputed make confirming to ISO 15874 or equivalent including welding,fitting like elbows,tees,flanges,hinges,supports,taper etc All fixing to be done to the entire satisfaction and as approved by Engineer-In-charge.

Providing and fitting of 40mm Ball valve(Brass, heavy) .

Providing and fitting of 15mm Ball valve(Brass, heavy) .

Design Supply, Installation, Testing and Commissioning of Suction Screen stainer made of ABS to be fitted in suction to protect the pump from enrty of external materials etc. complete as required.

Design, Supply, Installation, Testing and Commissioning of water proof (IP 68) power supply unit of not less than 200W i/c connection along with 2 years free replacement guaranty etc. complete as required.

Design ,Supply, Installation, Testing and Commissioning of RGB controller with remote Kit wattage not less than 200 watt i/c connection along with 2 years free replacement guaranty etc. complete as required.

Design ,Supply,Installation, Testing and Commissioning of Signal Amplifier of RGB signal as require i/c connection along with 2 years free replacement guaranty etc. complete as required.

Design ,Supply,Installation, Testing and Commissioning of Power Supply/SMPS for suitable to run LED Lights, Body-Metal input Power-220 V AC/ Output Power-12 V DC etc. complete as required.

Design ,Supply, Installation, Testing and Commissioning of underwater Luminaries surface mounted RGB LED spot light 3 x 3W with IP 68 protection, SS/ aluminum dia casting body with power coated paint, soft rubber

SITC of 100 A Three Phase Control Panel including 100 A 4Pole MCCB, C/O Switch, Bus Bar copper, Voltmeters, Ammeters, Switch-gear. The panel shall be fabricated sheet metal 14 guage with powder coated out door type with rating IP67. The Outhgoing shall have 1. Two Outgoing Feeder for 7.5 Hp Pump compatible with VFD starter. 2.Feeder suitable for Fountain Lighting. 3.Auxillary Feeder (Blank)

Design, supply, installation, testing, and commissioning of a fully integrated control panel for operating two submersible pumps using VFD starters, along with a dedicated feeder for fountain lighting and auxiliary blank feeder. Each pump feeder shall include its own VFD with associated contactors, overload relays, and single-phase preventers to ensure smooth soft start/stop, variable speed control, and protection against dry-run and phase failure. The lighting feeder shall incorporate a suitable power supply and control module for low-voltage LED operation. Auxiliary control relays shall be provided for sequencing, auto/manual logic. The panel shall support both manual and automatic operation modes through push buttons, timers, or sensors, and include necessary control wiring, isolators, MCBs, and neutral links. Proper earthing shall be provided for all electrical components and metallic parts.(The panel shall be fabricated out of CRCA SWG16 MS sheet with a powder-coated finish)

Design ,Supply, installation, testing & commissioning of 30 KVA Servo- stabilizer including all allied electrical accessories including trransformer oil(Not less than 200LTR) and weather proof CRCA enclosure . The stabilizer should have following specifications:main supply a) Capacity: 30 KVA, 3-phase unbalanced type b) Input: (110-260) V AC P-N; (190 - 450) V AC P-P c) Output: 415 V ± 1% - phase to phase d) Supply: 3 phase, 4 wires, 50Hz e) Operation: Automatic f) Duty cycle: Continuous g) Transformer windings: Copper wound on CRGO laminations as per IS specifications h) Cooling: Oil cooled i) Efficiency: Better than 98% at full load j) Overload capacity: 15% for continuous 4 hours k) Waveform distortions: Nil l) High speed voltage correction: up to 8V to 20V per second m) Protections: Under voltage, Over voltage and Overload with time delay n) Other features: LED indicators, Digital AC ammeter, AC voltmeter, Frequency meters, Phase Sequence meters, Single phase preventer, and Stabilizer by-pass arrangement. The Job also includes P/F of 63 Amp 4 Pole MCCB as incomer to the Servo Stabilizer to be provided in CRC Enclosure.

Supply, installation, testing, and commissioning of a single-phase monoblock pump (capacity: 0.5 HP to 1 HP) for transferring water from the source to the fountain. The pump shall be securely mounted on a concrete foundation and housed within a weatherproof (rainproof) enclosure (if required). The scope includes: - Electrical wiring and connections from the power source to the pump - Provision and installation of appropriate-rated MCB for pump protection - All necessary accessories and fittings for complete function.

Supplying/ Fixing/ Testing/ and Commissioning of 'B class Medium duty GI pipe conforming to IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:. - Suction Line: From source to the pump suction inlet. - Delivery Line: From the pump discharge outlet to the fountain.

50mm(to be paid as per actual)

40mm(to be paid as per actual)

The Comprehensive Annual Maintenance Contract (CAMC) for the fountain following the completion of a one-year Defect Liability Period (DLP), shall be valid for one year and include routine, preventive, and breakdown maintenance covering all aspects of the system, including timely repair or replacement of worn-out or defective components with minimal downtime. All repaired or replaced items during the CAMC period shall carry appropriate warranty and guarantee as per contract terms.

Please Enable Macros to View BoQ information