GE/BAS-53/2023-24 Provn of visitor room toilet block and special repair to LT cable bus bar LT panel at Madhopur under GE Basoli

Amount

Excavation in trenches in any type of soil n.exc 1.50m wide and n. exc 1.50m in depth for foundation of pole/stay and laying of UG Cable and other and getting out complete all as specified and directed.

Surface excavation in any type of soil n. exc.30cm deep and averaging 15cm deep and getting out complete all as specified and directed.

Removal of excavated (soil) material to a distance not exceeding 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spereading, leveling, watering and well ramming in layers not exc 25cm thick each complete all as specified and directed

M&L Cement Concrete in foundation filling and mass concrete of mix 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:4 including flush pointing with same mortar as the work proceed complete all as specified and directed.

M&L brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces with 1:6 CM on internal faces of wall, finishing the surfaces even & smooth w/o using extra cement complete all as specified and directed.

M&L Rendering 15mm thick on brick or concrete surface in CM 1:4, finished even and smooth with out using extra cement complete all as specified and directed

M&L Rendering 10mm thick on fair faces of concrete surfaces with CM 1:3 on ceiling surfaces etc., finishing the surfaces even & smooth w/o using extra cement complete all as specified and directed.

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases of columns etc basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in slabs, supported on walls, beam and columns in floors, and in shelves and the like complete all as specified and directed.

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in columns, pillars ,piers,posts and struts complete all as specified and directed

M&L Reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregates as in beams ,chajja,cantilevers, bressummers, lintels over 1.5 mtr span complete all as specified and directed

Steel Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and sofits of foundation and plinth beams; and similar works; vertical or to batter for rough finished flat surfaces complete all as specified and directed

Steel Form work to sides and soffits of floor/roof beam for rough finished flat surfaces of concrete complete all as specified and directed

Steel Form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and directed

Steel Form work to soffits of suspended slabs such as roof slabs, floor slabs etc not exceeding 200mm thick complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

-ditto- here-in-before but 8mm dia and over upto and including 10mm dia as in stirrups, spacers, binders complete all as specified and directed.

M&L 100 mm thick Cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed

M&L Non-skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but n . Exc 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 15 mm thick screed bed in CM 1:4. all complete all as specified and directed.

M&L Non-skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but n . Exc 0.38 sqm ,in skirting/dado/risers of steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 10 mm thick rendering in CM 1:4. all complete all as specified and directed.

M&L Non-skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile n. Exc 0.18 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 15 mm thick screed bed in CM 1:4. all complete all as specified and directed

M&L Glazed ceramic coloured tiles of size 450x300X7mm/450x350x7mm thick in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade with 10 mm thick cement plaster in CM 1:4 .complete all as specified and directed

M&L Box type steel windows and ventilator comprised of tubular frame and shutters made out of 1.25mm thick MS Sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 150mm long for each leaf and 10mm square bar grills at spacing shown on drg welded to GI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. (i) Cutting holes for hold fast makig good incement mortar 1:3 and PCC 1:2;4 , type B-1 shall be included in the quoted rates complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F Frosted Sheet glass 3.00 mm thick glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S&F Galvanised MS wire cloth 0.46mm nominal dia of wire and average width of aperature 1.18mm, complete all as specified and directed

S&F solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, in opening etc complete all as specified and directed.

S&F factory made single piece solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat mounded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges with SS screws complete all as specified and directed.

S&F AluminIum anodised barrel tower bolt of size 150mm extruded section complete all as specified and directed.

S&F Extruded aluminum alloy handles of size 150mm fabricated type anodized complete all as specified and directed.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed .

S&F PTMT grating dome 100mm dia (minimum weight 25 gms) complete all as specified and as directed..

S&F Curtain rod 20mm dia of Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed .

S&F Pressed steel frame for doors with one or more rebates including necessary fixing lugs ,hinges, lock strike plate size of frame 125X60mm complete all as specified and directed.

PCC 1:3:6 type C-0 using 12.50 mm graded crushed stone aggregate as in back filling of pressed steel door frames and hold fast. complete all as specified and directed

S&F 35 mm thick Factory made 2nd class Hard wood shutter with top panel Glazed and skeleton open rebated and prepared to receive glass, gauze, etc.(without sash bars) fitted with cut and mitred beds for securing glass, etc.; and bottom panel with panel of 9mm BWP commercial ply or 12 mm veneered particle board with comercial veneering on both faces. The sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and directed ..

M&L for factory made, 2nd class Hard wood rail and style 35 mm thick, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for Earth filling, Spreading and levelling in layers n exc. 25 cm thick each and watering and well ramming under floor complete all as specified and directed

M&L Hardcore of broken stone or boulders of gauge n. exc. 63mm , deposited spread and levelled in layers n. exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in plinth ,sub floor,sub base etc.laid in alternate bays finished even and fair w/o using extra cement complete all as specified and directed.

M&L Preparation of new steel surfaces of any description exc 10 cm width or girth and apply two coats of synthetic paint over a coat of red oxide primer complete all as specified and directed.

M&L Preparation of new plastered surfaces and applying two coats of distemper oil emulsion on plastered surfaces over and including 3mm thick wall care putty complete all as specified and directed.

M&L Preparation of new plastered surfaces and applying two coats of exterior acrylic emulsion paint on wall complete all as specified and as directed.

M&L Prepration of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preperation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for roof treatment with the following specification - Removing existing water proofing treatment and applying water proofing treatment on horizontal or vertical surfaces by applying oil bound bitumen primer @ 0.20 Kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3 Kg/sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm, The overlap shall be minimum 100mm on transverse direction and 75 mm on longitudinal direction and sealing overlap by torch application and bonded and applying a coat of blown grade hot bitumen 85/25 over and below the membrane @ 1.20 Kg/sqm in drying over the membrane finished with solar reflective bituminous aluminium paint/ primer @ 0.10 Kg/sqm over RCC roof slab/ parapet after cleaning the surfaces by removing dust, dirt etc. as per manufacturer’s instructions including 15mm thick screed in CM 1:4 and all as specified and as directed. NOTE :- The work shall be executed at site by the authorised applicator of APP and as approved by the GE.

M&L for Anti-termite treatment to backfilling in contact with foundation @ of 7.5 Ltr per sqm on vertical surface, complete all as specified and as directed.

M&L for Anti-termite treatment to the top surface of filled earth @ of 5 Ltr per sqm of surface, complete all as specified and as directed.

M&L for Anti-termite treatment to the under plinth @ of 5 Ltr per sqm of surface, complete all as specified and as directed.

S&F bib taps screwed down high pressure with both ends for iron pipe 15mm bore fancy type chromium plated complete all as specified and directed

S&F Steel water tubing 15 mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.), complete all as specified and as directed.

M&L cutting chases pinning in brick mas and making good to facing where required and pointing in cement and making good in CM 1:3 cutting n.exc. 10 cm in girth, complete all as specified and as directed.

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc complete all as specified and as directed.

S&F stop valve cast copper alloy ,chromium plated fancy type, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe complete all as specified and directed.

S&F stop valve cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe with long shank chromium plated concealed type complete all as specified and directed.

S & F wash down water closet (Pedestal pattern)white (EWC)with P or S trap including connection to drain or outgoing pipe and including with 10 ltr capacity PVC flushing cistern including bracket for flush tank, PVC connection 450mm long and 15mm dia to flushing cistern /sanitary fitting with PTMT nuts of length 450mm and necessary fitting inlet outlet pipe connections and plastic water closet seat cover,15mm dia health faucet,closed pattern with recessed bottom cover and mild steel chromium plated hinges etccomplete all as specified and directed .

S&F towel rail 600 mm long of PTMT shelves fixed with and including chromium plated brass screws and plastic cleats(min weight 190gm).complete all as specified and directed.

S&F vitreous china wash hand basin white Oval shape of Size 550 mm dia including supply of pedestal,bracket, cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified.

S&F chromium plated shower rose with or without swivel joints 125mm size incl fixing to steel pipe complete all as specified and directed.

S&F water closet (Squat pattern) without lime concrete bedding, vitreous china long pan orissa pattern 580x440mm, white with integral foot rests including flushing cistern, PVC connection & flush pipe.including connectoin to trap, and to flushing pipe, antisyphonage pipe, etc. complete all as specified and directed .

S & F fancy type chromium plated brass Soap dish, any type, fixed to plugs with chromium plated brass screws, complete all as specified and as directed.

M&L sand filling under foundation including watering and consolidation complete all as specified and directed

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints of 75 mm bore fixed on wall complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints of 110 mm bore fixed on wall complete all as specified and directed.

S&F PVC (SWR) bends of (any radius) with access door of 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends of (any radius) with access door of 110 mm bore complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor traps, plain with grating including jointing to waste pipe with solvent cement complete all as specified and directed.

S&F 110mm dia PVC (SWR) floor traps, plain with grating including jointing to waste pipe with solvent cement complete all as specified and directed.

S&F 125/110mm dia PVC (SWR) gully traps, including jointing to waste pipe with solvent cement complete all as specified and directed.

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed.

S&F 110mm PVC(SWR) vent cowl complete all as specified and directed.

S&F , Continous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap(when open) 30mm, complete all as specified and directed.

S&F electromagnetic catchers for cupboards , complete all as specified and directed.

Rotational moulded polyethylene water storage tank 3 layer white colour water tank , non- toxic effect, algea formation protection (made from Virgin grade of polyetylene material which is duly stablized with anti-oxidentPlastic) of capacity 1000 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer ,20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc complete all as specified and directed.

M&L concrete bed to drain pipes including benching under and haunching in cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate) for 150 mm dia pipe complete all as specified and directed. .

Material and labour for Reinforced concrete pipes 150 mm bore , class NP-3, laid and jointed complete with collars, jointed with cement mortar, laid in trenches and tested including fittings of same grade complete all as specified and directed.

S&F PVC board 18 to 20mm thick prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber/angle iron frame work etc, weight not less than 12 Kg/Sqm complete all as specified and directed.

S&F 40mm dia cup boards knobs fixed with nut ,screws and washers or brass polished etc. complete all as specified and directed..

S&F brass handles of 100mm size complete all as specified and directed.

Point wiring with 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable in and incl rigid PVC conduit concealed medium grade with pressed mild steel terminal boxes(sheet not less than 1.6 mm thick) duly painted with a coat of red oxide primer with suitable thickness plastic laminated sheet cover 3mm thick of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire(green colour) to common earth dolly complete all as specified and directed by Engr-in-charge.Note: a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be included in each point etc (b) On RCC roof ceiling PVC conduit shall be provided on surfaces for any necessary point with proper fixing clips and no extra cost shall be paid for the job etc complete all as per specified and directed.

All as per item No 87 but for one 3 pin 5 Amp socket outlet on independent board complete all as per specified and directed.

Point wiring with 2.5 sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with sunk cast iron/pressed steel terminal boxes(sheet not less than 1.6mm thick) of adequate size with suitable thickness plastic laminated sheet cover 3mm thick for one 3 pin socket outlet 15 Amp on independent board including continuous 2.5 sqmm FRLS,PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, complete all as per specified and directed.

Supplying & Fixing switch piano flush button single pole one way 5 amps 230 volts, complete all as per specified and directed.

S&F in replacement fan regulator switch type stepped complete all as per specified and directed.

Supplying & Fixing switch piano flush button single pole one way 15 amps 240 Volts, complete all as per specified and directed.

Supplying & Fixing socket outlet 6 amps 5 pin flush type, 240 volts, complete all as per specified and directed.

Supplying & Fixing socket out let, 5 pin, 15 amps multi purpose 2 in 1 flush type, 240 volts AC, complete all as per specified and directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings complete all as per specified and directed.

S&F ceiling rose surface bake lite two to three terminal isolated body fixed on PVC round block complete all as per specified and directed.

S&F LED recess mounting powder coated white CRCA full glow panel 45 watt 2x2 ft incorporated with all fixing arrangements complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as per specified and directed.

S&F Wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver, 20 Watt LED fitting with 100 lumen/watt 6000k, 230Volts, diffused optics etc complete with all accessories, connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, fixed on two PVC round block and testing complete all as per specified and directed.

S&F Wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver, 10 Watt LED fitting with 100 lumen/watt 6000k, 230Volts, diffused optics etc complete with all accessories, connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, fixed on two PVC round block and testing complete all as per specified and directed.

S&F in Replacement of existing sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 4.0 Sqmm drawing into and including PVC non metallic rigid conduit of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 4.0 Sqmm as a earth continuity conductor(green colour) in and including in non metallic rigid PVC conduit, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as per specified and directed. Note :- (i) Rates are deemed to be included chases of conduit and sinking for boxes cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 4.00 sqmm single core (FRLS) PVC insulated copper conductor cable one run of 4.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

S&F in replacement sheet metal powder enclosure powder coated versatile double door single pole and neutral (SPN) 415Volt, 50Hz AC supply for 04 way. fitted distribution board for MCB provisions for one no incoming MCB SPN and outgoing MCB SP AC 230 VOLTS 50 hzac SUPPLY HAVING PROTECTION ip-43,IK-09 with copper bus bar rated 200amps, neutral link , earth bar complete all as specified and directed.

S&F in replacement sheet metal powder enclosure powder coated versatile double door single pole and neutral (SPN) 415Volt, 50Hz AC supply for 08 way. fitted distribution board for MCB provisions for one no incoming MCB SPN and outgoing MCB SP AC 230 VOLTS 50 hzac SUPPLY HAVING PROTECTION ip-43,IK-09 with copper bus bar rated 200amps, neutral link , earth bar complete all as specified and directed.

S&F MCBs single pole and neutral (SPN)/isolator 40 Amps with 10 KA breaking capacity of 'C' series in distribution boards complete all as specified and directed.

S&F MCBs single pole 6-32 Amps with 10 KA breaking capacity of 'C' series in distribution boards complete all as specified and directed.

Supply and fix single pole and neutral enclosurewith a two pin andearth plugand socket with single pole, 230v MCB 20Amp complete all as specified and directed.

Supply and fixing ceiling fan with blade, down rod, electronic regulator and accessories, 230 Volt, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete all as specified and directed..

Supply and Fix steel body Exhaust Fan 230 volts 300 mm sweep 50 Hz, with louvers complete all as specified and directed

Supply ,fixing and testing water heater storage type with multifunctional safety valve,electric operated 230 V,single phase complete including one no of heating element,automatic thermal cut out,flusible plug,anti vacum ,built in presser release valve,thermostat,rust proof powder coated body,indicator lamps and all safety advices as per IS capacity 25 litres, 5 star rating including suitable and making good disturbed surface complete all as specified and directed

Supply and fix LED lamp 9 watt , complete all as specified and directed.

M&L earthing complete with galvanised steel earth plate eletrode 600mmx600mm and 6mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top edges, of the plate not less than 1.5m below normal ground level, connected to the galvanised iron earth lead 32mmx6mm (GI Strip) size, by means of nut, bolts, check nuts and washers of galvanised iron and 32mmx6 mm earth lead protected by provision of GI medium grade pipe 40 mm bore including provision of aggregates with 40 mm thick cover of RCC (1:2:4) , reinforced with XPM (weight not less than 4 kg per sqm) and frame of angle iron 40mmx40mmx3mm and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe of suitable length for watering perforated at bottom placed on top edge of earth plate, common salt and charcoal filling, funnel, wire mesh and earth work in any type of soil, returning filling in, removing soil to a distance not exceeding 50 mtr all as per plate No 3 of SSR 2009 Part-I and connecting to feeder pillers and Transformer all as specified including testing on completion complete all as specified and directed. (Note: The rate quoted include cost of min 7.5 metre earthing wire .)

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 of SSR Part-I (2009) including filling of charcoal dust , common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthing wire .)

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 2 core complete all as specified and directed..

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 4 core complete all as specified and directed.

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core complete all as specified and directed.

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 core complete all as specified and directed.

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 core complete all as specified and directed..

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 120 Sqmm 3.5 core complete all as specified and directed.

Supply,laying and testing cable XLPE insulated ,screened PVC bedded galvanised steel strip or wire armoured,electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 185 Sqmm 3.5 core complete all as specified and directed.

Taking out the old unsv cable for repair in trenches or passing through pipe/fixed to pole/ wall XLPE insualted 240/185/120 Sqmm X 3.5 core armourned heavy duty electric cable and removing from site complete all as specified and directed.

Taking out the old unsv cable for repair in trenches or passing through pipe/fixed to pole/ wall XLPE insualted 95/70/35 Sqmm X 3.5 core armourned heavy duty electric cable and removing from site complete all as specified and directed.

Taking out the old unsv cable for repair in trenches or passing through pipe/fixed to pole/ wall XLPE insualted 16/10 Sqmm X 2/4 core armourned heavy duty electric cable and removing from site complete all as specified and directed.

Supply and fix for DWC high density polythylene pipes having dia 63/50 as per site requirement having corrugation on the wall and plain surface on the wall conforming to IS : 14930 (Part-I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/roof and including all fitting as required and taking out existing complete all as specified and directed.

Supply and fix for DWC high density polythylene pipes having dia 90/76 as per site requirement having corrugation on the wall and plain surface on the wall conforming to IS : 14930 (Part-I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/roof and including all fitting as required and taking out existing complete all as specified and directed.

Supply and fix for DWC high density polythylene pipes having dia 120/103 as per site requirement having corrugation on the wall and plain surface on the wall conforming to IS : 14930 (Part-I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/roof and including all fitting as required and taking out existing complete all as specified and directed.

dinesh enterprises

Standard engineers

Ashoka Engineers

KALSI CONSTRUCTION CO

v k engineers and builders