REPAIR AND REPLACEMENT OF JOINERY, FLOORING, PLASTERING AND MISC BR WORKS AT AJAYMERU, MGS ENLCAVE, HALDIGHATI LINE AND MES SUBORDINATE ACCN AT JAIPUR MIL STN

Amount

M&L post construction ATT of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L Post Construction ATT At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Cutting holes in stone wall not exc half brick built in cement mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed 15 mm thick in CM 1:6 complete all as specified & directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed.

Taking down shutters of any description exc. 1.00 Sqm but not exc. 2.00 Sqm each complete all as specified and directed.

S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed

S & F Factory made Solid PVC Moulded door shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

M&L for factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm).Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm),T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall Continue... (at Serial Item No. 11.01)

M&L in repair for 18 mm thick WPC (Wood Polymer Composite) panel with suitable pins, screws and adhessive in cabinets body, shutters and shelves etc. complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

S&F brass handle of 100mm size, cast type, polished bright complete all as specified and as directed.

S&F aluminium handles cast type anodised of 125 mm size complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

S&F door closer hydraulically regulated designation No 3, universal type, suitable for door shutter of weight between 61 to 80 Kg of aluminium (extruded section) body complete all as specified and directed.

S&F in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for Nylon Medium Door Bottom Seal Strip Brush (aluminium framed) with upto 94 cm long suitable to cover gaps upto 20mm complete all as specified and directed.

S & F auto close hinges, stainless steel, bright finish or electrogalvanised fixed.complete all as specified and as directed

M&L for roller blind curtain (semi blackout) for windows roll-up shades light filtering sun and UV protection polyester curtains with plastic cord/chain, brackets fixed with screws complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

S&F rolled mild steel section in framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

M&L for running welding in repairs , thickness of metal to be welded not exc 6 mm complete all as specified and directed.

M&L for powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately

S&F for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately

S&F powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21, 100 mm long (2 No) , suitable handle (1 No) complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately

M&L in repair anodised aluminium snap grid frame work (size of grid 605 x 605mm) for false ceiling complete all as specified and directed.

S&F Hangers (Size of grid 605 x 605mm) 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L for repairing aluminiun door and window shutter by taking down shutter from frame, opening out joints, taking out glass or panels of any description, replacing the corner piece wherever required, joining and assembly again, refixing the glass pane and panels by provosion of new rubber neoprene packing, roller and latches complete all as specified and directed.

M&L for carried out water roof treatment as under :- (a) Complete removal of existing roof treatement and disposed off the rubbish outside the defence land. (b) Preparation of dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with including WPC @ 3% weight of cement or as per manufactururer instruction. (c) All visible cracks to be opened up in V shape cleaned properly with wire brush washed and filled with cracks filling compound for cracks upto 5mm width / depth of cracks. (d) Cracks of more than 5mm width / depth are filled Continue... (at Serial Item No. 36.01)

Continue... (from Serial Item No. 36.00) with URP cement grouting by injecting through nozzles till refusal by authorisedapplicator of manufacturer, carefully by following manufacture instruction. The size and spacing of nozzles shall be as per manufacturer instruction or as directed by Engg-in-Charge. (e) M&L rendering 10mm thick in cement mortar (1:3) on concrete surfaces to receive water proofing treatment finished even and smooth complete all as specified. (f) Necessary gurantee for 5 years shall be submitted by the contractor. Make :- Cement Grout : Dr. Fixit (Fixit Pidicrete URP Model:301) or equivalent in Fosroc / Choksey chemicals / Sika / Berger (HS Super Grout) or equivalent as approved.

M&L for fibre reinforced, UV resistant elastomeric liquid applied water proof coating over cementitious surfaces, highly elastic and hairline crack bridging capacity (elongation 250-350%), non toxic, VOC complaint water based coated in three layers first being priming coat, forming complete tihckness as metioned by OEM and complete all as specified and directed. Make:- Asian / Berger / Sika or equivalent.

M&L for metal frame ceilling with 12 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid complete all as specified and directed. Note :- The frame work for ceiling shall be measured and paid separately.

M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on treads of step and landing of stair including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for granite (of any type) tiles, 20mm thick, machine cut, in skirting / dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm / 450X 350X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in vertical surface such as dado / skirting / risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick rendering in cement mortor 1:4 complete all as specified and directed.

Laying only interlocking paver block, any shape and size of 60 mm thickness, by vibratory compaction, cutting paver blocks in required size and pattern, filling joints with sand including sand cushing 50 mm thick and sweep out surplus sand complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement with and including integral water proofing compound at rate of 03% by weight of cement or as per manufacturer specification complete all as specified and directed.

M&L for rendering on fair faces of brick work or concrete surface of wall 05 mm thick in CM 1:4 (floating / setting coat) and including liquid WPC as per manufacturer instruction and specification and to be finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement with and including integral water proofing compound at rate of 03% by weight of cement or as per manufacturer specification complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for two coats of cement based paint on new plastered surface of walls including preparation of surface complete all as specified and directed.

S&F figured glass 4 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

S&F figured glass 5 mm thick, pin head type and glazing with aluminium beading in squares exc 0.5 sqm in each pane complete all as specified and directed

Hacking out old broken glass (any thickness, size,quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110 mm bore with out access door complete all as specified and directed.

S&F PVC (SWR) branch piece single (single Y) equal or unequal of 75 mm bore of pipe with access door complete all as specified and directed.

S&F PVC (SWR) branch piece single (single Y) equal or unequal of 110 mm bore of pipe with access door complete all as specified and directed.

M&L PVC (SWR) vent cowl 75 mm complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortor in floor, apron etc complete all as specified and directed.

Dismantling of stone sett paving of any description or thickness laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Demolition of cement concrete un-reinforced in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with nails etc complete all as specified and directed.

MSR INFRATECH (BID ID -3276760)

UNIVERSAL INFRAPROJECT PVT LTD (BID ID -3280165)