COMPREHENSIVE REPAIR OF B/R AND E/M NATURE OF WORK INCLUDING REPAIR TO FANS AND DESERT COOLERS OF ANY TYPE IN MD ACCN UNDER EAST ZONE OF GE (NORTH) AKHNOOOR

Amount

S&F in repair 20 mm dia stainless curtain rod complete with stainless bracket and side caps fixed in position as per site requirement by drilling holes in wall and fixed the bracket with rawl plug and SS screw all as specified and as directed.

Taking down cement plaster of any description on stone or brick walls etc. including racking out joints, hacking for key scrubbing down with water etc.complete all as specified and directed.

Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 15mm thick on fair faces of brick work or cement concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

Applying 3 mm thick water proof putty on old/new plastered surfaces of walls/ceiling incl preparation to receiving paint complete all as specified and as directed.

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint including one coat of cement primer complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper including primer complete all as specified and as directed.

Preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

Preparation of Old plastered and unplastered surfaces of walls by washing, rubbing, stopping brooming down with steel wire brushing and applying two coats of oil bound distemper white/tinted including filling small depressions by putty all as specified and directed.

Preparation of Old plastered and unplastered surfaces of walls by washing, rubbing, stopping brooming down with steel wire brushing and applying one coat of oil bound distemper white/tinted including filling small depressions by putty all as specified and directed.

Preparation of Old decorated surface and applying one coat of Oil bound distemper on ceiling by washing, rubbing, stopping brooming down with steel wire brushing including filling small depressions by putty all as specified and as directed.

Preparation of old surfaces including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efforescent salts and removing oil and greasy spots and applying two coat of cement base paint to walls all as specified and as directed.

Preparation of old treated surfaces of ceiling and applying one coat of white wash, complete all as specified and as directed

Preparation of old treated surfaces of walls (plastered or unplastered) and applying two coats of Apex emulsion paint as in roof projection/chajjas etc complete all as specified and directed.

Preparation of plastered and unplastered surfaces of walls,washing, rubbing, stopping,brooming down surface with steel wire brushes including filling small depressions by putty and applying two coats of interior plastic Emulsion paint 1st quality (White/Tinted) incl priming of surface all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint over a coat of aluminium primer, complete all as specified and directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of anti corrosive synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with one coat of synthetic enamel paint all as specified and directed.

Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern), including all fittings, heads , shoes bends , swan-necks etc complete all as specified and directed.

110mm bore PVC SWR Type-B (Pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber joints fixed in floors etc all as specified and directed.

75mm bore PVC SWR Type-B (Pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber joints fixed in floors etc all as specified and directed.

PVC (SWR) bends any radius 110mm dia with oval access doors fixed in repairs complete all as specified and directed.

PVC (SWR) bends any radius 75mm dia with oval access doors fixed in repairs complete all as specified and directed.

PVC SWR 110mm bore Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps complete all as specified and directed.

PVC SWR 75mm bore Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps complete all as specified and directed.

PVC (SWR)110 mm bore junction single, (Single T) equal or unequal ordinary or inverted with spigot or socket branch with oval access door fixed in repairs all as specified and as directed.

PVC junction, double (double Y), equal or unequal, ordinary or inverted with spigot or socket branch of 75mm bore with access door, complete all as specified and directed.

PVC cowls 110mm bore fixed in repairs complete all as specified and directed.

PVC cowls 75mm bore fixed in repairs complete all as specified and directed.

PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement fixed in repairs complete all as specified.

Rotational moulded polyethylene water storage tanks of 500 litres capacity, three layered (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc. with & including "dismantling water tank exc 250 ltr and not exc 500 ltr in capacity and removing from site, complete all as specified.

Rotational moulded polyethylene water storage tanks of 1000 litres capacity, three layered (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc. with & including "dismantling water tank exc 500 ltr and not exc 1000 ltr in capacity and removing from site, complete all as specified.

S&F ball valve high pressure PTMT with epoxy coated aluminium rod & high density plastic ball 20mm dia bore.

Cleaning and removing all scale and dirt etc from 500 ltrs water tanks and from mouths of circulating pipes etc., complete all as specified.

Cleaning and removing all scale and dirt etc from 1000 ltrs water tanks and from mouths of circulating pipes etc., complete all as specified.

Taking up or down steel water tubing and connections of 20mm bore all as specified and directed.

Mild steel galvanized steel tubing 20 mm bore medium grade with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20 mm bore after cleaning including provn of new fittings all as directed.

Taking up or down steel water tubing and connections of 15mm bore all as specified and directed.

Mild steel galvanized steel tubing 15mm bore medium grade with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15mm bore after cleaning including provn of new fittings all as directed.

Stop valves cast copper alloy with crutch or butter fly handle for bore dia of pipe 15 mm fixed in repairs.

Stop valves cast copper alloy with crutch or butter fly handle for bore dia of pipe 20 mm fixed in repairs.

Angle/ Stop valves (Concealed type), cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions for 15mm bore pipe fixed in repairs, complete all as specified and directed.

Bib tap 15 mm bore with flange, Brass CP, fancy type(long body). with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified and as directed.

15mm bore gun metal globe or gate valve with iron wheel head screwed bith end for iron pipe and fixed in repairs, complete all as specified and as directed.

PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed.

Pillar taps 15mm cast copper alloy CP, fancy type with capstan head, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore.fixed in repairs, complete all as specified and as directed.

Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mm in white colour with integral foot rest incl lime mortar incl making good dismantled floor with PCC 1:2:4 B-0 (using 12.5mm graded crushed stone aggregates), 'P' trap fixed in repairs complete all as specified and directed. Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make specified in list make as approved by GE.

Vitreous china wall hung wash basin with fixing accessories, white, flat back, size 590mm x 490mm x 185mm full pedestal including 15mm bore CP Central hole Basin Mixer with Popup waste system with 450mm long braided hoses for mixing hot and cold water screwed down for iron pipe including 32mm dia waste coupling,waste pipe, cutting for and pinning in ends of brackets or erecting stand porcelain stopper a pair of CI brackets fixed in repair complete all as specified and directed .Make-Jaquar (Lyric) cat part no. LYS-WHT-38801 & LYS-WHT-38301 or its equivalent cat part of make specified in list make, as approved by GE.

Supply only PVC connection 15mm size with PTMT nuts on both ends of length 600mm

C.P Swivel shower of any colour for fixing with 15 mm pipe ,with shower arm of size 195 mm long with bend of 45 degree with flange of any description (minimum weight 40 gm), supplied and fixed in repairs complete.

Plastic water closet seat cover white closed pattern with flat bottom and cover including chromium plated hinges device fixed in repairs, complete all as specified and as directed.

15mm bore brass CP wall mixer with provision for overhead shower arrangement with 115mm long bend pipe on upper side for mixing hot and cold water supply screwed down with connecting legs CP extension nipple & wall flange connector for hand shower arrangement with connecting Legs, wall Flanges & wall bracket for hand shower for mixing hot or cold water, screwed for iron pipe and fixed in repairs, complete all as specified and directed. Make-SOL-6273UPR of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Waste pipe for WHB/Urinal for 32/40mm dia fixed in repair all as specified and as directed.

Waste fittings, brass, chromium plated for stainless steel sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and as directed.

Chromium Plated stainless steel towel rail 20mm dia 'D' type 60 cm long between flanges fixed in repairs Make-Jaquar cat part no. AKP-35711PS or its equivalent cat part of make specified in list make, as approved by GE.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.2 meter long flexible spirochrome flex tube and ABS wall hook including making connections and fixed in repair in position complete in all respect as specified.Make-Jaquar Cat part no. ALD-573 or its equivalent cat part of make specified in list make, as approved by GE.

Stainless steel Soap dish, any type, fixed with plugs chromium plated brass screws fixed in repairs complete all as specified and as directed. Cat part No-AQN-7733 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Toilet paper holder with flap recessed type stainless steel Complete all as specified and directed.Make-Jaquar cat part no. AQN-7753 or its equivalent cat part of make specified in list make, as approved by GE.

Supply & fixing in repair Lid of PVC OHT of capacity 500 Ltr complete all as specified and directed.

Description all as srl item No 63 above, but 1000 Ltr

Corner Sheet glass shelf assembly consisting of 5.5mm thick glass shelf with chromium plated bracket guard and railing 60cm long fixed in repairs Cat Part No AKP 35771P of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. complete all as specified.

Stainless steel sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs, complete all as specified. Make : PRAYAG CAT PART NO 939 & JAYNA CAT PART NO SBSD 05 & JAQUAR MODEL NO JQSBSD 52 & BLUE STAR.

Stainless steel sinks without drainage board made of stainless steel (1mm thick) kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm fixed in repairs as approved, complete all as specified and directed. Make : PRAYAG CAT PART NO 939 & JAYNA CAT PART NO SBSD 05 & JAQUAR MODEL NO JQSBSD 52 & BLUE STAR.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each complete all as specified and as directed.

Taking down and refixing incl resecuring and easing shutters area exceeding 1.00 sqm and n.exc 2.00 Sqm each in the same opening complete all as specified and as directed.

Taking down of shutters area exceeding 1.00 sqm and n.exc 2.00 Sqm each complete all as specified and as directed.

Factory made solid panel PVC door shutter/ cupboard shutter/ kitchen cabinets 30mm thick style wooden texture consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed.

Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. NOTE : Sheet glass required shall be measured and paid for separately under relevant item of BOQ.

Powder coated anodised aluminium window / ventilator( glazed / gauged skeleton shutter ), (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No. ) suitable handle (1 No.) complete all as specified and as directed. NOTE : Sheet glass required shall be measured and paid for separately under relevant item of BOQ.

35mm thick flush shutters, solid core with particle board exterior grade as per IS 2202 of 199 (Part-I) flush door shall be internally lipped as per clause .8.52.2 of SSR Part-I 2009 fixed in repairs complete all as specified & as directed.

30mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( gauzed & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 . Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid seperately under respective item.

Description all as per Item No 78 above, but only glass pane shutter without glazing bars.

Door closer of aluminium (Die cast body), hydraulically regulated, designation No 3, universal type, suitable for door shutters of size 851mm to 1000mm of width and of weight between 61 to 80 kg, ISI marked fixed in repairs, complete all as specified and as directed.

Hacking out old broken galss (any thickness, size, quality or description) for metal frames including punching or drilling out old glazing pins/spring clips, complete all as specified.

3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified.

03 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

5mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified.

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

-Ditto- all as per srl item No 85 here-in-before but fixed in repairs.

Aluminium handle cast type anodised of size 75mm long ISI marked complete all as speicified.

Aluminium anodised barrel tower bolt 100mm extruded section ISI marked complete all as specified.

150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

Taking down and refixing including resecuring and easing shutters area exc 1.00 Sqm but n.exc 2.00 Sqm each in the same opening complete all as specified and as directed.

100 mm butt hinges, medium weight cold rolled mild steel, complete all as specified and as directed.

300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and as directed.

300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy fixed in repairs, ISI marked complete all as specified and as directed.

300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed, complete all as specified.

300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate including supply and fixed in repairs, taking and down the unsv existing complete and supply , ISI marked complete all as specified.

Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and as directed.

Aluminium handle cast type anodised of size 150mm long ISI marked complete all as speicified.

S&F in repair auto hinges 105 degree opening made out of stainless steel, complete all as specified and as directed.

Hasp and staple safety type of aluminium anodised 100 mm long as a cupboard locker.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified and as directed.

Plain cement concrete type B-0 1:2:4 (12.5mm graded crushed stone aggregate) 40mm thick as in sub base of floors complete all as specified and as directed.

100mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in flooring incl glass dividing strip including finishing the top surface even & smooth, using extra cement complete all as specified and directed. NOTE : Glass dividing strips shall be measured separately under the relevant item of BOQ.

Supply only glass dividing strips, 3mm thick and 38mm wide, complete all as specified and directed.

Providing cement concrete type C-1, 1:3:6 ( using 20mm graded crushed stone aggregate), 50 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 grade and 3 parts of sand ( all by weight), complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Green Marble work 18mm to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) inclduing pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Green marble with & including 15mm thick screed bed/base in CM 1:4, roughening/cleaning to existing surface of old concrete floor by picking, sweeping clean and washing down with water to remove dirt/dust and brushing neat cement slurry with 3.0 kg of cement per sqm all as specified and as approved.

Vitrified ceramic tiles(Light shade)10mm thick (square /rectangular) polished, area of each tile n.exceeding 0.36 sqm laid as in floors etc, set and jointed in neat cement slurry and pointed in white/coloured cement to match in light shade including 15mm thick screed bed/base in cement and sand mortar 1:4, complete all as specified.

Vitrified ceramic tiles(Light shade)10mm thick (square /rectangular) polished, area of each tile n.exceeding 0.36 sqm laid as in dado/skirting etc, set and jointed in neat cement slurry and pointed in white/coloured cement to match in light shade including 10mm thick rendering in cement and sand mortar 1:4, complete all as specified.

Non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) in floors etc area of each tiles exceeding 0.18 Sqm but not exc 0.38 Sqm. Set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and as directed.

Description all as per srl item No 109 here-in-before but as in skirting over & including 10 mm thick plaster in cement and sand mortar 1:4, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ractangular) area of each tiles exceeding 0.11 Sqm but n.exceeding 0.18sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement laid over & including 15mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed.

Glazed ceramic coloured tiles (350x250mm)/(450x350mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick back coat layer plaster in cement mortar 1:4, complete all as specified and directed.

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed

Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and as directed.

Description all as per item No.114 above, but except bricks, all as specified and directed.

Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified.

Description all as per item No.116 above, but except bricks, all as specified and directed.

Supply only liquid water proofing admixture conforming to IS 2645-1975 of approved make complete all as specified and directed.(Dosage- @ 200ml per 50Kgs of Bags of cement)

Repair to balcony/facia and soffit of chajjas etc by taking down old plastered surfaces and hacking clearly the edges and corners smooth and rounded for new plastered area exceeding 30sqcm in width or girth & applying rendering 15 mm thick dubbing coat where required to match with the existing thickness in CM 1:4 including formwork/scaffolding work upto height 7.00mtr above ground level of bldg including two coats of apex paint over one coat of primer complete all as specified and as directed.

Taking down of ceiling fan of size 1200/1400mm for safety checking by replacing defective parts and re-fixing the ceiling fan after repairs,all as specified and as directed by Engr-in-charge. (Note:- The unserviceable items like capacitor, Bearings, Bush, Canopy, down rod will be measured and paid separately under respective items as Supply only. However, parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional and making connection by replacing PVC insulated unsheathed cable of copper conduct of size 1.5 Sqmm from ceiling rose/ connector fan (minimum 0.50 Mtr length) including cost of labour for above replacement are deemed to be inclusive in quoted rate all as directed.

Note for item No 120 above : The following items shall be deemed to be inclusive in the unit rate quoted against Sl Item In each job, checking the functioning of fan including its connections, cleaning of fan, greasing of fan and mechanical check i.e. tightening of loose screw, nuts, bolts, etc are inclusive in unit quoted rate.

The above job shall be carried out by trained electrician having sufficient experience .

Replacement of unserviceable parts like rubber bush, clamps, bolts, nuts, washers, safety pin, bearing etc will be paid under respective item here-in-after as supply only through proper documentation.

The entire job will be carried out in Akhnoor station and necessary documents showing qtr No, bldg No supported with user signature shall be prepared as per format directed by Engr-in-charge and will be deposited to concerned JE (E/M) within 24 hrs.

Maitenance of documents ie complaint slip/complaint register & other stationery required shall be of contractor's responsibility.

Necessary T&P such as ladder, required manpower for taking down and refixing after repair shall be of contractor's responsibility.

All types of T&P, PVC insulation tape, minor nuts, bolts, washers etc required for maintaining the services shall be provided by contractor without any cost to the department.

Any fan found defective/not working shall be brought to AGE E/M store yard & re-fixed after repairing.

In case of major defects, entire job shall be completed within 10 days from the date of registration of complaint, failing which penalty charges @100/- per day shall be recovered from the date of registration of complaint.

In case of minor defects, entire job shall be completed within12 hrs from the time of registration of complaint, failing which penalty charges @ 50/- per job shall be recovered from the date of registration of complaint.

The contractor shall maintain a record of all urgent/ routine works and if the work is repeated due to poor workmanship, he shall be liable to repair the same without any extra cost.

Supply only rotor of ceiling fan of any size

Supply only fan canopies for ceiling fan size of 1200mm/1400mm

Supply only gun metal bush of suitable size for ceiling fan 1200mm /1400 mm sweep

Supply only fan bearing suitable for ceiling fan 1200mm /1400 mm sweep (bearing with 8 balls shall be used ) Make:- NBC/TATA/SKF

Supply only down rod for ceiling fan with 15mm dia (of length not less than 45cm and not more than 60cm) with hanging clamps for ceiling fan complete all as specified and directed.

Supply only Rubber reel bushes for ceiling fan of size 1200/1400mm

Supply only 'U' clamp for hanging ceiling fan with all nuts, bolts and washers.

Supply only outer body of ceiling fan of any size

Supply only blades (made of aluminum) suitable for 1400mm sweep ceiling fan of any make with set of screws complete all as specified and directed.

Supply only safety pins 40mm to 50mm long with nuts and bolt with washers for ceiling fan of size 1200/1400mm

Supply only steel screw (for fixing of fan blade) as per site requirement for any make of ceiling fan complete all as specified and directed.

Supply only blades (made of aluminum) suitable for 1200mm sweep ceiling fan of any make with set of screws complete all as specified and directed .

Supply only down rod for ceiling fan with 15mm dia (of length not less than 90cm and not more than 120cm) with hanging clamps for ceiling fan complete all as specified and directed.

Supply only down rod for ceiling fan with 15mm dia (of length not less than 180cm and not more than 210cm) with hanging clamps for ceiling fan complete all as specified and directed.

Painting the ceiling fan 1200mm /1400 mm sweep with one coat of syntetic enamel spray paint as existing colour and writing the MES No- as directed.(Taking down of fan,and re hanging measured under item No.121 here-in-before. Note:- Spray painting of ceiling fan shall be done inside MES complex only.

S&F in replacement un serviceable wall mounted fan of capacity of 450mm sweep Superior low voltage performance energy efficient and More than 2000 RPM Rated Speed at 1850 revolution per minute frequency 50 Hz Rated Voltage 230 V , Pull cord for Speed and Oscillation Blade desig of Aerodynamically designed & Blanced Blade all as specified and directed. Note:- Old Unserviceable wall mounted fan shall be deposited to MES store yard.

S&F in replacement un serviceable wall mounted fan of capacity of 400mm sweep Superior low voltage performance energy efficient and More than 2000 RPM Rated Speed at 1850 revolution per minute frequency 50 Hz Rated Voltage 230 V , Pull cord for Speed and Oscillation Blade desig of Aerodynamically designed & Blanced Blade all as specified and directed. Note:- Old Unserviceable wall mounted fan shall be deposited to MES store yard.

Supply and fixing in replacement of unserviceable energy efficeint Ceiling fan 1200 mm sweep, energy efficient ISI mark with 5 star rating(BLDC) 230 Volts AC 50 Hz, single phase including provision of fixing arrangement, nut and bolt and flexible 3 core of size 1.5 sqmm not less than 0.5 m long complete, writing MES No with synthetic enamel paint all as specified and as directed. Make : Havells cat Part No. ES Neo or equivalent in Bajaj/ Orient./Halonix Note:- (a) The contractor shall given a written guarantee of minimum two years from completion of work. (b) NOTE: Old Unserviceable ceiling fan shall be deposited to MES store yard.

Taking down of exhaust fan any size/capacity after disconnecting cable connection, and refixing same in original position after necessary repair/over hauling including replacement of parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional and making connection by replacing PVC insulated unsheathed cable of copper conduct of size 1.5 Sqmm from ceiling rose/ connector fan (minimum 0.50 Mtr length) are deemed to be inclusive in quoted rate all as specified and as directed. (Note:- Rewinding, over hauling and materials to be replaced shall be measured separately under relevant item of BOQ.)

Note for srl item No 139 above : The following shall be deemed to be inclusive in the unit quoted rate :- In each job checking of functioning of fan including its connections, cleaning of fan, greasing of fan, mechanical check i.e. tightening of loose screw , nuts, bolts, are inclusive in unit quoted rate.

The above job shall be carried out by a trained electrician having sufficient experience.

Defective unserviceable part like fan bush, bearing etc will be paid under respective item here-in-after as supply only.

The entire job will be carried out in Akhnoor and necessary documents showing qtr No, bldg No supported with user signature shall be prepared as per format directed by Engr-in-charge and will be deposited to concerned JE (E/M) within 24 hrs.

Necessary complaint slip/complaint register & other stationery required shall be contractor responsibility.

Necessary T&P such as ladder, helper shall be contractor responsibility.

All types of T&P, PVC insulation tape, minor nuts, bolts, washers etc required for maintaining the services shall be provided by contractor without any cost to the department.

Any fan found defective/not working shall be brought to AGE E/M store yard & re-fixed after repairing.

In case of major defects, entire job shall be completed within 10 days from the date of registration of complaint, failing which penalty charges @100/- per day shall be recovered from the date of registration of complaint.

In case of minor defects, entire job shall be completed with 12 hrs from the time of registration of complaint, failing which penalty charges @ 50/- per job shall be recovered from the date of registration of complaint.

The contractor shall maintain a record of all urgent/ routine works and if the work is repeated due to poor workmanship, he will be liable to repair the same without any extra cost.

Material and labour for winding of Exhuast fan 450 mm sweep of any make with super enamelled copper winding wire of existing gauge (wt of copper winding wire per fan 250 to 500 gms) including cutting and getting out old burnt winding, sleeve work, varnishing with E class insulation varnish, threading, connections with twin core copper flexible wire of size 1.5sqmm of length not more than one meter with each fan complete all as specified and directed. Note :- (i) Motor shall be wound with machine inside MES complex only. (ii) Old burnt wire shall be contractor’s property and necessary credit shall be recovered as per credit schedule.

Description all as per Sl item No 140 here in above but 300 mm sweep

Description all as per Sl item No 140 here in above but 230 mm sweep

Supply only fan bush of suitable size for exhaust fan of the any sweep

Supply only 4 mfd capacity ceiling /exhaust fan condensors. Make:- Asian/ Tyton/ CG/ Usha

Supply only metal louvers of suitable size for exhaust fan of the 450mm sweep

Supply only fan bearing of suitable size for exhaust fan of 450mm sweep including greasing.

Supply only 3.15 mfd capacity ceiling /exhaust fan condensors. Make:- Asian/ Tyton/ CG/ Usha

Supply only metal louvers of suitable size for exhaust fan of the 300mm sweep

Supply only fan bearing of suitable size for exhaust fan of 300mm sweep including greasing.

Supply only 2.5 mfd capacity ceiling /exhaust fan condensors. Make:- Asian/ Tyton/ CG/ Usha

Supply only metal louvers of suitable size for exhaust fan of the 230mm sweep

Painting the exhaust fan of 450mm sweep with one coat of syntetic enamel paint as exiting colour and writing the MES No and return to MES storeyard /user unit from the work shop .as directed by Engr in Charge. Note:- Painting of Exaust fan shall be done inside MES complex only.

All as per item No 152 above but 300 mm sweep

All as per item No 152 above but 230 mm sweep

S&F in replacement Domestic Exhaust Fans for kitchen, 300 mm sweep, 230 volt square type, heavy duty, 1400 RPM, corrosion less mild steel body of motor, plastic/ fibre blade for noise less operation, self operating louvers gives powerful performance round the clock, including necessary cutting, making holes on stone/brick walls where required, fixing arrangement with MS pipe 350 mm dia of required length for protect deshape of stone masonery, suitable hold fast with necessary nut, bolts / screws including taking down existing one writing MES No with synthetic enamel paint all specified and directed. Make- havells model-Ventil Air-DB or equivalent in Bajaj,Crompton, Orient & Khaitan as approved . Note:- Old Unserviceable domestic exhaust fan shall be deposited to MES store yard.

S&F in replacement Domestic Exhaust Fans for kitchen, 450 mm sweep, 230 volt suqare type, heavy duty, 1400 RPM, corrosion less mild steel body of motor, plastic/ fibre blade for noise less operation, self operating louvers gives powerful performance round the clock, including necessary cutting, making holes on stone/brick walls where required, fixing arrangement with MS pipe 350 mm dia of required length for protect deshape of stone masonery, suitable hold fast with necessary nut, bolts / screws including taking down existing one writing MES No with synthetic enamel paint all specified and directed. Make- Havells Model-Turbo force or equivalent in bajaj, Crompton, Orient, Khaitan as approved. Note:- Old Unserviceable domestic exhaust fan shall be deposited to MES store yard.

S&F in replacement Exhaust fan single phase sturdy engineering plastic, AC 230 Volt, 50 Hz, 900 RPM of size 300mm sweep with louvers shutter complete with all accessories including connecting up from ceiling rose complete all as specified and directed. Make:- Cat part No:- Turbo Force 1P Grey of Havells or its Equivalent cat part of make-BAJAJ,CROMPTON GREAVES, GEC, KHAITAN,ORIENT as approved by GE Note:- Old Unserviceable domestic exhaust fan shall be deposited to MES store yard.

Supply and fix in replacement exhaust fan of 250mm sweep made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding all as specified and directed. Cat Part no.- Ventil Air DB(green) or equivalent in bajaj, Crompton, Orient, Khaitan as approved. Note:- Old Unserviceable domestic exhaust fan shall be deposited to MES store yard.

S&F in replacement Exhaust fan 200 mm sweep 230 volt square type, heavy duty with louvers of PVC body including necessary nut, bolts / screws writing MES No with synthetic enamel paint all specified and directed. Make-Havells Cat Part No- Smart Ventil air(white) in bajaj, Crompton, Orient, Khaintan as approved or its Equivalent cat part of make. Note:- Old Unserviceable Exhaust fan shall be deposited to MES store yard.

Taking down aluminum/copper point wiring on & including hard wood battens, surface conduit and board/ blocks etc or through conduits for light, socket or power point, fan point complete (Taking down of fittings such as switches, sockets, bells, ceiling rose, holders , regulators light fittings, MCB, lamps etc shall be measured and paid seperately) and making good the disturbed plaster surfaces of wall, floor, ceiling and apply 2 coat of white wash/distemper to meet the existing surface and removing materials and debris to outside the premise neat and clean complete all as specified and directed.

Point wiring for 5 Amp switch /sockets independent using approved colour coding as per IS with 1.5 sqmm single core PVC insulated, unsheathed FRLS cable 1100 volts grade ISI 694 marked, multi stranded with copper conductor drawn through and incl concealed PVC conduit heavy duty, 19/20mm dia, ISI marked with accessories in wall/roof/ceiling etc incl terminal boxes fabricated with 1.6mm MS/ cast iron sunken boxes duly painted with two coats of anticorrosive paint over a coat of red oxide primer on surface in touch with wall and synthetic enamel paint over a coat of red oxide on other side, covered with 3mm thick plastic laminated sheet for mounting switches, regulators, sockets etc including 1.5 sqmm (nominal area) copper conductor PVC insulated, unsheathed, multi stranded FRLS cable as earth wire and connected to earth dolly complete all as specified and as directed. Note:- (a) Switches, sockets outlets, blanking plate, Light fittngs, fans, bells & regulators will be measured and paid for separately.

Sub main wiring with PVC insulated unsheathed FRLS 1100 volts grade multi stranded copper conductor cable 2 runs of 4 sqmm drawn through in and incl suitable size PVC conduit and all accessories fixed to wall/floors/concealed along with 1 runs of 2.5 sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring all as directed. Note: 2 runs of 4 sqmm cable along with one run of 2.5 sqmm cable for earth conductor alongwith suitable size PVC casing capping/Pipe shall be measured as one length.

Sub main wiring with PVC insulated unsheathed FRLS 1100 volts grade multi stranded copper conductor cable 2 runs of 6 sqmm drawn through in and incl suitable size PVC conduit and all accessories fixed to wall/floors/concealed along with 1 runs of 4 sqmm PVC insulated unsheathed copper conductor multi stranded cable 1100V grade as earth continuity conductor and connected to common earth dolly including taking down existing sub main wiring all as directed. Note: 2 runs of 6 sqmm cable along with one run of 4 sqmm cable for earth conductor alongwith suitable size PVC casing capping/Pipe shall be measured as one length.

Taking down and dismantling geyser of any make and cap 25/50 ltrs & taking out water inlet outlet assly, removing glass wool and taking out the inner tank, descaling the assembly and tank , detecting the leakage, welding / brazing the defected part , repacking the glass wool and refixing the same after making it funcional including replacement of worn out nuts bolts washer etc complete all as specified and directed. Note: The unsv items shall be measured as supply only under relevant items of sch A.

Supply only water inlet and outlet assembly of any make as required at site with rubber gasket suitable for geyser of 25 ltrs capacity complete all as specified and directed .

Supply only water inlet and outlet assembly of any make as required at site with rubber gasket suitable for geyser of 50 ltrs capacity complete all as specified and directed .

Supply only thermostat switch for electric water heater storage type of cap 25/ 50 ltr, 230 volts of any make of geyser.

S&F in replacement heating element with triangular base ISI marked, single phase, 230 volt, of wattage 1.5 KW. All as specified and directed.

S&F in replacement heating element with round base suitable for Bajaj geyser having electronic cutout plate ,ISI marked single phase, 230 volt, of wattage 1.5 KW all as specified and directed.

Supply only indicator lamps round/rectangular type 230 volt AC suitable for geyser of any capacity including providing electric connections complete all as specified & directed.

Supply & fixing in replacement water storage inner tank of SS material for 25 ltrs capacity geyser,incl supply and fixing 15mm dia galvanized air release valve all as specified and directed.

Supply & fixing in replacement water storage inner tank of SS material for 50 ltrs capacity geyser, incl supply and fixing 15mm dia galvanized air release valve all as specified and directed.

Supply & fixing in replacement MCB SPN 20 Amps 240 volts , rupturing cap 10 KA, 'C' series all as specified and directed.

Supply & fixing in replacement MCB DB 2 way single door complete with fixing accessories all as specified and directed.

Supply & fixing in replacement thermal cut out Bimetallic disc type with snap action switch, with operation temperautre below the boiling point i.e. 90+ 6˚C with manual reset knob for Geyser.

Supply and fixing in replacement plug top 15 Amps 3 pins all as specified and directed. Make Havells REO, Schnieder, Indiasian

Material and labour for painting of geyser of cap 25/ 50 ltr complete with superior quality synthetic enamel white paint by spray painting after scraping old paint and making surface clean all as specified and directed. Note: contractor has make an arrangement for spray painting within premises of Garrison as directed and specified by Engr -in-charge and rate quoted deemed to include to remove, transport Geysers from bldgs to specified loc for cleaning and painting and reconnected at same place after doing needful.

Supply and fixing in replacement electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece incl making holes on walls for proper fixing with nuts and bolts complete making the surface good as per existing all as specified and directed. Make Godrej/Havells(Monza EC),or equivalent as approved. Note:- Old Unserviceable geysers shall be deposited to MES store yard.

S&F for replacement heating element with triangular base ISI marked, single phase, 230 volt, cap 2 KW all as specified and directed.

S&F for replacement heating element with round base ISI marked, single phase, 230 volt, cap 2 KW all as specified and directed.

Supply and fixing in replacement pressure release valve conforming to 15mm bore suitable for fixing with GI pipe/tubing 15mm bore complete all as specified and directed.

Supply and fixing in replacement of heavy duty PVC connection nylon threaded 450mm large (18”) 15mm bore including brass nuts, rubber washers complete on both ends.

S&F in repair white/ warm white powder coated CRCA housing with LEDs 36W, 230 V, 50 Hz Surface mounting LED 2 feet x 2 feet luminaries, Sweamless front frame with flat white light transmission acrylic cover complete with all accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified. Cat Part No-BZRSQL of Bajaj or its equivalent of Havells, Orient,Philips, Wipro as approved by GE.

CHOPRA CONSTRUCTIONS (BID ID -3071866)