SPL REPAIR TO BLDG NO GA 85 AND CONVERSION LT OVERHEAD ACSR CONDUCTOR INTO UNDERGROUND CABLE AND CERTAIN REVENUE WORK AND MINOR WORKS AT BAGRAKOTE UNDER GE SEVOKE ROAD

Amount

Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge or thickness as in roof covering complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section any position as in framed works complete all as specified and as directed.

S&F rolled mild steel Roof trusses (framed), trussed, purlins, crane, gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc( Fe 410-W Gde-E-250) quality A Including preparation of surface and one shop coat of zinc chromate primer at contractors workshop before fabrication complete all as specified and directed by Engineer-in-Charge..

S&F rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe 410 W Gde-E 250 Quality A complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

S&F mild steel screw bolt, 5 to 10mm dia machine made with hexagonal head at one end screwed the other or screwed both end, each screwed end to be fitted with washer and one hexagonal or square nut exceeding 05cm and not exceeding 10cm long complete all as specified and as directed.

S&F mild steel work (miscellaneous) as in wind ties for roof, flat iron fillets (for securing wire mesh etc) including drilling holes for securing bolts and fixed with bolts and nuts etc and similar work conforming to Fe-290.Gde-E-165, complete all as specified and as directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded. complete all as specified and as directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F 3mm thick glass sheet ordinary quality & glazing with oil putty in square not exc 0.50 Sqm in each pane all as specified & directed.

S&F pressed steel frames (Size-165X60mm) for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate etc complete all as specified .

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in block for hold fast, filling in frames, copings or similar work and finished the surface with existing including form work complete all as specified and as directed.

S&F factory made 2nd class hard wood rail and style 35mm thick plain framed, panelled shutter (two panel ) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 (part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F factory made 2nd class hardwood rail and style 35 mm thick Glazed and skeleton shutter open rebated and prepare to receive glass, gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing gauge etc size of members of shutters as specified in SSR part-I Section 8 and clause 8.24(a) of second class hard wood all as specified

S&F mild steel tower bolts stove enamelled black with bright bolt 200 mm long complete all as specified and as directed.

S&F 300 mm long mild steel sliding door bolts plate type stove enamelled black with bright bolts not less than 12mm dia with and including a minimum of 6 bolts nuts, four on bolts plate & two on staple plate complete all as specified and as directed.

S&F mild steel pressed handle oval type stove enamelled black 150 mm long complete all as specified and as directed.

S&F 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, Fe 290 Gde-E-165 complete all as specified and directed.

Dismantling wall & ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified

S&F 605X605mm anodised aluminium snap grid frame work for false ceiling including 2.5mm dia mild steel wire galvanized class 3, @ 60cm centre to entre and fixed to steel or wooden member including 4mm thick non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and croos tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm)

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above GL) complete all as specified

M&L 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection & paving finished even & smooth without using extra cement complete all as specified and as directed.

S&F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlines to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles Fe-290 Gde-E-165 complete all as specified and directed.

Demolition of brickwork built in cement mortar including disposal of debris, etc outside MD land, complete all as specified and directed.

M&L for brick work with sub class 'B' brick straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all specified and directed by Engineer in Charge .

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified

M&L rendering 15mm thick in CM 1: 6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 20mm thick on fair faces of brick work or concrete surfaces in CM 1:4 including mixing WPC as per manufacturers instruction, finished even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured seperately.

Supply only integral water proofing compound complete all as specified and as directed.

Complete removal of existing treatment on wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed

M&L for preparation of new or untreated surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whiting on wall complete all as specified and as directed

Complete removal of existing treatment on wall surfaces and applying two coats of distemper oil emulsion over a coat of chalk whiting on wall complete all as specified and as directed .

M&L for preparation of new or untreated surfaces of walls and applyingtwo coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed

M&L for preparation of new untreated wood and wood base material of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new primed steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L for preparing new steel and iron surfaces of any description n.exc 10 cm in width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L RCC 1:2:4 , type B1, 20mm graded stone aggregate as in lintels upto 1.5m clear span and lintel band, roof band and other similar items including form work all as specified.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire annealed, not less than 0.9mm dia or securing with clips complete all as specified.

All as per item No.45 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for rendering in CM (1:4), 10mm thick on fair faces of brick work or concrete surfaces for fixing of wall tiles complete all as specified and as directed.

M&L for screed bed or bedding layer of cement mortar 1:6, 20mm thick for laying floor finishes complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface 450X350X7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Taking down 15 mm bore GI pipe line including fittings and removal to store or cleaning for re-fixing complete all as specified and as directed.

Taking down 20 mm bore GI pipe line including fittings and removal to store or cleaning for re-fixing complete all as specified and as directed.

S&F 15 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all specified and directed.

S&F 20 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all specified and directed.

S&F Bib taps, cast copper alloy fancy type with crutch or butterfly handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule complete all as specified and as directed.

S&F 15mm bore gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

Dismantling of 100 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) branch piece single (Single `T') equal or unequal with access door complete all as specified & directed.

S&F garting doom 125 mm dia with waste hole of PTMT complete all as specified and as directed

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m in depth for foundation, shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n exc 1.5 in depth and getting out in soft / loose soil complete all as specified and as directed.

M&L for PCC 1:3:6 Concrete bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested; in 100mm bore pipes complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Surface dressing n exc 15cm deep in hard/dense soil complete all as specified and directed.

M&L 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregated) as in sub base complete all as specified.

M&L PCC 1:2:4, type B0 (using 12.5mm graded stone aggregate) as in copings, kerbs and the like incl weathering, slightly rounded or chamfered angles and throating, as directed incl necessary form work as reqd complete all as specified and as directed

M&L 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 M-35 grade, laid as directed to any shape. Complete all as specified and as directed

M&L for Sand filling under floors or in foundations including watering and consolidation as in sand cushioning for interlocking paver blocks complete all as specified and directed.

M&L for broken stone boulders Hardcore of gauge exc. 63 mm but n exc 100mm , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L for Continuous brick edging; with width equal to the depth of the brick, laid dry, on edge with fly ash modular bricks complete all as specified and as directed.

Excavation in trenches not exc 1.5 Mtr wide and not exc 1.5 Mtr deep in hard/dense type soil getting out and levelling of bottom surface to required level complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for moorum/red bajri filling in floors pavings, laid in layers n.exc 15 cm thick spread levelled and rammed including watering complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4, type B1 (using 20mm graded stone aggregated) as in sub base complete all as specified.

M&L for 40mm thick PCC 1:2:4, type B0 (using 12.50mm graded stone aggregated) for DPC to horizontal or vertical surfaces including necessary from work incl mixing WPC as per manufactures instructions complete all as specified and as directed.

S&F Steel ventilators with top hung shutter including hinges,steel peg stay, complete all as specified.

M&L for screed bed or bedding layer of cement mortar 1:6, 15mm thick for laying floor finishes complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and as directed.

M&L mild steel round bars, 6mm dia conforming to Fe 410W, quality A of Fe 290 as in reinforcement to half brick wall (two Nos in every fourth course of half brick wall) complete all as specified and as directed.

S&F PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube fixing in opening complete all as specified and directed.

S&F factory made soild panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed togehter with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and directed.

S&F 100mm Long Stainless Steel Butt Hinges, medium weight , cold rolled complete all as specified and as directed

S&F 100mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F for aluminum anodized barrel tower bolts of extruded section, 150mm long, ISI marked, complete all as specified.

S&F vitreous china squatting pan Orissa pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including fittings complete all as specified.

S&F PVC valveless, syphonic action type flushing cistern low level, 10 litre capacity with it's complete accessories, fixed complete incl connection to water pipe and PVC 32 mm dia flush pipe etc complete all as specified and directed.

S&F PVC connection 15mm dia with PTMT nuts of length 450mm. Complete all as specified and as directed.

S&F 15mm bore angle stop valves fancy type cast copper alloy chromium plated with long shank and cup (concealed type), screwed both ends for iron pipe or for union and fixed including taking down of old unserviceable one complete all as specified and as directed

S&F Brass chromium plated shower rose 125mm size complete all as specified and as directed

Preparation of newly plastered surfaces and applying three coats of white wash on walls complete all as specified and as directed

M&L for preparation new steel surfaces of any description over 10cm width of grith and applying two coat of synthetic enamel paint complete all as specified and directed.

S&F PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement

Supply and fixing stainless steel soap dish fixed to wall with screws complete all as specified.

S&F Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks 1000 Lit capacity double layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F 20mm bore gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

M&L for 25mm bore PTMT ball valve, high pressure, with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair 25mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed

S&F PVC vent cowl 75 mm dia complete all as specified and as directed.

S&F Pillar Taps 15mm bore fancy type copper cast alloy with capstan heads chromium plated screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe.

Excavation over areas not exceeding 1.5 m deep and getting out in soft / loose soil complete all as specified and as directed.

Excavation over areas exc 1.50 m and n.exc 3.00 m complete all as specified and as directed.

M&L cement concrete 1:3:6, Type C-2 (using 40mm graded stone agg) as in foundation, filing and mass concrete complete all as specified and as directed.

M&L Providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks ( for use with masonry), string courses, copings kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, boundaries ( for stone walling) corbwls, brackets, etc. ( of any section indicated) with plain fair faces, including chamfers weatherings throating etc. and setting in mortar complete with joints to match, type B-1(20mm graded aggregate) Set in CM1: 4 complete all as specified and as directed.

M&L Providing precast cement concrete in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain with plain fair faces, including chamfers weatherings throating etc. and setting in mortar complete with joints to match, type B-1(20mm graded aggregate) Set in CM1: 4 complete all as specified and as directed.

M&L for RCC M25 (design mix) in slabs supported on walls, beams and coloumns in floors, roofs, landing, baloconies, canopies, deck slabs ans in shelves and the like complete all as specified and directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

S&F mild steel TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coh, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to complete all as specified and as directed.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement.

M&L for 15mm thick rendering on other than fair faces of brick or concrete surfaces in CM 1:4 with mixed water proofing compound @3% of cement, finished even and smooth with using extra cement complete all as specified and as directed.

M&L rendering 20mm thick on stone or other than fair faces of brick surfaces in CM 1:4 surface finished even and smooth without using extra cement complete all as specified.

S&F cast iron soil, waste and vent pipes, in any length with or without ear with cement joint, fix on wall 75 mm bore sand cast pipe complete all as specified and as directed.

S&F Cast iron soil cowl 75 mm dia complete all as specified and as directed.

Supply 150 mm internal dia of salt glazed stone ware drain pipes grade A laid in trenches and jointed as specified and as directed.

M&L for Cutting openings, through brick walls for door, window and other penings or enlarging existing openings.converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and as directed.

M&L for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for Brick work with fly ash bricks as in half brick thick wall built in CM (1:4), complete all as specified and directed.

M&L 100mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified.

S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F (EWC) Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) incl all fittings complete and fixing to flush pipe and outlet pipe complete all as specified and as directed

S&Fvitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified.

S&F urinal spreader of PTMT, any colour, fixing with 15mm dia pipe (minimum weight 60 gm) complete all as specified and as directed.

S&F Vitreous China wash basins, white, flat back, size 550x400mm excluding taps, waste but including brackets complete all as specified and directed.

Supply only 32 mm waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement & other end fixed complete all as specified and as directed.

S&F low density 32mm bore polythene waste pipe (LDPE) complete all as specified and as directed.

S&F two way bib cock with wall flange chromium plated with crutch or butterfly handle screwed down screwed for iron pipe 15 mm bore and fixed complete all as specified and as directed.

S&F 15mm bore CP Toilet Hand Pressed Nozzle (Heath faucet) with 1.5 meter long tube with CP wall bracket complete all as specified and as directed.

S & F 75mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified & directed.

Cutting chases in brickwalls girth exc 10 cm but n exc 20 cm , pinning in making good to facings where required and pointing in cement mortar 1:3 for conceal water tubing etc and making good complete all as specified.

M&L for cutting holes into or throgh brick walls built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required area not exc 150 sqcm including making good to complete all as specified.

M&L steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 (including preparation of surfaces and one shop coat of zinc chromate primer) at contractors workshop before fabrication complete all as specified and as directed.

M&L for PCC 1:2:4 type B-2 (40 mm graded stone aggregate) as in cement concrete in surface channels and drains complete all as specified and as directed.

Excavating over areas not exceeding 1.5 m deep and getting out in hard /dense soil complete all as specified and as directed.

Excavating over areas exc 1.50 m and n.exc 3.00 mm deep and getting hard/dense complete all as specified and as directed.

Preparation of new non AC Board surface and applying three coat of white wash.

M&L for brick work with sub class 'B' brickstone one and half brick thick honey comb walls built in cement mortar 1:4, complete all as specified and directed.

Loose filing with broken bricks aggregartes of gauge 80 to 150 mm in soakage pits wells complete all as specified and as directed.

S&F CI manhole covers 600 mm dia complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

Cutting existing steel tubing for alterations or additions (Each cut measured) 20 or 25 mm bore pipe complete all as specified and as directed.

Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and as directed.

S&F 25 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all specified and directed.

S&F 25 mm bore medium grade galvanized steel water tubing with all fittings and laid in trenches complete all specified and directed.

S&F Rotational moulded polyethylene water storage tanks 500 Lit capacity double layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Taking down carefully copper/Aluminum point wiring light fan, socket or power complete (fittings such as switches ceiling roses pendants, regulators, sockets, sketch light fittings, tube light fittings etc. to be measured separately if found serviceable) and removing unserviceable materials from site of work and segregating serviceable materials for safe custody and making good to disturbed surfaces of walls, floors, etc. including disconnecting of ceiling fan/exhaust fan complete all as directed

M&L for point wiring for light/fan/call bell etc. controlled by one switch with 1.50 Sqmm (nominal area) FRLS PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable drawn through and unsheathed single core solid copper conductor cable of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, including rigid PVC concealed conduit (Medium Grade) of suitable size, with all fittings and accessories including provision of mild steel terminal boxes of suitable size made with 1.2 mm thick mild steel sheet duly galvanised and suitable for fixing switches / sockets / regulators etc. fixed in recess of wall with brass chromium plated screws and cap washer complete for one light / fan point controlled by one switch all as specified and directed.

All as per item No. 154 here-in-before but for 5/6 Amp socket point on independent board -ditto-

All as per item No.154 here-in-before but with 2.5 Sqmm cable for 15/16 Amp socket point on independent board and 2.5 sqmm solid copper cable for earth continuity conductor.

S&F Switch piano flush type, single pole, one way, 5/6Amp complete all as specified and as directed.

S&F Switch Socket combination, 2-in-1, 3 pin, 5/6 Amps flush type complete all as specified and as directed.

S&F Switch Socket combination, 5-in-1, 5/16 Amps flush type complete all as specified and as directed.

S&F Ceiling rose, surface bakelite, 3 terminals complete all as specified and as directed.

S&F electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 / 1400 mm sweep 120 watts complete all as specified and as directed.

S&F LED tube light fittings 4 ft, 20w with aluminium batten heavy quality complete with side holders.

S&F SPN MCB of capacity 32 Amps, 240 volts, C curve, 10 KA breaking capacity complete all as specified and as directed.

Supply and fixing 25 watt LED street light luminaires with highly efficient lighting in & including mounting bracket made out of GI pipe light grade 25-40mm bore not less than 01 mtr long duly fixed with wall with fixing arrangement such as clamps, nuts, bolts complete all as specified and directed by the Engr in charge.

S&F MCB, SP,240 volts, breaking capacity 10 KA C curve, rating 6 to 32 amps, complete all as specified and as directed.

Taking down old serviceable/unserviceable ceiling fan, connecting wire etc and keeping at site for reuse at site after carrying out repiar works to building/rewiring complete all as specified and directed by the Engr-in-charge

Supply and fixing energy efficient, 5 star rated BLDC ceiling fan 1200 mm sweep without remote, with all acceesories and connecting up with the ceiling rose with new flexible wire of suitable size complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of the earth plate not less than 1.5 m below ground level, connected to GI earth wire 4mm dia by means of bolts, nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I, connected to earth test point all as specified or indicated including excavation and connected earth work in soft / loose soil, P.C.C 1:3:6 type C-1 as in pit, 20mm dia GI pipe light grade for watering pipe, 15mm bore GI light grade earth lead protection pipe, 50mm thick R.C.C. 1:2;4 type B-1 cover slab of earth pit reinforced with 8mm dia TMT bars @ 10cm C/C both ways and with handle made out of 10mm dia bars, funnel, strainer, including salt & charcoal and testing on completion including dismantling unserviceable earthing complete all as specified and as directed.

S&F Sheet Metal enclosure( IP-43) for SPN DBs,08Ways, double Door, suitable for mounting DP MCB as incomer & SP MCBs as outgoings, built- in bus bars complete suitable for 240 Volts, AC, 50 Hz supply, and fixed in recess in brick masonary wall all as specified and as directed

Dismantling & taking down aluminium service wire of any size including necessary disconnection from the pole / main switches etc. all as directed complete

Dismantling house service bracket any type from the wall including making good the disturbed surface complete

Supply and laying in trenches or passing through pipe 1100 volts grade armoured heavy duty XLPE insulated electric cable with aluminium conductor of cross sectional area 10 sqmm 2 core complete all as specified and as directed

S&F GI Pipe 25mm bore light grade fixed for cable protection along with wall all as specified and as directed

Supplying & laying in trenches clear Sand for cushioning of under ground cable 8 cm below and 15 cm above complete in level all as specified. Note:- Punned thickness shall be measured

M&L for laying of sub class 'B' common burnt clay brick for protection of cable and flat and width wise along the axis of the trench complete all as specified and as directed.

Supply, laying connecting and testing galvanised steel water tubing light grade nominal dia 50 mm for protection of cable as required at site complete all as specified and as directed.

Supplying laying connecting and testing XLPE insulated , sheathed armoured heavy duty electric power cable with aluminium conductor 1100 volts grade and having cross sectional area 70sq mm 3.5 core complete all as specified and as directed.

Supplying laying connecting and testing XLPE insulated , sheathed armoured heavy duty electric power cable with aluminium conductor 1100 volts grade and having cross sectional area 50sq mm 3.5 core complete all as specified and as directed.

Supplying laying connecting and testing XLPE insulated , sheathed armoured heavy duty electric power cable with aluminium conductor 1100 volts grade and having cross sectional area 25sq mm 3.5 core complete all as specified and as directed.

Supplying laying connecting and testing XLPE insulated , sheathed armoured heavy duty electric power cable with aluminium conductor 1100 volts grade and having cross sectional area 10sq mm 4 core complete all as specified and as directed.

Supplying laying connecting and testing XLPE insulated , sheathed armoured heavy duty electric power cable with aluminium conductor 1100 volts grade and having cross sectional area 35sq mm 3.5 core complete all as specified and as directed.

Supplying laying connecting and testing XLPE insulated , sheathed armoured heavy duty electric power cable with aluminium conductor 1100 volts grade and having cross sectional area 6sq mm 2 core complete all as specified and as directed.

Supply and fixing thermoplastic polycarbonate street light junction box suitable for protection IP 66/67 "weather proof" for outside installation with metric knockout entry for cable of size 10-25 sqmm and size 155x210x92mm with terminals and provision of one MCB SP 6A complete with fixing arrangements on 40mm dia GI pipe 1 mtr long (light grade) with necessery clamps incl necessery cable connections all as specified and as directed of Make Hensel/ Sintax/C&S. Note: Rate of all necessery connected items such as MCB SP, GI pipe, clamps etc are deemed to be included in quoted rates.

S&F steel tubular swaged poles type 410 SP-22, 8.5 mtr long complete with CI base plate and finial taper plug bolts nuts and screws complete all as specified and directed

Supply & fixing of weather proof PVC insulated copper conductor cable 1.5 sqmm 3 core duly inserting the cable inside the pole including making hole on top and bottom on the steel pole complete all as specified and as directed.

Boring in road/PCC foot path for passing the cable through GI pipe 50mm complete all as directed by Engr-in-charge (GI pipe will be measured in relavant item)

Dismantling existing ACSR/Earthwire (any size) from over head line complete all as specified and as directed.

Dismantling insulators any type and any size complete all as specified and as directed.

Dismantling of cross arm( made of MS channels/angles etc) or clamps etc complete and stacking aside for re-use/replacement all as sepecified and as directed.

Dismantling of stay assembly embedded in concrete and removing materials from site of work complete all as specified and as directed

M&L for PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in foundation, filling or for mass concrete of poles, stays, struts or any other indicated work including from work (if required) complete all as specified and as directed.

M&L for PCC 1:2:4 type B-2 (20 mm graded stone aggregate) for coping of poles/platform of feeder pillar box or any other indicated work including form work (if requiered) duly palstered and making the surface smooth and even by using extra cement complete all as specified and as directed.

Excavation in trenches exc 1.5 mtr in depth, and n.exc 3 mtr in depth for laying of pipe/cables/ Poles and getting out in soft/loose soil complete all as specified and as directed.

Design, supply, erection, testing and commissioning of outdoor type LT feeder pillar box, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Copper bus bar for distribution system and type tested at CPRI, fabricated in factory having modern fabrication and testing facility which includes seven (07) tanks pre treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032. The feeder pillar shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.15mm thick CRCA mild steel sheet and 3.15mm thick gland plate duly compartmentalized for each control gear and bus-bar, front door (02 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and mild steel channel (75 MC) base frame at bottom. The feeder pillar shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings and all as shown in drawings :- CONTROL WIRING : All control wirings shall have to be carried out with 1100 volts rated FR grade PVC insulated multi-flexible type copper wire of cross sectional area 1.50Sqmm and shall be properly bunched, tied and dressed, ferrule marked for proper identification and crimped with suitable size and type of tinned copper lugs and shall be wrapped with PVC spring type tube near the door hinges. INCOMING : 4 pole MCCB (with center off) having breaking capacity 25 KA and adjustable thermal & magnetic setting and of rating 100 Amps. - 01 No. OUTGOINGS : (a) 4 pole MCCB (with center off ) having breaking capacity 16 KA and adjustable thermal & magnetic setting and of following ratings :- i) 80 Amps - 01 No. (i) 63 Amps - 02 No. (ii) 40 Amps - 02 Nos. (iii) SPN MCB 32 A, C curve, 10 KA-10. MISCELLANEOUS ITEMS : (a) Bakelite fuse holder with 5 Amps HRC type control fuse - 03 Nos. (b) LED Pilot Lamp suitable for 230 Volts AC supply with integral circuit and cluster LED of following colours : (i) RED - 01 No, (ii) YELLOW - 01 No, (iii) BLUE - 01 No. (c) Danger Notice Plate duly written in Signal Red colour on aluminium plate in English and Hindi language and of size not less than 150mmx100mm - 02 Nos. (Note : The Feeder Pillar Box shall be designed in such a way that adequate workable space is made available inside the compartments and the size of the feeder pillar

Design, supply, erection, testing and commissioning of outdoor type LT Bus Bar Chamber box, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars (32mm x 5mm) for looping & branch connection system .The chamber shall be painted with powder coated paint (Shade : RAL-7032) after 7 tank pre-treatment of surfaces. The bus bar chamber shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The bus bar chamber shall be made out of 3.15mm thick CRCA mild steel sheet and 3.15mm thick gland plate , front door (01 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and mild steel channel (75 MC) base frame at bottom. The bus bar chamber shall be provided with ventilation facility in the form of louvers for better heat dissipation. The chamber shall consist of the followings and all as shown in drawings :- (a) Incomming- MCCB, 4 Pole of rating 80Amps, breaking capacity 16KA, adjustable thermal magnetic release of make Legrand, cat Part No 420013 - 01 Nos. (b) Outgoing- 4 Pole of rating 63Amps, breaking capacity 16KA, adjustable thermal magnetic release-2 4 Pole of rating 40Amps, breaking capacity 16KA, adjustable thermal magnetic release-2 MCB, SPN of rating 32 Amps ‘C’ series having breaking capacity 10 KA - 8 Nos. MCB, TPN of rating 32 Amps ‘C’ series having breaking capacity 10 KA - 4 Nos. (b) Bakelite fuse holder with 5 Amps HRC type control fuse - 03 Nos. (c) LED Pilot Lamp suitable for 230 Volts AC supply with integral circuit and cluster LED of following colours : (i) RED - 01 No, (ii) YELLOW - 01 No, (iii) BLUE - 01 No. (d) 02 Nos.Danger Notice Plate duly written in Signal Red colour on aluminium plate in English and Hindi language and of size not less than 150mmx100mm shall be fixed on both front & rear door of the bus bar chamber. (Note : (a)The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments

Design, supply, erection, testing and commissioning of outdoor type LT Bus Bar Chamber box, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars (32mm x 5mm) for looping & branch connection system .The chamber shall be painted with powder coated paint (Shade : RAL-7032) after 7 tank pre-treatment of surfaces. The bus bar chamber shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The bus bar chamber shall be made out of 3.15mm thick CRCA mild steel sheet and 3.15mm thick gland plate , front door (01 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and mild steel channel (75 MC) base frame at bottom. The bus bar chamber shall be provided with ventilation facility in the form of louvers for better heat dissipation. The chamber shall consist of the followings and all as shown in drawings :- (a) Incomming- MCCB, 4 Pole of rating 63Amps, breaking capacity 16KA, adjustable thermal magnetic release of make Legrand, cat Part No 420013 - 01 Nos. (b) Outgoing- 4 Pole of rating 40Amps, breaking capacity 16KA, adjustable thermal magnetic release-2 MCB, SPN of rating 32 Amps ‘C’ series having breaking capacity 10 KA - 10 Nos. MCB, TPN of rating 32 Amps ‘C’ series having breaking capacity 10 KA - 4 Nos. (b) Bakelite fuse holder with 5 Amps HRC type control fuse - 03 Nos. (c) LED Pilot Lamp suitable for 230 Volts AC supply with integral circuit and cluster LED of following colours : (i) RED - 01 No, (ii) YELLOW - 01 No, (iii) BLUE - 01 No. (d) 02 Nos.Danger Notice Plate duly written in Signal Red colour on aluminium plate in English and Hindi language and of size not less than 150mmx100mm shall be fixed on both front & rear door of the bus bar chamber. (Note : (a)The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments

Design, supply, erection, testing and commissioning of outdoor type LT Bus Bar Chamber box, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type Aluminium bus bars (32mm x 5mm) for looping & branch connection system .The chamber shall be painted with powder coated paint (Shade : RAL-7032) after 7 tank pre-treatment of surfaces. The bus bar chamber shall be provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The bus bar chamber shall be made out of 3.15mm thick CRCA mild steel sheet and 3.15mm thick gland plate , front door (01 layer) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and mild steel channel (75 MC) base frame at bottom. The bus bar chamber shall be provided with ventilation facility in the form of louvers for better heat dissipation. The chamber shall consist of the followings and all as shown in drawings :- (a) Incomming- MCCB, 4 Pole of rating 40 Amps, breaking capacity 16KA, adjustable thermal magnetic release of make Legrand, cat Part No 420013 - 01 Nos. (b) Outgoing- MCB, SPN of rating 32 Amps ‘C’ series having breaking capacity 10 KA - 15 Nos. MCB, TPN of rating 32 Amps ‘C’ series having breaking capacity 10 KA - 4 Nos. (b) Bakelite fuse holder with 5 Amps HRC type control fuse - 03 Nos. (c) LED Pilot Lamp suitable for 230 Volts AC supply with integral circuit and cluster LED of following colours : (i) RED - 01 No, (ii) YELLOW - 01 No, (iii) BLUE - 01 No. (d) 02 Nos.Danger Notice Plate duly written in Signal Red colour on aluminium plate in English and Hindi language and of size not less than 150mmx100mm shall be fixed on both front & rear door of the bus bar chamber. (Note : (a)The bus bar chamber Box shall be designed in such a way that adequate workable space is made available inside the compartments

S&F in repair ventilation fan with louvers single phase 230/240V of size 200mm sweep polycarbonate body, low noise and weight and removable screwless front for easy cleaning including making holes on wall and making good the distributed surface with all connecting arrangement complete all as specified and directed.

S&F LED tube light fittings 2 feet, 9w with aluminium batten heavy quality complete with side holders.

S&F Sheet Metal enclosure( IP-43) for SPN DBs,02Ways, suitable for mounting DP MCB as incomer & SP MCBs as outgoings, built- in bus bars complete suitable for 240 Volts, AC, 50 Hz supply, and fixed in recess in brick masonary wall all as specified and as directed

Cutting existing steel tubing for alterations or additions (Each cut measured) 40 or 50 mm bore pipe complete all as specified and as directed.

S&F in repair 25mm bore globe or gate valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe and fixed complete all as specified and directed.

Supply and fixing GI pipe 40mm light grade for passing the cable under road complete all as specified and directed.

Supply and fixing LED street light fittings including lamp (minimum 72W rating), separate individual peanut plated Lens housing should be made of LM6 Pressure die Cast Aluminum . Optical cover should be only Toughened Glass only, Impact Resistance >IK05, IP Protection not less than IP 66, Protection should be Class I vibration should be as per IEC 60598, Product Standard IS 10322/IEC 60598, Driver Operating Voltage should be 140 V-270V, Driver Frequency 50Hz, Power Factor>0.9, Lumen output should not be less than 100 Lumen/watt and Luminaries driver ckt should be moulded type weather proof construction with separate surge protection device 5kA rating and separate connector block for termination of incoming cable connection including bracket made out of GI pipe 40mm bore medium grade, 1.5 mtr long bent ot shape as directed including suitable clamp of FI 50 x 6mm with nuts, bolts & washers complete all as specified and directed. Note : (i) Being a highly humid area the driver of LED fitting shall be moulded type weatherproof type.

S&F Ridid non-metallic PVC conduit (medium) fixed with FI clamps, nuts and bolts of suitable size with nuts & bolts for protection of connection wires, connection from junction box to light fittings, complete for outer dia 20 mm complete all as specified and directed.

M/s. STRUCTURES INDIA

RAJIV DEY SARKER

AJOY PAUL

NARESH GUPTA

M/S JANARDAN SHARMA AND SONS