SPL REPAIR TO OR MD ACCN BLOCK NO P-29(06 QTRS) IN GSE COLONY OF 340 SUPPLY ASC AT OLD CANTT, PATIALA MIL STN

Amount

Taking down cement plaster on brick walls built in cement mortar including raking out joints and concrete surfaces as in wall or ceiling etc. including hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L Rendering 15mm thick on brick surface in Cement mortar 1:4, finishing surface w/o using extra Cement, mixed with integral liquid water proofing compound complete all as directed and specified.(Note WPC to be paid separately)

Supply only integral water proofing compound.

M&L 10mm thick cement plastering in cement mortar 1:6 on fair faces of brick work surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L 5 mm thick cement plastering in cement mortar 1:3 on concrete ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for Applying one coats of exterior weather emulsion paint to old exterrnal walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc including preparation of surface complete all as specified and directed.

M&L for Applying 02 coats of exterior weather emulsion paint to new exterrnal walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer and wall care putty to smooth the surface including complete removal of existing treatment complete all as specified and directed.

M&L for Applying one coat of oil bound distemper to old wall surfaces including preparation of the surface complete all as specified and directed.

M&L for Applying 02 coats of oil bound distemper to new wall surfaces over & including a coat of interior wall primer and including applying wall care putty to smooth the surface complete all as specified and directed.

M&L for Preparation of surfaces and applying one coat of oil bound distemper to old ceiling surfaces including preparation of surface complete all as specified and directed.

M&L for Preparation of surfaces and applying 02 coats of oil bound distemper to new ceiling surfaces over & including a coat of interior primer on ceiling surfaces including applying wall care putty to smooth surface complete all as specified and directed.

Demolition of cement concrete in floors and pavings n. exc 15 cm thickness below or above ground level, complete all as specified and directed.

M&L 50mm thick, PCC 1:3:6, type C-2 using 20 mm graded stone aggregate, as in plinth protection finished even & fair without using extra cement complete all as specified and directed .

M&L 25mm thick, PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate), as in floor, sub base finished fair & even without using extra cement complete all as specified and directed .

M&L 75mm thick, PCC 1:3:6, type C-2 (using 40mm graded stone aggregate), as in sub base complete all as specified and directed .

Dismantling floor hearth or wall tiling including cement mortar bedding, removing serviceable tile to store and rubbish off the premises.

M&L Single charge, Ceramic,scratch resistant, joint free, premium quality coloured tiles 600 X 600 mm and 8-10 mm thick, as in floors etc. in any pattern of light tiles as approved, set and jointed in neat cement slurry & including 15mm thick rendering in cement mortar (1:4) and pointed in white or coloured cement to match, in floors etc.pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for anti-skid ceramic joint free premium quality coloured tiles 300 X 300 mm and 7-8 mm thick, as in floors etc. in any pattern of light tiles as approved, set and jointed in neat cement slurry & including 15mm thick rendering in cement mortar (1:4) and pointed in white or coloured cement to match, in floors etc. and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L Ceramic glossy finish, joint free premium quality coloured tiles 450 X 300 mm and 6-7 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for Baroda Green marble, machine cut as in shelves/steps/cills/jambs/skirting/border only in tile flooring and the like works and flooring etc,( 14-16) mm thick including bull-nose the front length, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing over 15 mm thick screed bed in CM 1:4 complete all as specified. Note : Single piece should be used in steps/cills/jambs/shelves.

Machine cut kota stone slab as in flooring of size 580 x 580 mm each & 18-20 mm thick, set and jointed in cement slurry over & including screed of 15mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : 1. All the edges of slabs shall be grinded/cutted at the right angle before laying, so that paper thin, smooth jointing to be obtained. 2. The colour of the slabs shall be uniform.

M&L for machine cut kota stone slab as in skirting of 18-20 mm thick, set and jointed in cement slurry over & including screed of 10 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified

Dismantling loose/disintegrated portion of RCC Chajjas, bands, shelves, beams, column or slab and similar work including support if required and stitching of cracks with MS U clamps of 8mm dia @ 150mm c/c with inserting concrete block strecthner with cement mortar 1:3 mixed with adhesive chemical (polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with 10mm thick plastering in CM 1:4 finished even & smooth without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

Taking down chowkhats or frames of any description exc 1.5 Sqm and n. exc. 4 sqm each (without taking off shutters from the frame) including cutting hole to size for receive fresh PCC of hold fast and making good the disturbed surface same complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

S&F factory made Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,size 125x60mm

M&L PCC (1:3:6 ) type C 0 using 12.50 mm graded aggregate as infilling in PS Chowkhats alll as specified .

S&F factory made flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood incl two coat of synthetic enamel painting over a coat of pink primer complete all as specified and incl supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 150mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 150mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F factory made 35mm thick glazed and skelton shutters of 2nd class hard wood open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40mm) incl two coat of synthetic enamel painting over a coat of pink primer complete all as specified and including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 3Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf

S&F Powder coated 50 microns extruded aluminium for doors & windows complete all as specified and as directed by Engr in charge

S&F stainless steel (304 grade) finished butt hinges 100mm complete all as specified and directed.

S&F powder coated aluiminium tower bolt 150mm long complete.

S&F powder coated aluminium handles 150mm complete.

S&F powder coated aluminium hook and eye of suitabel length adjustable to aluminium window shutters compelte.

Supply only stainless steel wire cloth 0.36mm nominal dia of wire and 1.40mm avg width of apreture.

S&F stainless steel tubing of 25 mm dia chromium plated (0.5- 1.0) mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Taking up or down steel tubing and connections incl cleaning for refixing or removing to store yard of size 15mm bore.

S&F of CPVC pipes of 20 mm outer dia with SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors for external water supply all as directed and specified by Engr in Charge

Taking up or down steel tubing and connections incl cleaning for refixing or removing to store yard of size 20mm bore.

S&F of CPVC pipes of 25mm outer dia with SDR 11 & plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors for Internal/External water supply all as directed and specified by Engr in Charge

S&F flushing cistern of PVC 10 ltr. cap. with single flushing system, , white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.

M&L for Vitreous china squatting pan of Orissa patten size 580 x 440 white , fixed in repair complete and making good to floor in CM 1:3 all as directed and specified.

S&F vitreous china premium/1st quality wash basin , white/ivory/off white, flat back, size 500x400 mm including screws & plug and brackets etc. in repair all accessories as recommended by manufacturer complete in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified and directed by Engr in Charge.

S&F stainless steel sink with drainage board, AISI 304 quality grade, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling of 32mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 940mm x460/ with bowl size 407x 355x229mm in repair and making good disturbed portion in CM 1:3 or PCC 1:2:4 as directed by Engr in Charge

S&F Stainless steel plate rack made out of 1 mm thick stainless steel sheet of size 900x750x250mm in repair (wt not less than 4kg) complete all as specified and as directed.

S&F 15mm bore basin mixer with popup waste system , fancy type, cast copper alloy, with capston head chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts as in repair complete all as specified and directed by Engineer in Charge.

S&F 15mm bore Sink mixer with connecting legs and wall flanges, wall mounted fency type chromium plated cast copper alloy screwed down high pressure, screwed ends and fixed in position in repair complete all as specified and directed by Engineer in Charge.

S&F wall mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlet for hot and cold water with connecting legs and wall flange fancy type suitable for 15 mm tubing fixed in position complete all as specified and as per sample.

Supply and fixing in repairs 15mm bore C P Angle cock .

S&F Towel rail 600mm long brass chromium plated fancy type, fixed as in repair complete all as specified and directed.

S&F Brass chromium plated shower roses 125mm size with swivel joint and with shower arm any size fixing in repairs all as directed and specified.

S&F 450mm long PVC connection of approved quality with brass check nuts at both ends for 15mm bore pipe complete all as specified and directed.

S&F Bib tap cast copper alloy chromium plated, fancy type, with capstain head handle screwed down screwed for iron pipe and fixed fo 15mm bore pipe after taking down of old brass bib tap complete all as specified.

S&F in repair double layered rotational moulded polyethylene (White Colour) water storage tanks (cylindrical vessal with closed top/ cover) 500ltrs capacity hoisted and fixed in position all as specified including 25mm PVC brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore pipe and including GI nipple/ union of 20mm GI bore to connect to PVC tank complete all as specified.

M&L 20mm bore, gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

M&L for PVC multifloor trap / nahni trap 100 mm dia and 450mm long including jointing with solvent cement fixed in repair complete all as specified and directed by Engineer in Charge.

S/F PVC(SWR) gully traps, 125 x 125mm size , square or roundmouthed, including grating fixed in repair complete all as specified abd directed.

Supply and fixing in repairs MS powder coated peg set of Six complete.

S&F in repairs stainless steel soap dish approx size 100x80mm fixed to walls of approved make complete all as specified.

S&F in stainless steel grating of 100 mm dia for floor/nahni traps complete all as specified and directed

S&F UPVC pipes (SCH-40) fixed to walls 100 mm bore including stack clamps, nut bolts etc. and making necessary connections, fixed in repairs complete all as specified and directed by Engineer in Charge..

S&F UPVC pipes (SCH-40) fixed to walls 75 mm bore including stack clamps, nut bolts etc. and making necessary connections, fixed in repairs complete all as specified and directed by Engineer in Charge..

S&F 100mm bore UPVC pipes (SCH-40) laid in trenches or in floors complete.

S&F 75mm bore UPVC pipes (SCH-40) in any length with or without ears with cement joints laid in trenches or in floors complete.

S&F PVC (SWR) bend of 100 mm bore as directed by Engr in Charge

S&F PVC (SWR) bend of 75 mm bore as directed by Engr in Charge

S&F PVC (SWR) vent cowl 100 mm dia.

S&F PVC Tees bend upto 150mm dia as directed by Engr in Charge

Taking down eaves, gutters and rain water pipes (any sizes or pattern) incl all fitting incl cleaning for refixing or removing to store yard.

S&F PVC(HDPE) SWR , 110 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction, fixed to walls complete all as specified including fixing of pipe to wall with flat iron clamps of size 25 x 3mm, bolts, washers, nuts, nails etc, after taking down existing damaged rain water pipe complete all as specified and directed.

S&F PVC(HDPE) SWR , 110 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction laid in trenches or floor and making good the disturbed portion to match with surrounding area complete all as specified and directed by Engineer in Charge.

PVC(SWR) bends for 100mm dia rain water pipes with rubber ring joints complete all as specified and directed

S&F 6mm thick looking mirror with smooth finish edges/sides fixed to wall etc. complete fixed in position all as specified and directed.

Dismantling of brick tiles or terracing tiles single layers on roofs complete all as specified.

Demolition of mud in roofs any thickness including plastering and leaping complete all as specified and directed.

Scarping surfaces of roof by wire brushing and removing all loose dust and cleaning and washing down the surfaces with water complete all as directed.

M&L for PCC 1:2:4 type C-1 using 20 mm graded stone aggregates as in padding over roof, minimum thickenss at khurra as 25 mm to maintain a slope of 1:100, complete all as specified and directed.

S&F Applying membrane on primed surface by press application or torch application method with minimum 75 mm longitudinal wise lap and 100 mm over lap on the transverse direction duly sticked using 3 mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished non woven polyester reinforced (wt not less than 150 grams) over applying one coat of bituminous primer @ 0.4 kg per Sqm complete all as specified and directed.

S&F factory made, un-reinforced precast cement concrete tiles of size 250mm x 250mm x 22mm, machine pressed, as on roof surface, confirming to IS 1237-1980, laid over and including 15mm thick screed bed in CM 1:6 incl mixed with WPC (Water proofing compound shall be paid separately), set jointed and pointed with grey cement slurry complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of rgroove with cement mortar 1:3 complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregates) as in roof kerbs, benches and water troughs etc. including necessary moulding complete all as specified & directed.

Demolition of brick work including all quoins arches pillars etc built in cement mortar.

M&L for brick work in cement mortar (1:6) using sub class 'B' bricks staight or curved on plan exc 6.0 m mean raidus.

S&F framed work such as grills, gratings, etc, with ends of bars shoulderd and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work conforming to Fe

S&F framed work of grade Fe 410-W (Gde E-250) quality A as in doors or gates of angle or cooler stand or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L for ACP sheet of 4mm thickness of approved plain colour/shade for chajjas/sun-shades/cladding and the like works etc. fixed to frame work of MS/aluminium/hollow sections of any size description including finishing all the joints with silicon or as per manufacturer's instructions complete in all respect and complete fixed in position incl scaffolding/ladders etc as required and also making the joint between wall and chajjas/sun-shade water proof all as specified. Note : Frame Work shall be measured and paid separately.

S&F MS hollow rectangular/square tubes/pipes of YST 310 Grade as in frame work for roofs/sheds/chajjas etc and like similar items including welding/fixed with conn plates etc. including one coat of red oxide zinc chrome primer complete all as specified.

Preparing new surface of steel material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete..

Excavation in trenches in soft/loose soil not exceeding 1.50 Mtr wide and not exceeding 1.50 Mtr in depth and getting out in soft/loose soil complete all as specified and directed Engineer-in-Charge

M&L PCC (1:4:8) type D-2 (using 40mm graded mechanically crushed stone aggregate) as in foundation of manholes complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position complete all as specified

M&L RCC (1:2:4) type B-1 using 20mm graded mechanically crushed stone aggregate as in precast slabs for covers of manholes and set in CM 1:6 incl necessary from work hand placing of manhole cover on varsion complete all as specified and directed by Engineer-in-Charge. Note : Contractor to meniton month and year of casting to be engraved on each MH covers. No extra cost to be paid for this the same will be inlcuded in the above item.

M&L TMT bars 8mm dia and over cut to length bent to shape required incl cranking bending, spirally , hooking ends and binding with mild steel wire not less than 0.9mm dia (annealed) complete all as specified and as directed by Engineer-in-Charge. (Note : The payment shall be made only after placing of cover on manholes)

Returning and filling incl spreading, levelling, water and well ramming in layers not exceeding 25cm thick complete all as specified and directed Engr-in-charge

Removal of excavated material n. exc 50 M and depositing where directed at a level not exc 1.5 M above the starting point

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and formingbranch channel (1/2 round or 3/4section) in cement concrete 1:2:4 mix type B-1smooth finished and reforming benching as required of any size of dia of pipe.

M&L Cement concrete (1:2:4) type B-1 using 20mm graded machnically crushed stone agg as in benching of manholes coping, plinth course, bands, stops, bed plates etc incl necessary form works complete all specified and directed by Engineer-in-Charges

S&F 16 mm thick HDHMR board of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

S&F 16 mm thick HDHMR board of single side rigid laminate of approved colour and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet, cupboard shutters and shelves complete as per manufacturer’s instructions complete all as specified and directed.

S&F piano hinges mild steel 40mm width , complete all as specified and directed .

S&F Ball bearing runners (25-50)mm Telescopic (KTS-20) full extension load capacity 50 kgs,

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified.

S&F Stainless Steel 304 grade wire Basket (avg. wait 3.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required suze complete fixed in position all as specified.

S&F stainless steel finished locks with 2 nos of keys min outer body size 75mm suitable for wardrobes/CB/ Aluminium door etc. complete all as specified.

M&L for coloured chequered tiles 30cm x 30cm x 25mm thcik with grey cement and pigment, set jointed and pointed in neat cement slurry as in floor/path complete all as specified and directed.

M&L for efflorescence treatment of walls including (a) Removing existing plaster over the affected bricks to be removed . The affected bricks to be completely exposed complete all as specified and directed. (b) Apparent visible efflorescence to be first cleaned using hard wire brush and all cyrstal deposits to be removed. The bricks shall then be cleaned using soft brush of powdery crystals removed. Then make a 1 to 4 solution of vinegar and water (1 part vinegar to 4 parts water) and apply it to the efflorescence affected area using a nylon brush. Allow the vinegar/ water solution to sit on the surface of the affected area for 15 minutes, but do not allow the solution to dry. Rinse the area with clean water, using low pressure jet. Two cycles of cleaning using vinegar water solution to be repeated complete all as specified and directed. (c) The joints of bricks so cleaned shall be pointed using cement putty made a site using Sika Latex/SBR polymer diluted at ratio of 1:4 with water. The solution so made shall be used to be mixed with cement to make a putty consistency paste. The cement putty shall be then worked out in the joints which are clean and in SSD condition. (d) The bricks so pointed shall be cleaned of all dust or deposit using brush. A undiluted single component acrylic polymer-Sika Raintite, to be used to prime the brick surface. The primer while being tacky the first coat of water proofing coating is done, second coat is applied after a time interval of 4-6 hours after the first coat has dried. The water proofing coating shall be two component polymer modified cementitious coating-Sika top seal-107, having a thickness of 1.5mm in two coats. The material to be factory batched and ready to use. The two components shall be mixed using low speed drill having a RPM 350-450 and fitted with a paddle. The mixing to be done for 3-4 mintues to give a brush able consistency mix. The coating shall be done using brush 100-150mm wide brush. It is to be take care that material while being used is agitated every 3-5 mintues to avoid powder part getting settled. The water proofing coating shall have below properties Tensile Strength - 4.56 N/mm2 after 14 days exposure (According to ASTM D 2370) Bond Strength 2.0 N/mm2 at + 27o C (failure in substate). After application of second coat and while the material is still wet, coarse sand is sprinkled over the coating so as to ensure proper mechanical key is provided for subsequent plaster. (e) M&L for plastering 15mm thick over the treated surface shall be done with 1:4 cement sand plaster added with acrylic polymer-Sika Plastocrete Plus, @ 3% by weight of cement.

S&F 12mm thick high density fibre board pre-laminated on both sides (water proof) below & above middle/lock rail in powder coated aluminium doors and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc aluminium beads 20 mm size with and complete all as specified and directed.

Taking down carefully existing points wiring on surface conduit/concealed conduit including conduit from surface and expect conduit in concealed wiring for light/fan/socket/power/bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, pieces of wires, gutties, conduit, wooden boards etc removing materials to store for keeping in safe custody of contractor for which the credit has been considered under schedule of credit and making good the disturbed portion of all floor, ceiling etc all as specified and directed.

Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan/bell in new PVC conduit to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed by Engineer in-charge Note-I-(Switches and regulators shall be measured and paid for separately). Note-II- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- (The cost of modular cover plate and metal flush boxes is deemed to be included in the unit rate quoted for this item). Note -IV - cost of Eye/bottle thimbles used for connection in switches/sockets & MCBs in DBs is deemed to be included in the unit rate quoted for this item. Note:- V- Rate of cutting chasing included in the unit rate quoted for this item

All as per Sl item No 111.00 above herein before but one socket out let 5 pins 5 Amp on the same board with other switches complete all as specified and directed.

All as per Sl item No 111.00 above herein before but for one socket out let 5 pins 5 Amp on independent board complete all as specified and directed.

All as per item No.111.00 herein before but 2.5 Sqmm PVC insulated and unsheathed FRLSH single core multistranded copper conductor incl 2.5 Sqmm PVC insulated and unsheathed FRLSH copper earth wire for switch socket combination 3 pin 15 amps on independent board.

S&F Modular switch 1 way, 6 Amps, 1 module, 230 volts complete all as specified.

S&F Modular switch 1 way, 16 Amps, 1 module, 230 volts complete all as specified.

S&F Modular bell push switch 1 way, 6 Amps, 1 module complete all as specified.

S&F Call bell ding dong AC 230 volt single pole complete all as specified.

S&F Modular socket 5 pin 6 Amps, 2 module 230 volts complete all as specified.

S&F Modular socket 5 pin 6 &16 Amps, combination type 2 module complete all as specified.

S&F Modular Fan regulator step type, 120 watts, 2 module complete fixed as in repair all as specified.

S&F ceiling rose surface bakelite surface 65 x 50mm 3 terminals all as specified & directed

Lamp holder including LED bulb 9 W including flexible wire 0.5 Sqmm copper cable all as specified & directed by Engr-in-charge.

New generation energy saving and environmental friendly long life LED building security light 1x35 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with 32mm bore light grade GI pipe bemd to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed by Engineer-in-charge.

Surface Mounted LED Bulk Head Luminaire of capacity 10 watt with ABS Body & Polycarbonate Diffuser, IP54 inc connection with ,with flexible wire 0.5 sqmm copper cable all as specified & directed by Engr-in-charge.

M & L for Sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:-2(two) Runs of 6.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 6.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note 2 :(i) Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc. 10 cm girth . (iii) Including taking out/down existing unserviceable sub main wiring.

M & L for Sub main wiring with two single core 4.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 4 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 4.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 4.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring.

MCCB, 4 Pole, 63 A, 16 KA for fixing in DB including proper thimble connection, thermal and magnetic release protection complete all as specified and directed by Engineer-in-charge.

Supply and fix epoxy power coated MCCB distribution box double door VTPN 4 way vertical type AC 415 V with IP 54 protection for MCBs alongwith provision of MCCB as incomer with commen bus-bar at incoming end of outgoing MCBs grouted/ flush to wall, complete all as specified by Engineer-in-charge. (Note :- MCCB will be measured and paid under seperate item) (i) Cost of Eye/bottle thimbles used for connection MCBs in DBs shall deemed to be included in unit rate quoted for this items, (ii) Electric wiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth. (iii) connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped. all the vacant holes of the DB shall be provided with blank plates of appropriate size.

Supply and fix Sheet metal enclosure 8 ways double door for DBs when MCBs are to be used 240,volts including 200 Amps standard bus bar of suitable size and common neutral link all flush mounting type, drilling holes for incoming and out going cables with IP 43 protection complete all as specified & directed by Engr-in-charge.

Supply and fix MCB , SPN, 240 Volts ,40-63 amp for fixing in DBs of including proper thimble connections complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB, single pole 240 volts 6 to 32 Amp capacity for fixing in DB’s including proper thimble connections complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with galvanized iron earth plate electrode of size 600x600x6.0mm , buried directly in ground (earth pit not less than 2.25 mtrs below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts , nuts , check nuts and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate 20 mm dia watering pipe medium grade 1.70 mtr long with a plug at top, GI protection pipe light grade 15 mm dia from earth pit to main board including PCC pit in cement concrete 1:2:4 along with CI frame and cover 10mm thick duly hinged to CI frame as shown in the electrical plate No3 of SSR 2009 part 1 specification at page 497.

Supply and fix Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in square LED Batten 18/20W 6500K of capacity ,20 watt,4 ft long incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed by Engr-in-charge.

Supply and fix in replacement of elegantly designed sleek surface mounted pressure die-cast aluminium LED luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver of capacity 20 W LED of 5000 K and making good the existing surface as per existing complete all as specified & directed.

Supply and fix Exhaust fan AC single phase 230/240 v of size 300 mm sweep 900 rpm metal body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including hole making Louver complete all as specified and directed by Engineer-in-Charge.

Taking down and refixing of ceiling fan,Exhaust fan & geyser after necessary cleaning painting marking serial No complete all as specified and directed by Enginner-in-charge.

Supply and fix Exhaust fan AC single phase 230/240 v of size 250 mm sweep 900 rpm Engineering thermoplastic body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including hole making Louver complete all as specified and directed by Engineer-in-Charge.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and as directed by Engineer-in-charge.

S & F modern energy efficient bedroom Muziris wall decorative light of capacity 20 watt single headed 240 volt, IP20 rating, controller type (push button), product weight 1.04 kg, body material (metal), power source (corded electric),Lamp base E27, Colour(bronze) incl electrically connection , including removing of unserviceable decorative light fittings of any description complete all as specified and directed by Engr-in-charge. Make: Philips model No 31425 or as equivalent in crompton /havells/wipro/halonix.

Buttar Construction Co. (BID ID -3480683)

FAVOURITE ENGINEERS (BID ID -3480690)

m/s panchmukhi builders (BID ID -3480310)

AR CONSTRUCTIONS (BID ID -3480275)

M/S RAJ KUMAR GUPTA (BID ID -3478408)

DELTA CONSTRUCTION CO (BID ID -3480620)

Jawandha Enterprises (BID ID -3481531)

KK BUILDERS (BID ID -3480982)

Arneja Builders (BID ID -3477143)

ANIL KUMAR AND CO (BID ID -3481480)