NIT-04/PR/BSPTCL/2026-3

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed. .All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in :Ali kinds of soil.

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead

Supplying and filling in plinth with local sand under floors including, watering, ramming consolidating and dressing complete.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion)Along the external wall below concrete or masonry apron using chemical emulsion @ 2.55 litres per linear metre including drilling and plugging holes etc.With chlorpyriphos E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor.With Chlorpyriphos EC 20% with 1% concentration

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for Brick work in superstructure above plinth level upto floor V cum.

Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS :12894, in superstructure above plinth and upto floor V level.Cement motar 1:4 (1cement : 4coarse sand)

Extra for providing and placing in position 2Nos. 6mm dia. MS bars at every third third course of half brick masonry (with F.P.S. brick)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level.1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 40mm nominal size)

1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work @ 1 kg per 50kg of cement.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mmnominal size, well rammed and consolidated and grouted withfine sand, including finishing the top smooth

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum ceAll work upto plinth levelment content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M-25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum ceAll work upto plinth levelment content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll work from plinth level upto floor V level Concrete of M-25 grade with minimum cement content of 330 kg/cum

Plasticizer/super plasticizer

Centring and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc.for mass concrete.

Centring and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

Centring and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centring and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centring and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts

Centring and shuttering including strutting, propping etc. and removal of form for: Stairs,(excluding landings) except spiral-staircaces.

Centring and shuttering including strutting, propping etc. and removal of form for: Edges of slabs and breaks in floors and walls Under 20 cms wide

Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete excluding plastering of the jambs, sills and soffits.50 mm thick

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets. Thermo-Mechanically Treated bars TMTC-500-8mm dia

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets. Thermo-Mechanically Treated bars TMTC-500-10mm dia

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets. Thermo-Mechanically Treated bars TMTC-500-12mm dia

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets. Thermo-Mechanically Treated bars TMT Fe-500- 16mm dia

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets. Thermo-Mechanically Treated bars TMT Fe-500- 20mm dia

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets. Thermo-Mechanically Treated bars TMT Fe-500- 25mm dia

Providing desination 100 A one brick flat soling joints filled with local sand including cost of watering texes, roualty all complete as per building specification and direction of E/l.

Providing and fixing flush door shutters decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including Stainless Steel butt hinges with necessary screws.

Providing and fixing flush door shutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:Extra for cutting rebate in flush door shutters {total area of the shutter to be measured)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap bading shall be paid in basic item.) 6 mm thick High performance glass

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing S.S. sliding door bolts (aldrop) with nuts and screws etc. complete:250x16mm

Providing and fixing SS door latch with necessary screws etc. complete. 250x12 mm

Providing and fixing SS handles "D" type with required fastners (Screws) complete: 250x19 mm (Pipe dia)

Providing and fixing SS hanging floor door stopper with necessary screws etc.complete: 150 mm Rubber Stopper

Providing and fixing SS sliding tower bolt with required fastners (Screws) complete: 250x10 mm

Providing and fixing SS sliding baby latch with required fastners (Screws) complete: 100 x 10 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite black

Extra for fixing marble / granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except begundy, bottle green,black of any size as approved by Engineer-in-chage in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 (1 Cement:3 Coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300 x 300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20mm thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement motar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 60 x 60 cm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

12mm cement plaster of mix: 1:6 (1 cement : 6 coarse sand)

20mm cement plaster of mix : 1:4 (1 cement : 4 coarse sand)

6mm cement plaster to ceiling of mix:1:4 (1 cement : 4 coarse sand)

Extra for providing and mixing water proofing material in proportion recommended by the manufacturers:20mm cement plaster 1:4(1 cement : 4 sand)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.Two or more coat on new surface.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeNew work (Two or more coats applied @ 1.43 ltr/ 10 sqm.over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm).

Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Supplying and filling good quality cinder in downslabs etc, all complete as per building specification and direction of E/I.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Extra for providing and fixing ceiling to curved surfaces in narrow widths

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if requird angle threshold of mild steel angle of section 50x25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge.Profile B

Providing and filling (Back filling) profile "B" pressed steel door frame back hallow portion with cement concrete mix of 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 10mm nominal size)

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. all comlete.Fixed to steel windows by welding

Providing and supplying aluminium extruded tubular and other aluminium sections as per the rchitectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture,as per the approved sealant design, within and all around the perimeter for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural esigner, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified,as per the approved shop drawings and as directed by the Engineerin-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by BL(National Accreditation Board for Testing and Calibration Laboratories),Department of Science &Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories 1. Performance Laboratory Test for Air Leakage Test (- 50pa to –300pa) & (+50pa to +300pa) as per ASTM E-283- 04 testing method for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME-331-09 testing method for a range up to 2000 ml.” 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testing method for a range upto 2000 ml”

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm” 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in- Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and laying instant setting spray applied Polyurithene foam (CFCfree). Waterproofing System on the roof slabs at F-4 levels of average thickness not less than 10mm (Nominal Dencity of foam not less than 60 kg/cum.) as per manufactures specification following by providing a coat of brush applied waterproofing coating with cold applied Neoprane based Rubberised elastomeric bitumen (with minimum 500%Elongation at break), applied @1 km/ms. followed by proving and apeading 120GSM Non Owen Geotextile all complete as per direction of engineer-in-charge.)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Brick work with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ).

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send).

15 mm cement plaster on rough side of single or half brick wall of mix.1:6 (1 cement: 6 coarse sand)

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C pan of size 580 x 440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lif, 10 litre low level white vitreous china flushing cistern & C.P flush bend with fittings & C.I brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I brackets, 15mm C.P brass pillar taps, 32mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450mm with a pair of 15mm C.P brass pillar taps.

Providing and fixing counter basin size- (mm) 190x550x430 (Jaquar,CAT NO- FLS-wht-5701) including fixing and all accessories as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions G.I. clamps, complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: Range of three urinal basins with 10 litre white P.V.C. automatic flushing cistern

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.White Agaria Marble Stone

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 510x1040mm bowl depth 178mm

Provding and fixing PVC waste pipe for sink & wash basin including PVC waste fittings complete Semi rigid pipe 40 mm dia

Provding and fixing 600X450mm beveled edge mirror of superior glass complete with 6mm thick hard board ground fixed to wooden cieats with CP brass screws & washers complete.

Provding and fixing Toilet Paper.holder Vitreous china

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezodial shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour. Weighing not less than 88 gms.

Provding and fixing PVC Soil ,Waste & vent pipes all complete 110 mm dia

Provding and fixing PVC Soil ,Waste & vent pipes all complete 40 mm dia

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 mm vent cowel

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 mm plain bend

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 mm door bend

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 X 110 mm dia door tee

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 X 110 mm dia plain-y

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 mm pipe clip

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 X110 mm dia p-trap

Provding and fixing PVC fittings all complete as/specification & directionof E/I 110 mm dia X 45 Bend

Provding and fixing PVC fittings all complete as/specification & directionof E/I 40 mm elbow

Provding and fixing PVC fittings all complete as/specification & directionof E/I 40 mm plain tee

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 32 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 40 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 50 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the 15 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the 20 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the 25 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the 32 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 32 mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality. 20 mm Nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality. 25 mm Nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality. 32 mm Nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality. 40 mm Nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality. 50 mm Nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions.45 cm length 15 mm Nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end). 32mm nominal bore Vertical

Providing and fixing C.P. brass bib cock of approved quality conforming to IS :8931.15 mm Nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm Nominal bore

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm Nominal bore

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms.

Constructing masonry Chamber 60 x 60 x 75 cm inside, in brick work in cement mortar 1:4(1 cement: 4 coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) i/c necesary excavation, foundation concrete 1:5:10( 1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3( 1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay F.P.S (non modular) bricks of class designation 100 A

Providing and placing on terrace polythethylene water storage tank ISI. :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (3000x2=6000)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m: All kinds of soil Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia

Providing, laying and jointing glazed stoneware pipes class SP-1 'A' with stiff mixture of cement mortar in the proportion of 1:1(1 cement: 1 fine sand) including testing of joints etc. complete. 150mm diameter

Providing and laying cement concrete 1:5:10( 1 cement: 5 coarse sand:10 graded stone aggregate 40mm nominal size) all-round S.W pipes including bed concrete as per standard design.150mm diameter S.W pipe

Providing and fixing square mouth SW gully trap grade A complete with CI grating brick masonry chamber with water tight CI cover with frame of 300X300mm size(inside) the wt. of cover to be not less than4.50kg. And frame to not less than 2.70 kg. as/standard design 180x150mmsize p typeWith F.P.S. bricks designation 7.5

Providing and laying non -pressure NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc. 150 mm dia R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4(1 cement: 4 coarse sand) R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80cm and 45cm deep including C.I cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90x80cm With F.P.S bricks class designation 75

Constructing brick masonry chamber for underground C.I inspection chamber and bends with 75 class designation bricks in cement mortr 1:4( 1 cement: 4 coarse sand) C.I cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab ith 1:2:4 mix ( 1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) foundtion concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610mm and 45cm deep for single pipe line:With F.P.S bricks

Extra for depth beyond 45cm of brick masonry chamber: For 455x610mm size With F.P.S bricks

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with brick of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With F.P.S. bricks

Supplying materials, labour for constructing Septic Tanks of following sizes & as per sections given in the Drawings & Designs, all complete as per specifications and direction of Engineer-in-charge. [5.0 mtr (long) x 1.5 mtr (wide) x 2.25 mtr (deep) {of inside finished size as per design & drawings}]

Rain water harvesting tank (size- 6.0 X 2.0 X 2.5 M. deep + 0.50 M. free board) capacity 30000 LITS. approx & filter pit (size- 1.20 X 0.90 X 1.20 M. deep)

Providing and fixing on wall face PVC (working pressure 4kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.110 mm diameter

Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. Coupler 110 mm

Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. Single pushfit Coupler: 110 mm

Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. Single tee with door 110 x 110 x 110 mm

Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. Bend 87.50 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50 x 50 x 50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Boring/drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil. 300 mm dia

Boring/drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.100 mm nominal size dia

Gravels packing in tubewell construction in accordance with IS 4097 including providing graval fine/medium/coarse,in required grading & sizes as per actual requirement,all complete as per direction of Engineer-in charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by V notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing & fixing suitable size threaded mild steel cap or spot welded plate to the top of borewell housing/ casing pipe ,removable as per requirement,all complete for borewell of, 150 mm dia

Providing & fixing MS clamp of required dia to the top of housing/casing pipe of,removable as pe tubewell as per IS;2800(part-I), including necessary bolts & nuts of required size complete 150 mm dia

Providing & fixing suitable size threaded mild steel cap or spot welded plate to the top of borewell housing/ casing pipe ,removable as per requirement,all complete for borewell of, 100mm dia

Establishment of -3 HP of submersible pump set of approved brand and make, all complete

Boring/drilling borewell of required dia for casing/strainer pipe by suitable method prescribed in IS:2800(part-I),including collecting sample from different strata,preparing and submitting strata chart/bore log,including hire & running charges of all equipments,tools,plants and machineries required for the job ,all complete as per direction of engineer in charge,upto 90 metre depth below the ground level. All type of soil. 300 mm dia

Supplying,assembling,lowering and fixing in virtical position in borewell ,unplasticized PVC mediumnwell casing (CM) pipe of required dia, confirming to IS:12818,including required hire and labour charges,fittings and accessories etc. all complete, for all depths, as per direction of Engineer-in-charge150 mm nominal dia

Supplying,assembling,lowering and fixing in virtical position in borewell ,unplasticized PVC medium well screen (RMS) pipes with ribs , confirming to IS:12818,including required hire and labour charges,fittings and accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 150 mm nominal dia

Supplying , filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the Recharge Pit,over the existing layer boulders in the required thickness ,for all leads & lifts, . all complete as per direction of Engineer-in-charge

Providing & fixing suitable size thre platebto top of borewell housing/casing pipe,removable as per requirement all complete for borewell of 150 mm dia

Providing & fixing MS clamp of required dia to the top of housing/casing pipe of,removable as pe tubewell as per IS;2800(part-I), including necessary bolts & nuts of required size complete. 150 mm clamp

Providing & fixing Bail plug/ bottom plug of required dia to the bottom of pipe assembly as per IS;2800(part-I), 150 mm dia

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m: All kinds of soil. Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia

Providing and laying non -pressure NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc. 150 mm dia R.C.C. pipe

Extra for depth beyond 45cm of brick masonry chamber: For 455x610mm size With F.P.S bricks

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutoutsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer’s specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required-Group C (Batten Holder Point, Tube Light Point, 2'x2' LED Light Point, 1'x1' LED Light Point, Down Light Point, Call Bell Point, Wall Fan Point, Ceiling Fan Point, Exhaust Fan Point).

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (for CKT)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (For Street Light)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (For Computer + Multi Socket)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as 2 X 4 sq. mm + 1 X 4 sq. mm earth wire (For AC Point)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as 4 X 10 sq. mm + 2 X 10 sq. mm earth wire (For TPN DB)

Supplying and fixing 2 pin, 6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate/ switch box including connections but excluding modular plate etc. as required.

Supplying and fixing electronic musical call suitable for single phase, 230 volts complete bell as required.

Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 4 nos. 3 pin, 5/6 amps modular socket outlet and 4 nos. 5/6 amps modular switch, connection etc as required. ( Used for computer point )

Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 2 nos. 3 pin, 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc as required. ( Used for Multi point )

Supplying and fixing modular type 25 amps A.C. unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc as required.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required. 3 watt LED Lamp

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. directly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing recess/surface mounted 23/24 (1ft X 1ft) watt LED downlighter complete with integrated electronic driver & LED directly on ceiling/false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing Surface mounted 15/18 watt LED downlighter complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated copper conductor etc as required.

Supply and installation of 300 mm, 230 v A.C. exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.

Supply and installation of 400 mm, 230 v A.C. wall/cabin fan including fixing the bracket, making connection, testing, commissioning etc as required.

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way ( 4 + 12 ), double door, horizontal type

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way ( 4 + 18 ), double door, horizontal type

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6/32 amps, Single pole

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps, Tripole pole and neutral

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 50/63 amps, Tripole pole and neutral

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

SITC of Following size of ’G’ frame Loadbank Panel Board System is a power distribution board with MCCBs as incoming and outgoing switching-cum-protective devices, for distribution of power to various loads as per the requirements of the system.The modular construction of load bank renders the customary panel building redundant by virtue of compactness, reduced cost and short delivery time coupled with reliability of the various modular units. All units are fabricated using sheet steel of 1.6mm and are epoxy powder coated to give a superior finish.8 way, 400A

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required. 25/100 Amp, 16 KA

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required. 400 Amp, 35 KA

S/F of Double door Cable Alley I/C 400 A/630 A,O/G 4P GF 8Way

S/F of Meter Module - Digital

S/F of Terminal for G Frame Outgoing (Per Pole)

S/F of Spreader Terminal 200 A~400 A

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed armoured electrical cable with aluminium conductor for working voltage upto 1.1 KV etc as required. 185 sq. mm., 3.5 core

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 185 sq. mm and upto 400 sq. mm

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Supplying and fixing 90 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as 40 mm dia

Supplying and fixing wall/floor mounted cubical panel board, fabricated with 16 gauge iron sheet, suitable for panel mounted switch disconnector, including bus-bar chamber, insulator and painting etc. as required. (but without busbar copper strip)

S/F copper Strip 50 mm X 5 mm sizes for bus-bar including interconnection etc. as reqd.

Supply of Pilot lamp for indicator

Supply and fixing digital voltmeter, three phase in the existing cubical panel board including drilling holes in the panel board, making connection etc as required.

Supply and fixing digital Ammeter, three phase in the existing cubical panel board including drilling holes in the panel board, making connection etc as required.

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.400 Amp, 35 KA

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required. 630 Amp, 35/50 KA

Providing and fixing following capacity four pole ON-load/ panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required. 400 Amp, four pole

GI BOX With Modular Cover Plate Make-Legrand Description - Supplying and Fixing 75mmx75mm modules, GI box along with modular base & cover plate for modular fitting in recess etc as required.

2 Mtr Long Factory Made Cat6U RJ45 Patch Cord Make - D-Link/ Molex Description - Supply of 2 Mtr. long factory made CAT 6U/UTP RJ45 patch cord

1 Mtr Long Factory Made Cat6U RJ45 Patch Cord Make - D-Link/ Molex Description - Supply of 1 Mtr. long factory made CAT 6U/UTP RJ45 patch cord

6U Network Rack Make - Legrand Description - Supplying Fitting fixing 6U Rack, Glass 4mm Toughened Tinted Glass Door, Accessories : Cooling Fan - 2 nos, PDU 230Vac - 1 no, Cable Manager Metal - 1 no complete etc as required.

12U Network Rack Make - Legrand Description - Supplying Fitting fixing 9U Rack, Glass 4mm Toughened Tinted Glass Door, Accessories : Cooling Fan - 2 nos, PDU 230Vac - 1 no, Cable Manager Metal - 1 no complete etc as required.

Cat6 U/UTP 24 Port 19" Modular Type Paech Panel Make - Legrand/ D-Link Description - Supplying Fitting fixing Cat6 U/UTP 24 Port 19" Modular Type Paech Panel Loded with 24x Toolless RJ 45 which is 6 in a block complete etc as required.

24 Port Ethernet Giga Unmanaged Switch Without fiber Module Along with AC Power Supply Make - D-Link Description - Supply installation testing & commissioning of Ethernet Unmanaged Switch Without fiber Module Along with AC Power Supply: 24x10/100/1000 Bas

Ethernet Managed Switch Without fiber Module Along with AC Power Supply Make - Legrand Description - Supply installation testing & commissioning of Ethernet Managed Switch Without fiber Module Along with AC Power Supply: 24x10/100/1000 Base T LAN switch

Cat-6 PVC Insulated and sheathed LAN Cable Make - D-Link Description - Supplying and drawing UTP 4 Pair Cat-6 PVC Insulated and sheathed LAN Cable through existing PVC concuit including connection , testing etc required.

RJ 45 io Outlet Socket Make - Legrand Description - Supplying and fixing of tooless RJ 45 information for CAT 6 U/UTP white colour Arteor Modules 1 along with built in crimping handfree min 5 times reconnection possible and shutter protection etc as r

Wiring Charges

Installation Per Point, Testing & Commissioning Charges

SITC of Single Loop Fire Panel ( Make - Honeywell/ Bosch/ Eqv. )

SITC of Addressable Smoke Detector with Base ( Make - Honeywell/ Bosch/ Eqv. )

SITC of Addressable Manual Call Point ( Make - Honeywell/ Bosch/ Eqv. )

SITC of Addressable Sounder with Base ( Make - Honeywell/ Bosch/ Eqv. )

SITC of Addressable Heat Detector with Base ( Make - Honeywell/ Bosch/ Eqv. )

Supply of Mounting Accessories like back box for detectors, devices & cable glands, etc.

Supply & Laying of 25 mm dia. PVC Conduit for laying flexible cables, Wiring & Installation Charges

Supply & Laying of 2C x 1.5 Sq.mm PVC insulated copper conductor un-armoured cable

Photovoltaic Power Plant conforming to MNRE specification as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- (a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, Conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2, Solar Photovoltaic Module conversion efficiency shall not be less than 16.5% PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. (b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. (c) Data Monitoring System complete with accessories. (d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. (e) Lightning and surge voltage protection. (f) Connections and interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kv grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

SITC of Split type wall mounted Air Conditioning unit of 1.5 TR, 5 star capacity including indoor, outdoor unit fitted with inverter based rotary compressor, 100 Percent copper condensor and first charge refrigerant R410A/ECO friendly gas only. The condensing unit working range should be capable for providing cooling between +/- 5 deg. C to 50 deg.C having minimum cooling capacity 18000 BTU/h or 4500 Kcl/h and airflow should have minimum 400 CFM/h/TR (600 CFM/h for 1.5 TR) along with 3 mtr. copper pipe with insulation, cordless remote control, auto air swing louvers, condensed water oulet pipe 2 meter complete etc as reqd. Outdoor/Indoor units should be of same make.

SITC of Atomatic Voltage Stabilizer of Capacity 4 KVA, input voltage -130V± 10% and output-220 V ± 10%. Make - V- Guard/Microteck of Capacity & input Range 130V to 280V Model (For 1.5 Ton AC)

Supply, Installation, testing andcommissioning including vaccumiazation and Nitrogen testing offollowing nominal sizes of soft/hard drawn copper refrigerant piping complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class- O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 6.4 mm dia (ID) Soft drawnCopper Tubes with tube thickness of 0.8 mm and with 13 mm thick Nitrile tubular insulation (For 1.5 TR Split AC)

Supply, Installation, testing andcommissioning including vaccumiazation and Nitrogen testing offollowing nominal sizes of soft/hard drawn copper refrigerant piping complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class- O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 12.7 mm dia (ID) Soft drawnCopper Tubes with tube thickness of 0.8 mm and with 13 mm thick Nitrile tubular insulation (For 1.5 TR Split AC)

S/F of hard round PVC drain piping suitable of 1.5/2.0 TR Split A.C Machine

S/F of 20/24" ready made M.S. prepainted wall Satnd structure Suitable for 1.5/2.0 TR Split AC Machine including all accessories.

Supply & Topup of R-410/32A Refrierant to make up additional copper pipes length of 1.5/2.0 TR Split AC Machine (250 gram per machine)

Supply and fixing of size 100mm x 100mm x 100 mm PVC tray with cover for covering of insulated copper pipes.

Carriage of materials

Stone Chips (1 km katcha+175 km pucca)

Coarse Sand (1 km katcha+49 km pucca)

Bricks (1 km katcha+7 km pucca)

Local Sand (1 km katcha+2 km pucca)

Extra cost of materials

Bricks

Cement

Rate are inclusive of GST @ 18% for the above items

Name of the Contractor

Address of the Contractor

I/we offer in Figures……. in words………………… % (Percentage) High / Less/Estimated rate as mentioned in the Bill of quantity.

In word

Seigniorage fee

Dismantling of old Division office building & IB including foundation in all respects in the premises of 132/33 KV GSS Hajipur in the premises of 132/33 KV GSS Hajipur

Note :The rate for seigniorage fee calculation shall be firm and shall not be affacted by the percentage rate (Below/ Above) quoted for BOQ. (ii) Rate for dismantling work of the building shall be firm and shall not be affacted by the percentage rate (Below/ Above) quoted for BOQ. (iii)The dismantled material shall be the property of the agency and the dismantled materials shall be removed from GSS campus (Minimum 03 km away from GSS).

Partition & Furniture of office building

Full height Double skin partially glazed partition Providing and fixing double skin partly glazed full height double skin partitions with frames of 50mm x 38mm(finished size) seasoned hardwood members (malaysian salwood / hollock) at max. intervals of 450mm x 450mm with provision of bigger members at skirting, top of partition / top of panelled partition / fixing to false ceiling, fixing to RCC slab, beams etc, fixing to door frames, (door choukhats shall be 1st Class TEAK WOOD ) etc, all woodwork to be treated with 1st quality anti-termite paint, and covered with 6mm thick BOILING WATER PROOF grade plywood and 1.0mm thick laminate of approved colour, texture and design, as per standard with grooves / small panels cut and pasted in the same as per design, on both sides so as to form a double skin partition, to level 900mm and with 12.0mm edge polished mm clear float glass above, Fixed in wooden frame and with wooden beading as per detail design, which is to be of 1st quality teakwood (All visible wood to be of 1st quality "teakwood") and shall be polished. The wooden frame of the partition shall continue right upto the ceiling, if required, and shall be firmly fixed to the ceiling (and ground) by means of RAWL PLUGS, so as to form a stable system. If the same does not go up to the ceiling, extra supports shall be given to make it a stable system. Doors shall have separate choukhats of 100mm x 60mm of Salwood, covered with Teak Ply, and frames of teakwood which shall be of 150mm x 40mm at the top and sides, and 200mm x 40mm at the bottom. Beading shall be given as / design + specs. Door panel shall be of 12mm thick clear glass. All necessary hardware such as stainless steel tower bolts, ISI marked door closers OR floor springs, 6 Lever Godrej Mortice Locks, and any other hardware required for the door shall be included in the price. Any extra members required for Stability of the Partition / Aesthetic value shall be provided without any extra payment for the same. The Wooden Frame and all wooden members / elements shall be coated with anti-termite paint (Chloropyrophos) , as per the Manufacturers Specifications.

Door Accessories Specifications

Door Handle

Providing and fixing bright finished brass handles with screws etc. complete:

Door Latch

Providing and fixing bright finished brass door latch with necessary screws etc. complete :

Floor Stopper

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Door Closer

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Note: Payment for doors shall be included in this item / relevant partition item.

Openings for communication / conversation if required shall be provided as required as per detailed design and nothing extra shall be paid / deducted for the same.

The height of the partition shall be measured upto the bottom of the false ceiling, and if the false ceiling is at two different levels, it shall be measured upto the height of the higher false ceiling, and if there is a false ceiling on 1 side and R.C.C slab without false ceiling, it shall be measurd upto the R.C.C slab in this case. The area above the false ceiling shall not have any ply / laminate / etc., but only the frame shall be continued.

All electrical wires, accessories, telephone wires, etc, shall be run in the partition as per Electrical Drawings and designs, and the same shall be paid under the Electrical Works to the Electrical Contractor. Nothing extra shall be paid for the co-ordination of the same, or for any minor changes etc. to the Interior Contractor.

All items necessary for completing the above mentioned work are deemed to be included in the scope of work, whether or not they are specifically mentioned in the B.O.Q / tender documents / drawings.

All exposed wooden surfaces are to be polished, and all exposed wooden surfaces shall be of teakwood.

Full height Double skin fully panelled partition -Providing and fixing Fully paneled partitions as per specifications given in Item No. 1 above, except that no glazing shall be there in the partition (doors shall however be glazed, if so desired by the or can be fully panelled also, with the same details and specifications in Item No. 12 ) all complete as per designs, details and specifications.

High Back Chair - Chair Size (L) 600mm X (D) 660mm X (H) 1,275mm. Nylon base chair with push back mechanism & Fix handle. Back & seat cover cushion chair uphlostered in fabric. Syncro mechenism with locking system and five star chrome base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Visitor Chair - Chair Size (W)595mm X (D)510mm X (H)875mm. Multi purpose fixed chair,Metal frame,PU Padding on armrest. Cushion upholstery in leatherette with four leg metal legs with matt finish. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Office Table with Side Unit Return - Table Top Size (W)2000mm X (D)1800mm X (H)755mm with Side Unit. The Table made of PLPB with matt finish. Made with a combination of engineered wood, this gorgeous desk has contrasting panels in black for a contemporary look. Coupled with a runner and storage for your files and cabinets, the DWS/0200 is a desk meant for the discerning tycoon. With a warm walnut finish, the dual tone finish of the desk adds to its overall style and finish. With an option of regular drawers and shuttered glass storage units you can take a pick of which unit suits you the best. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Revolving Chair- Chair Size (W)660mm X (D)500mm X (H)1265mm. Made From High-Density Foam, The Sink-In Cushions And The Cradling Backrest Provides Contouring Comfort For All-Day Seating. The Soft To Touch Premium Leatherette Upholstery Add Elegance To Its Look While Also Making It Stain & Fade Resistant. Features Such As Synchro Multi-Locking Mechanism, Pneumatic Height Adjustment, Tilt Tension Control, Etc, Let You Find Your Ergonomic Position With Ease. The Pneumatic Height Adjustment Along With The Thick Padded Headrest And Armrest Further Let You Sit In Absolute Comfort. A Strong Chrome Base Supports The Structure While The 360 Swivel And 55Mm Castors. The Product Should be Certified Company BIFMA,ISO 50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Visitor Chair - Visitor Chair Size (W)590mm X (D)490mm X (H)980mm. Its moulded seat and indented back provide exceptional all-day support. Premium virgin foam sits atop a 14mm thick boiling waterproof plywood forming the moulded seat. This is then encased in deep black fabric upholstery with defined line seams that provide comfortable seating while adding depth to the high backrest. The powder-coated metal cantilever base provides extraordinary support for easy seating. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Mid Back Chair- (Back Height-495xBack Width-470)mm & (Seat Depth 485xSeat Width-475)mm with Min-Max Height (410-470)mm. Nylon base chair with push back mechanism & Fix handle. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star Nylon base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC. Color-Black

Mid Back Chair- (Back Height-495xBack Width-470)mm & (Seat Depth 485xSeat Width-475)mm with Min-Max Height (410-470)mm. Nylon base chair with push back mechanism & Fix handle. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star Nylon base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC. Color-Black

Medium Back Chair - Chair Size (L) 610mm X (D) 660mm X (H) 1130mm. This High-Performing Chair Invariably Works To Put You At Ease. The Novel S Curve Of The Backrest Ensures That The Natural Curve Of The Spine Is Maintained While The Adjustable Leaf Lumbar Support With C-Curve Provides Extra Comfort And Support To The Lower Back. Adorned With A Ventilated Body Fabric, It Keeps You Calm Even On The Most Stressful Days. The Synchro Single Locking Mechanism And Tilt Tension Control Further Work To Provide An Ultimate Ergonomic Experience. The Solid Nylon Base Provides Extraordinary Support While The 55Mm Castors Help In An Easy Smooth Movement. Smart And High-Performing. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.