Quatation 02/2023-24/DR

Amount

Supply, Installing, Testing & Commissioning of IP PTZ Camera, 1/2.8” 2MP CMOS Image sensor (0.9071 centimeters), Max. 25/30fps@1080P, Powerful 25x Optical and 16x Digital zoom WDR (120dB), 3D-DNR, Day/Night (ICR), ROI, Defog, AWB, BLC, HLC, Support Starlight Function, Up to 300 presets, auto scan, 8 tour, 5 pattern, auto pan, IR Range of 100 Mtr., Max 240°/s pan speed, 360° endless pan rotation, Built-in 2/1 alarm in/out, IP66, Support PoE, Mobile Software: iCMOB, gCMOB, CMS Software: KVMS Pro. with 3 years FCAMC.

Supplying, Erecting Commisioning of 2Megapixel Bullet Camera with Motorised lens(1920x1080) Resolution, Sopport ROI function, Standard Video Compression Ratio, Progressive scan Cmos, Capture motion video withoutt incised margin, 2.8 ~ 12mm (4.3x) varifocal lens, Min. Illumination :Color : 0.095Lux (30IRE), B/W : 0Lux (IR LED on), Angular Field of View: H : 109.7˚ ~ 26.0˚ / V : 60.8˚ ~ 15.2˚ / D : 131.3˚ ~ 30.1˚Max 20 FPS @4M,Max. 30 Fps@2M, H.265. H.264, MJPG/ Multiple streaming, Micro SD(128GB), Memory slot, POE/ 12Vdc, IR viewable lenght 30 m, IP-66, IK-10, Hallview support, LDC support ( Lens Distortion Correction)

64 ch Network Video Recorder, Supplying, erecting, testing and commissioning of Connect Up to 64 tp Cameras, Dual OS, Up to 12 Megapixel5 Resolution, Two independent HDMt & Two VGA outputs, Atleast one H0Mt output of 4K resolution, atleast 1 VGA output with output upto 1920 x 1080, support H.265, MJpEG, supports N+1 hot spare system,supports RAtD0, RAtD1, RAtD5, RAtD6 and RAtDlO ,Supports HDD hot swap, SupporB Oual power-Redundant, tncoming Bandwidth 320 Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 8TB, 3 x USB at least 1 x USB with 3.0, Alarm t/O 1614, RS-485, RS-232, 2 R]-4S 10 /100/1000 Mbps self-adaptive Etherner interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified.

Supply, installation, Testing & commissioning of IP base PTZ Controller with required software, license & accessories as specified in Specification.

Supply and installation of 8TB surveillance storage Hard Disk Drive-24r/ Surveillance HDO capacity -8 TB interface- SATA lll 6 Gb/s Max sustained Transfer Rate OD- 210 MB/s cache- 256 MB Tamish Resistant load /unloadcycles- 300 000 power on Hours/ year 8760 mean Tim Between failures (MTBF) - I miliion hours operatingTemperature- Ambient: 4'l F/5 C(min) Drive case : '158 F/70C (max) Non operating Temperature Ambient:40 F/{0C (min).

Supply Installation Testing & commissioning of Client PC Hardware with a minimum speicification of Intel i7 Quad Core Processor 7th Generation at mim 3.6 GHz ,12M, Intel HD Graphic 630, 6.4GT/s, 4x4 GB or more of RAM, 500GB SATA,10K RPM 3.0Gb/s Hard Drive for OS and VMS Applications Network Interface Card - 10/100/1000 MB Network Fiber Interface Card - 4 x 1Gbps in fault tolerance configuration Video Card – nVidia 2 x NVS295 Quad Monitor Graphics card to support 4 multiplexed Monitors Motherboard should support Intel as well nVidia GPU in active-active mode and both devices should be enabled. DVD-R/W Microsoft® Windows® 8.1 / 10 Pro or Higher 64 bit

Supply Installation Testing & commissioning of 21" colour ,Flat Screen type Professional CCTV Surveillance HD monitor for above client workstation

Supply, Installing, Testing & Commissioning of Monitor LED,42 inches or higher, Full HD l. Size : 42 inches 2. Resolution : Full HD 3. Backlight : LED 4. Brightness : 400 NITS min. 5. Contrast : 1200 :1 or better 6. Power supply: 230v + or - l0%, 50 Hz

Supply, installation, Testing and Commissioning of 5 Meter GI powder coated poles for mouting of 2Nos. Of camera on each poles with necessary accessories incluiding require foundation for the same with IP66 rated outdoor housing for power supply point & media convertor.

Supply, INstallation, Testing and Commissioning of Wireless Keyboard and Mouse with required patch cables and accessories.

Supply, Installation, Testing & Commissioning of Cantileaver tray for 42U Rack

Supplying, erecting heavy duty sliding tray with Telescopic chanel made from 1.5mm thick powder coated CRCA sheet stell

Supply & Errecting 1U PVC Cable Manager suitable to install on all Sizes of Networking Rack

Loudspeaker: Full-range loudspeaker designed for sound reinforcement and foreground music; for both indoor applications with frequency range of 52 Hz - 15 kHz; Continuous power: 240W @ 8 Ohms; Nominal dispersion of 120H X 100V; Sensitivity of 92 dB; Max SPL of 116 dB; 8 x Bose 4.5” (114 mm) full-range cone transducers; Powder coated steel grille, Weather Rated Design with standard mouting accessories & hardware.

Stage Monitor: Multi-position Floor monitors with 6 X 2.25" Mid-high drivers and 2 X 5.25" woofer gives articulated array configuration 120 X 60 degrees coverage; Frequency respose of 70Hz-16kHz; Sensitivity 90 db SPL; Max SPL 113 db SPL; power handling of 200W @ 8 Ohm, Internal pAssive crossover network does not require active equalization; Rear bumper prevents unwanted movement; drivers enclosed in Molded textured polyethylene material with powder coated steel grille.

Subwoofer: Single 12" Subwoofer with AcoustimAss speaker technology, low frequency sound is launched on two air mAsses, acoustically filtering out audible distortion; frequency response of 50Hz to 140Hz; Power handling of 450W @ 8 Ohm; Sensitivity of 90 dB SPL; Max SPL of 116 db SPL enclosed in Vinyl-wrapped, high density wood composite.

Supply , installation , testing and commissioning of Volume control for Green Room - Analog with back box

Ceiling mount speaker with frequency respose of 95Hz - 17kHz; nominal dispersion of 140 degree conical; Power handling 16W @ 8 Ohms, Transformer tapping (70/100V) : 1W, 2W, 4W, 8W, 16W), sensitivity 84 db SPL; and Max SPL of 96 db SPL with powder coated steel grille.

Amplifier: ClAss D Zone amplifier with power As 1 X 90 W @ 70/100V; frequency response of 60Hz to 20kHz; THD <1%; I unbalanced AUX input, 1 balanced page input, I balanced mic/line input, 2 unbalanced line; Dynamic range is of 88 dB; built in loudspaker EQ.

Supply, Installation, testing and commissioning of wall mount control room loudspeakers with 4.5" driver or better. frequency range of 75Hz to 19kHz; long term power handling of 40 Watt; Nominal dispersion of 120 H X 90 V; Sensitivity of 87 db SPL and Max continous SPL of 102 db SPL; Nominal Impedence 8 Ohms; Transformer tappings @ 100 V: 10 W, 20W, 40W per the tender speciifcations.

Amplifier: Digital ClAss D Amplifier 4000W (500 W X 8 channels @4 ohm); THD < 0.4%; damping factor > 1000; inbuilt programmable and monitorable DSP like compressor, limiter, gates etc with complete equilisations.

Processor: 2x4 Signal Processor with 2 analog balanced differential input; 4 analog balanced differential output with programable custom pages like seminar / presentations / cultutal events / conferences etc As per site requirements ; custom channel routing; crossovers, limiters, gain control; band pAss filters; delays; limiters;gain and signal polarity.

Supply, Installation, Testing & Commissioning of 16-Channel Mixing Console: Max. 16 Mic / 16 Line Inputs / 4 GROUP Buses + 1 Stereo Bus / 4 AUX,D-PRE” mic preamps with an inverted Darlington circuit, 1-Knob compressors, High-grade effects: SPX with 24 programs, 24-bit/192kHz 2in/2out USB Audio functions, Works with the iPad (2 or later) through the Apple iPad Camera Connection Kit / Lightning to USB Camera Adapter, Includes Cubase AI DAW software download version, PAD switch on mono inputs, 48V phantom power, XLR balanced outputs, Internal universal power supply for world-wide use, Rack Mount Kit Included, Metal chassis and incluiding all standard accessories as complete.

Supply, Installation, testing & commissioning of Gooseneck microphone with table top stand with ON/OFF Switch; Gooseneck Length : 15" or better; Polar Pattern : Cardioid / hypercardioid / supercardioid; S/N Ratio : 65 dB or better; Max SPL for 1% THD : 107 dB or better; Freq Response : 50 Hz to 17kHz or better; LED Indication : Yes; RFI Sheilding : Yes; complete with all standard accessories As per the tender specification.

Supply, Installation, testing & commissioning of Shotgun Microphone with Type of transducer : Condenser; Polar Pattern : Cardioid / hypercardioid / supercardioid/ Lobe Pattern; Freq Response : 40Hz to 19kHz or better; Sensitivity : 21.1mV/Pa or better complete with all standard accessories As per the tender specification.

Supply, Installation, testing & commissioning of Wired handheld microphone with Type of transducer : Dynamic; Polar Pattern : Cardioid / hypercardioid / supercardioid; Freq Response : 50Hz to 15kHz or better; Sensitivity : 1.85mV or better complete with all standard accessories As per the tender specification.

Supply, Installation, testing and commissioning of Wireless handheld microphone with Polar Pattern : Cardioid / Hypercardioid / Supercardioid; RF Freq Range : 516 MHz to 865 MHz or better; Audio Bandwidth : 80 Hz to 15kHz or better; RF Power : 20mW or better; THD : <0.9% or better; S/N Ratio : >105 dB or better; As per the tender specications.

Supply, Installation, testing and commissioning of Wireless Lapel microphone with Polar Pattern : Cardioid / Hypercardioid / Supercardioid; RF Freq Range : 516 MHz to 865 MHz or better; Audio Bandwidth : 80 Hz to 15kHz or better; RF Power : 20mW or better; THD : <0.9% or better; S/N Ratio : >105 dB or better; As per the tender specications.

Supply , installation , testing and commissioning of The Drum Sets offer high-performance drum microphones from the Touring Gear series. Set of Minimum 7 microphones, 1 x bAss Drum, Dynamic cardiod, 4 x Snare Drum Dynamic Supercardiod, 2 x Overhead microphons with close Drums, Cardiod, pattern. To be supplied with Soft carrying cAse.

Supply , installation , testing and commissioning of Antenna Splitter and combiner for above microphones

Supply , installation , testing and commissioning of Coax cable for antenna & required connectors

Supply of Light cations.weight tripod alluminium Microphone stand with Long Arm, boom type & chrome plating with standard mouting accessories As completed

Supply of Light weight tripod alluminium Microphone stand with short Arm, boom type & chrome plating As per the tender specifications.

Supply , installation , testing and commissioning of 3- pin, Single XLR-female table mount plate, Connector should be neutrick only.

Supply and fixing of 3 point XLR mic wall mount junction boxes with one Speakon Connector As per the tender specifications.

Supply and fixing of 1 point XLR mic junction boxes with one Speakon Connector As per the tender specifications.

Supply and installation of CD player with USB As per the tender specifications.

Supply and laying of 2 core 2.5 sq mm PVC insulated Cu conduction loudspeaker cable As per the tender specifications.

Supply and laying of 2 core PVC insulated Cu conduction sheilded microphone cable As per the tender specifications.

Supply of UL Listed Connectors As per the tender specifications.

Supply , installation , testing and commissioning of Multipurpose Controller Combining leading edge and signal dimming control system for Audience seating area only, Minimum 4 x 10A Leading Edge Dimmer, Minimum 4 x 10A Relay, Minimum 4 x 1-10V / DSI / DALI - Total load 40A, Overload Protection 4 x 10 A 6 kA single pole thermal magnetic circuit breakers, Regulating Device Triac - 40 A nom., 600 V, 400 A surge Switching Device Relay 16 A nom., 165 A surge, Control Inputs/Outputs One RS-485 DyNet / DMX512 serial port One programmable dry contact AUX input, Presets 100 nos with standard software & required accessories

Supply , installation , testing and commissioning of 8 Channel Snake cable for audio.

Supply, termination, testing & commissioning of XLR neutrik Connector

Supply , installation , testing and commissioning of 8 port XLR patch panel to be mounted on Rear wall of Stage at Skirting level, All should be with Neutrick connectors only.

Supply , installation , testing and commissioning of AV Connectors including XLR , VGA, HDMI, Display Port (XLR / Speakon connectors should be of Neutrik / Amphenol only)

Supply,fixing 8 pn or 3 pin XLR connector male or female with soldering/crimping for Lighting Control

Supply Fixing DMX Socket 1x14 way with m.s. junction box.

Supply Fixing DMX Splitar 1x16 way .

Supply,fixing Stage CONSOL Pilot 2000.For LED lights. Console shall have Universal DMX512 controller able to control up to 40 units , Each unit with maximum of 36 channels.total of 512 DMX channel, Able to controller dimmer pack with maximum of 192 channels, 40 programs or chases, mchases, presets. each program (chase.mchase,preset)up to 40 steps, Able to use 4 programs. 4 chases.4mchase.4 presets at same time , Internal unit library,able to create new unit library in controller, Able to backup or update data to/from PC with RS232 , Midi input/midi output , Internal mic or sound input, DMX, stand-alone, master/slave, sound activated mode, DMX recorder and edit function integrated, 3-pin or 5-Pin XLR serial input/output, Dual bracket system available for setting the fixture on the ground or hanging, Electronic ballast and power supply and Overheat protection. incluiding required software, hardware and standard patch cable and accessories

Supply,fixing Stage Light Fitting As Follow -LED PAR stage 54X3w RGBW DMX with connecting 1 mtr cord and XLR Connector 2 nos

Moving Head DMX 575 Sharpy with connecting 1 mtr cord and XLR Connector 2 nos

LED Flood 120W DMX with connecting 1 mtr cord and XLR Connector 2 nos

LED FrAsnel spot lights 220W DMX [solar] with connect 1 mtr cord and XLR Connector 2 nos

Supply,laying in XLR control cable in existing conduit for connections to consol.

PATCH Panel: Supply,erection of floor mounting stand fabricated in two sections made of iron 35x35x5 mm. angles, closed from all 3 sides with removable covers and bottom cover made out of 18 swg CRCA sheet , hinged doors in two parts,panel locks, and arrangement to keep alu.rack on the top and a bakelite sheet 10 mm thick with 10 mm dia 90 Nos of holes for wires entry, earthing studs,painted/ powder coated and G.I. Hardware and 12 Nos toggle switch, 22 Nos backelite 16 A/6 A socket mounted on m.s.plate. required.

DIMMER PANEL: Supply,erection of dimmer power pack of (6 channels each x 2) 12 channels 2 kW/channel with 2 Nos 6/16 A Sockets/ channel, indicating lights, 40 A 4 pole MCB for incomming supply, 10 A SPMCB for outgoing supply fuse,cooling fan,and all mounted on alluminium rack , all sides closed with

MIC BARS: Providing & Fixing of Mic Cars in G.I. pipe 400mm dia 'B' clAss length 40"

LIGHT BARS : Providing & Fixing of Light bars in 40 mm G.I. Pipe (Dual Barrel) 'B' ClAss with Brackets. M.S. Tray for Electric wire.( Size 100mm X 50mm )

Supplying and erecting LED circular 24-28 W downlighter with Dali Dimable balast diming from 0% to 100% and 90deg 4000- 2800K,90-300V having pressure die-cast aluminimum housing with white front frame with opal translucent cover with provision for spring loaded mounting clips complete.

Supplying and erecting LED circular 14-20 W downlighter with Dali Dimable balast diming from 0% to 100% and 90deg 4000- 2800K, 90-300V having pressure die-cast aluminimum housing with white front frame with opal translucent cover with provision for spring loaded mounting clips complete.

Recess mounted aesthetically designed 10-15W LED spot light for low celing height applications. Spot light shall have Input Voltage : AC 220-240V, 50/60Hz, Driver Type : Constant Current. Non-Integral P.F >=0.5, Voltage Operating Range : 100-300 VAC, High Surge Protection, LED Life : 30,000 BH, Optics : PMMA lens for better light distribution Accessories : With Driver including required accessories.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Supplying and erecting rigid PVC conduit 40/50mm dia with PVC acessories on wall/ ceiling as per sp.no. WG-MA/CON para 1.1.1 for drain pipe complete with having 9mm thickness elastomeric nitrile rubber/ foam tube type sleeves insulation.

Supplying and erecting rigid PVC conduit 32mm dia. with PVC accessories on wall /ceiling for Drain Pipe complete with Elastomeric Nitrile rubber / foam tube type sleeves

Supplying and erecting rigid PVC conduit 25mm dia. with PVC accessories on wall /ceiling for Drain Pipe complete with Elastomeric Nitrile rubber / foam tube type sleeves

Supply, Installation, testing & commissioning of Air Cooled Screw Chiller multiple Semi Hermetic Screw Compressor, Shell & Tube Condensor & Chiller Expansion Valves, First Charge of Gas R134a / R 410A & Oil etc. The plant should be suitable for the following parameter Capacity. Actual Capacity at Chandrapur Ambient Conditions. The Chillers should be installed on a baseframe along with Antivibration Spring mounted pads. Detailed Specifications as per tender Documents. The Chillers shall be made available for Factory Testing as per AHRI standards on AHRI certified Test Bed for multiple point testing. Actual Capacity 160 TR. Chilled Water Inlet Temperature = 12 Deg.C Chilled Water Outlet Temperature = 7 Deg.C Air Temperature over Condenser = 43 Deg.C. Evaporator Fouling Factor: 0.0001 FPS. C.O.P.: Not less than 3.52 @ AHRI Conditions. IPLV: Not more than 0.58 @ AHRI Conditions. The equipment shall be complete with electrical panel and microprocessor control, with the following specs. a. Single Phasing Prevention. b. Under / Over Voltage Protection. c. Phase Reversal protection. d. Independent Set Points for each refrigeration ckts. e. HP / LP Trip signal interlocking. f. Interlocking for Chilled water Flow Switch. g. Auto / Manual / Test Mode facility. h. Runtime equilization for multiple compressors. i. Password access for authorised handling. j. PT-100 RTD sensor for chilled water. k. Electronic Expansion Valve.(The scope shall include loading,unloading,requried crane charges which will safetly installed chiller at terrace level safely)

Supply Installation Testing & Commissioning of Secondary Chilled Water Pump skid with end suction pump sets (3W + 1S), each capable of delivering 480 USGPM of water at 50 m head. The pump skid should be supplied with Butterfly Valves, CheckValve and Y Strainerwith requried Header Size Wheather proof Pressure & Temprature gauges. The pump should be supplied with Bronze impeller & mechanical seal with VFD. Pumps shoud be mounted on C section base frame with antivibration mounts in between Vibration isolators at inlet & outlet of each pumps.The skid shall be completely painted with Zinc Chromate Primer & Epoxy Paint. The Skid should be suitably insulated with Closed cell Nitrile Rubber of 25 mm thickness with Chemically Treated Woven Fibre Glass Covering. Only pre assembeled skids, no site fabrication is allowed. Motors shall be of IE3 GRADE. The pump motor shall be suitable for 415 + 10% volts, 50 cycles, 3 phase power supply.

Supply Installation Testing & Commissioning of Secondary Chilled Water Pump skid with end suction pump sets (3W + 1S), each capable of delivering 480 USGPM of water at 15 m head. The pump skid should be supplied with Butterfly Valves, CheckValve and Y Strainerwith requried Header Size Wheather proof Pressure & Temprature gauges. The pump should be supplied with Bronze impeller & mechanical seal . Pumps shoud be mounted on C section base frame with antivibration mounts in between Vibration isolators at inlet & outlet of each pumps.The skid shall be completely painted with Zinc Chromate Primer & Epoxy Paint. The Skid should be suitably insulated with Closed cell Nitrile Rubber of 25 mm thickness with Chemically Treated Woven Fibre Glass Covering. Only pre assembeled skids, no site fabrication is allowed. Motors shall be of IE3 GRADE. The pump motor shall be suitable for 415 + 10% volts, 50 cycles, 3 phase power supply.

Supply, Installation, Testing & Comssioing of Closed Expansion Tank will be of M.S. construction with interchangeable EPDM-BUTYL rubber membrane. The expansion tank shall be complete with safety relief valve and pressure gauge. The tank will be of pressure rating to suit the system pressure and will be sized to adequately compensate for water expansion due to operating temperature variations. The tank shall be fabricated as per IS 2825-1969 for “non-fired pressure vessels” and the flanges shall be as per IS 6392-1971. For chilled water application, it will be insulated with Closed Cell Nitrile Rubber Insulation with Chemically Treated Woven Glass Fibre Covering as per requirement. Inlet & Outlet Size 150 mm dia.

Supply, Installation, Testing, Commissioning of Pressurization Unit shall consist of two Nos. (1 working + 1 stand-by) high pressure pumps of suitable pressure rating mounted on M.S. frame, complete with interconnecting piping, isolation valves, NRV, Y-strainer, pressure gauge, pressure transmitter, auto-logic panel (IP55) with dry-run protection, electrical MCB and interconnecting wiring. The unit shall be housed in powder-painted canopy suitable for external installation, if required. Flow: 2 CMH, Head: 25 m Water Column.

Supply, installation, testing & Commissioning of 250 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation with Chemically Treated Woven Glass Fibre Covering of 25 mm thickness for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 200 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation with Chemically Treated Woven Glass Fibre Covering of 25 mm thickness for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 150 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation with Chemically Treated Woven Glass Fibre Covering of 25 mm thickness for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 125 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation with Chemically Treated Woven Glass Fibre Covering of 25 mm thickness for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 100 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 80 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 65 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation of thickness 25 mm with Chemically Treated Woven Glass Fibre Covering for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 50 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation of thickness 25 mm with Chemically Treated Woven Glass Fibre Covering for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 40 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for pipes up to 250 mm.

Supply, installation, testing & Commissioning of 32 mm dia. M. S. Class 'C' CHILLED WATER PIPING with all structural supports alomg with pipe rack required with insulation of Closed Cell Nitrile Rubber Insulation of thickness 25 mm with Chemically Treated Woven Glass Fibre Covering for pipes up to 250 mm.

Supply, Fixing & Commissioning of Temperature Guages with Murcury in Glass Stem Type.

Supply, Installation, Testing & Commissioning of Floor Mounted Double Skin Air Handling Units made out of Alu. Extruded Profile with Thermal Break Profile. The AHU panels fabricated out of 0.6 mm thick Pre-Coated G.I. Sheet with 43 mm / 47 mm PUF Insulated Panel. Blower Section shall consists of statically & dynamically balanced Forward Curved Blower capable of delivering 25000 CFM of air quantity at 60 mm total static pressure. The cooling coil shall be made out of not less than 27G thick 5/8" dia. copper pipe of 4 row / 6 row deep with 12 fins per inch. with SS 304 Drain Tray. Filter section consists of 10 & 20 micron filters with efficiency down to 90%. The outlet of the Air Handling Unit shall be installed with Opposed Balde Aerofoil shape Damper & Fire damper of 90 Min Rating with Fusible Link. The Air Handling Unit Shall have necessary drive set. All the Motors shall be of three phase & EFF Class 1. The Air Handling Unit shall be provided with Electrical Starter Panel with VFD & Bypass Arrangement. The AHUs to be provided with thermal Break profile. Vendor to refer detailed AHU Data Sheet attached seperately.

Supply, Installation, Testing & Commissioning of Floor Mounted Double Skin Air Handling Units made out of Alu. Extruded Profile with Thermal Break Profile. The AHU panels fabricated out of 0.6 mm thick Pre-Coated G.I. Sheet with 43 mm / 47 mm PUF Insulated Panel. Blower Section shall consists of statically & dynamically balanced Forward Curved Blower capable of delivering 10000 CFM of air quantity at 60 mm total static pressure. The cooling coil shall be made out of not less than 27G thick 5/8" dia. copper pipe of 4 row / 6 row deep with 12 fins per inch. with SS 304 Drain Tray. Filter section consists of 10 & 20 micron filters with efficiency down to 90%. The outlet of the Air Handling Unit shall be installed with Opposed Balde Aerofoil shape Damper & Fire damper of 90 Min Rating with Fusible Link. The Air Handling Unit Shall have necessary drive set. All the Motors shall be of three phase & EFF Class 1. The Air Handling Unit shall be provided with Electrical Starter Panel with VFD & Bypass Arrangement. The AHUs to be provided with thermal Break profile. Vendor to refer detailed AHU Data Sheet attached seperately.

Supply, Installation, Testing & Commissioning of Floor Mounted Double Skin Air Handling Units made out of Alu. Extruded Profile with Thermal Break Profile. The AHU panels fabricated out of 0.6 mm thick Pre-Coated G.I. Sheet with 43 mm / 47 mm PUF Insulated Panel. Blower Section shall consists of statically & dynamically balanced Forward Curved Blower capable of delivering 8000 CFM of air quantity at 60 mm total static pressure. The cooling coil shall be made out of not less than 27G thick 5/8" dia. copper pipe of 4 row / 6 row deep with 12 fins per inch. with SS 304 Drain Tray. Filter section consists of 10 & 20 micron filters with efficiency down to 90%. The outlet of the Air Handling Unit shall be installed with Opposed Balde Aerofoil shape Damper & Fire damper of 90 Min Rating with Fusible Link. The Air Handling Unit Shall have necessary drive set. All the Motors shall be of three phase & EFF Class 1. The Air Handling Unit shall be provided with Electrical Starter Panel with VFD & Bypass Arrangement. The AHUs to be provided with thermal Break profile. Vendor to refer detailed AHU Data Sheet attached seperately.

Supply, Installation, Testing & Commissioning of Floor Mounted Double Skin Air Handling Units made out of Alu. Extruded Profile with Thermal Break Profile. The AHU panels fabricated out of 0.6 mm thick Pre-Coated G.I. Sheet with 43 mm / 47 mm PUF Insulated Panel. Blower Section shall consists of statically & dynamically balanced Forward Curved Blower capable of delivering 7500 CFM of air quantity at 60 mm total static pressure. The cooling coil shall be made out of not less than 27G thick 5/8" dia. copper pipe of 4 row / 6 row deep with 12 fins per inch. with SS 304 Drain Tray. Filter section consists of 10 & 20 micron filters with efficiency down to 90%. The outlet of the Air Handling Unit shall be installed with Opposed Balde Aerofoil shape Damper & Fire damper of 90 Min Rating with Fusible Link. The Air Handling Unit Shall have necessary drive set. All the Motors shall be of three phase & EFF Class 1. The Air Handling Unit shall be provided with Electrical Starter Panel with VFD & Bypass Arrangement. The AHUs to be provided with thermal Break profile. Vendor to refer detailed AHU Data Sheet attached seperately.

Supply, Installation, Testing & Commissioning of Floor Mounted Double Skin Air Handling Units made out of Alu. Extruded Profile with Thermal Break Profile. The AHU panels fabricated out of 0.6 mm thick Pre-Coated G.I. Sheet with 43 mm / 47 mm PUF Insulated Panel. Blower Section shall consists of statically & dynamically balanced Forward Curved Blower capable of delivering 5000 CFM of air quantity at 60 mm total static pressure. The cooling coil shall be made out of not less than 27G thick 5/8" dia. copper pipe of 4 row / 6 row deep with 12 fins per inch. with SS 304 Drain Tray. Filter section consists of 10 & 20 micron filters with efficiency down to 90%. The outlet of the Air Handling Unit shall be installed with Opposed Balde Aerofoil shape Damper & Fire damper of 90 Min Rating with Fusible Link. The Air Handling Unit Shall have necessary drive set. All the Motors shall be of three phase & EFF Class 1. The Air Handling Unit shall be provided with Electrical Starter Panel with VFD & Bypass Arrangement. The AHUs to be provided with thermal Break profile. Vendor to refer detailed AHU Data Sheet attached seperately.

Supply, Installation, Testing & Commissioning of Ceiling Suspended Double Skin Air Handling Units made out of Alu. Extruded Profile with Thermal Break Profile. The AHU panels fabricated out of 0.6 mm thick Pre-Coated G.I. Sheet with 43 mm / 47 mm PUF Insulated Panel. Blower Section shall consists of statically & dynamically balanced Forward Curved Blower capable of delivering 3000 CFM of air quantity at 60 mm total static pressure. The cooling coil shall be made out of not less than 27G thick 5/8" dia. copper pipe of 4 row / 6 row deep with 12 fins per inch. with SS 304 Drain Tray. Filter section consists of 10 & 20 micron filters with efficiency down to 90%. The outlet of the Air Handling Unit shall be installed with Opposed Balde Aerofoil shape Damper & Fire damper of 90 Min Rating with Fusible Link. The Air Handling Unit Shall have necessary drive set. All the Motors shall be of three phase & EFF Class 1. The Air Handling Unit shall be provided with Electrical Starter Panel with VFD & Bypass Arrangement. The AHUs to be provided with thermal Break profile. Vendor to refer detailed AHU Data Sheet attached seperately.

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nos.,Y strainer-1 No.,Balancing valve 2 way Mixing / Diverting Valve with Actuator & Sensor complete with bypass line, with temp.and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for following AHUs as per requirement. AHU 25000 CFM (100 MM PIPE SIZE)

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nos.,Y strainer-1 No.,Balancing valve 2 way Mixing / Diverting Valve with Actuator & Sensor complete with bypass line, with temp.and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for following AHUs as per requirement. AHU 10000 CFM (80 MM PIPE SIZE)

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nos.,Y strainer-1 No.,Balancing valve 2 way Mixing / Diverting Valve with Actuator & Sensor complete with bypass line, with temp.and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for following AHUs as per requirement. AHU 8000 CFM (65 MM PIPE SIZE)

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nos.,Y strainer-1 No.,Balancing valve 2 way Mixing / Diverting Valve with Actuator & Sensor complete with bypass line, with temp.and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for following AHUs as per requirement. AHU 7500 CFM (65 MM PIPE SIZE)

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nos.,Y strainer-1 No.,Balancing valve 2 way Mixing / Diverting Valve with Actuator & Sensor complete with bypass line, with temp.and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for following AHUs as per requirement. AHU 5000 CFM (50 MM PIPE SIZE)

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nos.,Y strainer-1 No.,Balancing valve 2 way Mixing / Diverting Valve with Actuator & Sensor complete with bypass line, with temp.and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering for following AHUs as per requirement. AHU 3000 CFM / 2400 CFM (40 MM PIPE SIZE)

Supplying and erecting 250 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Comtech Telesolutions Pvt. Ltd.

J D ENTERPRISES

VENUS MEP SERVICES