SPL REPAIR TO BLDG NO P-169 IN THE AOR OF AGE B/R-II UNDER GE 864 EWS (JOB NO W/SR (BLDG)-16/BB CANTT/2025-26)

Amount

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, including dismantling old unserviceable galvalume all as secured and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, including dismantling old unserviceable galvalume complete all as secured and directed.

M&L second class hardwood clean sawn in scantling as in purlins, Rafters and trusses etc, including dismantling old unserviceable scantling complete all as specified and directed.

S&F 25mm thick second class clean sawn softwood fixed with nails in any situation as in eaves board complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L 6mm thick non asbestos fibre cement/Pre laminated self embossed texture designer board E-Board classic 600mmx600mm, HSPC (high pressure steam cured) to be fixed or inserted to pre laminated GI frame work for seamless ceiling size 600mmx600mm with main runner 38mmx24mmx0.9mm thick, cross tee 8.6mmx0.9mm and wall angle 19mmx19mmx0.9mm duly suspended with 6mm dia GI wire hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip, including dismantling old unserviceable non asbestos fibre board complete all as specified and directed.

S&F solid PVC wall lining/ceiling consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site including 5mm thick 35mm wide PVC fillets frame as per manufacturer specification and drawing, including dismantling old unserviceable PVC wall lining complete all as specified and directed

Taking down chowkhats or frames with shutter area not exceeding 1.50 Square metre (without taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete, all as specified and directed.

Taking down chowkhats or frames with shutter area exceeding 1.50 Sqm and not exc 4.00 Sqm (without taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partition (fixed portions) with extruded built up standard tubular sections/3 track and other sections of approved make conforming to IS-733 and IS-1285, fixing with dash fasteners of required dia and size including necessary foaming up the gaps at junction i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight , mitred and jointed mechanically where required including cleat angle, Aluminium snap beading for glazing/panelling CP brass/stainless steel screws, all complete as per architectural drawings and as directed Engineer-in-Charge.

S&F Powder coating of any colour (thickness of powered coating not less than 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 Kg/Rm including necessary joining cleats, glazing clips, rubber neoprene packing, locking arrangement, handles, tower bolt & necessary butt Hinges and ACP sheet in bottom panel etc complete all as specified and directed by Engineer-in-Charge.

S&F powder coating of any colour (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters fixed/sliding/side hung type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handle, locking arrangement, necessary butt hinges, tower bolts etc complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according o IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening including powder coated aluminium (minimum thickness of powder coating 50 micron) all compete as per requirement and directed by Engineer-in-Charge.

M&L for preparation of old plastered or un-plastered surface of walls/ceiling and applying two coats of plastic emulsion paint (colour shade as approved by GE) complete all as specified and directed.

S&F in repair for ACP sheet 4mm thick in aluminium frame including necessary fittings, complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25 mm dia stainless steel drapery curtain rods, heavy duty, fancy type with fancy brackets & domes two in each door and window (Sample as approved by GE), complete all as specified and directed.

S&F in repair venation blind of 100mm wide strip for windows including headrail section, top fix (spring), end caps, chain & cord, cord weight, stabilising chain with C clip, ballast weight, hanger & carrier track and all other necessary fittings & fixtures (design and colour as approved by GE), complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius built in cement mortar 1:6, including dismantling old unserviceable brick work in cement mortar complete all as specified and directed

Takng down cement plaster on brick or stone walls etc built in cement or lime mortar and including racking out joints, hacking for key, scrubbing down with wire brush etc complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:6 on fair faces of brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 other than fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly untreated wall surface and applying two coats of plastic emulsion paint over one coat of primer complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded in any mortar complete all as specified and directed

M&L 20mm thick granite (of any type) work (table rubbed and mirror polished to give high glossy finishes) in step, jambs, pillars, window-cills, cooking platform & in vertical surface of walls area should not be less than 2.5 Sqm and like in cement mortar 1:4 including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed / backing in CM 1:4 including complete all as specified and directed.

All as per ser item No 26 here-in-before but except stone

Dismantling of timber scantling of any description complete all as specified and directed.

M&L for mild steel framed work such as in angle iron frames for staging of water tanks, shed, purlins, Rafters, trusses and similar work etc, confirming to Fe-290, Grade E-165, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L plain cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in foundation/flooring including demolition of old unserviceable cement concrete complete all as specified and directed.

M&L for RCC 1:1.5:3, type B1 (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roof landing, balconies, deck slab and shelves and the like, including demolition of old reinforced concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

M&L formworks to soffits of suspended slabs such as roof slabs , floors slabs, landings and similar work not exceeding 200mm thick (Horizontal or slopping) complete all as specified and directed.

S&F in repairs sinks with drainage board, made of stainless steel 1.0mm thick, suitable for kitchen or laboratory with plugs, washers and wastes including bedding in CM to dwarf wall or including cast iron cantilever brackets of suitable size and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

M&L for providing precast cement concrete drain/man hole cover of PCC 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and directed

S&F 1000 litres capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including brass float valve all as specified in SSR Part I including dismantling old unserviceable PVC water tanks exc 500 litres and not exc 1000 litres capacity etc complete all as specified and directed.

Dismantling of boarding, any description of, fixed in any position with nails complete all as specified and directed.

S&F 12mm thick plywood, grade BWR, type BB fixed with nails as in cupboard shutter/ceiling complete all as specified and directed.

S&F 9mm thick plywood, grade BWR, type BB fixed with nails as in wall /ceiling/cupboard shutter/showcase etc complete all as specified and directed.

M&L prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F 30mm width flap, continuous (piano) hinges, mild steel, bright finish or electrogalvanized all as specified and directed.

S&F 1.5mm thick decorative laminate type 1 of surface finish, colour and pattern including necessary fillets/ cornices as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F 3 layer PPR polypropylene random co polymer concealed pipes of 20 mm outer dia SDR7.4 (PN16) UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete concealed to walls, ceiling or in floors, including taking up or down complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L vitrified ceramic tiles light/dark shade and texture double charge/ultra charged shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match with shade of tile laid over and including screed bed or bedding layer 20mm thick in CM 1:6 complete all as specified and directed.

M&L for digital non-skid ceramic tiles on floor of size 600mmx600mm and 8 to 10mm thick etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with shade of tile laid over and including screed bed or bedding layer 15mm thick in CM 1:4, complete all as specified and directed.

M&L for digital ceramic vitrified glazed tiles light/dark shade and texture double charge/ultra charged on wall 1200mm x 600mm and 7 to 8mm thick etc set and jointed in neat cement slurry with 5mm spacers & filling the joints with epoxy grout filling as per manufacturer's instruction and pointed in white or coloured cement to match with shade of tile laid over and including screed bed or bedding layer 10mm thick in CM 1:4 complete all as specified and directed.

M&L for cutting into existing manholes of internal dia of pipe 150mm for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L for 110mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls, including dismantling old unserviceable PVC (SWR) pipe complete all as specified and directed.

M&L for 75mm bore PVC (SWR) pipe, single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls, including dismantling old unserviceable PVC (SWR) pipe complete all as specified and directed.

M&L for cutting openings of brick wall built in cement mortar or cement lime mortar through brick walls for door, window and other opening or enlarging existing openings , concerting window into door opening etc or cutting out defective brick work for under- pining, including providing fixing and removing shoring, cleaning and stacking bricks removing surplus serviceable bricks hard core etc to store and rubbish not exc 50m complete all as specified and directed.

S&F stack clamp, made out of flat iron of size 50mmx5mm and 16mm dia round iron stays including bolts and nuts and screwing ends of stay to wall or roof for 75mm bore pipe, complete all as specified and directed.

S&F PVC(SWR) branch piece single equal or unequal 110mm bore complete all as specified and directed.

S&F PVC(SWR) branch piece single equal or unequal 75mm bore complete all as specified and directed.

S&F PVC(SWR) bends any radius 110mm bore complete all as specified and directed.

S&F PVC(SWR) bends any radius 75mm bore complete all as specified and directed.

S&F PVC(SWR) 'S' trap any radius 110mm bore complete all as specified and directed.

S&F PVC(SWR) vent cowl any radius 110mm bore complete all as specified and directed.

S&F in repairs vitreous China oval type wash basin of inclusive 32mm waste fittings, brass, chromium plated ,waste pipe etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement etc complete all as specified and directed.

S&F in repair vitreous China wash down water closet one piece pan (Pedestal pattern), white/colour (including all fitting all fixing bolts, flushing cistern, jet spray and flush pipe) complete all as specified and directed . Make : Cat part No - Lys-Wht-88515300UFSMUN or techno commercially equivalent make/model as approved by GE.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe) including PVC seat cover (closed pattern) and CP health facet , connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete all as specified and directed.

S&F in repair shower rose large over head shower CP with arrow complete all as specified and directed. Make Jaquar Cat Part No - OH-CHR-1637 or techno commercially equivalent make/model as approved by GE

S&F in repair CP towel rack complete all as specified and directed. Make :- Jaquar Cat Part No - AKP-CHR-3578195 or techno commercially equivalent make/Model as approved by GE.

S&F in repair tubular holder (liquid Soap container) CP complete all as specified and directed . Make :-Jaquar Cat Part NO AKP-CHR-35741P or techno commercially equivalent make/model as approved by GE.

S&F in repair single towel rail 600mm long complete all as specified and directed. Make :- Jaquar Cat Part No AKP-CHR-35711PS or techno commercially equivalent make/model as approved by GE.

S&F in repair wall mixer telephonic type single lever 2 in 1 with telephonic shower complete all as specified and directed. Make :- Jaquar Cat Part No KUP-CHR-35125PM or techno commercially equivalent make/model as approved by GE.

S&F in repairs 15mm bore Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair angular stop cock fancy type/ concealed type CP complete all as specified and directed. Make :- Jaquar Cat Part No KUP-CHR-35053PM or techno commercially equivalent make/model as approved by GE.

S&F in repair toilet paper holder of stainless steel of size 10.5cmx9cm fixed to wall with chromium plated CP brass screw complete all as specified and directed Make:- Jaquar Cat Part No -AKP-CHR-35753P or techno commercially equivalent make/model as approved by GE.

S&F in repair glass shelf assembly, consisting of 5.50mm thick sheet glass, 12cm wide with chromium plated brackets, guard and railing 60cm long, complete all as specified and directed

S&F in repair corner glass shelf ,three set type, of size 300x300mm (lower), 225x225mm (medium) & 150x150mm (upper) fixed with Cp brass screws, complete all as specified and directed. Make :- Jaquar Cat Part No CAN-CHR-1173N or techno commercially equivalent make/model as approved by GE.

S&F CP grating 100mm dia complete all as specified and directed.

S&F PVC (SWR) 100mm dia multi floor trap with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair PVC connections 600mm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete including dismantling of old unserviceable railing all as specified and directed.

M&L chequered cement concrete tiles 30cmx30cm and 25mm thick with grey cement and pigments over and including 20mm thick screed bed or bedding layer in cement mortar 1:6 over and including 75 mm thick PCC 1:4:8 type D2 (using 40mm crushed stone aggregate), set, jointed and pointed in neat cement slurry complete all as specified and directed.

M&L for Endura coloured tiles 300mmx300mm and 10mm thick confirming to IS, laid in floors etc, set & jointed in neat cement mixed with pigment to match the colour of tiles over and including 20mm thick screed bed in cement mortar 1:6 including demolition/dismantling of old unserviceable tiles complete all as specified and directed.

S&F 150mm bore of pipe reinforced concrete pieces class Np-2 laid jointed complete with collars including dismantling of old unserviceable pipes complete all as specified and directed.

M&L for PCC 1:3:6, type C2 (using 40mm graded crushed stone aggregate) concrete bed to drain pipes 150mm including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S&F in repairs Aluminium (die cast body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

M&L for complete removal of existing treatment including scraping, removing all mud, cake with wire brush and gunny bags from old plastered surfaces and applying 3 mm thick white putty to obtain smooth/even finish using sand paper complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces including preparation complete all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 Ltrs capacity, valveless, symphonic action type, white with inlet, ball valve, float and handle including brackets, PVC 32mm dia flushing pipe etc., complete all as specified and directed.

M&L for chicken wire mesh galvanised steel wire 0.91 mm dia fixed with tinned tacks or wire staples and size of mesh 25 mmx 25 mm complete all as specified and directed.

M&L for half brick thick wall temporary closing of the door/passage opening in brick / stone masonry wall area not exc 5 sqm each with in CM 1:6, , plastering the surfaces and making dust free by applying plastic emulsion paint and fixing ACP sheets etc, and removal of complete brickwork plugging materials after phase wise completion of work and making good all surfaces as per site requirement , complete all as specified & directed.

M&L for temporary packing/sealing/covering of autoclave machine in CSSD or any object with following :- (a) Bubble wrap completely around all faces of machine/object (b) Cage around all faces of machine/object with wooden fillets section exc. 25 Sq cm but n exc 50Sq cm. (c) Covering with 6mm thick plywood around all faces of machine/object and removal of complete sealing material including connection/disconnecting as per site requirement after phase wise completion of work as per site requirement , complete all as specified & directed.

M&L Anti-microbial & mold resistant acoustic fiberglass false ceiling 9.5(+/- 0.2) mm thick complying with relevant ISI standard width (mm) 595 (+/-0.2) & Length (mm) 595 (+/-0.2) Square edge white with more than 80% light reflectance and Humidity resistance -70% to -90%. Face side laminated with Biocide treated white PVC lamination & Rear side laminated with 12 micron metalized polyester film with antifungal & antimicrobial properties. Surface shall be smooth, wipeable suitable for health care & hygienic applications to be fixed or inserted to pre laminated GI frame work for seamless ceiling size with main runner 38mmx24mm and 0.9mm thick, cross tee 8.6mmx0.9mm and wall angle 19mmx19mm and 0.9mm duly suspended with 6mm dia GI wire hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip, including all other necessary fittings & fixtures & dismantling of old boarding/ ceiling complete all as specified and directed.

M&L for white Marble flooring 20mm thick machine cut, bedded jointed and pointed including cutting over and including 15mm screed bed of CM 1:4 & fixed white cement slurry and cutting, mirror polished including demolition of old unserviceable flooring complete all as specified & directed.

M&L for cutting and Mirror polishing on marble/ granite/ Kota stone/ stone work as in floor of any description where ever required to give high gloss finish complete all as specified & directed.

All as per ser item No 93 here-in-before but in vertical surfaces.

M&L for 3mm thick Epoxy coving as in junction of floor & wall with 6kg/sqm, forming minimum 3 mm thickness over scratch coat and finishing, It should have compressive strength of more than 45 mpa and flexure strength of 15 MPa and having shore hardness of 70 days and temperature withstanding ability of -15 to 60 degree C, complete all as per Manufacture's instruction and as directed by Engr-In-Charge.

S&F for wall hung stainless steel surgical scrub sink construction utilizing medical grade 304 stainless steel of 3 bay size 79" wide x 27 1/4" deep x 38" high including all fittings & fixtures as per drgs in CA and as per site requirement. complete all as specified & directed.

S&F long lever 15mm elbow operated healthcare mixture for hot & cold water mixture to use in high-risk areas like operation theatres and examination rooms complete all as specified & directed

M&L for walling of random rubble, brought upto course as in walls, bedded and solidly hearted built in CM 1:4 including demolition of old unserviceable brick work or stone masonry complete all as specified & directed.

Extra over walling hammer dressing with mix depositing on face from straight edge held against the dressed surface n.exc 40mm complete all as specified and directed.

M&L keyed pointing to random or polygonal rubble, uncoursed or brought upto course in CM 1:3 complete all as specified and directed.

M&L for brickwork with old sized subclass 'B' bricks straight or curved on plan exc any radius and built in CM 1:6 as in half brick thick wall etc complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair without using extra cement including making joints every 2.5m and corner filled with bitumen 85/25 including demolition complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for cutting out concrete blocks, slabs, brickwork or stone masonry (in alternate course), forming toothing's for and bonding new work as per shape required at site in mortar CM 1:4 of precast cement concrete 1:1.5:3 (using 20mm graded stone aggregate) to old work, including new materials entering old wall complete all as specified. Note:-Toothing and bonding shall be measured on vertical face in contact with old wall only.

Supply, fixing, installation, commissioning and testing of hi wall mounted basesd invertor type three star rated split AC unit of rated capacity 2.0 TR invertor based hot and cold type indoor and out door unit complete set with having both cooling and heating function and digital display inverter type complete with cordless remote control and full filling of initial refrigerant gas along with having in built heating and cooling arrangement alongwith invertor type rotary based DC compressor unit and suitable for operation for 230 Volt 50Hz single phase electric supply including providing of MS stand & bracket for fixing of outdoor unit and indoor unit system and also providing of both type/size of suction and discharge copper refrigerant piping attachment system in any lengthy and duly fixed both piping connected from outdoor unit to indoor unit attachment system complete along with duly over lapped it by nitrile insulation, with insulation taping work and also providing of suitable size of additional drain pipe line system up to ground level for dropping out the condensing water outside area from evaporator unit attachment system and making electric connection with 3 core copper cable of suitable size and including making of hole on existing type wall/roof/ceiling etc for jointing of inter conncetion of indoor & outdoor attachment system and after making good to all disturbed surface match to existing wall complete all as specified and directed.

Supply, fixing, installation, commissioning and testing of hi wall mounted basesd invertor type three star rated split AC unit of rated capacity 1.5 TR invertor based hot and cold type indoor and out door unit complete set with having both cooling and heating function and digital display inverter type complete with cordless remote control and full filling of initial refrigerant gas along with having in built heating and cooling arrangement alongwith invertor type rotary based DC compressor unit and suitable for operation for 230 Volt 50Hz single phase electric supply including providing of MS stand & bracket for fixing of outdoor unit and indoor unit system and also providing of both type/size of suction and discharge copper refrigerant piping attachment system in any lengthy and duly fixed its both piping connected from outdoor unit to indoor unit attachment system complete along with duly over lapped it by nitrile insulation, with insulation taping work and also providing of suitable size of additional drain pipe line system up to ground level for dropping out the condensing water outside area from evaporator unit attachment system and making electric connection with 3 core copper cable of suitable size and including making of hole on existing type wall/roof/ceiling etc for jointing of inter conncetion of indoor & outdoor attachment system and after making good to all disturbed surface match to existing wall complete all as specified and directed.

Supply, fixing, installation, commissioning and testing of wall mounted hanging based automatic operation based digital type automatic voltage stabilizer unit of rated capacity 5 KVA complete and suitable using for single phase naturally air cooled indoor type with having digital display and suitable for operation on single phase AC supply and with having designed voltage for input & output voltage 130 Volts to 250 Volts with accuracy + 2.5% and with having low voltage cut off 130 (-) 5 Volts and high voltage cut off 250 V (+5) Volts along with start time delay system with time delay adjustable up to 30 second to 1.5 minutes system unit complete all as specified and directed.

Supply, installation, commissioning and testing of commercial type Air curtain complete unit ISI mark with having automatically auto on/off mode based on motion sensor operating system with door opening size 40"x78" used for the purposed prevention of dust and conditioned air losses, and suitable operation for single phase, 220 V, 50 HZ, and including made out of MS/CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1 - 1.5 m/sec air velocity at floor level for door opening as specified complete unit all as specified and directed by EIC.

M&L for taking down carefully existing old burnt out / unserviceable aluminium / copper point wiring system any type/ size and any description complete for light, fan, bell, socket, power points etc complete including removing the all type of fittings & fixture along with it connected fixing accessories such as all switches, sockets, ceiling roses, holder, regulators, bell etc complete and removing of all the old materials from the site including making good to disturbed surfaces to match with existing finishes complete all as specified and directed by EIC .

M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring used in any length wiring system and the wire made out of PVC insulated multi core copper conductor wire FRLS of 1100 Volts grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked along with its all type of fixing and connected accessories and drawn through wiring system concealed in wall with the help of PVC conduit pipe used in any lengthy wiring system and including providing of suitable sizes of pressed steel terminal sunken type of modular junction box along with modular type of back and face top cover plate frame complete set for mounting/housing of modular type/size switches sockets, regulators etc and duly fixed its concealed in wall and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 Volts grade with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making good to all disturbed surfaces of wall/ceiling floor etc area of new wiring system and to match to it as per the existing surface of wall/ceiling etc one light point / fan point wiring system controlled by one way switching system area complete all as specified & directed by EIC. Note - Type of wiring work and layout of wiring fixing/laying work to be carried out on site shall be as per user requirement or decided by EIC.

All as per ser item No 110 here-in-before but one 5 Amps socket outlet point wiring system fixed on same board & controlled by one way switching system complete.

All as per ser item No 110 here-in-before but one 5 Amps socket outlet point wiring system fixed on independent board & controlled by one way switching system complete .

All as per above ser item No 110 here-in-before but one bell point wiring system fixed on board and controlled by one way bell push switching system complete .

All as per ser item No 110 here-in-before but using PVC insulated FRLS wire 1100 volt grade with multistranded copper conductor wire of size 2.5 Sq. mm for power socket point wiring system and also providing of 2.5 sqmm PVC insulated FRLS wire 1100 Volts grade with multistranded copper conductor wire used as a continuous earth wire for power point wiring system complete .

All as per ser item No 110 here-in-before but using PVC insulated FRLS wire 1100 Volts grade with multistranded copper conductor wire of size 4.0 Sq. mm for power socket point wiring system and also providing of 4.0 sqmm PVC insulated FRLS wire 1100 volt grade with multistranded copper conductor wire used as a continuous earth wire for power point wiring system complete .

S&F of modular type switch 5/6 Amps 220 Volts AC with one module based complete all as specified and directed.

S&F of modular type socket of 5/6 Amps 220 Volts AC, 3/5 pin type with two modular based complete all as specified and directed.

S&F of modular type switch of 15/16 Amps 220 Volts AC one module based complete all as specified and directed.

S&F of modular type socket of 15/16 Amps 220 Volts AC 5/6 multy pin type with two modular complete all as specified and directed.

S&F of modular type bell push flush type single pole with one module based complete all as specified and directed.

S&F in renewal bell Ding Dong Type, 220 Volts AC, single Pole complete as per specified and directed

S&F in renewal one/two modular type step type/hum free electronic fan regulator along with speed control know complete all as specified and directed.

S&F ceiling rose three terminals type made out of polycarbonate , isolated body complete all as specified and directed.

S&F in renewal of wall mounted slim batten type LED tube light fitting of rated capacity1x 20W/22W up to maximum 4 feet long decorative box type with driver, holder including LED light with having energy efficient type required in both warm/white type colour complete including providing of suitable type flate flexible cable for electric connection from ceiling rose to fitting complete all as specified & directed

S&F in renewal of recessed / ceiling concealed mounted flat slim type of panel square shape with LED luminaire panel light fitting of approximate size 600 mm x 600 mm (2 feet x2 feet type) of rating capacity in 35W to 40 W with 220 Volts AC supply system and having recessed decorative type with high performance energy saving LED light fitting, driver, holder & LED lamps complete fitting and using for roof ceiling area and required fitting use in both warm/white type colour complete set providing of suitable type of flat flexible two/three core cable and making electric connection complete set including making in additional cutting of hole work on existing ceiling surface area (when if required at site) for setting & fixing of new light fitting complete all as specified and directed.

S&F in renewal of recessed/ceiling concealed mounted down lighter light fitting of round/Square flate shapes decorative type of rating capacity in 15 Watts to 18 Watt with 220 Volts AC supply system and having high performance energy saving LED light fitting, driver, holder & LED lamps complete fitting and using for roof ceiling area and required fitting use in both warm/white type colour complete set providing of suitable type of flat flexible two/three core cable and making electric connection complete set including making in additional cutting of hole work on existing ceiling surface area (when if required at site) for setting & fixing of new light fitting complete all as specified and directed.

S&F in renewal of LED tube light fitting of rated capacity1x 10W 2 feet long decorative box type with driver, holder including LED light with having energy efficient type required in both warm/white type colour complete including providing of suitable type flate flexible cable for electric connection, from ceiling rose to fitting complete all as specified & directed.

S&F in renewal of wall bracket surface mounted decorative light fitting with having stainless steel rust free fixture with white glass diffuser along with bulb holder based adaptor suitable used for 7.5W / 9 W LED filament lamp E27 base system including providing of 1N x 9W LED lamp in required fitting use in both warm/white type colour complete light fitting set and including providing of suitable type of flate flexible two/three core cable and making electric connection, complete all as specified and directed.

S&F in renewal of environment friendly LED street light fitting of rated capacity 50 Watts with having LED driver, lamp bracket holding housing with impact and corrosion resistant and suitable using for out door type made out of high pressure die cast hosing with heat resistant glass complete fitting including providing of suitable size/type of dia GI pipe light grade bracket and it to match/setting the new fitting fixture hole attachment system of suitable bracket length up to 1.0 mtr long and make to shape / bend of 120 degree angle including duly fixed it existing pole /bldg wall/ roof with the help of MS fixing clamp along with nut bolt and including providing of suitable type of flate flexible two/three core cable and making electric connection complete all as specified and directed.

S&F in renewal of surface/wall mounted LED bulk head luminaries light fitting of rated capacity 10W including LED lamp & driver suitable used for out door type with dust and water proof with energy efficient saving fitting complete set and use in both warm/white type colour complete and including dully fixed on bldg. wall surface including providing of suitable type of flate flexible two/three core cable and making electric connection and including taking down of old fitting all as specified and directed.

S&F in renewal of angular/batten shape type lamp holder with PVC/ Polycarbonate insulated body, along with brass adaptor and back plate for housing of bulb Including providing of rechargeable LED bulb of capacity 7/9 Watts warm/ white colour type complete all as specified and directed .

S&F of wall mounted fan 400 mm sweep of single phase 230 Volts AC with having pull cord oscillating type single piece AS blade, three speed pull cord control complete with blade and guard framing support & connecting accessories and fixed/grouting on wall/roof with MS fastener, nut & bolt including providing flate flexible copper wire and making all electrical connection complete all as specified and directed.

Supply, fixing commissioning and testing of electric ventilation exhaust fan of size 200 mm sweep complete AC single phase 230 Volts and made out of sturdy engineering plastic body complete with blade and louvers with shutter and also providing or making/ construction work of suitable type/size of hole on wall or out of any type of hole in window/door system for installation /fixing of exhaust fan after fan fixing work making good to all disturbed hole surface area of wall/ceiling and floor area and to be match/dressing to it as per the existing surface so wall/floor/ceiling etc by cement plastering work complete all as specified and directed by Engineer -in- charge

Supply, fixing commissioning and testing of venting exhaust fan of size 300 mm sweep complete AC single phase 230 V And made out of mild steel body, complete with blade and louvers with shutter and also providing or making/ construction work of suitable type/size of hole on wall or out of any type of hole in window/door system for installation /fixing of exhaust fan after fan fixing work making good to all disturbed hole surface area of wall/ceiling and floor area and to be match/dressing to it as per the existing surface so wall/floor/ceiling etc by cement plastering work complete all as specified and directed by Engineer -in- charge

Supply, fixing and commissioning and testing of ceiling fan 1200 mm sweep with 5 star rating of single phase 230 Volts AC along with blade, down rod, canopy, clamps with reel insulator, & accessories and providing of MS fan hook and dully fixed it on ceiling/roof including providing flate flexible copper wire and making all electrical connection complete all as specified and directed.

S&F electric water heater (geyser) of storage capacity 25 ltrs with having steel body and inner tank along with heating element up to 2 KW complete set with all accessories such as safety valve, thermostat, NRV, PVC Connection and dully fixed it on wall with the help of MS fastener ,nut bolts and making electric connection complete all as specified and as directed by Engineer-in-Charge.

S&F of sheet metal enclosure duly powder coated with single pole and neutral enclosure with having a two pin and earth plug & top and mounted channel along with one 01 MCB SP 32 Amp and dully fixed surface on wall or concealed in wall and making all necessary electrical connection including taking down of existing- unserviceable DBs a as required at site or directed complete all as specified and directed.

S&F of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of size/type for vertical type distribution board vertical load line type of rating VTPN 4 way type 415 volt 3 phase AC supply holding system with IP protection rating IP 65/ 66 with ISI marked and having fitted neutral and earth link bus bar and mounted base channels and blanking plates suitable for holding of main MCCB as incomer and out going MCB complete system along with providing and mounting in side of DB box of 01 No of MCCB TPN 160 Amps with breaking rusting capacity 25 KA and having adjustable setting type and also providing of 12 Nos of MCB SP 63 Amps 10KA 'C' curve type of the same manufacture make as per of distribution board make complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing DBs complete all as specified and directed by EIC.

S&F of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of size/type of distribution board of rating SPN 12 way type 220 Volts AC supply system with IP protection rating IP 65/66 with ISI marked and having neutral and earth link bus bar and mounted base channel suitable for holding MCBs incomer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing unserviceable meter and DBs complete all as specified and directed by EIC.

S&F of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of size/type of distribution board of rating SPN 8 way type 220 Volts AC supply system with IP protection rating IP 65/66 with ISI marked and having neutral and earth link bus bar and mounted base channel suitable for holding MCBs incomer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing unserviceable meter and DBs complete all as specified and directed by EIC.

S&F of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of size/type of distribution board of rating SPN 6 way type 220 Volts AC supply system with IP protection rating IP 65/66 with ISI marked and having neutral and earth link bus bar and mounted base channel suitable for holding MCBs incomer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing unserviceable meter and DBs complete all as specified and directed by EIC.

S&F of MCB SPN 63 Amps with breaking capacity 10KA 'C' Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring connection complete including taking down of old unserviceable MCB complete all as specified.

S&F of MCB SP 06 to 32 Amps with breaking capacity 10KA 'C' Curve series, 220 Volts, 50 Hz AC supply complete and also making suitable size / type of electric wiring connection complete including taking down of old unserviceable MCB complete all as specified.

S&F of sub main wiring system with PVC insulated FRLS wire,1100 Volts grade with multistranded copper conductor wire of size 3 Run of 25 Sqmm and 1 Run of 16 Sqmm (Nominal area) any type any length drawn through concealed in wall along with PVC conduit pipe heavy duty with its all fittings and connected accessories complete all as decided and direction by Engineer- in-Charge including taking down old unserviceable sub main wiring system complete all as specified and directed . Note: Three runs of 25 sqmm and one run of 16 sqmm cable and one run of PVC conduit shall be measured as one RM.

All as per serial item No 144 here-in-before but wire/cable of size/type single core of 2 run of 10 Sqmm and 1 run of 10 Sqmm (Nominal area) ISI Marked, complete all as specified and directed.

All as per serial item No 144 here-in-before but wire/cable of size/type single core of 2 run of 6 Sqmm and 1run of 6 Sqmm (Nominal area) ISI Marked, complete all as specified and directed.

All as per serial item No 144 here-in-before but wire/cable of size/type single core of 2 run of 4 Sqmm and 1run of 4 Sqmm (Nominal area) ISI Marked, complete all as specified and directed.

All as per serial item No 144 here-in-before but wire/cable of size/type single core of 2 run of 16 Sqmm and 1run of 16 Sqmm (Nominal area) ISI Marked, complete all as specified and directed.

M&L for earthing work complete with galvanised steel earth plate electrode 60 cm x 60 cm and 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level and connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers of galvanised steel and to be protected by GI pipe up to 25 mm bore light grade & connected to earth test point/main switch board or main control board and also providing charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil all as shown in Electrical Plate No 3 of SSR part -I. and also making arrangement of 20 mm dia bore galvanised iron pipe (medium grade) for water and making funnel, wire mesh, and also including provision of concrete pit cover framing work in PCC 1:2:4 type B-1 (using 20mm graded of stone aggregate) with X PM (weight not less than 4 Kg/Sqm) and outer frame work with top concrete pit cover and handle for lifting of cover complete work all as specified and directed.

All as per ser item No 149 here-in-before but using copper plate 60x60cm and 3.15 mm thick electrode alongwith using 20x3 mm copper strip as earthing lead complete work all as specified and directed.

S&F of rigid non metallic PVC conduit of size 32/40 mm bore heavy duty with all fitting laid in trenches/ wall including providing clamping arrangement for holding of pipe on wall in proper size of clamps, nut bolt ,and washer etc complete all as specified and directed.

S&F of GI earth continuity earthing lead of 4 mm dia bore galvanised Iron or steel wire with all fitting duly laid in trenches /wall including providing clamping arrangement for holding on wall in proper size of clamps, nut bolt ,and washer etc complete all as specified and directed.

S&F of copper earth continuity earthing strip of size 20 x 3 mm with all fitting duly laid in trenches /walls including providing clamping arrangement for holding on wall in proper size of clamps, nut bolt ,and washer etc complete all as specified and directed.

M&L for taking down carefully of existing Fans/Geyser any sweep and removing Fan blade and all connected accessories and after cleaning or servicing and painting of existing fan with blade with the help of nut bolts fastener, rubber reel, washer and including making the suitable type /size of hanging arrangement for re fixing of fan and geyser on ceiling/ wall surface area in any position on same place complete work and making with 2/3 core electrical wire for connection complete all as specified and directed.

M&L for taking down carefully of existing both type/size of Medical oxygen & vacuum gas pipe line system along with connected fixing accessories like valve and port complete all as per existing type /sizes sample of and completion of work after refixing all the same on its original position with the help of cutting , drilling , welding, brazing work in any position with hot / cold welding work duly fixed it with the existing medical gas pipe line attachment system and making it leakproof along with providing of all type of fitting/fixing accessories i.e. porcelain saddle nut bolts fastener, washer etc complete all as specified and directed by EIC.

M&L for cutting existing both type/size of Medical oxygen & vacuum gas pipe line system carefully before starting the work and including providing and inserting of suitable type /size of 2 Nos of oxygen/vacuum gas line on/off of stopper copper valve as per existing type /size/ dia of bore for opening and closing of gas system and including blocking the both end of the existing both oxygen line system to further and dully fixed it with the help of cutting , drilling , welding, brazing work in hot /cold welding work and after completion of complete work jointing/ fixed it with the existing line attachment system and making it leakproof executing area complete all as specified and directed by EIC.

M&L for fixing of copper tubing of size 12 mm dia bore with having 0.9 mm wall thickness heavy duty or all as per existing type/size /dia of oxygen gas copper pipe line system complete all as per existing type/dia of sample/model and properly match to each other as per the existing gas pipe line system and duly fixing/laying work in any position for jointing and including dully fixed its with the help of cutting , drilling , welding, brazing work in hot/ cold welding work and jointing it with the existing line attachment system and making it leakproof along with providing of existing type fixing accessories i.e. porcelain saddle nut bolts fastener, washer etc complete all as specified and directed by EIC.

M&L for fixing of copper tubing of size 15 mm dia bore with having 0.9 mm wall thickness heavy duty or all as per existing type/size /dia of oxygen gas copper pipe line system complete all as per existing type/dia of sample/model and properly match to each other as per the existing gas pipe line system and duly fixing/laying work in any position for jointing and including dully fixed its with the help of cutting , drilling , welding, brazing work in hot/ cold welding work and jointing it with the existing line attachment system and making it leakproof along with providing of existing type fixing accessories i.e. porcelain saddle nut bolts fastener, washer etc complete all as specified and directed by EIC.

S&F 1/2' copper/Brass Ball/gate valve & port with complete end fittings heavy duty complete all as per existing type of sample, size of bore and type including providing of all fittings for medical gas pipe line system and dully fixed its with the help of cutting , drilling , welding, brazing work in hot /cold welding work and jointing it with the existing line attachment line system and making it leakproof along with providing of existing type fixing accessories i.e. porcelain saddle nut bolts fastener, washer etc complete all as specified and directed by EIC.

S&F in renewal of duct insulation materials of 50 mm thick nitrile insulated insulation/aroma flex insulation material any type any shape type and with having outer pre painted aluminium foil cover and duly cover it with the help of insulated suitable type/size of tap for proper covering/protection of AC duct work complete all as specified and directed.

M&L for carefully before starting the work closing/blocking of end portion of existing air duct diffuser area any type any size and including providing and inserting/fixing of suitable type /size and properly cover it with existing type of MS /GI sheet/PVC material all as decide and directed and make it air leakproof properly and after completion of work dismantling and removed it properly from site and after complete work supply, fixing in renewal of duct end air new diffuser & air end grill as per square & rectangular type/size and made of heavy duty PVC body & MS body type complete all as per existing type of sample & model with parameters & rated capacity and size/type etc with new replacing items shall be properly match to each other with existing old renewal vent diffuser / grill and duly fixed it on wall/ceiling area and suitable using it for operation of OT duct system and along with all type of fitting and fixing accessories based complete set of work all as specified and directed by EIC.

S&F of sheet metal encloser box outdoor type with IP 65/66 protection system duly weather proof with mounted channel and earth dolly and making of suitable hole for inlet /out let for cables inch providing of MCCB 200 Amps, 4 pole with breaking capacity 25 KA, 415 V 50 Hz, with having thermal magnetic /adjustable type complete set and duly fixed in wall with fixing accessories complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated armoured heavy duty electric cable with aluminium conductor 1100 Volts grade of size 70 sq. mm 3.5 core fixed in wall /roof with the fixing accessories duly fixed with suitable type of thimbles all as specified and directed.

Supply, laying and testing cable XLPE Insulated armoured heavy duty electric cable with aluminium conductor 1100 Volts grade of size 35 sq. mm 3.5 core fixed in wall /roof with the fixing accessories duly fixed with suitable type thimbles all as specified and directed.

Supply, fixing, installation, commissioning and testing of new age ceiling mounted double dome type LED Operation Theatre (OT) light fitting complete set for hospital alongwith having aerodynamically designed double dome based for suspended light, highly suitable for modern luminar flow for operation theatre alongiwith spring balance control sterilizable focusing handle and maneuvering handle. The handle should have control like switching mode power supply for light intensity control, longer reach of arm suitable for positioning the dome at any place on OT table system for better focusing/adjustable focusing with higher depth of illumination, glare less and duo shadowless optically balanced light sources and with having following technical specification- light source type- LED based and the stand should have 2 Nos of domes duly fitted with 35 Nos of LED's in each dome with having producing high output of 135000 lux + 135000 lux color temp less than 4100K and including 02 Nos of SMPS with intensity control-stepless control facility and suitable working operating on 220 Volts AC supply system complete all as per model No- Phililed S50 or Phililed S50D of Make- Philips or equivalent model and make alongwith brief technical specification with technical parameters & rated capacity and size/type etc are shall be properly match to each other of other ISI mark of approved make or all as decided and specified and directed by Engr-in-Charge and Accepting Officer and after making electrical connection complete all as specified and directed by Engr-in-Charge. Note: Taking down carefully of existing old unserviceable type of OT light fitting and deposit in safe custody of MES store for further action and direction.

M/S RATHER CONSTRUCTION CO (BID ID -3481656)

M/S Vivek Gupta and Co (BID ID -3472359)