REPAIR TO INTERNAL WATER SUPPLY CHAJJA, SANITARY FITTING, BRICK WORK, PLASTERING, SUNKEN AND OTHER MISC WORKS IN OTM/MD ACCN UNDER AGE B/R-I AT ITARANA ALWAR

Amount

Taking down cement plaster of any description on walls, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

M&L demolition of concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to location outside defence land complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specifed and directed.

M&L fly ash brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 mean radius, built in CM 1:6 except brick complete all as specifed and directed.

M&L brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick built in cement mortar 1:4 complete all as specifed and directed.

M&L rendering 15mm thick, plaster on fair faces of brick work or stone masonry or concrete surfaces in CM 1:6 including finished surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in CM (1:4) on stone masonry surfaces or surfaces other than fair face of brick work as on wall surfaces and finish the surface even and fair. Using Water proofing compound @ 3% by weight of cement (WPC shall be measured and paid separately).

Supply only integral water proofing compound.

M&L rendering 10mm thick, plaster on fair faces of brick work or stone masonry or concrete surfaces in CM 1:6 including finished surfaces fair and even complete all as specifed and directed.

M&L 40mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in floor complete all as specifed and directed.

Supply only glass dividing strips 3 mm thick and 38 mm width complete all as specifed and directed.

M&L 5mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L 25mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as in bedding layer of floor finished the surface even and rough complete all as specified and directed.

M&L coloured non skid ceramic tiles (1st quality) 7 to 8mm thick area of each tile exceeding 0.11Sqm but not exceeding 0.18 Sqm, as in floors etc, laid over with and including 15mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per item No 16.00 above but in skirting over with and including 10mm thick plaster in CM (1:4) including necessary cutting of tiles as required size all as specified and as directed.

M&L coloured non skid ceramic tiles (1st quality) 7 to 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm as in floors etc, laid over with and including 15mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per item No 18.00 above but on vertical surface with and including 10mm thick rendering in CM (1:4).

M&L coloured non skid ceramic tiles (1st quality) 7 to 8mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc., laid over with and including 15mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L glazed ceramic tiles (1st quality) (coloured) 300mm x 200mm x 7mm thick on vertical surfaces such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 10mm thick rendering in CM (1:4) complete all as specified and as directed.

M&L glazed ceramic coloured tiles (1st quality) in vertical surface 450mm x 300mm x 7-8 mm thick joint free set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement slurry base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L kota stone slab 10-15 mm thick in riser step, skirting, dado etc with and including 10mm thick rendering in CM (1:4) complete all as specified and as directed.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete all as specified and as directed.

M&L 16-18mm thick Granite black colour (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform, staircase treads and like jointed over and including 15mm thick screed in cement mortar (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, compltee all as specified.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4.00 Sqm each.

S&F mild steel framed work such as grills, gratings, etc using angle iron, flat iron, round bars with end of bars shouldered and or rivetted or forged into spikes, framed guard bars barred into iron doors, walk ways railing frame work amd similler work confiming to Fe 290, GDE E-165 all as specified and directed.

S&F 35mm thick, factory made panelled door shutter (two panel), plain, framed with 2nd class hard wood lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS-1003 (Part I), kiln seasoned and chemically pressure treated complete as specified and directed.

S&F 35mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc complete as specified and directed sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 10mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast complete all as specified and directed. (SS Butt Hings shall be paid seperately supply only).

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F stainless steel butt hinges, 100mm medium weight and fixed all as directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section Supply and fix complete as specified and directed.

S&F 150mm extruded aluminium alloy handles, fabricated type, anodised complete as specified and directed.

S&F mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia, 300mm long, with and including a minimum of 6 bolts and nut, four on bolt plate and two on staple plate and fixed complete as specified and directed.

S&F door spring with 300mm mild steel rat tail rod pattern of standard quality including roller and roller plate complete helical spring) complete as specified and directed.

M&L including preparation of new or previously untreated wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on wood or wooden based surface exc 10cm width or girth complete all as specified and directed.

M&L preparing new surfaces plastered or unplastered on walls etc & applying two coats of distemper oil emulsion over a layer of chalk whiting preparatory to distempering complete all as specified & directed.

M&L preparing new surfaces plastered or unplastered on walls etc & applying two coats of cement base paint over primer with alkali- resistant primering paint complete all as specified & directed.

M&L preparing newly plastered surfaces & applying three coats of white wash on walls complete all as specified & directed.

M&L preparing plastered or unplastered new surfaces of ceiling & applying three coats white wash complete all as specified & directed.

Complete removal of existing treatment & preparation of old surfaces by washing rubbing down and stopping of plastered surfaces and applying two coats of Cement based paint white or tined on walls including over a one coat of alkali-resistant priming paint complete all as specified and directed.

M&L preparation of old treated surfaces of walls, plastered or unplastered and applying one coat of cement base paint of approved shade/tint. complete all as specified and as directed.

M&L preparing surfaces plastered or unplastered old surfaces of ceilings and applying one coat of white wash complete all as specified & directed.

M&L brooming down old decorated surfaces of walls, plastered or unplastered including cornices, plasters etc and applying one coats of white wash complete all as specified and as directed.

All as per description of serial item No 47.00 here-in-above but on ceiling surfaces.

M&L brooming down old decorated surfaces of walls, plastered or unplastered including cornices, plasters etc and applying one coat of oil bound distemper of approved shade/tint complete all as specified and as directed.

M&L preparation of old wall surfaces by washing rubbing down and stopping of distempered surfaces and applying one coat of distemper oil emulsion white or tined on walls including cornices etc complete all as specified and directed.

Hacking out old broken glass of any thickness/size & any description from wooden or steel frame fixed with clips/putty/wooden beading and S&F with 3mm thick ordinary sheet glass fixed with clips and oil putty/wooden beading completed in squares not exc 0.50 Sqm each pane all as specified and as directed.

All as per item No 51.00 above but 3mm thick figured glass, pin head type.

Hacking out old broken glass of any thickness/size & any description from wooden or steel frame fixed with clips/putty/wooden beading and S&F with 4mm thick ordinary sheet glass fixed with clips and oil putty/wooden beading completed in squares not exc 0.50 Sqm each pane all as specified and as directed.

All as per item No 53.00 above but 4mm thick figured glass, pin head type.

Hacking out old broken glass from metal/aluminium frame incl punching or drilling out old glazing pins/springs/clips/ beading and providing & fixing new of any thickness/size of any description and S&F 5.5 mm thick sheet glass, ordinary quality and glazing in square exc 0.5 sqm in each pane complete all as specified.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed tinned tacks or GI wire stampe or nails and screws/wooden beading complete all as specified & directed.

S&F in repair 18/19mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified & directed.

S&F in repair MS drapery rod 19/20 mm dia fancy type with PVC coloured sleeves fixed with suitable brackets two Nos & PVC colour bowl two Nos at end for door/window complete all as directed.

S&F in repair SS Curtain rod 19/20mm dia as including suitable fancy type brackets fixed wity rawl plug, screw etc complete all as specified.

S&F in repair door closer hydraulically regulated, designation No 3, aluminium (Die cast) body, universal type (ISI marked) complete all as specified & as directed.

S&F in repair brass mortice lock, vertical type, size 65mm, 2 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified.

S&F in repair MS helical door spring 300 mm size with roller & roller plate fixed to wooden or steel frames with Screws/welding as required at site complete all as specified.

S&F in repair 300mm long aluminium alloy anodised sliding door bolt with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium and fixed all as spd.

S&F in repair extruded aluminium alloy handle, fabricated type, anodised, 125mm size (ISI marked) complete all as specified.

S&F as in repair 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified.

S&F in repair butt hinges 100 mm long medium weight cold rolled MS fixed to wooden or pressed steel/angle iron frames by welding all as specified.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed overall length 140 mm complete all as specified & directed.

S&F in repair MS steel window stay 300 mm long for steel windows all as specified and directed.

S&F in repair handles for steel windows all as specified and directed.

Welding in repair not exceeding 6mm thick and not exceeding 2.5 cm in length all as specified and directed.

Taking down shutter of any description not exc 1 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 15mm complete all as directed.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 15mm dia.

S&F 15mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 20mm complete all as directed.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 20mm dia.

S&F 20mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 25mm bore pipe complete as specified and directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 25mm dia complete to walls and ceiling or laid in floors of 25mm bore complete as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantling existing water tanks complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantling existing water tanks complete all as specified and directed.

S&F in repair ball valves of 20mm dia, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed, minimum weight 210 gms any type complete all as directed.

S&F in repairs vitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repair vitreous china squatting pan 'orissa pattern' size 580 x 450mm white with integral foot rest (ISI marked) with 'P' or 'S' trap, front or back inlet and foot rest any pattern, including connection to flushing pipe anti-syphonage pipe etc including setting of pan & trap in lean PCC 1:5:10 complete and making good to distrubed floor with PCC or cement mortar 1:3 to match with sorroundings all as directed.

S&F in repair vitreous china wash basin white of size 550x400 mm with padestal stand (ISI marked) including 32 mm CP waste coupling & PVC flexible waste pipe of min 90 cm long, flat back or angle back type excluding taps, waste chain & plug but incuding cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair jet spray PVC butterfly plated for EWC with & including PVC connection 600 mm long suitable for 15mm bore GI pipe with PTMT nut & nipple complete.

S&F in repair health faucet chromium plated suitable for 15 mm bore pipe including 1mtr long PVC tubes for EWC complete all as specified & directed.

S&F in repair PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, complete all as specified.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as directed.

S&F in repair PVC internal fittings (kit) complete for low level flushing cistern tank all as specified and directed.

S&F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed.

S&F in repair CP toilet paper holder with cover complete all as specified and directed.

S&F in repair waste coupling 32mm of PTMT (half or full threaded) (minimum wt 45 gms complete all as specified & directed.

S&F in repair waste coupling 40mm of PTMT (half or full threaded) (minimum wt 60 gms complete all as specified & directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed.

S&F in repair brass spindles, phases of brass of any size required 3/4/5 for bib taps, pillar cocks, stop cocks, angle valves concealed valves complete all as directed.

S&F in repair MS grating CP 75/100mm dia, with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed.

S&F in repair 15mm bore pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly nuts, screwed for iron pipe etc complete as specified and directed.

S&F in repair brass chromium plated shower rose with long arm 150mm size fixed to 15mm bore pipe all as directed.

S&F in repair sink with drainage board made out of stainless steel 1mm thick sheet for kitchen with plug, washers, waste pipe, cast iron centilever bracket, connecting union over all minimum size 915mm x 460mm with bowl size 410mm x 330mm x 160mm incl 32mm PVC flexible waste pipe complete all as directed.

S&F in repair sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or incluidng fixing contilever brackets and connecting union to pipe over all size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as directed.

S&F in repair waste coupling for sink as per sample approved complete all as directed.

S&F in repair mirror cabinet (PTMT) fixed on wall with cadmium plated brass screws as per approved by GE all as directed.

S&F in repair bib taps bore of pipe in 15mm, cast copper alloy, fancy type, chromium plated, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair bib taps bore of pipe in 15mm, cast copper alloy, chromium plated, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs for bib tap standard of PTMT any colour 15mm bore high pressure screwed for iron pipe (Min. wt 90 gms) and complete all as specified and directed.

M&L repair to existing 15 mm bore bib tap/stop cock/angle valve etc cast copper alloy chromium plated by replacing brass jumper assembly with spindle(brass tee/elbow for MAP qtr) PVC washer etc complete all as directed. Note : (i) Contractor or his authorised representative collect such type of complaints from B/R-I complaint cell at 9.00 AM on daily basis except sunday /Holiday. No extra payment shall be made on account of collection of complaint.

M&L repair to existing 15 mm bore bib tap/stop cock etc cast copper alloy by replacing brass jumper assembly PVC washer etc matching with existing complete all as directed. Note : (i) Contractor or his authorised representative collect such type of complaints from B/R - I complaint cell at 9.00 AM on daily basis except sunday /Holiday. No extra payment shall be made on account of collection of complaint.

S&F in repair 15mm bore, stop valve/angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repair 15 mm bore stop cock with crutch or butterfly handle, screwed down high pressure , screwed both ends for iron pipe or for union complete as specified and directed.

S&F in repair CP wall mixture for hot & cold water screwed down for iron pipe and fixed bore of pipe 15 mm complete as specified and directed.

S&F in repair 15mm bore, two way angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in reapir 15mm bore, stop valve external threaded, chromium plated, fancy type, with long shank, and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repair 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed.

S&F in repair PVC flexible waste pipe 32/40 mm dia & approx 900 mm long with PVC waste coupling suitable for WHB, sink & urinal complete all as specified & directed.

S&F in repair brass CP wall mixer for mixing hot & cold water suitable for 15mm bore dia pipe screwed down for iron pipe and fixed copmplete all as specified and directed.

Dismantling AC pipe/ PVC pipes 110mm/ 75 mm dia complete as specified and directed.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with MS clamps as per site requirement complete all as directed.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints laid in trenches or floors complete all as directed.

S&F PVC (SWR) Vent cowl 75mm dia complete all as directed.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors complete all as directed.

All as per item No 125.00 here in before but fixed to walls with clamps complete all as directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F PVC (SWR) 75mm dia floor trap, plain with grating including jointing with solvent cement all as directed.

S&F in repair PVC (SWR) junction single (single T) of 110mm bore with access door complete as specified and directed.

S&F in repair PVC (SWR) branch piece single (Single Y) of 75mm bore equal or unequal complete as specified and directed.

S&F in repair PVC (SWR) bend 110 mm bore of any radius complete as specified and directed.

S&F in repair PVC (SWR) vent cowl of 110 mm bore complete as specified and directed.

S&F PVC (SWR) gully trap 125/110mm, setting and jointed with solvent cement complete as specified and directed.

S&F in repair MS clamps fixed to walls on both sides of pipes with plastic raw plugs and 50mm size steel screws complete as specified and directed.

S&F in repair PVC (SWR) bend 75mm bore of any radius with access door complete as specified and directed.

Treatement for sunken portion as per following course of activities :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed. (iii) M&L water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement. (WPC will be measured and paid seperately). (iv) M&L applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L PCC 1:7:12 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (vi) M&L PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @ 2% by wt. of cement, as sub base, 75mm thick. (WPC will be measured and paid separately) (vii) M&L plastering in CM 1:4, 15 mm thick with water proofing compound at the rate of 2% by weight of cement and finishing the surface seven and fair.(WPC will be measured and paid seperately). Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect. (b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated. (c) Horizontal flat area to be measered.

Dismantling Asbestos Cement Corrugated or Semicorrugated in Roof covering complete as specified and directed.

Demolition of reinforced cement concrete of any description and in any position (reinforced cut as required to facilitate demolition) complete as specified and directed.

S&F steel work in tubular section for purlin/rafters etc including special shaped washer etc. complete using induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240. complete as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

Dismantling posts, purlins, or any part of truss, struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground or wall complete as specified and directed.

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws as specified.

Cutting holes in brick walls Exc half brick but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar etc for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

M&L providing cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) as in copings complete as specified and directed.

M&L heavy duty coloured exterior grade tile of size 300mm x 300mm x 10mm thick as in floor ,set and jointed in neat cement slurry and pointed in white cement mixed with approved pigment to match the shade of tiles over with and including bedding layer of 15mm thick of CM (1:6) complete all as specified.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) on in sub base of floor complete as specified and directed.

Cutting channels, grooves or rebates n exc 15cm girth, in concrete/brick walls/stone walls and trimming surface, inserting GI sheet into the groove as directed.

M&L pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws as specified.

S&F in repair screwable plastic lid cover with frame fixed with screws, nut and bolts for existing 500 litre capacity rotational moulded polyethylene water storage tanks cylindrical vertical complete all as specified and as directed

S&F in repair screwable plastic lid cover with frame fixed with screws, nut and bolts for existing 1000 litre capacity rotational moulded polyethylene water storage tanks cylindrical vertical complete all as specified and as directed.

S&F in repair waste fitting 32 mm bore, brass, chromium plated for glazed ware sink, basin with long screwed shanks and fly nuts, flange end bedded in red lead and other end fixed complete as specified and directed.

S&F in repair waste fitting 40mm bore, brass, chromium plated for glazed ware sink, basin with long screwed shanks and fly nuts, flange end bedded in red lead and other end fixed complete as specified and directed.

S&F in repair jet spray chromium plated brass for EWC with and including PVC connection 600 mm long and one CP socket 25 mm long suitable for 15mm bore GI pipe complete as specified and directed.

S&F in repair 15mm bore angle valve chromium plated screwed down high pressure with capstan head screwed both end concealed type for iron pipe or for union complete as specified and directed.

Dismantling or taking up or down PVC pipes and connection from wall/ceilings/floors etc of 15mm bore complete as specified and directed.

Dismantling or taking up or down PVC pipes and connection from wall/ceilings/floors etc of 20mm bore complete as specified and directed.

S&F 1216 (Out side dia - 16mm) Polyethylene - Aluminium Polyethylene (PE-AL-PE) composite pressure pipes including all crimp type internal sealing Plastic metal composite fittings (such as elbows, tees, reducers) complete as specified and directed.

S&F 1620 (Out side dia 20mm) Polyethylene - Aluminium Polyethylene (PE-AL-PE) composite pressure pipes including all crimp type internal sealing Plastic metal composite fittings (such as elbows, tees, reducers) complete as specified and directed.

S&F in repair WHB flat back of size 580mm x 450mm excluding taps waste chain plug stopper but incl brackets incl waste pipe cutting pinning in ends of brackets complete.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plugs & cadmium plated brass screws complete all as directed.

S&F in repair glass corner shelf assembly 300mm long toughed glass minimum thickness of the 5.5 mm, with SS pipe railing fixed to wall by means of brass screws and raw plugs complete as specified and directed.

S&F in repair stainless steel peg stay of six nos fixed to wall by means of brass screws and raw plugs complete as specified and directed.

S&F in repair bottle trap of PTMT for wash hand basin having minimum water seal of 25 mm (minimum weight 260 gms) and bore of discharge pipe 32mm complete as specified and directed.

S&F in repair bottle trap of chromium plated for wash hand basin having minimum water seal of 25 mm and bore of discharge pipe 32 mm complete as specified and directed.

Taking down Steel window/Ventilators not exceeding 1.5(without taking off shutter from frame including guard bars) any description.

Taking down steel window/ventilators exceeding 1.5 sqm but not exc 4 Sqm (without taking off shutter from frame including guard bars) any description.

S&F extruded aluminum alloy with galavanisied mild steel hing pin butt hinges 100mm long complete as specified and directed.

S&F factory made steel window with side hung shutter and box type hinges steel handle and steel peg stay with glazing bars dovetailed or welded complete as specified and directed.

All as per item No 169.00 above but without glazing bars.

S&F factory made steel ventilator with top hung shutter with glazing bars including hings,steel peg stay etc complete as specified and directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintel hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps,plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete as specified and directed.

M&L preparation to new or previously untreated steel surface of any description,over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of zinc chromate primer complete as specified and directed.

M&L 50mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection course surfaces finished even and smooth without using extra cementcomplete as specified and directed.

M&L 20mm thick granite (of any type) tiles machine cut, bedding and jointing with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointing with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with and including 10mm thick rendering in CM 1:4 for recieving stone etc complete all as specified and as directed.

Taking down bib taps, stop cock, shower rose etc and removing blockages or air lock from GI/PVC tubing 15/20/25 mm dia by applying pressure through suitable pressure pumps/ using acid/chemical to clear any blockage and refixing bib tasp, stop cocks, shower rose etc. Note : (i) Contractor or his authorised representative collect such type of complaints from B/R - I complaint cell at 9.00 AM on daily basis except sunday /Holiday. No extra payment shall be made on account of collection of complaint.

M&L running welding in repairs, thickness of metal to be welded not exc 6mm all as specified & directed.

M&L running welding in repairs, thickness of metal to be welded exc 6mm but not exc 9mm all as specified & directed.

S&F in repair CI pipe sand cast 100mm dia fixed to walls/or floors any length with or without ears with cement joints all as specified & directed.

S&F in repair CI pipe sand cast 75mm dia fixed to walls/or floors any length with or without ears with cement joints all as specified & directed.

S&F in repairs CI branch pieces single equal or unequal ordinary or inverted or with oval access door paralled branch 100mm bore complete as specified and directed.

S&F in repairs CI branch pieces single equal or unequal ordinary or inverted or with oval access door paralled branch 75 mm bore complete as specified and directed.

S&F in repairs of CI bend of any radious, diminishing piece or tapers (Larger bore measured) 75 mm bore complete as specified and directed.

S&F in repairs of CI bend of any radious, diminishing piece or tapers (Larger bore measured) 100 mm bore complete as specified and directed.

S&F in repairs cast iron nahani trap 75 mm bore jointing to waste pipe fixed in cement concrete type B-1, 1:2:4 complete as specified and directed.

S&F in repair cast iron 'P' or 'S' trap 100 mm bore of pipe in cement concrete type B-1, 1:2:4 complete as specified and directed.

S&F in repair PVC (SWR) 'P' trap 110/110 mm bore complete as specified and directed.

M&L reinforcement cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) in slabs supported on walls beams and columns in floors, roofs, shelves and like. Note : Reinforcement & form work shall be measured and paid for separately.

M&L form work to soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work not exc 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete as specified and directed.

Form work to edges of concrete flats, roofs, floor slabs, landings and similar work, not exc 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of conccrete complete as specified and directed.

M&L reinforcement TMT bars 10mm dia overcut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in cills, coping steps, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and alike including weathering, slightly rounded or chemfered angle and throating as directed.

M&L providing sand stone 5cm thick as in sun shed, chajjas, sheleves etc set and pointed in cement mortar 1:4 complete all as specifed and directed.

M&L for cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipe etc complete all as specified and directed by Engineer-in-Charge for exc 250 but not exc 500 ltr capacity.

M&L for cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipe etc complete all as specified and directed by Engineer-in-Charge for exc 500 but not exc 1000 ltr capacity.

M/s S Amarjit Singh

J.J.ENGINEERING