SPECIAL REPAIR ROOF FALSE CEILING REWIRING OF BLDG NO T 35 OF SHO AND SPECIAL REPAIR TO BLDG NO P 23 OF DET CENTRAL COMD INT BN UNDER AGE BR II OF GE W AGRA

Amount

Taking down wooden roof truss exc 4 m but not exc 8 m span, coupled rafters or trussed beams all as specified and directed

Dismantling timber scantlings, in framed work, 40 Sq.cm and over in section and in any position complete all as specified & directed.

M&L roof truss (framed trussed, purlins, crane gantries, rails and fasterning including distnace pieces cleats etc confirming to Fe-290 grade E-165 complete all as specified & directed.

S&F rolled section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc confirming to Fe290 grade E-165 complete all as specified & directed.

Dismantling cement (corrugated or semicorrugated, etc) sheets in roof covering including L type or J type hooks or cranked bolts etc complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet for ridges 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillar etc.complete all as specified & directed.

M&L brick work (old Size) in cm (1:6) straight or curved on plan exceeding 6.00 mtr mean radius complete all as specified & directed.

Demolation of reinforced cement concrete roof, floor (other than ground floor) beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M&L reinforced cement concrete (nominal mix) 1:2:4, type B-1 (using 20mm graded stone aggregate) in beam/band and the like complete all as specified & directed.

M&L reinforced cement concrete (nominal mix) 1:2:4, type B-1 (using 20mm graded stone aggregate) in slab supported on walls and the like complete all as specified & directed.

M&L for TMT bars of 10mm dia and over, dia cut to length bent to shape required including cranking bending spirally, hooking ends and binding with mild steel wire not less than 0.9 mm dia (annealed) complete all as specified and directed.

M&L for Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with, in stirrups and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Use & waste of formwork to side and soffits of beam etc rough finished surfaces of concrete all as specified and directed.

Use & waste of formwork to side and soffits of shelves etc rough finished surfaces of concrete all as specified and directed.

Taking down cement plaster on brick or stone walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

M&L for rendering 15mm thick on any faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:4 with water proofing compound as per manufacturers's instructions, on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth complete all as specified and directed. Note : WPC will be measured & paid separately.

M&L for preparation of new plastered or un-plastered surfaces of wall and applying two coats of cement base paint over a coat of priming paint complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) bed plates and the like including weathering slightly rounded or chamfered angles and throating including necessary use & waste of form work complete all as specified and directed.

M&L preparation of new plastered or un-plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered or un-plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L preparation of new plastered or un-plastered surfaces of wall and applying two coats of oil emulsion distemper over 2 mm thick plaster of paris putty complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Roughening of surface of old concrete floor by picking, sweeping, clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for non skid ceramic colour tiles joint free 7 to 8 mm thick (Square /rectangle) area of each tile excedding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and ponted in white or coloured cement to match including 15 mm thick scread bed in cm 1:6. complete all as specified and directed.

All as per item No-27 but on verticle surfaces such as skirting/dado including 10 mm thich rendering in cm 1:4.

M&L for glazed ceramic coloured tile 350x250x7mm / 450x350x7mm thick jointed and pointed with white or coloured cement including 10 mm thick rendering in cm 1:4 complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with out glazing bars, dovetailed or welded complete all as specified and directed.

S & F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, guard bars etc, with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 410 complete all as specified & directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for 3 mm thick figured glass,pin head type and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F soild PVC door frame of size 50mm x 47mm made out of 5 mm plain coloured PVC sheet, reinforced with MS square tube supplying and fixing in opening complete all as specified and directed.

S&F factory made solid PVC moulded door shutter 28 to 30 mm thick(stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site as per specifications & drawings shown in section 8 of SSR Part II complete all as directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) exc 1.5 Sqm and not exc 4.00 Sqm each complete all as specified and directed.

Mild steel farmed work as in doors (as in ckowkats) or gates of angle or other section with guest plates rail, brasses rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Gde Fe-290 including shop coat of red oxide including prepration of surface before fixing complete all as specified and directed.

S&F 35 mm thick 2nd class plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commericial face veneers: supplied and fitted to chowkats, complete all as specified and directed.

S&F 30 mm thick 2nd class hard wood glazed and skeleton shutters, for window and vantilator open rebated and prepared to received glass gauze etc but divided into squares, with plain chamfered or rounded mitred and rebated sash brs any numbers and mitred beds for securing glass, but divided into squared any number etc sizes of members of shutters as specified in SSR Part I, section 8 clause 8.24(a) supplied and fitted to chowkats all as specified and directed.

S & F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

S&F in repair stainless steel curtain rod 25mm dia with 2mm web thickness including brackets, side knob and 8 Nos stainless steel curtain rings per meter lenth all as specified and directed.

S&F in repair 300 mm MS ordinary rat tail spring including roller and roller plate complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed (Size of hinges in 100 mm) complete all as specified and directed.

S&F 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long alluminium handles, cast type, anodized and fixed complete all as specified and directed.

S & F alunimium sliding door bolt 300 mm long stove enamealled black with bright bolt not less than 16 mm dia with and including and minimum of 6 boalts and nuts four on bolt plat and two on staple plate and fixed etc.

S&F 18/19 mm thick block board, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face veneer on one face, fixed with screws to timber frame work complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) 30mm all as specified and directed.

M&L for 1st class hard wood plain cover fillets square, rectangular or triangular in section bull nosed, splayed chamfered or rounded on one edge or face sectional area not exc. 6 Sqcm complete all as specified and directed.

S&F in repair stainless steel plate rack made out of 1mm thick sheet of grade 304, three shelves, of size 750 x 600 x 230 mm fixed to wall complete all as specified and as directed.

S&F in repair kitchen stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495.mm x420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F brass cup board lock 75mm size 4 levers, grade-1 with duplicate keys complete all as specified and directed.

S&F stainless steel magnetic catcher 2” suitable for CB / cabinet shutters all as specified.

S&F brass handles extruded fabricated type, 125mm size complete all as specified and directed.

Taking up or down 20 mm bore dia steel tubing and connections, including removal to store/ site complete all as specified and directed.

Taking up or down 15 mm bore dia steel tubing and connections, including removal to store/ site complete all as specified and directed.

S&F 15mm dia tubes medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F tubes `medium grade' galvanised with all fittings and fixed complete to wall 20mm bore complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to encs or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing etc and making good sutting not exc 10 cm in girth in brick wall all as specified and directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern white (excluding fixing bolt flushing cistern and flush pipe) fixed in repairs complete with seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminum hinging device complete all as spfd and directed.

S&F in repairs low level flushing cistern of capacity 10 litre ISI marked complete with inlet ball valve, and handle including bracket of Commander/Hindware/ complete all as specified and directed.

S&F in repair CP Bib taps fancy type cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe) complete all as specified and directed.

S&F in repair chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S & F in repair CP Stop valves fancy type (angle valve) cast copper alloy screwed down high pre-ssure with crutch or but terfly handle screwed both ends for iron pipe or for unions and fixed ( 15mm bore dia of pipe ) complete all as specified and directed.

S&F in repairs brass CP mixer (wash basin /wall )15 mm bore for mixing hot & cold water screwed down for iron pipe or any type of pipe and fixed in position and making good disturbed portion complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe complete all as specified and directed.

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair shelf PTMT fixed with and incl CP brass screw and wooden / plastic cleats ( min wt 300 gm) complete all as specified and directed.

M&L in repair gun metal, globe or gate valve 20 mm with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs Vitreous China wash hand basin white flat back size 550x400mm including brackets, waste pipe, complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks with cover & 20mm ball valves high pressure of PTMT with epooxy coated aluminium road & high density plastic ball (cylindrical vertical with closed top) hoisted and fixed in position incl disconecting of existing tank all as specified in SSR Part I (Capacity in litres 500) complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) type'A' Soil waste, rain water pipe and vent pipes single socketed in any length with rubber ring joints fixed to walls including making good disturbe portion to match the existing complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bends of any radius with access door including making good disturbe portion to match the existing complete all as specified and directed.

S & F in repair 110 mm bore dia PVC (SWR), type'A' pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F in repair 75mm bore dia PVC (SWR),type 'A' pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F in repair PVC (SWR) bend any radious of 75 mm dia complete all as specified and directed.

S & F in repair PVC (SWR) Junction (Single 'T' ) equal or un equal of 75 mm dia complete all as specified and directed

M & L in repair PVC (SWR) gully traps125/110 mm setting and jointing with solvent cement complete all as specified and directed.

S & Fin repair PVC (SWR) Vent Cowl 75 mm dia complete all as specified and directed.

S&F in repairs 75 mm dia of outlet CI floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

S&F in repair 125mm PTMT Grating with waste hole minimum weight 40 gm complete all as specified and directed.

M&L 20mm thick granite (of any type) slab machine cut, in skirting/ dedo laid over cement screed and jointed with grey cement cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L PCC 50 mm thick (1:3:6), type C-1 (using 20 mm graded stone aggregate) as in plinth protection complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Dismantling wall and ceiling boards( fibre pulp, insulation etc.) or insulation board /slabs/blanket any thickness including cover fillets complete all as specified and directed.

S & F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre complete all as specified and directed.

M&L for 4 mm thick non asbestos fibre cement building designer boards fixed in ceiling or laid/inserted to timber / GI / aluminun frame complete all as specified and directed.

Taking down of old precast interlocking paver block any size and shape any description and in any position and through at low level with in cantt area complete all as specified and directed..

M&L for 80 mm thick precast PCC interlocking coloured paver rubber moulded block factory made of grade M 40 single layer monolithic high density manufactured by electro vibro hydraulically operated block making maching conforming to IS -15658- 2006 laid and jointed over sand cushion layer with grey cement and pigment complete all as specified and directed. Note : Sand cusion shall be measured & paid separately

M&L for PCC 1:5:10, type D-2 (using 40mm graded crushed stone aggregate) as in sub base and mass concrete complete all as specified and directed.

M&L for 25 mm thick sand cushion layer for laying interlocking pavers complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including complete all as specified and directed.

M&L in repair machine pressed coloured chequered tiles 25 cm x 25 cm x 25 mm thick set, jointed & pointed in grey cement with pigment including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B1 (20 mm graded stone aggregate) as in sub base complete all as specified and directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc by cement/ colour /plaster to match with the existing location spot complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC FRLS insulated, unsheathed, single core, multi stranded copper conductor cable 1100 volts grade including 1.5sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and including rigid PVC conduit of suitable size but not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0 mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for the one light/ fan/street/bell point controlled by 1 one way switch 5/6 Amps complete all as specified & directed.

All as per item No-103 here in before but One socket outlet 5/6 Amps on independent bd controlled by one switch complete all as specified & directed.

All as per item No-103 here in before but One socket outlet 5/6 Amps controlled by one switch on same board with other switches complete all as specified & directed.

All as per item No-103 here in before but one socket out let 3/5 pin, 5/6 Amps controlled by 1 one way switch on independent board but below the switch board of light points in same vertical plane complete all as specified & directed.

All as per item No-103 here in before but using 2.5 sqmm PVC FRLS insulated stranded copper cunductor cable and for one socket out let 3/6 pin, 15/16 Amps controlled by one 1 way switch on independent board complete all as specified & directed. NOTE-For item no 103 to 107-: (i)The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillers etc for concealing the conduits to required depth & making good the disturbed surfaces in cement mortar 1:4 including finishing the surface to match with the existing surface.The portion of point wiring at RCC Coloumns/Beams/Ceilings etc shall be in surface conduit of suitable size fixed on surface with using PVC rawl plug and provision of covering terminal boxes/junction boxes of any shape and size with 3 mm thick bakelight laminated sheet fixed with suitable GI screws and cup washers. (ii) Fittings like switches, sockets, regulators, lamp holders, light foittings shall be measured and paid for separately under appropriate item of schedule A. (iii)The size of conduits shall be determined on permissible no of runs of wires as specified in SSR part-I clause 19.125 (B).However minimum size of conduit shall be 20 mm dia (medium grade)

Supply and fix switch piano, flush type, single pole, 5/6 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.38058 or equivalent as approved by GE.

Supply and fix switch piano, flush type, single pole, 15/16 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.39991 or equivalent as approved by GE.

Supply and fix socket outlet, 5/6 Amps, flush type, 5 pin 230 volts complete all as specified and directed. Make: Anchor Cat No.38320 or equivalent as approved by GE.

S&F switch, bell push button, single pole, 5/6 Amps, one way, 230 Volts complete all as specified and directed. Make -Anchor CAT Part No-38047 or equivalent as approved by GE.

Supply and fix socket outlet, multi-purpose 3 pin 5/6 Amps and 3 pin 15/16 Amps complete all as specified and directed. Make: Anchor Cat No.39994 or equivalent as approved by GE.

S&F for ceiling rose surface bakelite 62.5 x 25 mm size 3 terminals complete all as specified and directed. Make -Anchor CAT Part No-39072 or equivalent as approved by GE.

Supply and fix lamp holder insulated body with back plate for batten fitting complete all as specified and directed. Make: Anchor Cat No. 39797/ 39800 or equivalent as approved by GE.

Supply & fix rotory stepped type electronic fan regulator mini flush type 100 watt 230 Volts complete all as specified & directed. Make: Anchor Cat No.38284/38660 or equivalent as approved by GE.

Supply and fix electrical bell model city ding dong (Ding dong type) AC, 230 Volts complete all as specified & directed. Make:- Anchor / Cona / Plaza as approved by GE.

Supply and fixing LED Bulb 15 watt, single phase, 230 Volts AC supply suitable for lamp holder complete all as specified and directed. Make :- Havells cat part No-LHLDDEEEML8R015 or equivalent Model of Philips/Bajaj/CG/ Wipro as approved by GE.

Supply & fix surface/wall mounting LED batten 20 watt luminaire having extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with mounting accessories complete with lamp holders fixed to wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No-ENDURALINEARNEOBS20WLED865SPCWH or equivalent Model of Philips/Bajaj/CG as approved by GE.

Supply & fix, surface/ ceiling mounting type 34 watt LED luminaire PLUTO NEO PENAL 2X2 environmental friendly new generation aesthetically ultra modern recess mounting with high brightness SMD LEDs as light source with reflector cover electronic driver, connector block etc with internally prewired fixed to ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- PLR34WLED857S or equivalent model of make, Philips/Bajaj/ Crompton Greaves as approved by GE.

Supply & fix, outdoor security light LED 36/40 watt luminaire IP 65/66 protection polyster powder coated with pressure die cast aluminium housing and robust construction with reflector cover pre anodised and flat white high transmission acrylic cover or toughened glass, natural white type with electronic driver, connector block etc with internally prewired fixed to building with and including 1.20M long bracket made out of 40mm dia light grade GI pipe bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/MS clamps & 12mm dia bolts, nuts & washers etc and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- ENDURAPEARLNEOSL40WLED757PASYTOPC,Phillips cat part no BRP052 LED 036 CW HP SLA FG S1 PSU GR or equivalent as approved by GE.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make:- Havells cat part No- LHECDEFOIH1W028 or equivalent model of make ,Philips/Bajaj/ Crompton Greaves as approved by GE.

Supply & fix surface mounting type bulkhead 10 watt LED luminaire with reflector cover electronic driver, connector block etc with internally prewired fixed to wall with fixing accessories and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- Cat part No FT10WLED857SSYMBOPC or equivalent model of make Philips/ Bajaj/ Crompton Greaves as approved by GE.

Supply & fix in replacement, single pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB SP of capacity 20 Amps 240 volts IK-08 As per IEC 61439-3 complete all as specified & directed. Make:- Legrand cat part No- 5078 11 & 408593 or equivalent model of make Siemens/ Schneider as approved by GE.

Taking down distribution boards any size any type including MCCB/MCB TPN/SPN/SP/Isolator etc and making good the disturbed surfaces complete all as specified and directed.

Supply and fix MCB DB vertical type 4 way VTPN sheet metal enclosure 415 volts with 100 Amp fully insulated standard copper bus bar for each face & surrounded with neutral bars and two common neutral bar, two earth bar including cable ties for cable manegement suitable for housing MCCB TPN 415 Volts as incommer, IP-43, IK-09 as per IEC 61439-3 with metal doors all enclosed on standard steel sheet flush mouting type double door factory fabricated complete without MCB & MCCB but with enclosue blank plate complete all as specified and directed . Make:- Legrand CAT No.5077 25 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply and fix MCB DB 4 way sheet metal enclosure triple pole and neutral 415 volts with 100 Amp standard copper bus bar IP-43, IK-09 with metal doors of suitable size and common neutral link and earth bar all enclosed on standard steel sheet flush mouting type double door factory fabricated complete as per IEC 61439-3 without MCB but with enclosue blank plate complete all as specified and directed . Make:- Legrand CAT No.5076 70 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply and fix MCB DB sheet metal enclosure factory fabricated double door SPN 8 way with 100 amps rated copper bus bar 240 volts IP-43, IK-09 with metal doors complete all as specified and directed. Make:- Legrand Cat Part No. 5076 11 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply and fix MCCB 4 pole 100 to 125 Amp Icu 16 Kilo Amp and Ics 100% of Icu with adjustable 70% to 100% and thermal magnetic release suitable for fixing in VTPN DB. Make : Legrand cat part 4200 15 to 4200 16 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply & fix Isolator TPN, 4 Pole, 415 Volts, 50 Hz AC Supply , 100 Amps, IP-20 as per IEC 60947-3 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4065 22 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply & fix Isolator SPN , 40 Amps, 240 volts, 50Hz, IP-20 as per IEC 60947-3 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 406501 or equivalent model of make ABB/ L&T/ Schneider as approved by GE.

Supply & fix MCB SP, 40 to 63 Amps, 'C' Curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4085 96 to 4085 98 or equivalent model of make Siemens/ Schneider as approved by GE.

Supply & fix MCB SP, 6 to 32 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. Make:- Legrand CAT No. 4085 87 to 4085 95 or equivalent model of make Siemens/ Schneider as approved by GE.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor .

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed.Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 2.5 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed.Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 2.5 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

M & L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

M&L for electrically disconnecting and taking down existing ceiling/Exhaust fans from any hight or in any position from existing bldg and keeping in safe custody for reuse at site after necessary repare/ servicing & painting with one coat of synthetic enable paint and writing of MES/identification No. of fans and re hanging/ re-fixing in original position but including replacement of three cor flexible copper conductor cable from ceiling rose to fan connector block of soze 0.75 Sqmm and hanging fan clamps, nuts, bolts and rubber reel bush etc & testing for proper functioning complete all as directed.

Supply & Laying,testing ,cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 16 Sqmm 4 core compele all as specified and as directed.

Supply & Laying,testing, cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 25 Sqmm 4 core compele all as specified and as directed.

Supply and fixing GI Pipe 40 mm Light grade, for cable protection laid in trench under road or path or fixed on pole or wall with clamps with all fittings complete all as specified.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep in soft/loose/ soil for taking out/laying CI/GI pipe line and getting out soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick layers complete all as specified and as directed.

Removal of excavated material n.exc 50 mtr away and depositing where directed at a level n.exc 1.5 mtr above from starting point complete all as specified and as directed.

Supplying and laying un-rainforced precast concrete cable cover LV type-I flat size 250 mm x 150 mm x 40 mm in trenches for protection of cable complete all as specified and as directed.

M&L for sand cushioning dry fine for cable cushioning below and above the cable complete all as directed.

Attar Singh and Sons

M/S RISHI RAJ AGRAWAL

3Krishna Enterprises

Asha Construction

MESSARS JAI AMBEY BUILDERS