SPECIAL REPAIRS OF A VEH GARAGES (GARAGE NO. 95A, 95B, 96, 97 AND 98) AND BLDG NO T-127 AT MIL STN NABHA UNDER GE(SOUTH) PATIALA

Amount

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed By Engr-in-Charge.

M & L for 15mm thick ( in two layers of 10mm and 5mm thickness) cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finished complete all as specified and directed By Engr-in-Charge. Note : Water proofing compound shall be measured and paid saparately under item .

M&L 10mm thick cement plastering in cement mortar CM 1:6 finishing the surface even and smooth without using extra cement complete all as specified and directed By Engr-in-Charge.

M&L Preparation of new plastered or unplastered surfaces of walls, two coats of cement base paint all as specified and directed By Engr-in-Charge.

M&L Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over all as specified and directed By Engr-in-Charge.

Supply only integral water proofing compound ISI marked.all as specified and directed By Engr-in-Charge.

Taking down chowkhats or frames (without taking off shutters from the frame) not exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed By Engr-in-Charge.

S&F 30mm thick PVC door factory made solid panell shutters concisting of frame made out of MS tubes for top and bottom rails, MS frames shall be covered with hit moulded plain coulour PVC 'C' chanel having a PVC sheet strip of 20mm width stuck in side with screws. all as specified and directed By Engr-in-Charge.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixed in opening as per specification and drawing all as specified and directed By Engr-in-Charge.

S&F 100 mm size PVC butt hinges all as specified.all as specified and directed By Engr-in-Charge.

S&F 125MM PVC handles all as specified and directed.all as specified and directed By Engr-in-Charge.

S&F 200mm long PVC tower bolt all as specified and directed.all as specified and directed By Engr-in-Charge.

S&F Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beed 20mm size complete all as specified and directed By Engr-in-Charge.

Dismantling of asbestos cement sheets [corrugated, semi-corrugated, etc] in roof coverings complete all as specified and directed By Engr-in-Charge.

S & F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws all as specified and directed By Engr-in-Charge.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws all as specified and directed By Engr-in-Charge.

S&F MS hollow rectangular/square/circular tubes/pipes of Fe410-W(Gde-E-250) Grade as in frame work for roof/rafter/purline/chajja/trusses/columns/struts etc and like similar items etc. complete all as specified and directed By Engr-in-Charge.

S&F for plates /cleats/connplates of Fe410-W(Gde-E-250)quality A etc for frame work all as specified and directed By Engr-in-Charge.

Dismantling of wrought timber truss scantling 40Sq.cm and over in section framed work, provided for complete all as specified and directed By Engr-in-Charge.

Dismantling of wrought timber scantling as in fillets, post rafter , purlins etc under 40Sq.cm in section framed work, provided for complete all as specified and directed By Engr-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed By Engr-in-Charge.

Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises all as specified and directed By Engr-in-Charge.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed By Engr-in-Charge.

M&L for anti skid coloured pressed ceramic floor tiles of minimum size 300X300 mm 8 to 10mm thick in flooring etc set and jointed in neat cement lurry and pointed in white cement to match over and including 20mm thick screed bed in CM (1:4) laid in complete all as specified and directed By Engr-in-Charge.

M&L Coloured glazed ceramic tiles (300 x 600 mm) x 7mm or (300 x400 mm)X7mm thick as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed By Engr-in-Charge.

Taking up or down steel tubing of size15mm bore and removal to store all as specified and directed By Engr-in-Charge.

Taking up or down steel tubing of size 20mm bore and removal to store all as specified and directed By Engr-in-Charge.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing. all as specified and directed By Engr-in-Charge.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing. all as specified and directed By Engr-in-Charge.

Dismanteling 1000ltr water storage tank and removing to store all as specified and directed By Engr-in-Charge.

S&F Rotational moulded polythene water storage tanks, double layered (Cylindrical vertical with closed top) of capacity 1000 lit, hoisted and fixed in position all as specified and directed By Engr-in-Charge.

S & F in repair Bib taps 15 mm dia bore pipe cast copper alloy cromium plated with capstain head screwed down for iron pipe or brass ferrule and fixed all as specified and directed By Engr-in-Charge..

S&F in repair stop cock cast copper alloy chromium plated fancy type ,high pressure with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipe after taking down old stop cock of any description complete all as specified and directed By Engr-in-Charge.

S &F in repair 20mm Stop valves/ gate valve , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and directed By Engr-in-Charge.

S &F 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and directed By Engr-in-Charge.

S/F in repairs low level flushing cistern of PVC 10 ltr capicity incl 45cm long PVC connection with brass nut at both ends, 15 dia stop cock cast copper alloy,screwed both ends , high pressure(wt not less than as specified in SSR), PVC flush pipe 32 mm bore complete all as specified and directed By Engr-in-Charge.

S &F Viterous china ware wash down water closet Orrisa pattern size 580x440mm white with integral foot rests including connection to traps and to flushing pipe, anti syphonage pipe complete fixed in repair.all as specified and directed By Engr-in-Charge.

M&L Hard core of broken bricks of gauge n exc. 63 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface all as specified and directed By Engr-in-Charge.

M&L PCC (1:3:6), 50mm thick as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement all as specified and directed By Engr-in-Charge.

M&L Machine pressed precast concrete inter locking paver block any shape and size made of M-35 grade concrete (with grey cement and no pigment) of 60mm thickness with 6mm top layer of anti abrasive material laid over 25mm thick (compacted) fine sieved sand complete all as specified and directed By Engr-in-Charge.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring.all as specified and directed By Engr-in-Charge.

S&F cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints laid in trenches or in floor of 100 mm bore with sand cast paper all as specified and directed By Engr-in-Charge.

S&F cast iron 100mm sand cast vent cowl with cement joints bore with sand cast paper all as specified and directed By Engr-in-Charge.

S&F 100mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured) all as specified and directed By Engr-in-Charge.

S&F 100mm Branch pieces, double/cross, T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches all as specified and directed By Engr-in-Charge.

S&F CI P & S trap with grating including jointing to waste pipe in neat cement 100 mm dia fixed in cement concrete (1:2:4) type B1.all as specified and directed By Engr-in-Charge.

Demolition of brick work or stone masonry built in cement mortar including all quions, arches, pillers, etc all as specified and directed By Engr-in-Charge.

M&L brick work in CM (1:6) with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius complete all as specified and directed By Engr-in-Charge.

Demolition and breaking up 150mm drain pipes set in cement mortar (salt glazed stoneware/asbestos cement/reinforced) and removal of debris to low lying area to a distance not exceeding 100m, of the following sizes all as specified and directed By Engr-in-Charge.

M & L for150mm bore, cement concrete bed 1:3:6 type C2, using 40mm graded stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid all as specified and directed By Engr-in-Charge.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in deep and getting out in hard / dense soil for foundations, etc or for shafts, wells, cesspits, manholes, pier holes, etc complete all as specified and directed By Engr-in-Charge.

Removing excavated material(soil) to a distance not exc 50mm and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed By Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soils complete all as specified and directed By Engr-in-Charge.

M & L for PCC 1:2:4, type B1, using 20mm size graded stone agregates as in bands, copings, etc., including necessary formwork complete all as specified and directed By Engr-in-Charge.

Demolition of reinforced cement concrete of any description (Reinforecement cut as required to facilitate demolition ) complete all as specified and directed By Engr-in-Charge.

M & L for precast RCC 1:2:4, type B-1 as in man hole cover slabs using 20mm graded stone aggregate and set in CM 1:4 including necessary form work all as specified and directed By Engr-in-Charge. Note : Reinforcement shall be measured and paid separately under item No. 13 below

M&L Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed By Engr-in-Charge.

M & L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cemnt complete all as specified and directed By Engr-in-Charge.

M&L Reinforced concrete pipes, class NP2 laid and jointed complete with collars bore in pipes 150mm all as specified and directed By Engr-in-Charge.

Dismantiling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed By Engr-in-Charge.

S & F for A vehicle garrages Crimp curved sheet pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws as specified all as specified and directed By Engr-in-Charge.

M&L PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregates as in coping , bed plate and the like including weathering slightly rounded or chamferred angle and throating as directed including provision of necessary form work and finish exposed surface even and smoothwithout using extra cement compleate all as specifiede all as specified and directed By Engr-in-Charge.

M&L Preparation old steel surfaces of any desription and applying one coat of synthetic enamel paint all as specified and directed By Engr-in-Charge.

M& L for Preparation new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide as in primer all as specified and directed By Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description all as specified and directed By Engr-in-Charge.

S&F fabrication Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of Fe410-W(Gde-E-250) Grade as in frame work for roof/rafter/purline/chajja/trusses etc and like similar items etc. all as specified and directed By Engr-in-Charge.

M&L for Reinforced cement concrete (Normal Mix),Type B1, 1:2:4 using 20 mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, Footings all as specified and directed By Engr-in-Charge.

M&L for Reinforced cement concrete (Normal Mix),Type B1, 1:2:4 using 20 mm graded stone aggregate Columns, pillars, piers, posts and struts all as specified and directed By Engr-in-Charge.

M&L Use & waste of formwork to sides and soffits of floor, colume , roof beams ,lintels beam ,cantilevers ,shelves including supports ,overhangs and similar work , for rough finished flat surfaces all as specified and directed By Engr-in-Charge.

M&L Mild steel TMT bars 10mm dia & over cut to length, bent to shape required incl cranking bending with0.9 mm dia MS wire (annealed) not less than0.9 mm dia or securing with clips.all as specified and directed By Engr-in-Charge.

Ditto-- but 5mm dia and over upto and incl 10 mm dia in stirrups, spacers and binders.all as specified and directed By Engr-in-Charge.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring with 1.50 sqmm in copper conductor cable ( multistrand) FRLS single core PVC insulated cable in and including PVC concealed conduit ( ISI Marked) of heavy duly with all accessories ie PVC gutties etc terminated in sunken/pressed metal flush box and white modular cover plate with frame for mounting of switches /sockets/ fan regulators etc and continuous earth wire 1.5 Sqmm copper cable PVC insulated FRLS controlled by one switch for one light/fan/sockets point/ all as specified and directed by Engr-in-Charge. in ceiling Portion surface conduit wiring to be done. . Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.iii) Neccessary cutting chasing wherever required and making good the disturbed surface shall be part of job at no extra cost. iv) The wiring is to be done in 'A' Vehicle garage.

All as per item No 2 above, but for one 3/5 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 2 above, but for one 3/5 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 2 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

M&L for Modular switch 1 way 6A, 1 module

M&L for Modular switch 1 way 16A, 1 module type all as specified and directed.

M&L for Modular Socket, 6A - 5 pin, 2 module type all as specified and directed

M&L for Modular Socket 6A/16A - 2/3 pin, 2 module type all as specified and directed.

M&L for taking down existing serviceable Plug & socket 16 Amps capacity and refixing concealed the same all as directed by Engr-in-Charge.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x2.5 sqmm ( line conductor) & 1x2.5 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth . (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size . (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

S&Fin replacement of existing Unsv FTL with new techonlgy ultra bright led tubelight with aluminium heat sink & polycarbonate diffuser having high efficacy of capacity 20 Watt Warm White with BOX TYPE Pre-coated CRCA body, heavy duty regal Batten for LED tube universal batten for G13 t8 lamps including neccesary fitting on wall and making electric connection from ceiling rose to connector with suitable size of electric cable and making good the disturbed surface. Make :- Havells/Bajaj/Philips

S&F in replacement of LED 10 Watt, 2 feet long, Cool day light with NEO Batten10 W 6500K having high efficiency Cat No. LHEXACP7IN1W010. Make -Havells or equivalent makes as mentioned in Appendix 'B' incl necessary electric conection complete all as specified and directed by Engineer-in-Charge. Make :- Havells/Bajaj/Philips

S & F in replacement of suspended type LED light suitable for 'A' veh garage suspended type with PDC Housing, elliptical shaped LED Highbay luminaire with PC Diffuser 70/80 watt Equipped with 4kv inbuilt surge protection, IP-65 Protection rating, 230 volts including cost of GI wire suitable hanging the fitting upto 2 mtr down from truss structure all as specified and directed by engr-in-charge. Make - Bajaj, (Model-Bajaj BLAZE PRO High Bay LED Light BG).

S & F new generation energy saving and environmental friendly long life LED building security light 70 watt IP-65, made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with suitable dia light grade GI pipe bend to shape, including MS clamp of size of required size complete all as specified and directed.

S & F new generation energy saving and environmental friendly long life LED Bldg security light 25 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with suitable dia light grade GI pipe bend to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed.

M & L for Fan step regulator, 120W - 1 module

M&L for ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed by the Engineer-in-Charge.

M&L for replacement of existing earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I

S&Fin replacement of existing Unsv Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type as per IP-54 protection with 200 amp rated bus bar. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job.

S&F in replacement of existing Unsv Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 12 way double door type as per IP-54 protection with 200 amp rated bus bar. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. ii) The disturbed surface shall be match with existing shall be part of job.

S & F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, in the MCB DB Complete with connection testing and commissioning complete all as specifed and directed

S & F 240V, 10 KA 'B' curve miniature circuit breaker (MCB) SPN current carrying capacity 6 to 32 Amp, in the MCB DB Complete with connection testing and commissioning Complete all as specifed and directed

Supply & lay in replacement of existing Unsv XLPE insulated, armoured heavy dutyelectric cable with aluminium conductor, 1100 volt grade of crosssectional area 16 Sqmm 2 Core all as specified & directed by Engr-in-Charge.

Excavating in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for sand cushioning with dry river sand in trenches for cushioning of underground cable line including spreading, leveling, well ramming completed all as specified and directed.

S&F well burnt sub class ‘B’ bricks. ( designated 75) locally available best quality laid dry in trenches for protection of underground cable all as specified and directed.

M&L for replacement of GI tubing light grade 40 mm bore for passing through cables under the floor ,along the wall or along the pole complete all as specified and directed.

M/S RAJ KUMAR GUPTA

NARINDER KUMAR SONS

m/s k.k. construction co.

AGGARWAL & CO