PROVN OF DRAIN FOR RAIN WATER NEAR BLDG No T-23 AND PROVN OF VERANDAH NEAR BLDG NO T-26E OF 133 INF BN (TA) ECO DOGRA AT KUFRI AND PROVN OF CERTAIN MINOR AND REVENUE WORKS AT JUTOGH CANTT UNDER GE JUTOGH

Amount

Excavation in trenches not exc 1.5 m wide and n.exc 1.5m in depth for foundation, footing etc in hard/dense soil complete all as specified and as directed.

Returning , filling in spreading and levelling and well ramming in layers not exc 25cm including watering for filling under floor complete all as specified and as directed.

Removing of excavated material (soils, etc) outside MoD land and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation fillings and mass concrete complete all as specified and directed.

M & L for brick work with old size kiln burnt sub class 'B' bricks, straight or curved on plan exc 6 m in mean radius, built in CM 1:4 complete all as specified and directed.

M&L for broken stone hard core of gauge n. exc. 63mm deposited, spread and levelled in layer n. exc. 15cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40 mm graded crushed stone aggregate) as in sub base under floors, finished even and fair to receive top finish complete all as specified and directed.

M&L for 40mm thick, PCC, 1:2:4, type B-2, using 40mm graded crushed stone aggregate as in sub base, sub floors and pavings, etc. complete all as specified and directed.

M&L for 75mm thick, PCC 1:3:6 type C-2, using 40mm graded crushed stone aggregate as in plinth protection finish the surface even and smooth without using extra cement, complete all as specified and directed

M&L for coloured Non - skid Ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 15mm thick screed bed in CM 1:6, finished even and rough to receive tile complete all as specified and directed.

M&L for 350 x250/450X350 x 6 to 7 mm thick glazed ceramic tiles, coloured, in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over and incl 10 mm thick rendering in CM 1:4, finished even and rough to receive the tiles complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:6 on other than fair faces of brick work or concrete surfaces, finishing surface even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, mixed with and including WPC @ 3% by weight of cement or as per manufacturer's instructions finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying a coat of 2 to 3mm thick wall care putty as per manufacturers instructions and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

S&F mild steel butt hinges 100mm long medium weight colled rolled complete all as specified and directed

S&F aluminium anodized barrel tower bolt 100mm long extruded section complete all as specified and directed.

S&F aluminium handle febricated type anodized 150mm long complete all as specified and directed.

S&F 200 mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F mild steel window/ventilators, fixed type with glazing bars dovetailed or welded complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty / wooden beads etc in squares n.exe 0.50 Sqm in each pane complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description, over 10Cm width or girth including preparation of new steel or steel based surfaces, complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47 mm, made out of 5mm plain colour PVC sheet, reinforced with MS Square tube supplying and fixing in opening as per specification and drawing complete all as specified and directed

S&F factory made solid PVC panel door shutter 30mm thick(style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain clour PVC sheets for top rail ,lock rail and bottom rail either side and as gap inserted for top rail and bottom rail .Panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and nails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

S&F vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe), fixing bolt for pedestal pattern complete all as specfied and directed.

S&F vitreous china half stall urinal white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F plastic water closet seat cover flat bottom with mild steel chromium plated or aluminium anodised hinge device/Pvc hing device complete all as specified and directed.

S&F PVC valve less, syphonic action type low level flushing cistern, white with inlet ball valve , float handle , including brackets 10 ltr capacity including 32 mm PVC flush pipe complete all as specified and directed.

S&F pillar tap 15mm bore cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixed complete all as specified and directed

S&F bib tap, 15mm bore CP, long body, fancy type cast copper alloy, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule, of size complete all as specified and directed.

S&F stop valve 15mm bore CP, fancy type, cast copper alloy, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unioncomplete all as specified and directed.

S & F 15mm dia chromium plated brass central hole wash basin mixer with accessories in wash basins for mixing hot and cold water, screwed down for 15 mm bore GI pipe complete all as specified and directed.

S&F viterous china soap dish approx size 160mm x 160mm x 90mm fixed to plugs with chromium plated brass screws complete all as specified.

S&F PTMT towel rail 60 cm long fixed with and including CP brass screws and wooden/plastic cleats complete all as specified and directed. (Min weight 190gms)

S&F 15mm dia gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F 40mm size (Dia of discharge pipe) waste coupling of PTMT half or full threaded (minimum weight 60 gram) complete all as specified and directed.

S&F 45 cm long (PVC connection) 15 mm bore with PTMT nut complete all as specified and directed.

S & F 15mm bore steel water tubes, `medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20mm bore steel water tubes, `medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F PVC (SWR) floor trap with grating including jointing with solvent cement 75mm bore outlet complete all as specified.

S&F grating doom 100 mm dia of PTMT, minimum weight 25grams complete all as specified and directed

M&L for mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1998 grade St. 240 as in truss, purlin, post etc complete all as specified and directed.

S&F for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends, fixed with approved adhesive complete all as specified and directed.

S&F 75mm bore, PVC (SWR) bends, fixed with approved adhesive complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.

S&F PVC (SWR) 'P' trape, 110mm bore complete all as specified and directed.

M&L for concrete bed to drain pipes of 110mm bore, in PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Excavating in post holes in hard/dense soil (or similar holes) each n. exc 0.50 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed.

M&L for PCC 1:2:4, type B-2, using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M & L for mild steel framed work such as in grills, framed guard bars, hold fasts, framed doors and gates, framed work for water tanks and similar works, doors drilled to fix sheet, prepared to hanging confirming to Fe-290, Gde-E-165 complete all as specified and directed.

S&F Expanded metal, n. exc 4 kg per Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples complete to wood or steel members, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical type with closed top) of 1000 litres capacity, ISI marked, triple layer, marked embosed, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F 20mm bore, nipple PTMT suitable for HDPE water tank Minimum weight 45gms complete all as specified and directed.

S&F 20mm bore, ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. Minimum weight 210 gms, complete all as specified and directed.

S&F 20mm dia gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Demolition of (reinforced) cement concrete in any position and any description not otherwise provided for complete all as specified and directed.

M & L for PCC 1:3:6 type C-2, using 40 mm graded crushed stone aggregate as in surface channels and drains etc including necessary form work and finishing cement concrete surface even and smooth with using extra cement, complete all as specified and directed

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

S&F reinforced concrete pipes of 200mm bore class NP-2 with one collar per length of pipe complete all as specified and directed

M&L for concrete bed to drain pipes of 200mm bore, in PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M & L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation fillings and mass concrete complete all as specified and directed.

M & L for brick work with old size kiln burnt sub class 'B' bricks, straight or curved on plan exc 6 m in mean radius, built in CM 1:6 complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:3 on other than fair faces of brick work or concrete surfaces, finishing surface even and smooth without using extra cement complete all as specified and directed.

M & L for PCC 1:4:8 type D-2, using 40 mm graded crushed stone aggregate as in surface channels and drains etc including necessary form work and finishing cement concrete surface even and smooth with using extra cement, complete all as specified and directed

Extra for forming fair finished surface of channel 30 cm inner girth in cement concrete using extra cement including forms, mouldes, mitred/stopped end etc complete all as specified and directed.

M&L for 75mm thick, PCC 1:3:6 type C-2, using 40mm graded crushed stone aggregate as in sub base etc complete all as specified and directed

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan any radius, built in cement mortar 1:4, in half brick thick wall complete all as specified and directed.

S&F mild steel butt hinges 75mm long medium weight colled rolled complete all as specified and directed

S&F aluminium anodized barrel tower bolt 200mm long extruded section complete all as specified and directed.

S & F anodised aluminium windows and ventilators shuttera, fixed type without sash bar, aluminium section weighting 0.55 kg/m including joining cleats, glazing clips,rubber packing, anodised aluminium snap beading screws etc. complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical type with closed top) of 500 litres capacity, ISI marked, triple layer, marked embosed, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F vitreous china wash hand basin, white, flat back size 550 x 400mm incl 32mm dia CP waste coupling, 750 mm long 32mm bore HDPE waste down pipe, CI brackets complete all as specified and directed.

S&F brass chromium plated tubler towel rail 'D' - type, 60 cm long between flanged complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends, provided with oval access door complete all as specified and directed.

S&F for roof truss (framed) , trussed purlins , rafter, sun shades, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance piece, cleats etc. complete all as specified and directed.

S&F reinforced concrete pipes of 300mm bore class NP-2 with one collar per length of pipe complete all as specified and directed

Surface excavation not exc 30cm deep and averaging 15cm in deep and gating out in hard/dense soil complete all as specified and as directed.

M&L for 100mm thick, PCC 1:4:8, type D-2, using 40mm graded crushed stone aggregate as in sub base etc. complete all as specified and directed.

M&L for 25mm thick, PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in flooring, finish even and smooth without using extra cement complete all as specified and directed.

M&L 18-20 mm thick machine cut kota stone slab, edge cut by machine as in flooring over and including 20mm thick screed bed in CM (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding to exposed edges and polishing complete all as specified and directed.

M&L 18-20 mm thick machine cut kota stone slab, edge cut by machine as in skirting/dado fixed over and including 10mm thick rendering in CM (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding to exposed edges and polishing complete all as specified and directed.

S&F for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed

M/S Shiv Kumar

M/S Jaswant Kumar Aggarwal

NIRMAL SINGH BHOGAL AND SON