ADDN/ALTN AND SPECIAL REPAIRS TO JCOs AND ORs MD ACCN AT KIRKEE

Amount

Dismantling single layer Mangalore pattern or similar tiles in roofing, laid dry, complete all as specified.

Dismantling single layer Mangalore pattern or similar tiles in roofing, laid, bedded or set in lime or cement mortar, complete all as specified.

Dismantling Battens for tiles, shingles etc, of any size including tilting fillets spacing exceeding 15 cm, complete all as specified.

Dismantling wall and ceiling boards (fibre pulp insulation etc.) or insulation boards/slabs/blankets etc. as in false ceiling or partition or covering etc; any thickness including cover fillets, complete all as specified.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position, complete all as specified.

Dismantling timber scantling 40 sq. cm and over in section, framed work, in any position, complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified.

Dismantling floor, hearth or wall tiling of any description including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified.

Dismantling Plain or corrugated steel sheeting of any gauge, thickness, including Nainital or similar pattern roof covering complete , complete all as specified.

Dismantling of boarding, any description and fixed in any position with nails, with or without cover fillets complete , complete all as specified.

Demolition of brick work or stone masonry or PCC block masonry built in cement mortar including all quoins, arches, pillar etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified.

Demolition of brick work or stone masonry or PCC block masonry, laid dry, complete all as specified.

M&L Chipping off loose concrete / plaster upto sound stratum of RCC members such as slab, chajjas, columns, beams and cleaning the surface with wire brushes, washing down with water using water jet including necessary scaffolding and propping to support the structural members where work to be executed inclding removal of debris to a distance exceeding 250 m but not exceeding 500 m complete and providing polymer modified concrete to entire affected area to match with existing profile of the structural concrete member all as specified and directed..

Taking down chowkats or frames (wooden/steel) with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed including making good disturbed wall surfaces/jambs with cement plaster in 1:4 of thickness as required at site, finished even & smooth without using extra cement, complete all as specified..

Taking down chowkat or frames (wooden /steel) with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm each complete all as specified and directed including making good disturbed wall surfaces/jambs with cement plaster in 1:4 of thickness as required at site, finished even & smooth without using extra cement, complete all as specified.

Taking down shutters of any description exceeding 1.0 sq.m and not exceeding 2.0 sq.m each, all as specifed.

Excavation in trenches for foundations etc. or for shafts, walls, cesspits, manholes, pier holes, laying pipes or underground cables etc., not exceeding 1.5 m in width and not exceeding 1.5 m in depth and not exceeding 10 sqm on plan, lift upto 1.5 m, in soft and loose soil including getting out the excavated material, complete all as specified.

Excavation in trenches for foundations etc. or for shafts, walls, cesspits, manholes, pier holes, laying pipes or underground cables etc., not exceeding 1.5 m in width and not exceeding 1.5 m in depth and not exceeding 10 sqm on plan, lift upto 1.5 m, in hard and dense soil including getting out the excavated material, complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm in any kind of soils, complete all as specified.

Removing excavated materials (soils) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified.

M&L Post construction anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete, all as specifed..

M&L Moorum filling in floors in layers including watering , ramming and cosolidation for average thickness 125 mm complete, all as specifed.

M&L Hardcore of broken stone or boulder n. exc. 63mm gauge, deposited, spread, levelled and well rammed including watering to a true surface, complete, all as specifed.

M&L Providing plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregates), as in filling in for levelling course on roof slab surfaces, to ensure all depressions and undulations are filled and a plain surface with required camber is achieved, complete all as specified.

M&L Providing plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates), as in floor 25 mm thick , complete all as specified.

M&L Providing plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates), as in floor 75 mm thick complete , complete all as specified.

M&L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection, 75mm thick, laid in alternate bays including finishing the surfaces even and smooth using extra cement; , complete all as specified.

M&L Providing plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregates), as in lean concrete in sunken floor, complete , complete all as specified.

M&L Providing plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates), as in coping, bed plates, fixing of hold fasts and other similar works and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of necessary formwork, complete all as specified.

M&L Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in roof kerbs or mud stops, round or chamfered on edge, complete all as specified.

M&L Reinforced cement concrete (Nominal mix) 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

M&L Providing plain cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregates), as in coping, bed plates, fixing of hold fasts and other similar works and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of necessary formwork complete , complete all as specified.

M&L Plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregates), as in foundation, filling or mass concrete, complete all as specified.

M&L Providing plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregates) as in surface channel and drains, complete all as specified.

M&L Precast cement concrete 1:3:6 type C-0 (using 12.5 mm graded stone aggregates) louvres and jallies, 25mm thick (measured solid), including all mouldings, set in cement mortar 1:4, complete all as specified.

M&L Walling of random rubble, uncoarsed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified & directed.

M&L Brickwork using old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified & directed.

M&L Brickwork using old size fly ash bricks, straight or curved on plan to any radius in half brick thick wall, built in CM (1:4) complete all as specified & directed.

S&F 2nd class soft wood Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps, complete , complete all as specified.

S&F 2nd class hard wood Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps, complete , complete all as specified.

M&L Second class hardwood, wrought, in scantling, timber framed and fixed all as specified and directed.

S&F Plain, solid, straight chowkats and frames of 2nd class hard wood, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete , complete all as specified.

S&F Flush shutters, 30 mm thick, solid core construction, with block board core and plywood face panels commercial type on both faces including 6mm thick Ist class HW (Teakwood) beading all around on edges, complete all as specified.

S&F 2nd class hard wood 35mm thick factory made, panelled shutter (any number of panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneer particle board with commercial veneering on both faces. The size of the rail and styles as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated, supplied and fitted to chowkhat; complete all as specified..

S & F 2nd class hard wood 35mm thick factory made, glazed and skeleton shutter open rebated and prepared to receive glass,gauge,etc. (without sash bars), edges of framing plain,chamfered or rounded fitted with cut and mitred beads for securing glass,etc; The size of the rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated, supplied and fitted to chokhats, complete all as specified.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplied and fixing in opening all as per specification & drawing, complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed colour PVC 'C’ channel having a wood grain printed PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and as directed.

M&L Post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete.

S&F Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Powder coated aluminium sliding window shutter and ventilators, aluminium sactions weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, locks, screws etc complete all as specified and directed.

S&F Mild steel Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete , complete all as specified.

M&L Running welding in repairs in any length to old doors / shutters of thickness exceeding 9 mm but not exceeding 20 mm for fixing hinges, tower bolt, sliding door bolt, handles, locking system etc. complete , complete all as specified.

Refixing shutters of any description in the same opening exceeding 1 sq.m and not exceeding 2 sq.m each complete, after necessary easening, complete all as specified.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100 mm size type B-22, all as specifed.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 125 mm size type B-22, all as specifed.

S&F Extruded aluminium alloy handles, 125 mm long, fabricated type, anodised, complete all as specified.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed of size 150 mm, complete all as specified.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed of size 200 mm, complete all as specified.

S&F 300mm, Mild steel ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

S&F Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 300 mm, complete.

S&F Rolled MS sections conforming to IS-2062:2006 (Fe-290) as in bands, straps, supports, hooks, heavy, for large gates, clamps, hold fast, hooks for hanging fans, etc. including embedded portion duly painted with bituminous paint and sanded, complete all as specified.

S&F Double legged floor door stopper of aluminium alloy with rubber tip bottom, overall length of cover plate 150 mm, complete.

S&F Stainless steel plate racks of size 31" x 24" x 10" (or nearest size), made out of 0.63 mm thick stainless steel sheet, SS screw and round pipe, conforming to cat part No. SSKPR-318 of Silver Shine or of equivalent model in other makes specified in Appendix 'C' complete.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete.

S&F Mild steel Hat pegs, solid body, 125mm to 175 mm and fixed complete.

S&F in repairs Sink made out of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes, with waste coupling and waste pipe of 32mm including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe for over all size 495mm x 420mm, bowl size 410mm x 330mm x 160mm conforming to cat part No. SSSB-06A of Silvershine or of equivalent model in other makes specified in Appendix 'C' complete all as directed.

S&F Sheet glass 4.8 mm thick, ordinary quality and glazing fixed through glazing clips in square not exceeding 0.5 sq. m in each pane complete.

S&F Sheet glass 4.8 mm thick, ordinary quality, sheet glass is ground or obscured or frosted, on one side and glazing fixed through glazing clips in square not exceeding 0.5 sq. m in each pane complete.

S&F in repair 18/19 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination on other side balancing white lamination, fixed with screws to timber frame work including 1st Class HW (TW) 6 mm thick beading / liping all around on edging of prelaminated board, complete , complete all as specified.

S&F Hasp and staple safety type mild steel, wire type stove enamelled black including bolt to hinge plate and fixed with screws of 150 mm size complete.

S&F continuous (Piano) hinges, mild steel bright finished or electro galvanised width of flap 30mm complete.

S&F in repairs, magnetic catch, in wooden frame including neccesary fixures complete.

S&F stainless steel wire cloth, 0.36 mm nominal size and average width of aperture 1.40 mm fixed with stainless steel wire staples etc complete all as specified and directed.

M&L Rolled structural mild steel, fabricated and erected in position, Fe 410 -W (Gde E- 250) quality A, in Roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified.

M&L Rolled structural mild steel, fabricated and erected in position, Fe 410 -W (Gde E- 250) quality A, in in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc., complete all as specified.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape reqd, including cranking, bending spirally for hooping for columns and binding with mild steel annealed wire of dia not less than 0.9 mm or securing with clips complete. .

Supply and fixing Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick (TCT) of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified and directed.

Supply and fixing Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick (TCT) of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified and directed.

M&L SG Gypoc T-Grid false ceiling system with 12 mm thick panel laminated with PVC film on face side and metalised polyster film on the back with all four edges sealed with PVC film ceiling tiles including all necessary ancillaries and fixing arrangement as per manufacturer's instructions in the grid size 600 x 600 mm which shall consist of main tee on wall of size 38 mm x 24 mm x 0.3 mm, cross tee of size 25 mm x 24 mm x 0.3 mm, wall angle of size 20 mm x 14 mm x 0.4 mm using purpose made members interlocking to each other and level with level clip and making holes etc. all as specifed and directed. (Make : Gyproc (Gyprex) or equivalant as approved by GE).

S&F 19/20 mm dia MS pipe powder coated of approved colour as in decorative type curtain rods for fixing curtain rod complete.

S&F Mild steel powder coated bracket suitable for 19/20mm dia curtain rod (minimum projection from wall 75 mm) fixed in wall including drilling, rawl plug, screws etc complete , complete all as specified.

S&F in repairs, 750 liters capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) in white coloured three layered ISI Marked, hoisted and fixed in position all as per specified and directed including 20 mm size ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete.

S&F 20mm dia ‘D’ type brass CP tubular towel rail 60 cm long between flanges complete.

S&F Brass chromium plated shower rose with or without swivel joints, any size including fixing to a steel pipe or union of size 125mm size complete.

M&L Rendering 15 mm thick in cement mortar 1:6 on on stone masonry surfaces or other than fair faces of brick work or concrete surfaces including dubbing out average 10 mm thick on irregular face of wall in cement mortar 1:6 and finishing the surface even & smooth without using extra cement, complete , complete all as specified.

M&L Rendering 15 mm thick in cement mortar 1:6 on on stone masonry surfaces or other than fair faces of brick work or concrete surfaces including dubbing out average 10 mm thick on irregular face of wall in cement mortar 1:4 and finishing the surface even & smooth without using extra cement, complete , complete all as specified.

M&L Rendering 5mm thick in cement mortar in 1:3 on ceiling over a coat of 1.5 mm thick white putty, finished even and smooth fair, all as specified.

M&L Rendering 15 mm thick in cement mortar 1:3 on on roof surfaces mixed with water proofing compound @ 3% by weight of cement finished even and smooth with using extra cement for laying membrane. (WPC shall be measured and paid at supply only rates seperately).

M&L Water proofing treatment to RCC roof slab and shall be carried out as specified below and as directed

(a) The roof surface shall be thoroughly wire brushed, cleaned to eliminate all sharp projection , surface washed, dried up and cleaned of all foreign matter and dust to receive primer.

(b) M&L Applying bituminous primer on cleaned surface @ 0.40 Litre/Sqm.

(c) M&L Providing APP polymer modified approved membrane 3mm thick, non woven, polyster,weighing not less than 3.6 Kg/Sqm and laying on roof surface and parapets with laps, overlaps and sealing joints as specified and applied completely by torch application method, the overlap of membrane while torching shall be kept 100mm on length wise and 100 mm width wise; all as specified & directed.

(d) M&L Carrying out test by flooding water for 24 hrs for leakages & seepages and rectifying the same to the entire satisfaction of GE.

(e) M&L Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 litre/Sqm on the top of membrane surfaces complete all as specified & directed.

(f) The treatment shall be carried out as per manufacturers instructions and through authorised applicator of manufacturer.

(h) Notes:- The contractor shall furnish the following before and during progress of water proofing work:- (i) Quality confirmation from the manufacturer of the product alongwith quantity supplied. (ii) Manufacturer test certificate. (iii) The result, if tested in any of the independent laboratory or testing if ordered by GE, the testing charges shall however shall be borne by the contractor.

Supply only water proofing compound ISI marked.

M&L Rendering 15 mm thick in cement mortar 1:3 on on stone masonry surfaces or other than fair faces of brick work of toilets and finishing the surface even & smooth without using extra cement, complete , complete all as specified.

M&L Rendering 15 mm thick in cement mortar 1:4 on fiar faces of brick masonry or concrete surfaces and finishing the surface even & smooth without using extra cement, complete , complete all as specified.

M&L Raised Struck pointing to block in course or ashlar masonry or concrete block walling in cement mortar 1:4, complete.

M&L Rendering 10 mm thick in cement mortar 1:6 on fiar faces of brick masonry or concrete surfaces and finishing the surface even & smooth without using extra cement, complete.

M&L Disconnecting existing tanks, setting aside (or lowering if required) overhead PVC/HDPE water tanks of capacity exc 500 and not exceeding 1000 litres for and including repairs, cleaning etc. and hoisting if required, reconnecting and re-fixing in position complete , complete all as specified.

M&L Bitumen blown any grade applied hot in two coats to concrete surfaces at the rate of 1.5 kg per sq. m, in floor complete , complete all as specified.

M&L Polythene film black 50 micron, laid in floor, complete , complete all as specified.

M&L full body Vitrified coloured Ceramic tiles of light colour shade, 10 mm thick (square/rectangular), polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over screed bed or bedding layer of cement mortar, complete all as specified and as directed.

Ditto all as per item No. 100.00 above but for work on vertical surfaces such as skirting, dados and riser to steps including 10mm rendering in CM (1:4) complete all as specified and as directed.

M&L 20 mm thick screed bed or bedding layer of cement mortar 1:6, for laying floor finishes, complete all as specified and as directed.

M&L Non-skid coloured, ceramic tiles, 7 mm to 8 mm thick (Square or rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile, laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450x300x7mm thick of approved colour as in skirting/dado or verticle surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete, fixed over & including 10mm thick backing coat in cement mrotar 1:4 including triangular filleting in cement mortar 1:4 on top of skirting/dado all as specified and as directed.

M&L Prepolished machine cut Kota stone slab 20 to 25 mm thick, laid in flooring over and including screed bed 15 mm thick in cement mortar 1:4, jointed with grey cement slurry and pointed with coloured cement to match the shade of Kota stone as in floor including rubbing and polishing complete all as specified and as directed.

M&L Prepolished machine cut Kota stone 20 to 22 mm thick, laid, jointed with grey cement slurry and pointed with coloured cement to match the shade of Kota stone as in treads, risers, landing etc laid over and including 10 mm thick cement mortar 1:4, including rounding of treads and polishing complete all as specified and as directed.

M&L Prepolished machine cut Cuddappa stone slab 20 to 25 mm thick, laid in flooring / platform (in one piece) / walls etc. over and including screed bed 15 mm thick in cement mortar 1:4, jointed with grey cement slurry and pointed with coloured cement to match the shade of Kota stone as in floor including rubbing and polishing complete all as specified and as directed.

M&L Rounding the edges of stone slab of any type, in steps, cooking platform and other similar situation including griding and polishing all as specified and as directed.

M&L 16 to 18 mm thick granite (of any type, table rubbed & mirror polished ) in cooking /kitchen platform in single piece, laid over cuddappa stone platform over and including 15 mm thick screed of cement morter (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade with granite, complete all as specified and as directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, glossy finish, laid in required colour & pattern over and including 30 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc. complete.

S&F PVC (SWR) pipes of size 110mm bore, single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete.

S&F PVC (SWR) pipes of size 75mm bore, single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete.

S&F PVC (SWR) bends any radius 110 mm bore complete.

S&F PVC (SWR) bends any radius 75 mm bore complete.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore complete.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete.

S&F PVC (SWR) vent cowl 110 mm complete.

S&F PVC (SWR) vent cowl 75 mm complete.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for bore of pipe 75 mm complete.

S&F PVC SWR branch piece, single (single 'Y') equal or unequal of 75 mm bore complete.

S&F PVC SWR branch piece, single (single 'Y') equal or unequal of 110 mm bore complete.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for bore of pipe 110 mm complete.

S&F CP Soap dish as per sample available in GE office, fixed to plug with CP brass screws complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement suitable for 75 mm dia outlet complete.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement suitable for 110 mm dia outlet complete.

Taking up or down 15 mm bore steel water tubeing including connections for cleaning and re-fixing or replacement either at the same locations or other locations, complete , complete all as specified.

Taking up or down 20 mm bore steel water tubeing including connections for cleaning and re-fixing or replacement either at the same locations or other locations, complete , complete all as specified.

M&L Steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to or laid concealed in walls / ceiling and floors or laid in trenches complete all as specified for following sizes:-

15 mm nominal bore

20 mm nominal bore

50 mm nominal bore

Re-fixing only old serviceable GI tubing with and including new fittings and fixed complete to walls and ceiling or laid in floors or in trenches complete all as specified and as directed of following sizes:-

15 mm nominal bore

20 mm nominal bore

S&F 20 mm size ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete , complete all as specified.

S&F in repairs, Vitreous china Wash Hand Basin white flat back of size 630 mm x 450 mm or nearest size in makes as listed in Appendix 'C,' including PTMT waste coupling 32mm, chain and plug and PVC waste pipe including CI brackets, etc. complete but excluding taps , complete all as specified.

S&F in repairs vitreous China squatting pan of Orissa pattern cat part No. CALINA S3010102 of CERA or of equivalent model in makes as specified in Appx 'C' with P or S trap of size 580 mm X 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe and lime concrete bedding and connection to antisyphonage pipe etc including making good to floor, complete all as specified.

S&F in repairs PVC low level flushing cistern twin flush (dual flow) of 10 ltrs capacity conforming to cat part No. B1020106 of CERA or of equivalent model in makes as specified in Appx 'C' inclusive of brackets and PVC bend long type and connecting to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make, complete all as specified.

S&F Pillar taps, chromium plated cast copper alloy with capstan heads, fancy type, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore.

S&F PVC connections 15mm size with PTMT nuts, of length 450 mm long complete, all as specified.

S&F Bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed down, high pressure, screwed for iron pipe or for brass ferrule and fixed, suitable for size 15 mm dia bore.

S&F Stop valve, cast copper alloy, chromiun plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union and fixed, suitable for size 15 mm dia bore.

S&F Angle cock, cast copper alloy, chromiun plated, two way with wall flange and capstan head, all as specified.

S&F Health focet (jet spray), cast copper alloy, chromiun plated, with PVC flexible connection and wall hook, all as specified.

M&L Preparing surfaces of wood or wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of creosote oil complete.

M&L Preparing surfaces of wood or wood based materials and treating ends of posts, back of chowkhats etc. with tar or coal tar black paint, area exceeding 0.1 sq.m but not exceeding 0.5 sq.m each complete , complete all as specified.

M&L Sanding newly tarred or painted surfaces with clean sharp sand complete all as specified.

M&L Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete.

M&L Preparation of old wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete.

M&L for preparation of new surfaces of steel and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified.

M&L Preparing newly plastered surfaces and applying three coats of white wash on ceiling, complete all as specified.

M&L Preparing newly plastered surfaces or unplastered surfaces of walls and applying 1.5mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified.

M&L Preparing newly plastered or unplastered surfaces of walls and applying two coats of cement based paint complete , complete all as specified.

M&L for complete removal of existing treatment on external wall surface and applying two coats of cement based paint overa coat of exterior grade prime complete all as specified.

M&L Complete removal of existing treatment of walls and applying 1.5 mm thick Birla wall care putty in two coats and applying two coats of oil bound distemper over a coat of primer complete , complete all as specified.

M&L Complete removal of existing treatment of walls and applying two coats of white wash complete , complete all as specified.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern) ivory coloured with integrated 'P' or 'S' trap outlet including connection to flush pipe and outgoing pipe and plastic water closet seat cover any colour closed pattern with flat bottom and PTMT hingind device complete all as specified and directed.

M&L Writing letters or figures (Block, Roman, Italic or Indian) n. exc. 30 cm high using thick synthetic enamel paint of approved tint, complete.

M&L Point wiring complete with and including two single core FRLSH PVC insulated unsheathed flexible bright annealed multi stranded copper conductor cables 1.5 Sqmm (22/0.30 mm) 1100 volts grade and one 1.5 Sqmm (22/0.30 mm) 1100 V grade FRLSH PVC insulated, unsheathed flexible multi stranded copper conductor cable as continuous earthwire connected to metallic bodies of luminaires/fans etc; at one end and to common earth dolly at other end, drawn through and including heavy grade PVC casing and caping on walls/ceiling including all accessories/fittings/ etc; ISI marked with and including factory made PVC board sunk surface type of required size with 3 mm thick hylam/ PVC sheet screwed with 4 No's cadmium plated screws and cup washers for mounting switches, socket outlets and fan regulator etc. and PVC square box for mounting ceiling rose / holders etc. including taking down old unserviceable existing point wiring of any type all as specified for the following:-

(a) One light point controlled by one, one way switch

(b) One fan point controlled by one, one way switch and one regulator

(c) One Exhaust fan point controlled by one, one way switch

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board complete all as specified

(e) One 3 pin 5 amps socket outlet point on same board complete all as specified.

(f) One light point controlled by two- 2 way switches

(g) One bell/buzzer point controlled by one bell push complete all as specified.

Ditto- all as per item here-in-before but with 2.5 Sqmm cables for one 15A, 6-Pin socket outlet point on independent board with & including 2.5 Sqmm FRLSH cable as earth wire complete all as specified.

M&L Sub main wiring complete with two single core 6 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLSH cable with continuous copper earth conductor of 6 sqmm in and including PVC casing capping of required size including accessories, fixed on walls / floors / ceiling etc. complete including taking down old unserviceable existing sub main wiring of any type all as specified . (Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 6 Sqmm conductor and one run of PVC casing capping shall be measured as one unit length.)

S&F switch piano flush type, 6 amps, 230 volts, single pole one way .

S&F switch piano flush type, 16 amps, 230 volts, single pole one way .

S&F bell push, flush type, 5amp.

S&F lamp holder PVC insulated body with back plate suitable for batten/angle fitting.

S&F switch piano flush type, 06 amps, 230 volts, single pole two way .

S&F socket outlet, 2 in 1, 3 pin, 6 amp flush type.

S&F socket outlet, 2 in 1, 3 pin, 6 and 16 amp flush type.

S&F ceiling rose PVC/polycarbonate surface bakelite, 2 to 3 terminals with base plate.

S&F Bell, AC, 230 volts, singe pole.

S&F BLDC ceiling fans complete with all accessories 230 volts 1200 mm sweep BEE 5 star rated including taking down old ceiling fans and deposit in MES store yard conformig to cat No. EFFICIENCIA NEO of Havells OR PLASMA28W with regulator of Halonix or equivalant in other approved makes specified in Appendix 'C'.

S&F Exhaust fan, 300 mm sweep, steel body with blade, frame and louvers, shutter etc, single phase suitable for 230 volts 50 HZ and connecting up complete including provision of 3 core flexible cord from ceiling rose to connector of fan with cable of suitable size and fixing the fan with suitable size nut, bolt, washers etc. complete. Note: Necessary fixing arrangement i.e. making hole in the wall, making good disturbed surfaces shall be deemed to be included in the quoted rate.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified. Makes : Cat part No. LUMILINEPLUSBS20WLED865SPCSS of Havells or of equivalent model in other makes specified in Appx 'C'.

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified. Makes : Cat part No. LUMILINEPLUSBS10WLED865SPCSS of Havells or of equivalent model in other makes specified in Appx 'C'.

S & F LED lamp 12 Watt, CDL, B-22 (pin type), 230V, PF-0.95(min) all as specified.

Supply and fixing LED lights fitting 1x 10W, bulk head liminairs including LED light, driver, holder, connecting up with three core flexible copper conductor of suitable size complete all as specified. Makes : Cat part No. HEXAFT 10W LED 857 SSYMBOPC of Havells of equivalent model in other makes specified in Appx 'C'.

S&F Sheet metal enclouser for DB SPN 8 way with 200 Amp Rated Bus bar 240 V, double door suitable for housing MCB,s and isolator complete .

S&F MCB Single pole and neutral with current carrying capacity 40 amps, in the MCB DB 240 V breaking capacity 10 KA ,B- curve, complete as specified.

S&F MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,B- curve complete all as specified.

S&F LED street light fitting complete with all fitting & fixing accessories, 35 Watt 230 volts AC, outdoor type, made out of high pressure die cast aluminium housing and heat resistant glass and high efficient electronic driver, lamp bracket with impact and corrosion management in multiple optic, IP 65/66 thermal protection, prewired, connected with and including 3 core flexible copper conductor cable PVC insulated of 1.5 sqmm cross sectional area of required length to connector of fitting, on walls PCC/Steel poles etc. including 32 mm dia GI pile light grade bracket 1.0 m length made to shape required including clamps and botls etc. fixed on walls etc. complete as specified.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service onnections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire, one twin core cable flat or circular of size 6 sq. mm all as specified.

(i) Incomer

(a) MCCB FP, 16 KA rapturing capacity 100 Amps, Ics=100% of Icu, thermal magnetic setting including connection with bus bar - 1 No

(ii) Out going

(a) MCB SPN 32 Amp 10 KA 'B' curve - 04 Nos

(b) MCB SPN 10 Amp 10 KA 'B' curve - 01 No

(e) LED type RYB phase indicator lamp with back up HRC fuse - 01 set

(f) Suitable space for fixing 4 Nos single phase smart energy meter.

(i) Incomer

(a) MCCB FP, 16 KA rapturing capacity 100 Amps, Ics=100% of Icu, thermal magnetic setting including connection with bus bar - 1 No

(ii) Out going

(a) MCB SPN 40 Amp 10 KA 'B' curve - 06 Nos

(b) MCB SPN 10 Amp 10 KA 'B' curve - 01 No

(e) LED type RYB phase indicator lamp with back up HRC fuse - 01 set

(f) Suitable space for fixing 6 Nos single phase smart energy meter.

(i) Incomer

(a) MCCB FP, 16 KA rapturing capacity 63 Amps, Ics=100% of Icu, thermal magnetic setting including connection with bus bar - 1 No

(ii) Out going

(a) MCB SPN 40 Amp 10 KA 'B' curve - 03 Nos

(b) MCB SPN 10 Amp 10 KA 'B' curve - 01 No

(e) LED type RYB phase indicator lamp with back up HRC fuse - 01 set

(f) Suitable space for fixing 4 Nos single phase smart energy meter.

S & F smart single phase two wire pre paid smart energy meter conforming to IS 16444:2015 (reaffirmed 2020) marked in existing panel board with pre payment capacity touch key pad based digital having current range 10 to 60 amps 240 Volts,accuracy class 1.0 alongwith parallel home disply slit unit with inbuilt load control switch containing provision for TOD & RTC, capable to define for tarrif slabs, happy hours and holiday definition including modem complete to charge remotely, send sms/message for balance amount, charge amount etc including taking down old electric meter and deposited to E/M store yard all as specified and directed. Note: (i) Pre-paid energy meter is to be compatible with existing station software system and accordingly before placing order contractor shall check software system. (ii) Meter shall have facility to work in normal mode in absence of software system.

Supply, installing, connecting, testing and commissioning of electric water Heater storage type capacity 25 Liters 5 star rated with precaliberated thermostat, safety valve, preset thermal cut out, fire retardant power cord, ABS outer body, colour changing indicator, copper heating element with rated voltage 2 KW, 230 volt, 50 Hz of temperature range 35 to 75 degree Celsius, horizontal or vertical type with ISI certification mark, installing on wall with suitable size bolts, nuts, etc and connecting up with water and electric connections including hot and cold connection pipes complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode 60cm x 60cm x 6.3mm thick buried directly in ground (earth pit not less than 2.25 mtr in deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level including connecting GI earth wire 4mm dia by GI nut, bolt, washers all as shown in electrical plate No. 3 of SSR Part I of 2009 including funnel for watering, PCC 1:3:6 type C-2 using 40mm graded stone aggregates as in pit / chamber, RCC 1:2:4 type B0 using 12.5mm graded stone aggregates and 6mm dia mild steel bars at 100mm c/c as in chamber cover, charcoal, salt etc complete including excavation and earth work in any strata, test point and testing on completion including filling up the earth pit with black cotton soil for best result and removal of excavated material from site all as specified and directed. (Note : GI earthwire and GI protection pipe upto 7.5 mtr length shall be included in this item.)

M&L Construction of Fly ash bricks masonry valve pit chamber of size 1.20m x 1.20m x 1.0 m (depth) internal dimensions with 15 cm thick foundation using PCC 1:4:8 type D-2 over 15cm thick hard core, 23 cm thick fly ash brick wall built in cement and sand mortor 1:4, 15mm thick internal plaster including 50 mm thick PCC 1:3:6 bedding, 3mm thick MS sheet cover with 40mm x 40mm x6mm MS angle iron frame fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) coping with 25mm x 6mm flat iron hold fast with handle and locking arrengement including necessary painting steel surfaces with two coats of synthetic enamel paine over a coat of red oxide primer, excavation, earth work, returning & filling in type of soil and disposal of surplus soil at a distance of not exc. 50 m, complete all as specified.

Supply, laying, jointing & testing 250 mm dia DI-K7 class pipes with spigot and socket, suitable for Push on rubber joint, with internal cement mortor lining, and external zinc and black bitumen coated pipes in any lengths conforming to IS:8329-2000 including Rubber Gasket & joints as per IS:9523-2000 laid in trenches/ Road/ Ducts/ Footpath/ on wall/ on floor locations, including taking down/out existing pipes of any type, size, complete all as specified.

S&F Cast Iron/Ductile iron specials and fitting upto 300 mm bore pipes such as Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc. complete all as specified.

S&F in repairs 50 mm gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs 20 mm gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply, laying, fixing, testing and commissioning of cast iron sluice valve flanged type, class PN 1.6 of size 250 mm dia, conforming to IS-14846 with all necessary allied works, in repairs complete all as specified.

Supply, laying, fixing, testing and commissioning of cast iron air release valve with two single air out let conforming to IS-14845 of size 80 mm bore, PN 1.0, complete with all necessary allied works, in repairs complete all as specified.

M&L dry river sand cushioning for cable protection in trenches complete as per the process specified in SSR Part-I 2009, all as specified and directed. Note: Punned thickness of the sand shall be measured and paid.

Supplying and laying un-reinforced precast concrete cable cover factory made, ISI marked of class LV type 1, flat of size 250 mm x 150 mm x 40 mm, complete all as specified and directed.

Supplying, Laying, Testing & Commissioning of UG LT cable, 25 Sqmm, 4 core, 1100 volts grade, XLPE insulated, galvanised, steel strip or wire armoured with multi stranded aluminium conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/ MDB in building etc to suit the cable including material & labour for all jointing/ connecting material as required size, cable laid in trenches/ ducts/ under plinth floors, passing through pipes, fixed on wall etc complete all as specified and as directed by Engr-in-Charge, for the following sizes: -

(a) 25 Sqmm, 4 Core

(b) 35 Sqmm, 3.5 Core

S&F in repairs GI tubing light grade for protection of cable with all necessary fittings accessories such as MS 40x3mm clamps of suitable length , nuts, bolts and washers and fixed complete to wall/ceiling or laid under floors complete all as specified and directed of the following sizes:-

(a) 40 mm dia bore

(a) 50 mm dia bore

M&L for road cutting for laying GI pipe for protection of cable upto depth of 45 cm and making good the disturbed surface to match the existing complete all as specified and directed.

SHREE KRISHNA INFRASTRUCTURE

Horizon Construction

M/s L. K. Agarwal

N. H. Saluji & Associates

United Sales Corporation

Shree Ayyappa Engineering

M/s S. R. Constructions