8599/GWL/E8 PROVN OF GUARD ROOM, CHAIN LINK FENCING, OFFICE CUBICLES AT MORAR CANTT AND CERTAIN SANCTIONED WORKS OF NCC OTA GWALIOR UNDER GE GWALIOR

Amount

M&L for surface dressing n exc 15 cm deep complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m but n. exc 3.00 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified.

M&L for reinforced cement concrete nominal mix type A-1 (1:1.5:3) ( using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams , plinth beams, base for coloumns and mass concrete etc. complete all as specified and directed.

M&L for reinforced cement concrete nominal mix type A-1 (1:1.5:3) ( using 20 mm graded stone aggregate ) as in coloumns , pillars , piers , posts and struts etc. complete all as specified and directed.

M&L for reinforced cement concrete nominal mix type A-1 (1:1.5:3) ( using 20 mm graded stone aggregate ) as in beams , cantilevers bressummers , lintel over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete nominal mix type A-1 (1:1.5:3) ( using 20 mm graded stone aggregate ) as in slab supported on walls ,beams, coumnns in floor , roof , landing complete all as specified and directed.

M&L for reinforced cement concrete nominal mix type A-1 (1:1.5:3) ( using 20 mm graded stone aggregate ) as in chajjas . complete all as specified and directed.

M&L for use and waste formwork to sides of concrete foundation ,footing, base of coulmn , raft, raft beam sides and soffits of foundation and plinth beam for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork to soffits of suspended slabs such as roof slabs , floor slabs , landings and similar works , not exceeding 200 mm thick ( horizontal or sloping ) including slab edges for rough finished surfaces of concrete complete all as specified and directed

M&L use and waste formwork for to sides of pillar ,post ,struts ,pier column rough finished surfaces of concrete rough finished surfaces of concrete complete all as specified and directed

M&L for use and waste Formwork to sides & soffits of floor or roof beam rough finished surfaces of concrete complete all as specified and directed.

M&L for Use and waste Formwork to chajjas including edges for rough finished surfaces of concrete complete all as specified and directed

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars ,6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia , as in stirrups , spacers , and binders , cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L forTreating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for Moorum red bajri filling in floor or paving laid in layers n. exc. 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate as levelling course/mass concrete complete all as spd and directed.

M & L PCC (1:2:4) Type B1 using 20 mm graded stone aggregate as levelling course/mass concrete complete all as spd and directed.

M&L non skid ceramic Coloured tiles, 300mmx300mmx7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles, coloured tiles, 200mm x 300mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:6) complete all as specified and directed.

M&L for machine cut Kota stone slab 20 mm to 25 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing , over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6 ) complete all as specified and directed.

M&L for machine cut kota stone slab 20mm -25 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for rubble random rubble uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed.

M& L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement including (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked.

M&L for applying two coat of oil bound distemper over new plastered surface on walls including preparation of new surface and one coat of alkalli resistance primer

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 2 coat of cement base paint over a coat of primer complete all as specified and directed.

Supplying and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, wooden beads etc complete all as specified and directed

S&F pressed steel frame 125mmx60mm for doors with one or more rebates including necessary fixing lungs and hinges, lock strike plate,etc complete all as specified and directed

M & L for factory made 35 mm 2nd class Hard Wood, plain framed factory made panelled shutters ( two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed.

S&F aluminium alloy, anodized sliding door bolt of 250mm length with hasp and staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S & F butt Hinges, medium weight, stainless steel,100 mm size complete all as specified.

S & F butt Hinges, medium weight, mild steel,100 mm size complete all as specified.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F for aluminium anodised barrel tower bolt of 150mm of extruded section complete all as specified.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rai ; Panelling of plain colour PVC sheet 5 mm thickness to be fitted in MS frame welded/sealed to the style and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

S & F factory made steel windows with side hung glazed window including projecting type hinges with steel handles and steel peg stays , complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F factory made steel windows with side hung glazed window including projecting type hinges with steel handles and steel peg stays , complete without glazing bars, dovetailed or welded complete all as specified and directed.

M & L for 35 mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

S & F factory made steel vetilator with top hung glazed shutters, including projecting type hinges, with steel handles and steel peg stays , complete with glazing bars, Complete all as specified and directed

S&F factory made steel ventilator with top hung glazed ventilator including projecting type hinges with steel handle and steel peg stay complete witout glazing bar , dovetailed or welded complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality in square n exc 0.5 sqm each pane in new glazed shutter, complete all as specified and directed.

S&F 3mm thick pin headed figured sheet glass quality in square n exc 0.5 sqm each pane in new glazed shutter, complete all as specified and directed.

S&F 25mm dia stainless steel curtain rod not less than 0.80mm thick including fixing of sufficient brackets ( minium 2 nos at every 1.50m length) complete all as specified and directed

S&F End Knob 25mm dia stainless steel for curtain rod complete all as secified and directed

S&F tubular towel rail of brass chromium plated , 20 mm dia, D type, 60 cm long betweem flanges complete all as specified and directed.

S & F vitreous china wash basin,white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, scrwed down high pressure with or without lettereed hot or cold with long shanks, screwed for iron pipe complete all as specified and directed as in repair.

M&L for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed in repairs and making good to floor, complete all as specified and directed.

S&F Vitreous China Urinals, half stall type white (excluding fjushing cistern, flush pipe and waste pipe complete including providing & fixing ;lugs bedding urinal against wall in cm 1:2 securing urinal to plug with bran screw all as specified and directed.

M&L painting to steel surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of red oxide including prepration of newly or previously untreated surface complete all as specified.

M&L painting to wooden surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of pink primer including prepration of newly or previously untreated surface complete all as specified.

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and Smooth mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric land on primed surface by torch application (c) third two coat of aluminium bituminous paint ( 200ml/sqm i.e 100 ml/sqm in each coat) over polymetric membrane complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in Hard / dense soil soil complete all as specified and directed.

Removing surplus soil obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

S&F Rotational moulded poly-ethylene three layes insunation puff water storage tanks (cylinderical vertical with closed top) 500 litres capacity, white in colour hoisted and fixed in position complete all as specified and directed.

supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete all as specified and as directed

supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete all as specified and as directed

S&F bib tap, cast copper alloy, screwed down high pressure with crutch of butter fly handle fancy type CP for 15 mm bore dia. GI tubing. Make 'somany' / 'L &K' complete all as specified and directed.

S&F PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified

S&F for in repairs 15mm angle cock chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified.

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed

S&F PVC (SWR) pipes, 75 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) pipes, 110 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed.

S&F Ball brass valves , high pressure , with polythene float and fly nut complete & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed.

M&L cast iron nahani trap 75mm dia with grating including jointing to wste pipe fixed in cement concrete type B1 (1:2:4) etc complete.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

M&L for cement concrete (1:3:6) type C2 using 40mm graded stone aggregate in bed to drain pipe including packing under and hunching against the sides of pipes after they are laid and tested complete for pipe size of 150mm bore.

M&L for 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars

M&L for providing cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in surfaces channels drains and benching including form work and finishing fair and smooth using extra cement (forming fair finished channel shall be measured and paid for separately)

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete sing extra cement including forms moulds, mitered stopped ends all as specified.

From work to edges of concrete flats exc 5mc and n.exc 10cm wide for rough finished surfaces of concrete.

M&L reinforced cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) on wall all as specified (reinforcement and form work shall be measured and paid separately)

M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone agg) as in cover slabs for man holes and set in CM 1:4 including necessary from work all as specified. Note: Reinforcement and form work shall be measured paid separately)

M&L for Chequered cement concrete tiles 20 cmx20cmx20 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

Surface excavation n.exc(not exceeding) 30 cm deep and averaging 15cm deep and getting out complete all as specified and directed.

M&L 16 to 18mm Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size not exceeding 0.25 sqm area set and jointed in cement and stone dust mortar 1:3 and pointed in cement mixed with aproved pigment to match complete all as specified and directed.

M&L for vitrified paver color tiles 30 cmx30cmx9 to 10 mm thick, moulded set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

Forming 12mm thick expansion joints filled with pre-formed bituminous filler and to 30mm primed and sealed with sealing compound, grade 'A'

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators, partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Cutting holes in brick/stone wall ,depth of embedment portion of hold fast n.exc half brick wall but not exc one brick wall, built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed

Excavating in posts holes (or similar holes) in hard/dense soil each n.exc 0.50 cu.m getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm watering, and removing surplus soil to a distance n.exc 50m and making good surface.

M/L for providing PCC 1:3:6 type C2 using (40mm graded stone aggregate) in foundation filling and mass concrete.

M&L Mild steel Angle iron for fencing post & strut in fencing including cutting tops to shape as directd all necessary drilling, bolting or riveting etc and similar work conforming to FE-290 Gde E-165.

Supply only, chain link fencing of MS galvanized fencing, any size or type.

Fixing only chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed Note : Supply only chain link fencing and line wire will be measeured and paid separately.

M&L Mild steel flat iron fillets (for securing wire mesh) including all necessary drilling, bolting or riveting etc and similar work conforming to FE-290 Gde E-165.

S&F mild steel round bars 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooking ends stiffeners confirming to FE-410-W ( Gde E 250) quality-A or Fe 290 (Gde E-165).

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other, or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut length of bolt exc 5cm but n.exc 10cm long and dia of neck 11 to 15mm.

S&F galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including, securing and tying at crossings with and provisions of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured).

S&F framed work (ornamental) as in steel gate of angle or other section with gusset plate ,rails braces etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hook and hinges and also fastening and fixing Fe-290 ( Gde-E-165) complete.

M & L Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint

M&L for precast cement concrete block masonry 1:3:6 type C-1 (using 20mm graded aggregate) with solid blocks exc 10cm in width and set in CM 1:6 complete all as directed and specified.

Point wiring with PVC insulated 1.5 sqmm multi stranded FRLS copper conductor cable 1100 volts grade drawn into and including surface rigid nonmetallic PVC conduit medium grade not less than 20mm (ISI marked) with all conduit fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes (duly painted with two coats of anti corrosive paint out side and two coats of aluminium paint inside) with 2.8 mm thick HYLAM brand laminated white bakelite sheet cover for mounting switches, sockets, fan regulators, etc and 1.5 sqmm multi strand copper conductor cable as continuous earthwire complete for the for one light point controlled by one switch.

Ditto item above but for One fan point controlled by one switch.

Ditto item above but for One 3 pin socket outlet 5 Amps controlled with one switch on the same board.

Ditto item above but for One 3 pin socket outlet 5 Amp controlled by one switch on independent board.

All as per item above but with 2.5 sqmm multistrand FRLS copper conductor cable for one 15 Amp socket outlet controlled by one switch on independent board and 1.5 sqmm PVC insulated multi strand copper conductor cable as continous earth wire complete.

S & F modular white cover plate with frame of 12 module

S & F modular white cover plate with frame of 06 module

S & F modular white cover plate with frame of 03 module

S&F Modular switch 1 way 06 amp single pole

S & F modular switch 16A, 1 way of 1 module

S & F modular socket 16A, 6 Pin of 2 module

S & F of modular socket outlet 6A-5 pin combined of 02 module

S & F of modular fan step regulator 120 W-2 module

S&F Ceiling rose 3 terminal/pvc/polycarbonate, isolated body.

S&F Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings incl LED Bulb 9W/10W complete. Make of Lamp Holder :- Cona,Leader, Havells. Make of LED Bulb :- Philips, Wipro, Havells.

S&F Ultra bright LED Tubelight fitting of 22 w incluing req length of 1.5 Sqmm PVC multistranded copper conductor for electrical connection all as specified and directed. Make :- Philips, Wipro, Havells.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 6 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed. Make: Philips, Wipro, Havells.

S & F ceiling fan 1200mm sweep, 230 Volts AC single phase, 50 Hz 3 blades, double ball bearing, down road etc BE 5 star rating energy saving complete with all fittings and accessories all as specified and directed. Make :- Usha, Havells, Crompton.

S&F Sheet metal enclosure MCB DB, single door , 08 way SPN, 240 volts with 200 Amps rated bus bar with blanking plates wherever required and I.P. 20 degree protection complete. Make :- Schneider, Havells, Legrand.

S&F MCB single pole 240 volts, 6 to 32 Amps 'B' Series complete. Make :- Schneider, Havells, Legrand.

S&F, MCB SPN 40 to 63 Amps, 240 volts 'B' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F MCB single pole and neutral 240 volts, 25 to 40 Amps complete. Make :- Schneider, Havells, Legrand.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe etc complete all as specified and directed.

Supplying & fixing twin core PVC insulated with aluminium conductor single strained cable 1100 volts grade of size 16 Sqmm 2 core.

M & L for house service bracket (hook type) complete with 3 mtr long GI pipe 40 mm dia GI pipe Med grade two Nos 90 degree bends MS hook and stay or guy complete incl taking down old unsv one all as specified and directed.

Point wiring with PVC insulated 1.5 sqmm multi stranded FRLS copper conductor cable 1100 volts grade drawn into and including concealed rigid nonmetallic PVC conduit medium grade not less than 19mm (ISI marked) with all conduit fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes (duly painted with two coats of anti corrosive paint out side and two coats of aluminium paint inside) with 2.8 mm thick HYLAM brand laminated white bakelite sheet cover for mounting switches, sockets, fan regulators, etc and 1.5 sqmm multi strand copper conductor cable as continuous earthwire complete for the one light point controlled by one switch.

Ditto item above but for One fan point controlled by one switch.

Ditto item above but for One 3 pin socket outlet 5 Amps controlled with one switch on the same board.

Ditto item above but for One 3 pin socket outlet 5 Amp controlled by one switch on independent board.

All as per item above but with 2.5 sqmm multistrand FRLS copper conductor cable for one 15 Amp socket outlet controlled by one switch on independent board and 1.5 sqmm PVC insulated multi strand copper conductor cable as continous earth wire complete.

S&F Switch piano flush button single pole one way 5 Amp complete. Make : Havells/Cona/Legrand.

S&F Switch socket outlet, 5 Pin, 6 Amp 2 in 1, flush type, universal complete. Make : Havells/Cona/Legrand.

S&F Switch socket combination , 5 Pin, 6 Amp 2 in 1, flush type, universal complete. Make : Havells/Cona/Legrand.

S&F Switch socket combination , 6 Pin, 5/ 16 Amp 5 in 1, flush type, universal complete. Make : Havells/Cona/Legrand.

S& F of 9/10 W LED 2Ft LED batten including LED tube rod having LED Batten suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with minimum 2.5 KV surge protection. Make :- Wipro, Philips.& Havells.

S&F Ultra bright LED Tubelight fittings complete of 18 w incluing req length of 1.5 Sqmm PVC multistranded copper conductor ro electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. Make of LED fittings :- Philips, Wipro, Havells.

S&F PVC type Wall mounted Ventilating Fans 150 mm sweep BEE 5 star rating energy saving including cutting of wall all as specified and directed by Engr - in - Charge. Make :- Havells/Usha/Bajaj.

Supply & fixing water heater storage type metallic outer body and stainless steel inner container, 25 Ltrs capacity, electric suitable for single phase, 50 Hz, AC Supply, 4 star rating, including all necessary fittings and fixture with minimum 1M of three core 2.5 sqmm twisted copper conductor cable PVC sheated, three pin plug top complete with necessary fittings and fixtures all as specified and directed. Make :- Usha, Havells, Crompton.

M&L for sub main wiring with 2 runx 6 Sqmm + 4 sqmm earth wire single core PVC insulated cable unseathed multistranded copper conductor LT 1100 volts grade FRLS cable IS-694 (ISI marked with valid CML No ) drawn in & icluding PVC conduit of dia not less than 25mm in concealed (ISI marked with valide CML No ) including its all fittings/accessoreis with one run single core copper cable 4 sqmm multistranded conductor (ISI marked with valide CML No) colour code as a earth continuity and connecting upto DB with suitable lugs all as specifed and directed. Make of Conduit & wire : Havells, Finolex, Polycab.

S&F sheet metal enclosure, single pole and neutral with a two pin and earth plug and socket with and including one single pole MCB 20. Amps, 240 volts,10 KA complete all as specified and directed. Make :- Legrand/Siemens/Scheider.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 16 Sqmm 2 Core. Make :- Finolex/Gloster/Polycab.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 40 mm dia for cable protection complete all as specified and directed.

S&F LED solar torch light consisting of Solar Panel 0.88 Watt and 17% efficient, Li-on battary capacity 2200 mAh, LED span life 50000 Hrs, Solar charging Time Min 8 Hrs, Size 320x121x121mm, Solar panel span life more than 5 Years, Protecing overcharging, Overdischarging. Overcurrent and shortcircuit complete all as pecified and directed

M/s Shree Ram and Sons

BHAGIRATH CONSTRUCTION COMPANY