SPL REP TO QTR NO 23/4 AND 17/1 AT MGSF, PROVN OF SEPTIC TANK AND SOAKAGE WELL AT ASCON NODE TELIBAGH AND HQ RTZ, SPL REP TO SEC FENCING AROUND BLDG NO 78 AND 79 LBS MARG, PROVN OF SEWAGE LINE NEAR BLDG NO P 135 AT TRG AREA AMC AND P/O TOILET ETC

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended works complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling fencing wire mesh of any type or size complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section embeded in concrete, brick work, masonary etc., including taking out embedded portion and making good disturbed gound complete all as specified and directed.

Dismantling barbed wire of any type or size complete all as specified and directed. Note :- Each line of wire to be measured

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and exc 1.5m but not exc 3.00 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc. 0.5 cum getting out, returning, filling in, and ramming earth or broken rubble mixed with earth around in layer n.exc. 25 cm including watering and removing surplus soil to a distance n. exc 50m and making good surface in soft/ loose soil complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material soils n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Removing surplus excavated material soils exc. 250m but n.exc. 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M & L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in leveling course, padding etc. complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 100, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves etc and similar works set in cement mortar 1:4 complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars upto 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in slab supported on wall, beams and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basements slabs, under reamed piles and mass concrete and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts and similar works complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished surface complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, coloumns and stanchions and similar works for rough finished surfaces complete all as specified and directed

S&F structural steel framed work with rolled mild steel sections as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde E-165) complete all as specified and directed.

M&L mild steel framed work such as posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting and/or welding etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only 3mm dia GI wire chain link fencing of mesh size 75x75mm and any type complete all as specified and directed. NOTE: Weight constant of fencing shall be fixed by BOO.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards rails, straining bolts, etc. including provn of galvanised mild steel binding wire of 0.9mm dia annealed complete all as specified and directed.

Supply only mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, 5 to 10mm dia of neck, length of bolts exc. 5cm but not exc 10cm long complete all as specified and directed.

S&F Concertina coil fencing with punched tape coil 450mm dia (at stretched position), made out of hot dipped, galvanised steel wire coated with CLR anti corrosive paint, making diamond shape barbs with 18 SWG sheet, spring core 2.5mm thick wire with tape 0.52mm thick and weight of each coil should not be less than 7.50 Kg, each coil should have 50 rounds and should covers 6 RM length, fixed over and including 6 lines of horizontal RBT (reinforced barbed tape) wire or razor wire at points wherever coil touches the bottom of wire with the help of hog rings (14 SWG) and in between Y shaped angle iron post complete all as specified and directed. NOTE: (i) Hogging shall be fixed at a interval of 600mm centre to centre, wherever it touches with the razor wire. (ii) Overlapping of concertina coil and razor wire shall be 300mm. (iii) Y shaped angle iron post shall be measured and paid separately under respective items. MAKE: M/s Global Engg or M/s Specials steels Ltd or M/s Super Fence or other equivalent make as approved by GE.

S&F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provn of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed. NOTE: Each line wire to be measured.

M&L mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F steel ventilators with top hung shutters including box type hinges or factory made butt hinges with steel handle and steel peg stays etc. complete all as specified and directed.

M&L mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintel hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made Solid PVC door frame of size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.)

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for Top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 28mm thick made from co-extruded three layer rigid foam sheet (Single extruded) with 0.8 to 1mm thick decorative laminates both sides having density not less than 1400Kg/Cum and density of central core not less than 600 Kg/Cum manufactured by ann ISO 9001-2015 certified co. as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 19mm thick made from co-extruded three layer rigid foam sheet (Single extruded) with 0.8 to 1mm thick decorative laminates both sides having density not less than 600Kg/Cum and density of central core not less than 600 Kg/Cum manufactured by ann ISO 9001-2015 certified co. as per specification & drawing complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 2nd class hard wood (Sal) plain, solid, straight chowkhats and frmaes, wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints complete all as specified and directed.

S&F powder coated Anodised Aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for foxong etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

S&F powder coated anodized aluminium glazed window shutters, top hung type, using 1.50mm thick aluminium section having frame of size 65x38x1.25mm, including necessary jointing cleats, glazing clips, rubber neoprene packing, anodized aluminium snap beading screws, anodized aluminium fittings such as 02 nos 100mm long aluminium hinges B-21 type, 01 no 100mm long aluminium tower bolt, 01 no aluminium handle in each shutter complete all as specified and directed.

S&F powder coated anodized aluminium gauzed window shutters, top hung type, using 1.50mm thick aluminium section having frame of size 65x38x1.25mm, including stainless steel wire cloth 0.36mm dia of wire and average width of aperture 1.4mm, fixed with screws, with necessary jointing cleats, glazing clips, rubber neoprene packing, anodized aluminium snap beading screws, anodized aluminium fittings such as 02 nos 100mm long aluminium hinges B-21 type, 01 no 100mm long aluminium tower bolt, 01 no aluminium handle in each shutter complete all as specified and directed.

S&F powder coated anodized aluminium window and ventilator shutters, fixed type, using 1.50mm thick aluminium section having frame of size 65x38x1.25mm, including 4mm thick pin headed/tinted glass fixed with screws, with necessary jointing cleats, glazing clips, rubber neoprene packing, anodized aluminium snap beading screws, complete all as specified and directed.

S&F powder coated anodized aluminium glazed and gauzed window shutters, sliding type, three track (two of glass and one of stainless steel wire cloth) without sash bars, with aluminium sections weighing not less than 0.55kg/m and three track aluminium sections of size 100x38x1.50mm of including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, fibre wheel rollers, anodized aluminium fittings such as hinges, tower bolts and handles etc. including glazed with 5mm thick tinted glass and wire meshed with stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed.

S&F 100mm size stainless steel, butt hinges, medium weight and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 200mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L for 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 150mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F in repair 18-20mm dia mild steel PVC coated curtain rod, superior quality, any colour, with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

Dismantling wall and ceiling boards (Fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets complete all as specified and directed.

S & F 18/19mm thick 1st quality plywood interior grade both side with commercial face, grade BWR, type BB fixed with screw/ nails to timber frame work edge chamfered complete all as specified and directed.

M&L 0.80mm thick decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finished or electro galvanised, with width of flap 30mm when open, and fixed with screws complete all as specified and directed.

S&F 40mm dia, cupboards knobs, decorative, fixed with nut, screws and washer of mild steel, bright finished complete all as specified and directed.

S&F Ball catches (magnet catcher) with 8mm dia steel ball, brass body and striking plate including letting in, overall size 50x15mm and fixed to shutter complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surface of ceiling and finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for bearing plaster 20mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 10mm thick in CM 1:3 on roof surface using 100% coarse sand with integral water proofing compound @ 3% by weight of cement, finished surface even and fair complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of oil bound distemper on previously treated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of cement based paint on previously treated plastered surfaces of wall over one coat of primer including preparation of surfaces complete all as specified and directed.

M&L for two coats of oil bound distemper on previously untreated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

M&L for two coats of white wash on old plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M & L for preparation of surface of wall/chajja and applying a coat of Tapecrete P-151/Cemcrete acrylic polymer modified cementitious slurry consisting of one part of TAPECRETE P151, two part of cement by weight complete all as specified and directed

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description not exc 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described and treating small articles such as stop, covers, gully gratings, holdfasts, end of posts, back of chowkhats, etc. area n. exc. 0.1sqm each and treated with tar or coal tar black paint complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc. finished even and fair without using extra cement complete all as specified and directed.

M & L Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3,complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free glazed ceramic tiles, coloured, superior quality of size 350x250x7mm/ 450x350x7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick(square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick(square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including rendering of mortar 10 mm thick in cement mortar 1:4 finishing surface even and rough to receive tiles complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick screed bed in cement mortar 1:4, including rubbing, grinding, making hole for gas pipe line and including making sandwitch moulding to edges complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, including rubbing, rubbing, grinding and including making round moulding to exposed edges complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in partiotion to cupboards including rubbing, grinding and including making round moulding to exposed edges complete all as specified and directed.

S&F Exterior finish floor tiles of appproved size 10 to 12mm thick, superior quality, approved shade, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Make: Endura/ Duracrete/ Naveen/ Eurocon/ NITCO.

Taking up or down 15mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

Taking up or down 20mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

M & L Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 10cm in girth complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Taking down eaves gutters rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks, etc. including cleaning for refixing or removal from site (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single T), equal suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with gratings including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

S&F 100mm bore cast iron sand cast soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore cast iron sand cast soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

S&F cast iron bends of any radius diminishing pieces or tapers, suitable for 100mm bore CI pipes, fixed and jointed with cement mortar complete all as specified and directed.

S&F cast iron bends of any radius diminishing pieces or tapers, suitable for 75mm bore CI pipes, fixed and jointed with cement mortar complete all as specified and directed.

S&F 75mm bore cast iron, single T, equal or unequal, ordinary or inverted (spigot or socketed type) or with parellel branches jointed with cement mortar complete all as specified and directed.

S&F cast iron floor trap, with gratings including jointing to waste pipe fixed in cement concrete type B1 1:2:4 for 75mm bore of outlet complete all as specified and directed.

S&F 75mm bore cast iron sand cast soil waste and vent pipes in any length with or without ears with cement joints fixed to walls with MS clamps complete all as specified and directed.

S&F 75mm bore cast iron cowl complete all as specified and directed.

S&F in repairs bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F vitreous china Wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F In repairs vitreous china Wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F pillar taps 15mm bore, half/quarter turn, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered HOT or COLD with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F central hole basin mixer, quarter turn, fancy type, brass chromium plated, with round spout with popup waste system, including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed. Make: Jaquar Essco cat no. TQT516A or Hindware cat no. F280009CP.

S&F in repairs Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated or aluminium hinging device ISI marked as approved complete all as specified and directed.

S&F Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F vitreous china urinal, bowl type, flat back of size 465x355x265mm white, with grating and union for discharge pipe (excluding flushing cistern and flush pipe), including waste pipe, providing and fixing plugs, bedding urinal against wall etc. complete all as specified and directed.

S&F 500 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F in repairs 500 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified and directed.

S&F 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F wall mixer with over head shower with hot and cold valve arrangement, connecting legs and wall flanges, fancy type, brass chromium plated, with costed swinging spout including plugging and securing to walls suitable for 15mm bore pipe complete all as specified and directed. Make: Jaquar Essco cat no. TQT517B or Hindware cat no. F280018CP or Parryware cat no. G3316A1.

S&F 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F urinal spreader 15mm bore, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories for half stall type urinal complete all as specified and directed.

S&F angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs brass chromium plated overhead shower rose with arms, 125mm size, round shape, single flow, fancy type, suitable for 15mm bore pipe and fixed complete all as specified and directed.

S&F in repairs hand shower (health faucet), superior quality, round shape, single flow, brass chromium plated, with 1m long chrome finish flexible pipe with wall hook bracket etc. and all fittings for EWC complete all as specified and directed.

S&F CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repairs CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F 5.5mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F 5.5mm thick sheet glass corner shelf assembly, fancy type, sheet glass shelf of size 250x250mm, with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F peg set of 6, brass chromium plated, fancy type, with 40mm wide brass CP strip, fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repairs CP brass soap dish , fancy type, as per sample approved complete all as specified and directed.

S&F in repairs CP brass toilet paper holder, fancy type, with wall hook, bracket complete set as per sample approved complete all as specified and directed.

S&F in repair stainless steel sink with drainage board made out of 1mm thick sheet with plugs, washers incl brackets fixed to wall and connecting union to pipe overall size 1145mm x 510mm, bowl size 560x410x200mm including PVC waste pipe and waste coupling 40 mm dia complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack (utensil rack) of size 750x600x250mm, made out of 0.63mm thick stainless steel sheet, approved design and fixed to wall with brass screws and PVC gully including all necessary fittings like nuts and bolts etc complete all as specified and directed.

M&L for 150mm bore salt glazed stoneware drain pipes, complete with collars, laid in trenches and jointed in cement mortar 1:1 as in drains complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete foundation bed to 150mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains, making good to 150mm bore pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L provn of roof treatment with polymeric water proofing membrane all as given below:- (a) Taking down existing roof treatment of any description and removal of waste material from site. (b) M & L for rendering 10mm thick in cement mortar 1:3 on roof incl WPC as per manufacturers instructions. (c) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (d) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (e) M&L for applying two coats of aluminium paint on membrane @ 0.10 Kg/Sqm (each coat) complete all as specified and directed.

M & L for painting building plaque with background using black synthetic enamel paint and building number with white synthetic enamel paint, overall area of plaque exc 0.1 sqm but not exc 0.4 sqm complete all as specified and directed.

M&L for construction of Septic Tank suitable for 100 users with RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in bases, baffle walls, beams, roof slab, cover slab, covers etc., brick work with old size fly ash bricks in CM 1:4 and manhole cover made out of 6mm thick MS steel sheet and frame of angle iron 50x50x6mm including all required earthwork in soft/loose soil, cement concrete etc. complete all as shown on CELZ drawing No. TD/687 sheet 1/2 & 2/2 amended upto date complete all as specified and directed. Note : Depth of septic tank shall be the effective depth i.e. below invert level of sewage line

M&L for construction of Septic Tank suitable for 50 users with RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in bases, baffle walls, beams, roof slab, cover slab, covers etc., brick work with old size fly ash bricks in CM 1:4 and manhole cover made out of 6mm thick MS steel sheet and frame of angle iron 50x50x6mm including all required earthwork in soft/loose soil, cement concrete etc. complete all as shown on CELZ drawing No. TD/687 sheet 1/2 & 2/2 amended upto date complete all as specified and directed. Note : Depth of septic tank shall be the effective depth i.e. below invert level of sewage line

M&L for construction of Septic Tank suitable for 25 users with RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in bases, baffle walls, beams, roof slab, cover slab, covers etc., brick work with old size fly ash bricks in CM 1:4 and manhole cover made out of 6mm thick MS steel sheet and frame of angle iron 50x50x6mm including all required earthwork in soft/loose soil, cement concrete etc. complete all as shown on CELZ drawing No. TD/687 sheet 1/2 & 2/2 amended upto date complete all as specified and directed.Note : Depth of septic tank shall be the effective depth i.e. below invert level of sewage line

M&L construction of Soakage Well of size 2.40m dia and 6.00m effective depth with fly ash bricks and RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in cover slab etc. including all required earthwork in soft/loose soil, filling of brick bats and cement concrete etc. complete all as shown on CELZ drawing No. TD/576 sheet 1/2 & 2/2 complete all as specified and directed.

M&L construction of Soakage Well of size 2.40m dia and 4.50m effective depth with fly ash bricks and RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in cover slab etc. including all required earthwork in soft/loose soil, filling of brick bats and cement concrete etc. complete all as shown on CELZ drawing No. TD/576 sheet 1/2 & 2/2 complete all as specified and directed.

M&L construction of Soakage Well of size 1.20m dia and 4.50m effective depth with fly ash bricks and RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in cover slab etc. including all required earthwork in soft/loose soil, filling of brick bats and cement concrete etc. complete all as shown on CELZ drawing No. TD/576 sheet 1/2 & 2/2 complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 175 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 175 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item no 175 above but for one call bell/buzzer point controlled by one bell push

All as per item no 175 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F Switch bell push, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F call bell, ding dong type, AC single pole, 230 volt complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F sheet metal enclosures with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 Volt, 10 KA breaking capacity complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 8 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 4 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F in repair ceiling fan regulator, electronic, rotary step up socket type, 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

Taking down existing electric meter of any type and capacity and fixing back to location as directed including making all electric connections complete all as specifed and directed.

Taking down existing ceiling fan, exhaust fan or geyser of any type and capacity and fixing back to location as directed including making all electric connections complete all as specifed and directed.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 2.5sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S & F in replacement 1100V garde heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection cable flat or circular stranded 6Sqmm aluminium conductor complete all as specified and directed.

S&F wall mounted 9/10 W LED integrated mirror light fitting, 600mm long batten with extruded aluminium housing & integrated electronic driver and one no. 9/10 W LED, 6000 K, 230V tube light including and provn of connection from ceiling rose to luminaries with suitable size three core flexible copper wire complete all as specified and directed. Make: Havells cat no. LUMILINE PLUS BS 10WLED865SPCSS or Surya Visco cat no. SLE BT 10 or C&S cat no. LTDC01210WLED/WD or Philips cat no. BN 021LED 12S6500/4000 PSU GR/SI.

S&F in repairs LED building security light fitting of 24/25 W with high power LED source (more than 110 lumens/ watt), PDC housing, IP65 and IK 07 with 4KV inbuilt surge protection driver, with all accessories, prewired and fixed to bldg/pole including GI bracket 0.60m long bent to shape, made out of 40mm dia GI light grade pipe with nuts, bolts and washers and provn of connection from ceiling rose to luminaries with PVC 3 core flexible copper wire complete all as specified and directed. Make: Philips cat no. BRP042LED25CWR1S1 PSU GR. / Bajaj Edge nxt LED Cat No. ENXT P 24L WH CR PC SD/Eveready Mini might Cat No. LED SL025157-02

S&F wall light with Decorative wall light fixture made up of Polycarbonate, (Spiral B-22 base), with and including 01 No. 9 W LED Bulb, 230 V, 6000K, complete incl all required electrical connections arrangements complete all as specified and as directed. Make Havells code : CITY 1 LHDL02160099 / Bajaj ordering code: BJLF1 15W RF/ Mepro cat No. AL-135 ( Note: Rates incl 01X 9 W LED Bulb with each fitting)

S&F FTL fittings with decorative LED batten made up of aluminium casting 18/20 W of size 1200 mm complete standard fittings and fixtures including fixing on walls/roofs with fitting arrangement including neccessary electric connection from ceiling rose to luminaries with suitable size PVC cord complete all as directed. Make: Havells cat Part No. REGALBATTEN8UPTO1X22WDSBSWH/ Surya Batten cat Part No. SUB118 T8 LED/ C&S (CRUX) cat Part No. LTICIX161820W LED/ Philips cat part No. TMC 100 1xT LED 13-20W WH

S&F FTL with ultra bright crystal LED tube rod, 18/20 W, 6000 K with high efficency including neccessary electrical connection by disconnecting old elecronic ballast connection if required complete all as directed. Make HAVELLS cat Part No. CRYSTAL1213T8DSTL20WLED865SGLASS/ Surya LED TUBE cat Part No. SLE TL DS 18 GL/ C&S (CRUX) cat Part No.LT4F20WLEDT-8/WD/ Philips cat part No. 20W 865 T8 IND

M/S Reliance Construction