CONSTR OF GD ROOM WITH ATT TOILET AND STORE IN GEN AREA NIRMALI KUND AT DRC AYODHYA

Amount

Surface dressing n exc 30cm deep and avaraging 15cm deep and getting out in any type of soil complete all as specified.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc in any type of soil and getting out complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers n. exc 25cm thick all as specified.

Removal of excavated material soil n. exc 50m and depositing where directed at a level n. exc. 1.5 above the starting point all as specified.

M&L PCC 1:4:8 type D-2 using 40mm graded agg. as in foundation filling and mass concrete complete all as specified.

M&L for reinforced cement concrete (nominal mix) using 20 mm graded Type B1 1:2:4 in foundation, including, including rafts, footing, foundation beams, plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete.

M&L for reinforced cement concrete (nominal mix) using 20 mm graded Type B1 1:2:4 in Columns, pillar, piers, posts and struts.

M & L for reinforced cement concrete (nominal mix) using 20 mm aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M & L for reinforced cement concrete (Nominal mix) using 20 mm aggregate in beams, cantilevers, shelves, bressummers, lintels over 1.5m span

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter - Rough finished surfaces of concrete - Flat

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions - Rough finished surfaces of concrete - Square, rectangular or polygonal

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) - Rough finished surfaces of concrete - Flat

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc - Rough finished surfaces of concrete - Flat

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified .

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for Brickwork with sub- class ‘B’ bricks straight or curved on plan exc 6 m mean radius in CM 1:6

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed including cutting chases, pinning in brick work for concealed water tubing and making good complete to walls all as specified. Make Jindal, Tata and Prakash

S&F Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors - Bore of tube 20mm. Make Jindal, Tata and Prakash

M&L for rendering 15 mm thick on fair faces of brick work in CM in 1:4 finished even and fair and mixing with water proofing liquid as per manufacturer instruction (but excluding the cost of water proofing liquid ) external surface all as specified. Note- Rendering shall be done by coarse sand only

M&L for rendering 5 mm thick in CM 1:3 on concrete surface in ceiling Note- Rendering shall be done by coarse sand only

M&L for rendering 10mm thick in CM (1:6) on Brick/ Conc surface finished even and fair on internal surfaces of wall. Note- Rendering shall be done by coarse sand only

M&L for preparing the new plaster surface and applying two coats of OBD on ceiling all as specified.

M&L for 1-2 mm thick putty with two coats of weather coat paint over a coat of primer over prepared surface of wall complete all as specified.

M&L for preparation of new plastered surface and applying two coat of oil bound distemper on walls over a coat of primer incl 1mm thick wall care putty complete all as specified and directed.

M&L for broken stone or boulder hardcore of guage n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface

M&L 75 mm thick PCC 1:4:8 as in sub base of floors etc and finishing the surface even and smooth without using extra cement complete all as specified.

M&L for 75 mm thick cement concrete (1:3:6) type C-1, using 20mm graded crushed stone aggregates as in plinth protection in panels, including finishing the surfaces even and fair.

M&L for Coloured Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and incl 10mm thick plaster in cement mortar (1:4) complete all as specified and directed. Make:- Johnson, Kajaria, Orient Bell

M&L Machine cut kota stone slab flooring 15 to 18 mm thick over cement screed bed in CM 1:6 15 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Note-

M&L Machine cut kota stone slab skirting 15 to 18 mm thick over 10 mm thick rendering in CM 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L Non skid ceramic colour tiles 7 to 8 mm thick ( sq/ rect) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Make Somany, Kajaria, Orient Bell

S&F pressed steel frame for doors made out of MS sheet 1.25mm thick of size 125x60mm for with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkhats all as specified. Make : NCL All tech Ltd, Ashish Industries, Trishul Industries

S&F 30 mm thick prelaminated moulded designed door on both side complete all as specified and directed. Note : Designed/colour shall be approved by Engineer-in-Charge.

S & F 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain, chamferd or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.24(a), etc complete all as directed by Engineer-in-charge. Make : Century Plyboard, A-1 Teak Product, MP Wood Product

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one pink primer complete all as specified.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain color PVC sheet reinforced with MS square tube complete all as specified & directed. Make Rajshree, Yamuna Interior or equivalent

S&F for Factory Made Solid panel PVC door shutter, 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails, MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement all as per specification and drawing and as directed. Make Rajshree, Yamuna Interior or equivalent

M&L for 4.8 mm thick sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for 4.8 mm thick frosted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

S&F Stainless steel wire cloths 0.56mm nominal dia and average width of aperture 1.18mm & fixed with tint tacks or glavinized wire staples complete all as specified and directed.

S&F 300mm ordinary mild steel springs ISI marked including roller and roller plate complete including all necessary welding if required.

S&F Stainless steel sliding door bolt 300mm long with hasp, staple (bolt type) and fixed complete all as specified and directed.

S&F Vitreous china urinal bowl type or half stall pattern white (back or corner wall type) with spreader complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe grating and union for discharge. Make : Parryware, Cera, Jaquar

S&F 150mm long stainless steel tower bolts of extruded section ISI marked

S&F 150mm stainless steel handle complete all as specified as directed.

S&F 100mm long butt hinges stainless steel complete

M&L for 10mm thick rendering in Cement mortar 1:4 mixed with WPC 3% by weight of cement on fair faces of concrete roof surfaces , finished even and fair to receive treatment on roof complete all as specified and directed.

M&L for water proofing treatment to roof surface with APP water proofing membrane 3mm thick & weighing not less than 3.00 Kg/Sqm of approved make black finish and reinforced with non woven polyester matt of min 150 gm/sqm laid over a coar of bitumen primer conforming to IS-3384 @ 0.4 Ltr/Sqm over prepared roof surface, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100 mm at ends & sealing as per manufacturer instruction over and including two coat of aluminium paint complete all as specified and directed.

S&F 15 mm bore Angle/Stop valves, cast copper alloy, screwed chromium plated fancy type down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make:- Essco, Jaguar-ESSCO,Grohe,Kholer

S&F 15mm bore concealed stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle, fancy type with chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. Make:-Essco, Grohe,Kholer

S&F 15mm bore bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle fancy type chromium plated screwed for iron pipe for brass furule and fixed complete all as specified and directed. Make:- Essco, Grohe,Kholer

S&F for CP Soap Dish fixed with and incl CP screws of as approved by Engr-in-Charge.

S&F Tubular towel rail 20mm dia ‘D’ type 60cm long between flanges brass chromium plated.all as specified and approved.

S&F rotational moulded polythene water storage tank double layered (outer layer black and inner layer white colour) (Cylindrical vertical with closed top hoisted fixed in position all as specified capacity of tank 1000 ltrs including inlet and out let connections 20 mm air and 15 mm dia GI pipe medium grade including 20 mm gate valve. Make Vectus, Syntex, RC plasto

S&F 20mm PTMT ball valve high pressure with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified. Make Prayag, Nirali or Jain Brother sanitation

S&F Vitreous china wash down water closet pedestral pan white, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, Plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed. Make Jaquar, Cera and Parryware.

S&F vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling of 32 mm size fixed in repair complete all as specified and directed by Engineer-in-Charge.Make:-Parryware, Jaquar, Hindware

S&F Brass chromium plated shower rose 125 mm size and fixed complete all as specified and directed. Make Prayag or equivalent

S&F, PVC connection 15mm bore size with two nuts and washers of length 450mm all as specified and approved.

S&F for 110 mm PVC (SWR) junction single, (Single T) equal or unequal

S&F for 110mm bore pipes,PVC (SWR) bends any radius fitting fo PVC (SWR) pipes as in repair complete all as specified and directed.

S&F, 110mm bore, PVC rainwater (SWR) drainage pipes single socketed, in any length with rubber ring joints as in repair, fixed to walls with sufficent number of Iron stack clamp complete all as specified and directed. Make Finolex, Astral and Prince

S&F, 75mm bore PVC floor trap with grating including jointing to waste pipe in cement concrete type B-1, 1:2:4, complete all as specified and directed.

S&F for 75mm bore pipes,PVC (SWR) bends any radius fitting for PVC (SWR) pipes as in repair complete all as specified and directed.

S&F for 75 mm PVC (SWR) junction single, (Single T) equal or unequal

S&F of 75mm PVC (SWR) drain pipes 75 mm bore single socketed in any length with rubber ring joint fixed to walls/floor complete all as specified and as directed. Make Finolex, Astral and Prince

S&F fancy type drapery rod 20 mm dia mild steel, chromium plated with fixing brackets, incl side brackets, finials complete complete all as specified.

S&F 18 mm thick PVC board single side prelam/Rigidlam colour fixed with epoxy coated screws, solvent cement/ adhesive to make cupboard cabinet sides, top and bottom and shelves inside the cabinets complete all as specified and directed (Density - 575 to 600 Kg/CBM)(Make Rajshri plastiwood or equivalent in make as specified in PS)

S&F magnetic catcher of size 20 mm X 50 mm suitable for cupboard shutter complete all as specified and directed

S&F auto closing hydraulic (soft closing) chrome finish stainless steel hinge openable at 110 degree all as specified and directed.

Supply only 75 mm dia oval shape brass handle fancy type polished bright finish complete all as specified and directed

M&L MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work conforming to Fe.290.Gde-E-165

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

M&L for treating the backfill in contact with foundation at the rate of 7.5 Lit of emulsion per square metre of vertical with backfill to be measured)

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre

S&F for 150mm dia bore reinforced concrete pipe, class NP2, laid and jointed with collars in cement joint complete all as specified and directed.

M&L for 2.4m dia and 3.00m effective depth of soakage wells excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M25 concrete including interceptig chamber and screen chamber made of brick masonry in CM, RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4m dia and 3.00m effective depth complete all as specified and directed by Engr-in-Charge

M&L providing cement concrete type B1, 1:3:6 (20 mm graded aggregate) surface channels, drain etc complete all as specified and directed.

Removal of excavated (Soil) to a distance exc 100m but not exc 200m and depositing where directed at a level not exceeding 1.5 metre above the starting point all as specified.

M&L Mild steel TMT steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate ) as in bed to drain pipes including packing under and completely surrounding pipe with concrete after they are laid, jointed and tested for 150mm dia bore of pipe complete all as specified and directed.

M&L precast RCC 1:2:4 type B1 (20mm graded stone aggregate) as in cover slab for manholes etc chajjas, mangers, shleves etc in CM 1:6 complete with joints to match complete

M&L for 10mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces finishing the surfaces even and smooth without using extra cement all as specified.

M&L PCC 1:2:4 Type B1 (20mm graded aggregate) in lintel upto 1.5m clear span, cill, step , seismic and other similar bands, plinth course, string courses, lacing course parapets and railing upto 60 cm in height, bed plates, coping, kerb etc water troughs and the like included weathering, slightly rounded or chamfered angles and throating as directed.

Providing and fixing factory made uPVC white colour sliding window three track made of extruded profiles with wall thickness of 2.3mm(+ - 0.2 mm). Window profile with hollow section with multi chamber.Frame (88 mm x 52 mm),sliding sash (42 mm x 67 mm ).Sliding mesh Sash (42 mm x 57 mm) Slide interlock (One vertical length in each shutters )(45.5 mmx 28 mm ),Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners,including railing of holes for fixing hardware and drainage of water etc. making arrangement for fising of hardware.EPDM gasket 1.2 + - 0.2mm thick galvanized steel frame (30mmx18 mm) 2 No.s ,sliding sash(30 mm x 18 mm),sliding mesh sash (26 mmx 10 mm) profile to be inserted in required profile ,frame will be fixed to wall with 8 mmx100 mm long fasteners.HardwareTouch lock of zinc alloyed (white powder coated ),steel roller system ,stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories .(Note:The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.Net opening will be measured for payment purpose.)Area n exc 2.00 Sqm Each

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

75 mm thick PCC M-10 (nominal mix) as in floor surface finished even and fair without using extra cement all as specified.

M&L 60 mm thick coloured rubber moulded,glossy finish machine pressed interlocking paver block of any shape with grey cement and pigment size conforming to IS 15658-2006 of 60 mm thickness,M-35 Grade laid over sand cushioning. Note :- sand shall be measured and paid separetly.

Supply only sand filling under floors all as specified and directed by Engr-In-Charge

M&L for PCC 1:2:4, Type B0 (12.5MM graded aggregate) for coping and similar item complete all as spd and directed.

M&L point wiring complete for one light / fan/ exhaust fan point controlled by one switch with PVC insulated and unsheathed, FRLS-H cable 1.5 sqmm (nominal area), ISI marked, multistranded copper conductor cable single core including ISI marked not less than 20 mm dia medium grade PVC conduit ISI Marked concealed in wall, roof floors, factory made pressed steel concealed terminal boxes not less than 1.6 mm thick of reqd size including 1.5 sqmm PVC FRLS-H cable insulated unshethed multi stranded copper earth wire to the common earth and connecting to earth dolly including colour coding shall be phase-red, Neutral- Black, and Earth - green with all accessories complete all as specified and directed. Make of copper conductor :- KEI/Havells/Polycab.

All as per Item No 92 of above but for one 5 pin socket outlet 5 amps on same board complete all as specified and directed.

All as per Item No 92 of above but for one 5 amps socket outlet independent board complete all as specified and directed.

M&L point wiring complete with PVC insulated and unsheathed, FRLS-H cable 2.5 sqmm (nominal area), ISI marked, multi stranded copper conductor single core including ISI marked not less than 20 mm dia medium grade PVC conduit ISI Marked concealed in wall, roof floors, factory made pressed steel concealed terminal boxes not less than 1.6 mm thick of reqd size including 2.5 sqmm PVC FRLS-H cable insulated unshethed multi stranded copper earth wire to the common earth and connecting to earth dolly including colour coding shall be phase-red, Neutral- Black, and Earth - green with all accessories complete all as specified and directed.Make of copper conductor Make:- KEI/Havells/Polycab.

S & F switch piano flush type one way 6 Amps

S&F switch piano, flush type, one way, 16 Amps

S & F socket outlet 5 pin, 6 Amp flush type

S&F socket 2 in 1, 3 pin, 5 and 16 Amps flush type complete all as specified and directed.

S & F ceiling rose surface Bakelite three terminals

M & L for Sub main wiring with two single core 6 sqmm FRLS-H copper conductor, PVC insulated, multi stranded, unsheathed cable ISI marked drawn in conduit concealed in wall surface / ceiling for sub main connection including 6 sqmm PVC insulated multi stranded unsheathed copper conductor used as earth wire to common earth and connection to earth dolly complete all as specified. Note:- (i) Two single core 6 sqmm copper conductor, one run PVC conduit and one run of 6 sqmm earth wire shall be considered & measured as one unit.

S&F epoxy powder coated MCB, DB, double door TPN horizontal 4 way for MCBs with common bus-bar at incoming end of outgoing MCBs grouted/ flush to wall all as directed.

S & F in Proper Position MCB TPN of capacity 63 Amps, 415 Volts C series with 10 KA breaking capacity, including necessary connection complete all as specified and as directed.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed.

Supply and fixing indoor luminaire batten for wall/ceiling mounting box type energy efficient saving LED BATTEN LIGHT 20 W incl twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repair lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply & fixing steel body exhaust fan 300 mm sweep AC 230 volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified.

Supply and fixing ceiling fans complete with three blades, down rods, accessories, 230 V, 1200 mm sweep 5 star rated with brushless direct current motor (BLDC) with remote including making connection with three core pvc insulated 100 volts graded multistranded copper wire of appropriate size including testing complete all as specified

Supply and fix electric water heater, storage type steel body with stainless steel inner tank material ,shock proof,auto cut,on off,thermoplastic body corrosion free and heating element of 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground (earth pit) not less than 2.25 meters deep below GL with top edge of earth plate not less than 1.50 m below ground level, connected to GI lead wire of 4 mm dia. (7.50 m long) by means of nuts, bolts and washers, check nuts of GI and protected by the GI pipe light grade 1.5 mm nominal bore (7.50 m Long) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick CI funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, PCC 1:2:4 type B1 earth pit and Precast RCC cover 50 mm thick dully reinforced with 6 mm dia, MS round bars @ 100 mm C/C both ways, earth testing point, making good to floor complete all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core.

M & L for sand cushioning to underground cable with clean dry river sand complete all as specified and directed by Engr-in-Charge. Note:- Punned thickness only shall be measured & Paid.

Supply & Laying of sub class 'B'bricks locally available best quality laid flat (length of bricks laid across the length of cable) in tranches for protection of U/G cable complete all as specified and directed by Engr-in-Charge.

Supply,Laying, testing and jointing Galvanised steel water tubing 50 mm bore with screwed socket joints medium grade,together with all fitting (such as bends , elbows, tees, short pieces , connectors, back nuts, diminishing pieces, caps , wooden plugs or laid in floors including , screwing and waste and for forged bends on piping as required, cutting through walls, floors and their making goods to match with the existing specifications complete all as specified and as directed Make - TATA/ JINDAL/ PRAKASH/ZENITH

Supply,Laying, testing and jointing Galvanised steel water tubing 25 mm bore with screwed socket joints medium grade,together with all fitting (such as bends , elbows, tees, short pieces , connectors, back nuts, diminishing pieces, caps , wooden plugs or laid in floors including , screwing and waste and for forged bends on piping as required, cutting through walls, floors and their making goods to match with the existing specifications complete all as specified and as directed Make - TATA/ JINDAL/ PRAKASH/ZENITH

Supply and fix in repairs 50 mm dia gate valve (Gun metal glove valve ) with iron wheel head , screwed both ends for iron pipe and fixed for, complete all as specified and directed. Make-Scud/leader/Zoloto. Note : The quoted rate is deemed to be inclusive of cutting , threading , insertion of union joint , nipple etc for required size of pipe.

Supply and fix in repairs 25 mm dia gate valve (Gun metal glove valve ) with iron wheel head , screwed both ends for iron pipe and fixed for, complete all as specified and directed. Make-Scud/leader/Zoloto. Note : The quoted rate is deemed to be inclusive of cutting , threading , insertion of union joint , nipple etc for required size of pipe.

Supply & installation of High galvanized mast light 15 meter long suitable for 8 lantern symmetrically fitted along with their control gear and having two point suspension system with stainless steel wire rope of 6 mm dia 97/19 guage and double drum winch with luminaire mounting arm, pully assembly, aviation obstruction light, lightning arrester spike, motor with starter including RCC foundation as per height Complete all as specified and directed.

Supply and fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

S&F in repair aviation obstruction LED light luminaire with clear thick glass and accessories complete all as specified. Make: Philips / Crompton / Bajaj / Havells

S & F Automatic street light switch using Nature Switch for automatic switching of street lights based on lux level of natural light. The sensor (Nature Switch) alongwith and including supply and fix of suitable power contactor of 1 Nos 40 Amps (four pole ) three Nos MCB 63 Amps (single pole) and support terminals enclosed in pole /wall mountable enclosure of suitable size made out of rust proof electric shock proof termite proof and FR grade special moulding compound sintex make SMC junction box of suitable size confirming to IP54 circuit wiring suitable enough to take load of 12 KW load equally distributed over three phase load, all as per Kadatiya Energy System Ltd Hydrabad Model SWADEEP 02EC-12KW3P or techno commercially equivalent models in Havells/ L & T complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60x60cmx 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.25 mtr below normal ground level,connected to galvanised 32 mm x 6 mm earth strip by means of nuts,bolts, washer of GI steel as shown on electrical plant No 3 of MES schedule part I connected to earthing test point and testing on completion with including necessary excavation and earth work, earth electrode, earthing lead from electrode to equipment /substation , adequate quantity of charcoal dust and comman salt , test point pcc (1:3:6) type C-I (using 20mm graded black trap/granite/basalt stone aggregate) for earth pit with 40x40x6mm mild steel angle iron frame for cover,pre-cast RCC (1:2:4) type B-I (using 20mm graded black trap/granite/Basalt stone aggregate) 40mm thick cover, reinforced with 6mm dia bars 3 Nos both way with 12mm dia round bar handle, GI light grade watering pipe 15mm dia with funnel and wire mesh, and 40 mm dia GI light grade earth lead protection pipe, 7.5 mtr only from the top of earth electrode are deemed to be included under this item and additional earth lead, if any, required at site shall be measured and paid for seperatly under appropriate item of schedule `A'. complete all as specified and as directed by Engr-in-Charge.

Earth contineuty conductor or main earthing lead fixed to walls or to poles or any other indicated situation for loop earthing with 32mm x6mm earth strip complete all as specified and as directed by Engr-in-Charge.

Supply and fix Air termination, single pointed, copper rod 12mm dia and 300mm long complete all as specified and directed

Jaya Construction (BID ID -3420008)

ABC CONSTRUCTION CO. (BID ID -3419878)

K R KAUSHAL AND SONS (BID ID -3425801)

M/s Sultan Khan (BID ID -3419774)

awashyakta enterprises (BID ID -3427398)

Saket Traders (BID ID -3418672)

AIRDOT ENGINEERING (BID ID -3426540)

Shivam Enterprises (BID ID -3419292)