CA NO CWE PNH 18 2019 20

Amount

Total Amount of Sch 'A' Part - I (Building Work)

Total amount of Sch 'A' Part-II (Site Clearance and development Work)

Total Amount of Sch 'A' Part -III (Internal electrification Work )

Total Amount of Sch 'A' Part -IV (Protective work )

Total Amount of Sch 'A' Part -V (Area drainage )

Total Amount of Sch 'A' Part -VI (Perimetre Fence Work )

Total Amount of Sch 'A' Part -VII ( Path Work )

SCHEDULE 'A' PART- VIII (Misc item of work) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under col of "Pre Priced rate" signifies this fact only.

(INTERNAL ELECTRIFICATION WORK)

Lamp holder insulated body with back plate for batten fittings and including LED lamp 9 watts White non dimmable B-22 holder base with polycarbonate body complet all as directed. Make C&S Cat Part No LTHPLED LAMP 9W/B22 or equal in Bajaj/ Philips /Havells as approved.

LED light fitting, single tube, 1 x 20 w LED, T8, 230 V (power factor not less than 0.90), box type, CRCA body, bipin holders connector blocks, etc. Complete with all accessories internally pre-wired, including LED lamp T8 20 W with aluminium heat shrink and connecting up with PVC insulated and sheathed, 1100 volts grade, flexible, multistranded 1.0 sqmm copper conductor three core cable complete all as directed. Make: Cat part No. DIJB12LT8-20 for fittings and LTT8-20 watt or equivalent in Philips/Havells.

Street light fitting 25 watt LED, IP-65 protection, single peice pressure die cast aluminium housing high grade powder coated finish with heat resistant toughened clear glass cover for lamp and control gear compartment with high voltage surge protection device upto 5 KV, prewired including 1.60m long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of FI 40 x 6mm with bolts, nuts and washers and conductor to fitting with 3 core 1.5 sqmm PVC insulated cable complete all as specified and directed. Make: CG Cat part No LSTR-25-CDL or equivalent in Philips/Bajaj.

Distribution board, IP-43 in sheet metal enclosure duly flushed in wall, when MCB to be used with 200 Amps rated copper bus bar confirming to relavent IS SPN 6 way complete all as specified.

MCB single pole & neutral 5 to 32 amps 10 KA "C" series complete all as specified and directed.

MCB single pole 5 to 32, 10 KA "C" series complete all as specified and directed.

(Perimeter Fence) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under col of "Pre Priced rate" signifies this fact only.

Fence post made of galvanized steel tube, light grade outer dia 76 mm 3.25 mm(+/- 10%) thick length 1405mm (+/-5%) 1055mm above tie beam + 350mm under the 350mm embedded in RCC column weight not less than 5.84 Kg/RM (+/-10%)weight not less than 5.84 Kg RM (+/- 10%) complete all as directed.

Weld mesh panels produced by elect welded galvanized wires having dia 4.0mm (+/-0.05mm), Mesh size of 12.7x 76.2mm long mesh (mesh wire IS 280:2006), Panel size 266x955mm of 20.52 Kg, Zinc matelic coating 40 to 50 GSM powder coating and subsquently polyester powder coated, layer have a thickness of 60 to 80 microns, colour real 60005 powder coating should with stand 1000 hrs of salt spray tested (type tasted certificate to be provided) wire tensile strength. Min 550 N/Sq MM weld strength of the vertical wire and fixed with omega clamps complete all as shown on drawings and as directed. Note : Omega clamps shall be measured and paid for separately as, 'Supply Only' under respective item of schedules.

Supply only Omega clamps with profile cover cleat to tighten the mesh panel along the posts with chamber 78 mm 35 mm width and 3mm think flat-35mm width 3mm thick (MS strip as per IS 1730) (3 Nos per posts ). Each clamps will supplied with a pair of SS 304 mushroom headed square necked bolts and security nuts MBx50 (IS 8535-1987) complete all as directed.

Straining Y-Arm for supporting top punched tap concentrina coil MS angle of size 50x50x6mm having length 750mm of each arms and coating with hot dip galvanized of 350 GSM (Hot dip galvanized as per IS 2629/ IS 4759/ASTM A 123), outer dia 62 mm of skeeve cap, bolted on top the fence post straining posts installed all as shown on drawings and as directed.

Concertina coil 1050 mm dia/56 loops, 2.5 mm core wire, coil dia 1050 mm, type of strip heavy galvanised (IS 1730) type of core wire heavy galvanised (IS 280-2006) core wire dia 2.50 mm dia cinc coating to strip minimum 200 GSM/Sqm zinc coating on wire, minimum 275 GSM/Sqm (IS 6745-1972-2006) tensile strength of wire 1400-1500 N/Sqmm, Weight 14.63 Kg (+5%), number of loops 56 blade, length 22 mm, barb profile medium blade (MBBT) distance between barb 35 mm stretchable length 12 meters, type of clip hardened stealing galvanised steel complete all as directed.

Sub total of Schedule 'A' Part-VIII

M/S KIRAN CONSTRUCTIONS

SATVIR GUPTA ENGINEER and CONTRACTOR

GUPTA CONSTRUCTION

Kanwal Nain Behl

M/s V6 Infrastructures Pvt. Ltd.

M/s Kay Aar Enterprises

mohan lal gupta sons