ADDITION ALTERATION AND SPECIAL REPAIRS TO COMMUNITY HALL AT PH-I IN DRDO TOWNSHIP, PHASE-I, CV RAMAN NAGAR, BANGALORE

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking outside of MD land of area 3 sq. Metres and below, complete all as specified and directed.

Taking down aluminium door with frame n.exc 4 sq. m each complete all as specified and directed.

Taking down aluminium window with frame exc 1 sq. m and n.exc 2 Sqm each complete all as specified and directed.

Dismantling of composite steel windows / ventilators not exceeding 0.60 Sqm single leaf double shutter with fixed portion including taking down glass panes and mosquito proof mesh but except grill / guard bars in any position complete all as specified and directed (ONLY SHUTTER DISMANTLING).

Dismantling of composite steel windows / ventilators exceeding 0.60 Sqm but not exceeding 1.80 Sqm double / triple leaf double shutter with fixed portion including taking down glass panes and mosquito proof mesh but except grill / guard bars in any position complete all as specified and directed (ONLY SHUTTER DISMANTLING).

Providing & fixing for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately): For fixed portion.

Providing & fixing for powder coated aluminium (minimum thickness of powder coating 50 micron) shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately).

Providing & fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item): with float glass panes of 4.0 mm thickness (weight not less than 10Kg/Sqm).

Providing & fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item): with float glass panes of 5 mm thickness (weight not less than 12.50 Kg/Sqm).

Providing & fixing fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading for shutters for doors, windows and clerestory windows complete all as specified and directed.

Dismantling steel work manually / by mechanical means in built up sections without dismembering and stacking within 50 Metres lead as per direction of Engineer-in-Charge.

Providing & fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm and braced with flat iron diagonals 20 x 5 mm size, with top and bottom rail of T-iron 40 x 40 x 6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer complete all as specified and directed.

Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete all as specified and directed.

Providing & fixing factory made P.V.C. door frame of size 50 x 47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15 x 15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19 x 19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65 /100 mm size, complete as per manufacturer’s specification and direction of Engineer in-Charge.

Providing & fixing factory made panel PVC door shutter consisting of frame made out of MS tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15 x 15 mm for top & bottom rails. MS frame shall have a coat of steel primers of approved make and manufacture. MS frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the MS frame welded / sealed to the styles & rails with 7 mm (5 mm + 2 mm) thick x 15 mm wide PVC sheet beadingon inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-Charge, manufacturer's specification & drawing, 30 mm thick plain PVC door shutters.

Providing & fixing for Second class teak wood 35 mm thick shutters panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-Charge. Note: Butt hinges and necessary screws shall be paid separately.

Providing & fixing Ply wood 7 ply, 9 mm thick, Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR type for panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows complete all as specified and directed.

Providing & fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood complete all as specified and directed.

Providing & fixing 35 mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws complete all as specified and directed.

Providing & fixing pressed steel door frames Profile C (size 125 x 60mm x 40 mm) conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified, fixing with adjustable lugs with split end tail to each jamb and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

Providing & fixing pressed steel door frames Profile B (size 105 x 60mm x 40 mm) conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards,lock strike-plate and shock absorbers as specified, fixing with adjustable lugs with split end tail to each jamb and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

Providing & fixing 150 x 10 mm aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete all as specified and directed.

Providing & fixing 100 x 10 mm aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete all as specified and directed.

Providing & fixing 125 mm aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete all as specified and directed.

Providing & fixing 100mm aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete complete all as specified and directed.

Providing & fixing 300 x 16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete all as specified and directed.

Providing & fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. 100 x 58 x 1.90 mm complete all as specified and directed.

Providing & fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. 75x47x1.80 mm complete all as specified and directed.

Providing & fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete all as specified and directed.

Providing & fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 Kg to 80 Kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete all as specified and directed.

Providing & fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logoembossed on the body / plate with double spring mechanism and door weight upto 125 kg for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and With stainless steel cover plate minimum 1.25 mm thickness, with brass pivot and single piece M.S. sheet outer box with slide plate etc, complete as per the direction of Engineer-in-Charge.

Providing & fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete with single rubber stopper complete all as specified and directed.

Providing & fixing ISI marked oxidised M.S. single acting spring hinges 100mm long with necessary screws etc. complete all as specified and directed.

Providing & fixing bright / matt finished Stainless Steel handles 100mm long of approved quality & make with necessary screws etc complete all as specified and directed.

Providing & fixing magnetic catcher double strip (horizontal type) of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete all as specified and directed.

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete, overall width 50 mm complete all as specified and directed.

S&F, tubular curtain rail, Stainless steel SS grade 304, curtain rod 20 mm dia 1.20mm thick including taking down unserviceable rod / rail complete all as specified and directed.

S&F, Stainless steel SS grade 304, curtain decorative type brackets, 1.20mm thick suitable to hold the curtain rod with wooden round blocks suitable to curtain rod of 20mm dia, fixed with suitable steel screws and PVC cleats, including taking down unservicable brackets complete all as specified and directed.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 Metres lead) as per direction of Engineer?in-Chage.

Providing & fixing G.I. pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall 15 mm dia nominal bore complete all as specified and directed.

Providing & fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc, exposed on wall 20 mm dia nominal bore complete all as specified and directed.

S&F, (SWR) PVC pipes 110 mm dia single socketed in any length with rubber ring joints laid under floor or on walls fixed as soil waste / vent pipes including taking up or down existing PVC / CI pipes and connections complete all as specified and as directed.

S&F, (SWR) PVC pipes 75mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil waste / vent pipes including taking up or down existing PVC pipes and connections complete all as specified and directed.

S&F, PVC (SWR) bends any radius, 75mm bore with / without access door, complete all as specified and directed.

S&F, PVC (SWR) bends any radius, 110mm bore with / without access door, complete all as specified and directed.

S&F, PVC (SWR) floor trap with and including, plain / single hole chromium plated grating including jointing to waste pipe with solvent cement, 75mm dia, complete all as specified and directed.

S&F, PVC (SWR) multi-floor trap, plain with chromium plated grating including jointing with solvent cement, 75mm dia, including dismantling the damaged trap, complete all as specified and directed.

S&F, 75mm dia outlet PVC Nahani trap with grating as fixed in repairs complete all as specified and as directed.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge.

Dismantling of flushing cistern of all types (C.I. / PVC / Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 Metres lead complete all as specified and directed.

Providing & fixing W.C. pan with ISI marked white solid plastic seat and lid for white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete all as specified and directed.

Providing and fixing White Vitreous China Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests for water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete all as specified and directed.

Providing & fixing white vitreous china urinal of approx. size 610 x 390 x 370 mm including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-Charge.

S&F in repairs vitreous china snow white, wash hand basin counter sunk type of size 560 mm x 470 x 190mm including, CP Waste coupling of 32 mm, corrugated waste pipe, brackets & supply and grouting 6 to 8 mm dia GI racket bolt at the back side of WHB and making good existing surfaces complete all as specified and directed.

Providing & fixing Stainless Steel A ISI 304 (18/8) Kitchen sink with drain board of size 510x1040 mm bowl depth 250 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete all as specified and directed.

Providing & fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete, 32 mm dia, flexible pipe complete all as specified and directed.

Providing & fixing 15 mm nominal bore C.P. brass two way bib cock of Jaquar CON-041KN or equivalent of approved quality conforming to IS: 8931 complete all as specified and directed.

Providing & fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS: 8931 complete all as specified and directed.

Providing & fixing 15 mm nominal bore C.P. brass pillar cock of Jaquar CON-041KN or equivalent of approved quality conforming to IS: 8931 complete all as specified and directed.

Providing & fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 complete all as specified and directed.

Providing & fixing of 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS: 8931 complete all as specified and directed.

Providing & fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter complete all as specified and directed.

Providing & fixing uplasticised PVC connection pipe with brass unions 60 cm length and 15 mm nominal bore complete all as specified and directed.

S&F, Health faucet, brass body with 1mtr SS braided rubber hose pipe & wall hook complete all as specified and directed. Make: CERA or equivalent.

S&F in repairs Towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat etc complete all as specified and directed.

CP peg set (set of five) fancy type, complete all as specified and directed.

Stainless steel soap dish holder, fixed to wall with chromium plated brass screws and PVC cleat, complete all as specified and directed.

Providing & fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing rectangular shape 453 x 357mm complete all as specified and directed.

Providing & fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing rectangular shape 1500 x 450 mm complete all as specified and directed.

Providing & fixing PTMT 15 mm Urinal spreader size 95 x 69 x 100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms complete all as specified and directed.

Providing & fixing PTMT Waste Coupling for urinal, of approved quality and colour Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms complete all as specified and directed.

Disconnecting damaged overhead / terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-Charge.

S&F, rotational moulded polyethylene water storage tanks three layered (cylindrical, vertical with closed top) hoisted and fixed in position of 500 to 1000 litres capacity complete all as specified and directed.

Providing & fixing PTMT ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P. / H.P.H.D. plastic ball, 20 mm nominal bore, 120 mm long, weighing not less than 198 gms complete all as specified and directed.

Providing & fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore complete all as specified and directed.

Demolishing cement concrete manually / by mechanical means including disposal of materialremoving debris outside MD land as per direction of Engineer-in-Charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix).

Demolishing cement concrete manually / by mechanical means including disposal of material removing debris outside MD land as per direction of Engineer-in-Charge. Nominal concrete 1:4:8 or leaner mix (including equivalent design mix).

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level, 1:3:6 (1 Cement : 3 manufactured sand derived from Recycled Concrete aggregate (RCA) : 6 graded stone aggregate 40mm nominal size Recycled Aggregate (RA) as in paving / plinth protection laid in panels, finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling tile work in floors and walls laid in cement mortar for thickness of tiles 10 mm to 25 mm including stacking material within removing debris outside MD land complete all as specified and directed.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material removing debris outside MD land complete all as specified and directed.

Providing & fixing, first quality ceramic glazed wall tiles size 450 x 300 mm having suitable colour design (thickness to be specified by the manufacturer) of approved make in all colours of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3Kg per Sqm including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

Providing and laying anti-skid Ceramic floor tiles 300 x 300 mm or of suitable size (thickness to be specified by the manufacturer) of approved make in all colours and texture of any size as approved by Engineer-in-Charge, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete all as specified and directed.

Providing & laying vitrified floor tiles Size of Tile 600 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg/ Sqm including grouting the joints with white cement and matching pigments etc., complete all as specified and directed.

Providing & laying vitrified floor tiles size of tile 600 x 600 mm (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to I.S. 15622 of approved make in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 Kg/Sqm including grouting the joint with white cement & matching pigments etc. complete all as specified and directed.

Providing & fixing 18 mm thick Granite stone slab colour black, cherry / Ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), area of slab over 0.5Sqm joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels complete all as specified and directed.

Providing & laying Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick complete all as specified and directed.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete all as specified and directed.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering - for all work 1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete ggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA) aggregate as in foundation filling etc., complete all as specified and directed.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering - for all work 1:2:4 (1 cement : 2 coarse sand (Zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size Recycled Concrete Aggregate (RCA) upto 25%) complete all as specified and directed.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement complete all as specified and directed.

M&L for Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) complete all as specified and directed.

Supply only integral water proofing compound. Make: Fosroc / Dr Fixit / Asian.

Material and labour for roof treatment as follows:- (a) M&L for Chip out the existing loosed bitumen / bitumen membrane completely reach up mother slab, clean the surface throughly to make it smooth and free of any foreigh material, repairs the concrete wherever damaged using PMM HS repairo, repairing of construction joints / cracks by chasing with cutting machine and fill the same with polymerized mortar in HS repairo, coving of 75 x 75mm should be made at the junction of wall and raft slab using polymerized cement mortar 1:4 admixed with advanced latex plus. (b) Applying one coat of 50% diluted self priming PU roof coat. Allow to dry bond coat for 4-6 hours before applying PU coat and surface to be cleaned before applying PU coat.

(c) Applying two coats of single component, cold applied, water based polyurethane modified acrylic dispersion with highly elastic and UV resistant water proofing treatment to the roof with HS PU Roofkoat of Berger or equivalent at 0.6 kg/Sqm for each coat without dilution confirming to ASTM D 6083-97a (Standard Specification for Liquid Applied Acrylic Coating Used In Roofing) each coat should allow to dry 4-6 hours. The component shall have a density of 1.25 to 1.3kg/per Litre, having tensile strentgh of 1.5N/mm2, having elongation of 350% with solid content not less than 60% in 2 coats. SRI value should be more than 100. The quoted rate shall include surface prepartion, repair the crack in mother slab by chasing with cutting machine and fill the same with polymerized mortar in CM 1:4 admixed with latex agent of reputed manufacture, making coving at junction, bore packing, treatment of construction joints completely as per manufacurer's specification and direction of the Engineer-in-Charge. Make: Berger / Bostic / Fosroc / Sika / Asian. Note: The above treatment shall be got carried out by the authorised applicator of the manufacturer approved by the GE.

Demolishing brick in cement mortar manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material removing debris outside MD land as per direction of Engineer-in-Charge.

Providing & laying factory made Precast concrete solid blocks of 200 mm thickness of grade M-10 made of C&D waste from approved manufacturer in super structure above plinth level upto floor V level in cement mortar 1:6 (1 cement : 6 coarse sand) complete all as specified and directed.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 Metres lead complete all as specified and directed.

M&L for 12 mm cement plaster finished with a floating coat of neat cement of mix in cement mortar 1:6, on brick work / concrete surfaces complete all as specified and directed.

M&L for 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sand) complete all as specified and directed.

M&L for 6 mm cement plaster finished with a floating coat of neat cement of mix in : 1:3 (1 cement : 3 fine sand), on brick work / concrete surfaces complete all as specified and directed.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete all as specified and directed.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade for New work (two or more coats) over and including water thinnable priming coat with cement primer complete all as specified and directed.

Providing & applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

Distempering with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete as per manufacturer's specification one or more coats on old work complete all as specified and directed.

Wall painting with plastic emulsion paint one or more coats on old work of approved manufacturer and of required shade and colour complete as per manufacturer's specification.

Finishing New work (two or more coats applied @ 1.43 litre / 10 Sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm, on walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489: 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives complete all as specified and directed.

Finishing Old work (two or more coat applied @ 1.67 ltr/ 10 Sqm) on existing cement paint wall surface with Acrylic smooth exterior paint of required shade including over the cement based putty wherever is required complete all as specified and directed.

Finishing walls with textured exterior paint of required shade over the cement based putty etc on old work (two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm.) complete all as specified and directed. Note: The quoted rate included for cement based putty.

Painting one or more coats on old work with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade complete all as specified and directed.

Painting two or more coats on new work with synthetic enamel paint of approved brand and manufacture to give an even shade complete all as specified and directed.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) complete all as specified and directed.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking outside of MD land : Thickness above 10 mm up to 25 mm complete all as specified and directed.

Providing & fixing in position wall panelling at all heights with 15 mm thick fully perforated square / butt Edge Tiles with Painting) integral densified calcium silicate panels / tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.70 (minimum) as per IS-8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (Part-4), fire performance as per BS:476 (Part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per Sqm including both sides) to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels / tiles are to be screw fixed with self tapping panhead nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels.The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 Metre) roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials outside of MD land complete all as specified and directed.

Providing & fixing false ceiling at all heights with 15mm thick Tegular edged light weight calcium sliciate false ceiling tiles with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595x595mm of approved texture, design & patterns as per CPWD specification 2019 to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 33mm thick (galvanized @ 120 grams per Sqm including both sides) comprising of main-T runners of size 24x38mm of length 3000mm, cross-T of size 24x32mm of length 1200mm and secondary intermediate ross-T of size 24x32mm of length 600mm to formgrid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per Sqm) i.e. 12x50mm long dash fasteners, 6 dia fully threaded hanger rod upto 1000 mm length & L-shape level adjuster of size 76x25x25x1.6mm fixed with grid & Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 2x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40mm of length 3000mm to be fixed on periphey wall / partition with the help of plastic rawl lugs 450mm center to center and 40 mm long dry wall SS screws. The work shall be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge.

Providing & fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS-710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-Charge. (Payment of providing and fixing auto closing hinges shall be paid separately)

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 Metres lead of Asbestos Cement sheet complete all as specified and directed.

Providing & fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) 0.50 mm (+ 0.05%) total coated thickness with zinc coating 120 grams per Sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 Metre or as desired by Engineer-in-Charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete all as specified and directed.

Providing & fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, Zinc coating 120 grams per Sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws complete for Ridges plain (500 - 600mm) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Providing & fixing on wall or floor face unplasticised rigid PVC rain water pipes conforming to IS: 13592 type 'A', including jointing with sealring conforming to IS: 5382, leaving 10 mm gap for thermal expansion for single socketed pipes 110 mm diameter all as specified and directed.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Demolishing RCC work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material removing debris outside MD land as per direction of Engineer-in-Charge.

Providing & placing in position precast reinforced cement concrete waffle units, square or rectangular, as per design and shape for floors and roofs in 1:1½:3 (1 Cement : 1½ coarse sand (Zone-III) derived from RCA : 3 graded stone aggregate 10 mm nominal size derived from RCA), including flush or deep ruled pointing at joints in Cement mortar 1:2 (1 Cement : 2 Fine sand), form work in precasting, handling, hoisting, centering and erection complete for all floor levels but excluding the cost of reinforcement for slabs and similar complete all as specified and directed.

Thermo-Mechanically Treated bars of grade Fe-500 D or more steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level complete all as specified and directed.

Providing & fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-Charge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). complete all as specified and directed.

Taking down / removing vegetation growth / plants of any size of area n.exc 0.5sqm above chajjas, roof slabs, parapet walls, junction of SWR pipe and wall etc upto roots and applying / injecting chemical and making good the surface in CM 1:3 upto height of 16 m all as specified and directed.

Two or more coats on new works including a coat of wood filler French spirit polishing complete all as specified and directed.

Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m for all kinds of soil complete all as specified and directed.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge for all kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m for all kinds of soil complete all as specified and directed.

Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level : 1:4:8 (1 Cement : 4 coarse sand (Zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete all as specified and directed.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level 1:3:6 (1 Cement : 3 coarse sand (Zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) complete all as specified and directed.

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete all as specified and directed.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement complete all as specified and directed.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes complete all as specified and directed.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work complete all as specified and directed.

Providing & fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) 0.50 mm (+ 0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-Charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete all as specified and directed.

Providing & fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws complete for ridges plain (500 - 600mm) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F, UPVC Pipes (SCH-40),100mm dia as rain water pipes and gutters complete all as specified and directed.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m complete all as specified and directed.

S&F, Heavy duty Vitrified tiles light colour, 10mm thick (square / rectangular) polished, area of each tiles exc 0.18Sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed of CM 1:4 complete all as specified and directed.

S&F, Heavy duty Vitrified tiles light colour, 10mm thick (square / rectangular) polished, area of each tiles exc 0.18 Sqm but not exceeding 0.36 sqm, in skirting and dado including 10mm CM 1:3 rendering etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Providing & laying Polished Granite stone flooring with Polished Granite stone slab colour of Black, Cherry / Ruby Red or equivalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and directed by the Engineer-in-Charge.

Providing & laying 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade complete all as specified and directed.

Taking down carefully old unserviceable aluminium / copper point wiring (light, fan, socket or power) complete with fittings such as switches, sockets, ceiling rose, light fittings etc and making good the distrubed surfaces to match with existing surfaces complete all as specified and directed.

M&L for Point wiring with single core copper conductor cable of size 1.5 Sq mm, PVC insulated, unsheathed, multistranded FRLS type, 1100V grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit 25 mm dia medium grade with conduit acessories concealed in walls / floors / except RCC ceilings / beams etc duly cutting chases / grooves and making good the distrubed surfaces to match with existing surfaces including modular switches of 1 way or 2 way as required with GI modular flush boxes, modular white plate with frame of suitable sizes for mounting of modular switches, sockets and regulators etc and including 1.5 Sqmm PVC insulated, unsheathed, copper conductor cable, FRLS type, 1100V grade green in colour as earth continuity conductor connecting to earth dolly for one light point / ceiling fan point / exhaust fan point controlled by one, 1 way modular switch.

All as per Sl item No. 149 above, but for one 3 pin 6 Amps socket outlet point controlled by one modular switch on the same board with other switches. Note: Modular sockets to be measured and paid separately.

All as per Sl item No. 150 above, but for twin control light point controlled by two, 2 way modular switches including 2 way modular switches.

M&L for circuit / submain wiring with 2 run of 1.5 sq mm of single core copper conductor cable PVC insulated, unsheathed, multistranded FRLS type, 1100V grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit not less than 25 mm dia medium grade with conduit acessories concealed in walls / floors / ceiling etc duly cutting chases / grooves and making good the distrubed surfaces to match with existing surfaces including 1 run of 1.5 Sq mm single core copper conductor cable, PVC insulated, unsheathed, multistranded FRLS type, 1100V grade green in colour as earth continuity conductor and connecting to earth dolly complete all as specified and directed for ceiling lights / flood lights / security lights / socket outlet 3 pin 6 Amps on independent board. Note: 3 runs of 1.5 Sq.mm and 1 run of PVC conduit will be measured and paid as one unit.

All as per Sl item No. 152 above, but using 2 runs of 2.5 sqmm copper conductor cable, PVC insulated, unsheathed, multistranded FRLS type cable, 1100 volts grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit not less than 25 mm dia medium grade with conduit acessories concealed in walls / floors / ceiling etc duly cutting chases / grooves and making good the distrubed surfaces to match with existing surfaces including 1 run of 2.5 Sq mm single core copper conductor cable, PVC insulated, unsheathed, multistranded FRLS type, 1100V grade green in colour as earth continuity conductor and connecting to earth dolly complete all as specified and directed for socket outlet 6 pin, 16 Amps on Independent board. Note: 3 runs of 2.5 Sq.mm and 1 run of PVC conduit will be measured and paid as one unit.

S&F, modular type socket out let, 3 pin, 6 Amps, 2 module, 240 volts complete all as specified and directed.

S&F, GI modular box with modular plate and cover in front of suitable size in recess including providing and fixing 6 pin 5/6 A modular socket outlet 2 in 1 type and 5/6 A modular switch and connections as required complete all as specified and directed.

S&F, GI modular box with modular plate and cover in front of suitable size in recess including providing and fixing 6 pin 5/6 &15/16 A modular socket outlet 2 in 1 type and 15/16 A modular switch and connections as required complete all as specified and directed.

S&F, modular electronic fan regulator 120 W, 230 V, 2 module complete all as specified and directed.

S&F, ceiling rose surface bakelite three terminal, 230 V complete all as specified and directed.

S&F, VTPN MCCB DB 8 way, 415V, 50Hz, AC, sheet metal enclosure, double door, IP 43 protection suitable for MCCB 4 pole upto capacity 100 Amps as incomer and SP/TP MCB's as outgoings comprising of 200 Amps bus bar rating, neutral bar, duly powder coated painting and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, MCCB 100 A, 4 pole,16 KA, 415 V, AC including taking down existing unserviceable item complete all as specified and directed.

S&F, MCB DB SPN 08 way, 240V, 50Hz sheet metal enclosure double door type IP-43 protection, factory made powder coated painting and tinned copper bus bar neutral link and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, MCB DB SPN 04 way, 240V, 50Hz sheet metal enclosure double door type IP-43 protection, factory made powder coated painting and tinned copper bus bar neutral link and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, MCB SP 6 to 32 Amps, 10 KA 'C' curve, 240 volts, 50 Hz, AC and taking down existing unserviceable items complete all as specified and directed.

S&F, MCB SPN 40 Amps, 240 volts 50 Hz AC,10 KA 'C' series taking down existing unserviceable items complete all as specified and directed.

M&L for submain wiring with 2 runs of 10 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 10 Sqmm green PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item complete all as specified and directed. Note: 3 runs of 10 Sq.mm and 1 run of PVC conduit will be measured and paid as one unit.

M&L for submain wiring with 2 runs of 06 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 06 Sqmm green PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item complete all as specified and directed. Note: 3 runs of 6 Sq.mm and 1 run of PVC conduit will be measured and paid as one unit.

M&L for submain wiring with 2 runs of 04 Sqmm, single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls, floors except in roofs duly chases cutting groove by chiselling / mechanically as required and making good the disturbed surfaces to match with existing surface including 1 run of 04 Sqmm green PVC insulated, single core, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade as earth continuity conductor and connecting to common earth dolly including taking down old item complete all as specified and directed. Note: 3 runs of 4 Sq.mm and 1 run of PVC conduit will be measured and paid as one unit.

S&F, MCB DB SPN 02 way, with MCB DP 32 Amps 'C' curve, 10KA, 240V, 50Hz enclosed in sheet metal enclosure double door type IP-43 protection, factory made powder coated painting and tinned copper bus bar neutral link and fixed flush in wall and making good the disturbed surfaces to match with existing surface and making electrical connections using suitable sizes of copper thimbles / lugs including taking down old unserviceable item complete all as specified and directed.

S&F, BLDC type ceiling fan 1200 mm sweep, air delivery 210 cfm complete with blades, down rod and other accessories, BEE five star rated with brushless direct current motor and making connections by providing copper cable including taking down existing ceiling fan and deposited in MES store yard complete all as specified and directed.

S&F, LED light fitting 36 Watts ultra modern recessed mounting luminare 2 feet x 2 feet size, glare free uniform illumination with longer life and less maintenance approved model complete with 3 core sheathed copper flexible wire of suitable size upto light fitting and PVC connector including taking down old unserviceable item complete all as specified and directed.

S&F, LED light fitting 36 Watts ultra modern surface mounting luminare 2 feet x 2 feet size, glare free uniform illumination with longer life and less maintenance approved model complete with 3 core sheathed copper flexible wire of suitable size upto light fitting and PVC connector including taking down old unserviceable item complete all as specified and directed.

S&F, LED light fitting 20 Watts, 4 feet suitable for surface / wall mounted fitting batten with powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired up to terminal block, power consumption <20W, luminaire lumen >2000 lm, system efficiency of >100 lumens/W, as per IEC-624718 & electrical insulation class 1, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficiency >85%, power factor > 0.9, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV including taking down old unserviceable item complete all as specified and directed.

S&F, LED light fitting 10 Watts, 2 feet suitable for surface / wall mounted fitting batten with powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired up to terminal block, power consumption <10W, luminaire lumen >1000 lm, system efficiency of >100 lumens/W, as per IEC-624718 & electrical insulation class 1, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficiency >85%, power factor > 0.9, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV including taking down old unserviceable item complete all as specified and directed.

S&F, LED security light fitting 36 Watts made up of die cast housing with toughend glass and high power LEDs complete with IP 66 protection duly pre-wired and fixing arrangement on wall surface at suitable height by providing GI bracket medium grade of suitble size and adequate length with necessary fixing clamps and making electric connections by providing 3 core copper conductor cable from ceiling rose to light fitting including taking down old unserviceable item complete all as specified and directed.

Taking down existing exhaust fan of any type for carrying out repairs by replacing spare parts and components as required and rewinding including servicing / greasing, painting and repalcing the louvers and SS wire mesh at any height including making hole to wall and making good the disturbed surfaces and writing MES No & refixing the same after above repair and making connections by providing copper cable complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried in ground vertically to a depth not less than 2.25 metres below normal ground level with top edge of earth plate not less than 1.5 metres below normal ground level including GI strip 25 x 5mm connected galvanised iron earth plate by means of GI bolts, nuts, check nuts and washers connected to earth test point all as specified or indicated including testing on completion with and including 40mm bore light grade GI protection pipe 7.5 metres long including PCC 1:2:4 pit with pre-cast RCC 1:2:4 type B1 cover 40 mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hook made out of 6mm dia MS bars watering arrangement pipe of 20mm dia medium grade with wire mesh funnel andproviding common salt and charcoal filling all around earth plate upto 15cm thick and necessary excavation and earth work in any type of soil and returning filling of soil, removing surplus soil etc complete all as specified and directed.

S&F, GI Strip 25 x 5mm drawn on surface or in recess for connections etc duly welded at joint potions as required at site complete all as specified and directed.

Taking down the existing electronic energy meter of any type servicing and repalacing the spare parts and components and testing the same including providing 3mm thick hylum sheet mounting plate of suitable size and shall be provided inside the meter box as per the site requirement including drilling holes of suitable size, fixed with screws, wooden guttas etc including connecting and testing by switching on prevailing load for atteast 4 Hrs and recording the reading on hourly basis and including making locking arrangements complete all as specified and directed.

S&F, On-Load change over switch 200 A, 4 pole, 415V, 50 Hz, AC in sheet metal enclosure and necessary fixing arrangement and making connections by providing lugs including taking down the old material complete all as specified and directed.

S&F, LED flood light fitting 150Watts highly efficient LED's made of pressure die cast aluminium housing and suitable lens and toughened glass IP 66 protection with best in class design and robust heat sink and surge protections for long lasting performance and necessary fixing arrangement and making connections by providing copper cable etc complete all as specified and directed.

Supply, laying, testing & commissioning LT cable of size 3.5 core; 25 sq mm XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor cable 1100 volts grade laid in trenches, on wall, roofs, ceiling and drawn through pipes and making connections by providing lugs, gland etc complete all as specified and directed.

Supply, laying, testing & commissioning LT cable of size 2 core; 10 sq mm XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor cable 1100 volts grade laid in trenches, on wall, roofs, ceiling and drawn through pipes and making connections by providing lugs, gland etc complete all as specified and directed.

S&F, decorative hot dipped mild steel pole 6 mtrs length with grey powder coated finish including excavation / earth work and necessary fixing arrangement on PCC foundation 1:3:6 type C1 and making connections by providing copper cable from junction box complete all as specified and directed.

S&F, LED Post top lantern 15Watts with diecast aluminium, spigo, spun aluminium powder coated, opel PC diffuser and clear acrylicwith IP 65 protection and making connections by providing 3 core copper conductor cable complete all as specified and directed.

S&F, Junction box made of high quality DK thermoplastic of size 200 x 160 x 98 mm including four number connection terminals suitable mouted on DN rail for cable connections including MCB SP 6A, 10 KA 'B' curve, 230 V complete with thermoplastic cable glands and fixed on GI pipe and using pole clamps made out of appropriate material all as required at site or directed.

Excavating in trenches in any strata n exc 1.5 m wide and in depth for laying of cables and getting out complete all as specified and directed.

Removing of excavated material to a distance n exc 50 mtrs and deposting where directed at a level n exc 1.5 mtrs above the starting point complete all as specified and directed.

Returing, filling in, including spreading, levelling, watering and well ramming in layers n exc 25 cm thick complete all as specified and directed.

S&F, unreinforced precast concrete cable covers, class LV, type 1, flat size 250mm x 150mm x 40mm complete all as specified and directed.

M&L for screening of excavated earth (passing through 12 mm square mesh), laying riddled earth in trenches for cable protection below and above LT cables of 23 cm depth all as specified in SSR Part-I and complete all as specified and directed. Note: Punned thickness of riddled earth of 18 cm will be measured and paid.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate for coping of poles / plinth blocks of LT poles or any type of foundation or as required at site including fair finishing the exposed surfaces even and smooth without using extra cement including necessary form work complete all as specified and directed.

B5BUILDING SOLUTIONS

INDGUARD ENGINEERS

M/s M Munivenkatappa and Company

K. VENKATESH NAIDU

Phoenix Infra

D NAGI REDDY