Comprehensive repair of B/R services for MH area OTM accn and other area to kanjoli lines Bharatpur

Amount

Dismantling/demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc, complete all as specified and directed.

M & L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6.0 metre mean radius as wall built in cement & sand mortar 1:6, complete all as specified and directed.

Taking down cement or cement lime plaster of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of concrete surfaces as in ceiling including finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces in cement and sand mortar 1:4 on brick work or cement concrete surfaces including finishing the surface even and smooth, complete all as specified and directed.

M&L for preparation of newly plastered or un plastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted (copolymer based resin glue to be added for longer durability and better finish) over one coat of water based white pigmented alkali resistant priming paint, over 1 mm thick wall care putty on Wall Surface including all necessary arrangement for execution of work ,complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered or un plastered surfaces of wall including cornices, pilasters etc and applying two coat of cement based paint of approved colour on wall Surface including all necessary arrangement for execution of work, complete all as specified and directed.

Demolition of cement concrete (unreinfored) in ground floors and pavings nexc 15 cm thickness (below or above ground levels) complete all as specified and directed.

M&L for 75 mm PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and as directed.

M&L for 40 mm thick 1:2:4 type B-1 (using 20 mm graded stone aggrgate) finished even and smooth with using extra cement complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/path laid in panel surface finished even and fair without using extra cement complete all as specified and as directed.

Dismantling of floor hearth and wall tilling incl mortar beding removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate as in sub floor, laid and finishing the surface of concrete topping even and rough to receving of screed for tiling, complete all as specified and directed.

M&L for non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface of size 450x300x7 mm thick, laid over 15 mm thick rendering in cement mortar (1:3) and set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles, complete all as specified and directed.

M&L for 20-25 mm thick kota stone slab as in flooring/steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 15 mm thick machine cut kota stone slab on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in colored cement to match the shade of Kota stone laid over 10 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finishing rough to receive stone, complete all as specified and directed.

M&L for 18 - 20 mm thick black machine cut granite slab (of any type) (table rubbed and polished), as in steps, jambs, pillars, window- cills, cooking platform set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab laid over and including 15 mm thick cement screed in cement and sand mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 12 -15 mm thick granite work (of any type) (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 10 mm thick screed bedding layer in CM 1:3 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situation including making of hole suitable for gas pipe etc. complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps, seismic and othe similar bands, plinth courses, bed plates, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and directed.

M&L for sand stone slabs of 50 mm thick in sun-shades cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all as specified and directed.

Roughening surfaces of old concrete floor/Chajja/facia /roof surface, any type concrete projections by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M & L for brushing neat cement slurry with 3.0 kg of cement per sq. m complete all as specified and directed.

M & L for granolithic concrete 1:1:2 concrete surface topping 40 mm thick; laid over cement concrete etc. and finished to an even and fair surface complete all as specified and directed.

Dismantling wall and ceiling boards ( fibre, pulp, insulation ,etc. ) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

S&F anodised aluminium snap grid frame work of grid size 605 x 605 mm for false ceiling complete all as specified and directed.

S&F for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F for 4 mm thick non-asbestos fibre cement building boards fixed to aluminium framework, complete all as specified and directed. Note: Frame work for ceiling shall be measured and paid separately)

S&F for PVC wall panelling in repair with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angle fixed with solvent cement complete all as per manufacturer's instructions complete all as specified and directed.

Dismantling asbestos cement/galvalume/fibre glass (corrugated or semi corrugated) sheets in roof coverings, complete all as specified and directed.

Pre painted galvalume alumimnium zinc coating GI based corrugated steel sheet 0.50 mm thick, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified and directed.

Pre painted galvalume alumimnium zinc coating GI based plain steel sheet 0.50 mm thick sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Dismantling of posts or struts (wood, steel or RCC) embedded in concrete/brick work of any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section from unframed work, complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for cement concrete type B-2. 1:2:4 (using 40 mm graded aggregate) in foundations, filling and mass concrete, complete all as specified and directed.

S&F rolled mild steel work as Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates. conforming to Fe-410W Gde E-250 quality 'A', complete all as specified and directed.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165, complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W Gde E-250 quality 'A', complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc including cleaning for re-fixing or removal to store complete all as specified and directed

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc including cleaning for re-fixing or removal to store complete all as specified and directed

S&F GI tubing medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified and directed

S&F GI tubing medium grade galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified and as directed .

S&F in repair Bib tap, cast copper alloy long body with crutch or butterfly handle, screwed down, suitable for 15 mm nominal bore iron pipe screwed for iron or brass ferrule and fixed complete all as specified and directed.

S&F in repair pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shank and fly nuts, with or without lettered "Hot" or "Cold" for 15 mm nominal bore , screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm bore stop valves, cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm bore stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair Waste coupling of PTMT (half or full threaded) of 40 mm bore of discarge pipe . (Minimum weight 40mm- 60gms complete all as specified and directed.

S&F in repair vitreous china wash down water closet (Pedestal pattern) white excluding (flushing cistern and flush pipe), complete all as specified and directed.

S&F in repair vitreous china squatting pan,Órissa pattern size 580 x 440 mm white, with integral foot rest and CI 'P' trap complete , all as specified and directed.

S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device seat and cover for pedestal pan, complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, 10 lit capacity with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair of Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe including waste pipe complete all as specified and directed.

S&F in repair Vitreous China wash hand basin, white, flat back, size 550x400mm including brackets & waste pipe of PVC 32 mm bore of low or high densitycomplete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm including complete all as specified and as directed.

S & F in repair of chromium plated shower rose 125 mm dia with 200 mm long CP arm with swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed.

S&F in repair of Tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S & F in repair, 500 ltr ISI marked three layer, white colour, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with thread type cover and fixed with screw hoisted and fixed in position & including 20 mm brass ball valve complete all as specified and as directed.

S & F in repair, 1000 ltr ISI marked three layer, white colour, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with thread type cover and fixed with screw hoisted and fixed in position & including 20 mm brass ball valve complete all as specified and as directed.

Disconnecting existing tanks of capacity exc 500 litres & n exc 1000 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position after cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc. inculding refixing of float valve, gate valve, nipple socket all necessary fixures, making functional without overflow complete all as specified and as directed. Note: (i). Cleaning of tank shall be measured separately. (ii). If float valve is required to be replaced, the same shall be measured separately.

Disconnecting existing tanks of capacity exc 250 litres & n exc 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hositing if required reconnecting and re-fixing in position after cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc. inculding refixing of float valve, gate valve, nipple socket all necessary fixures, making functional without overflow complete all as specified and as directed. Note: (i). Cleaning of tank shall be measured separately. (ii). If float valve is required to be replaced, the same shall be measured separately.

Supply only PTMT ball valve of 20 mm bore high pressure of PTMT with epoxy coated aluminium rod & high denisty plastic ball screwed for iron pipe (minimum wt -210 grams) complete all as specified and directed.

S&F in repair PTMT ball valve of 15 mm bore high pressure of PTMT with epoxy coated aluminium rod & high denisty plastic ball screwed for iron pipe (minimum wt 142 grams for ball only) complete all as specified and directed.

S&F in repair PVC cover thread type for PVC Water tank 500 ltr capacity and fixed with screw to tank complete all as specified and directed.

M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

S&F welded steel wire fabric ,weight n. exc 4.00 kg/sq. m fixed to steel members complete all as specified and directed.

Demolition cement Concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate with smooth finish including necessary form work etc.complete all as specified and as directed.

Taking down chowkats or frames n. exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutter of any description area n exc 1 sq. m each complete all as specified and directed.

Taking down shutter of any description area exc 1 sq. m and n. exc 2 sq. m each complete all as specified and directed.

Taking down shutter of any description area exc 2.0 sq. m but n.exc 4 sqm each complete all as specified and directed.

S&F 30 mm thick Flush Shutters, Solid core construction, Single or double leaved rebating shall be square or splayed, with block board core and both face is covered with plywood face panels commercial type free from twist or wrap in plane, complete all as specified and directed

S&F factory made, 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc.diveded in squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in clause 8.24(a) SSR Part I complete all as specified and directed.

S & F Solid PVC Door Frame of the size 50 x 47 mm made out of 5 mm PVC sheet. The door profiles are to be reinforced with 19x19mm M.S Square tube. The profile shall be cut and mitred at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified & shown on SSR 2020 (Part-II) complete all as specified and directed.

S & F Mild Steel framed work as in doors or gates of angle or other section, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging with and including either hooks and hinges or steel hanging door fittings, also fastening and fixing of Fe 290(Gde-E-165) complete all as specified and directed.

S&F 1.00 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets or welded and fixed to steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning upmitred angles etc as required complete all as specified and directed.

S&F MS butt hinges heavy weight cold rolled of size 125 mm, complete all as specified and directed.

S&F MS butt hinges medium weight cold rolled of size 100 mm, complete all as specified and directed.

S&F SS hinges medium weight size 100 mm, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section, 125 mm length of bolt and fixed with screws, complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete as as specified and directed.

S&F Aluminium handles, cast type, anodised of 125 mm size complete all as specified and directed.

M&L for Painting to new or prevously untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified and directed.

M&L for Painting to new or prevously untreated steel surfaces of any description n exc10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or prevously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or from metal frame or stone or concrete or bricks surrounds glazed with putty, taking out old pins punching or drilling out, complete all as specified and directed.

S & F Sheet glass 4.0 mm thick, ordinary quality & glazing with oil putty in squares n.exc 0.5 sqm in each pane including punching or drilling out old glazing pins/spring clips, and providing & fixing new ones complete all as specified and directed.

S&F 4.8 mm thick sheet glass odinary quality and glazing with neoprene beading, complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples or rivets, complete all as specified and directed.

All as per srl Item No. 98 here in above, but fixed in repair, complete all as specified and as directed

Repairing of existing aluminium door single leaf exc 1.00 sq.m but nexc 2.0 sq. m including oiling and greasing of floor springs and making the door and shutter serviceable complete all as specified and directed. Note: Floor door springs where renewed shall be measured and paid separately under appropriate items.

Repairing of existing aluminium door single leaf exc 1.00 sq.m but n exc 2.0 sq. m including taking down all members, sheet glass of any thickness, aluminium cleat, neoprene rubber beading and resecuring all sections & tightening all joints including fixing new small cleats etc each n exc 100 mm and refixing all members, sheet glass, aluminum cleat, neosprene rubber beading and making the door and shutter serviceable, complete all as specified and directed. Note: Floor door spring, Neoprene rubber beading , Hinges, Door Closer where renewed shall be measured and paid under appropriate items.

Repairing of existing aluminium frame n exc 1.50 sq. m including taking down & resecuring all member of frame of any shape & size with aluminium cleat or straight pieces n exc 75 mm each , resecuring complete frame to opening with required size of PVC plug and screw not less than 100 mm complete all as specified and directed.

AlI as above Item No.119 but exc 1.50 sq. m and n exc 4.0 sq.m each complete all as specified and directed.

Supply only neoprene rubber beading suitable for aluminium door / window panels, complete all as specified and directed.

Supply only aluminium alloy hinges 100 mm size, complete all as specified and directed.

Supply only 150 mm size aluminium alloy handle, complete all as specified and directed.

S&F in repair for aluminium door seal of overall size 42 mm having nylon brush of 20 mm fixed on aluminium body strip of 22 mm, fixed with screw on Aluminium door, wooden shutters or PVC shutters, complete all as specified and directed.

S&F in repair Double action floor spring hydraulically regu-lated made up of mini-mum 1.25 mm thick alu-minium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repairs Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 3 , universal type , suitable for door shutters 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repair for 100 mm size mild steel 4 lever mortice lock vertical type, complete all as specified and directed.

S & F in repair for 150 mm floor door stopper of aluminium alloy body and tonge, anodised with hard drawn steel spring, complete all as specified and as directed

M & L for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including aluminium channels for sliding shutters, jointing cleats for fixing etc., complete all as specified and directed.

S&F Anodised aluminium window/ ventilator shutters side hung type with sash, aluminium section weight not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stay 150 mm long (1 No) suitable , type B-21 hinge 100 mm long (2 No), suitable handle (1 No) etc for each leaf, complete all as specified and directed.

S&F Anodised aluminium door shutters with aluminium section weight not less than 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, 02 Nos aluminium handle each door, hinges, anodised aluminium snap beading screws etc., complete all as specified and directed.

S&F aluminium deco grill in door and windows with weight not exceeding 1.00 Kg/Sqm including necessary arrangement for fixing etc as specified and directed.

S&F 4.80 mm thick sheet glass with solar control film 25 micron reflective type sticked to glass pane ,ordinary quality exc 0.5 Sqm in each pane complete all as specified and directed

S&F Door closer hydraulically regulated designation No 3, univeral type, of aluminium (extruded section body), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

S&F Door closer hydraulically regulated designation No 2, univeral type, of aluminium (extruded section body), suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as specified and directed.

S&F Aluminium Door seal of overal size 42 mm having nylon brush of 20 mm fixed on aluminium body strip of 22 mm, fixed with screw on Aluminium door, wooden shutters or PVC shutters complete all as specified and directed.

S&F 100 mm mild steel 4 lever mortice lock vertical type of size complete all as specified and directed.

Cutting or uprooting grass incl removing old mud phuska/ roof treatment of any thickness and description, removing rubbish off the premises, cleaning surface and preparing to receive new treatment complete all as specified and directed.

M&L for 20 mm thick screed bed or bedding layer of cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing surfaces for roof treatment by removing all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surfaces mechanically or by grinding to make it smooth before application, repair all cracks by cutting "V" groove and fill with PMC mortar (Polymer modified cement mortar) prepared by cleaning free from dust and loose particles and apply on dry surface first coat of crack fillar using putty knife or trowel allow to dry for 4 to 6 hr, afterthat apply second coat and dry for 4-6 hrs in ratio as per manufacturers specification, provide 75 mm x 75 mm coping made out of PMC mortar as above on all joints of vertical upstands to ensure that moisture content in the prepared surface does not exceed 5% immediately before application of liquid membrane. Material incorporation & Protection be provided as Terrasheild first apply with water (ratio terrasheild : water will be 4:1) as primer with coverage area 0.1 Kg per Sqm. After 2-3 hour later, second step apply directly first coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller.Spread non woven geo textile of 40 / 50 gsm with overlap of 50 mm in both direction when the surface is still tacky. After 4-6 hour later, apply third step apply directly second coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm with roller. final thickness of complete treatment should be minimum 1.0 mm. Water tank and Khurra location one additional coat of terrasheild 0.30 to 0.40 mm thickness coverage area 0.5 to 0.75 Kg per Sqm be provided. after complete application full curing minimum 7 days . Above complete application will be done by authorized apllicator from Manufacturer and manufacturer's specification. Make : IWL Co/ STP/Fosroc .

GANGA CONSTRUCTION

M/S MAMTA CONSTRUCTIONS

abhinav and company

VASUNDHARA AND COMPANY

M/s Ranaji Construction Co

M/S CHAUDHARY CONSTRUCTION

RAJESH ENTERPRISES

PD GUPTA AND COMPANY