SPECIAL REPAIR TO OTHER RANK MD ACCN BLDG NO. P - 90 AT ADM AREA, CPE ITARSI

Amount

Demolition of Cement concrete (unrein forced) in ground floor and pavings not exc 15 cm thickness (below or above ground level) including surface finishes of any type ie tiles, kota stone including removal of debris to a distance not exceeding 100m as directed by Engineer-in-Charge.

Excavating over areas, under floor n exc 1.5m deep and getting out any type of soil below floor complete all as specified.

Material and labour for 75 mm thick cement concrete type D2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as spciified and directed.

Material and labour for 75mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in pavement/plinth protection and joints shall be filled with bitumastic gola with 80/25 bitumen (1 part bitumen and 3 parts sand), finished the surface fair and even complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base floor to receive any type of glazed ceremic tiles complete all as specified.

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L for Moorum and sand filling under floors or pavings laid in layers n exc 15 cm thick spread, levelled and rammed including watering (Sand and moorun will be mixed in ratio 1:1 in filled under floor) complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level not exc 1.5m above the starting point all as specified and directed.

Taking down cement or cement lime plaster on brick walls etc including raking out joints, hacking for key scrubing down with water etc all as specified and directed.

M&L for 15 mm thick cement plaster as in cement mortar 1:6 on brick or concrete surface other than fair finish including dubbing coat if required & finishing with surface even and fair complete all as specified and directed (No extra payement will be paid for dubing coat).

M&L for 15 mm thick cement plaster externally as in cement mortar 1:4 and mixed with WPC as per manufacturer instructions with cement ) and finished fair and even complete. (Note :- WPC shall be measured & paid separately) including dubbing coat if required on ground directed by Engr in charge. (No extra payement will be paid for dubing coat).

M&L for 10 mm thick cement plaster in CM 1:3 on celing of concrete surfaces and finished the surface even and smooth complete.

Supply only water proofing compound of approved make.

M&L for cutting "V" section to cracks in existing roof or terracing/brick wall including cleaning, and grouting with cement sand slurry 1:3 complete all as specified.

Cutting chases pining in brick,concrete walls built in cement mortar or cement lime mortar making good to facings where required and pointing in cement mortor 1:3 to ends or edges of shelves lintels etc and cutting chases for concealed water tubing cutting exc 10 cm but not exc 20 cm girth all as spcefied and directed.

Material and labour for complete removal of existing treatment on plastered surfaces of walls including washing, rubbing down and stopping of old treatement plaster surface and applying two coats of anti fungal exterior emulsion paint over a coat of cement primer complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of anti fungal exterior emulsion paint over a coat of cement primer complete all as specified and as directed.

Material and labour for applying two coats of oil bound distemper over and including a coat of cement primer wall to new plaster surface complete all as specified and as directed.

Material and labour for complete removal of existing treatment of wall including, washing, rubbing down and stopping and applying two coat oil bound distemper over and including a coat of cement base wall care putty applied as per manufaturers instruction complete all as specified and directed.

M&L for applying 3 coat of white wash including preparation of new plaster surface on ceiling all as specified and directed.

M&L prepration of old decorated plastered or un plastered surface including cornices etc and applying one coat of white wash on ceiling all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc 1.5 Sgm each and making good of disturbed surface match the existing surface all as spcefied and directed.

All as per item No. 22 here-in-before but exc 1.5 Sgm but not exc 4 Sqm each.

S&F 125x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates,hinges,hold fast(40x3mm) etc including one shop coat of primer complete size /profile of frame as per IS all as specified and directed.

S&F 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast (40x3mm) etc including one shop coat of primer complete size /profile of frame as per IS all as specified and directed.

M&L pressed steel frames for cup board chowkhats of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc and one coat of redoxide primer complete all as specified and directed.

Material and labour for PCC 1:3:6 type C0 (using 12.5 mm graded stone aggregate) as in back filling of pressed steel frame etc complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in bed blocks for hold fast and as in roof kerb benching & similar work etc complete all as specified and directed.

S & F factory made 30 mm thick flush shutters solid core construction with block board core and plywood face panels complete all as specified and directed.

S&F 35 mm thick 2nd Class hard wood glazed and skeleton shutters , open rebeted and prepared to receive glass, gauze etc (without sash bars ), edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc , sizes of members of shutters as specified in SSR part-I section 8, clause 8.24 (a) complete all as specified and directed.

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixing all as specified and directed.

S&F 30mm thick PVC factory made panelled door shutter as per IS- 4020 made from MS tube of top and bottom rods. MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on plain side & as gap insert for top and bottom rail. Pannelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawings.

S&F box type steel windows and ventilator double frame including grill (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 Nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes complete all as specified and directed. Note :- The quoted rate a shall also include. (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 Nos MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii) PCC block for embedding lugs

Material and labour for preparation of pre-primed steel surface and applying two coats of synthetic enamel paint complete all as specified and as directed.

S&F 100mm size MS butt hinges medium weight cold rolled.

S&F 150mm long aluminium handles cast type, anodised, complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed as specified.

S&F Aluminium alloy, anodised, sliding door bolt 200mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedstaple plate and fixed complete all as specified and directed.

S&F of 300mm long mild steel ordinary rat tail rod pattern springs including roller & roller plate complete all as specified & directed.

S&F 2nd class HW small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and including all necessary labours articles n.exc 200 Cum each all as specified and directed.

S&F 100mm long hasp and staple, aluminium, wire type, including bolt to hinges plate and fixed with screws all as specified and directed.

S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified.

S&F of wire netting as chicken wire mesh of galvanised steel wire 0.71mm dia and size of mesh 25mm for cracks fixed with nails etc complete all as specified and directed.

M&L Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples all as specified and directed.

Material and labour for two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer to new steel surface including preparation of surfaces exceeding 10cm with or girth complete all as specified and directed.

Material and labour for two coats of synthetic enamel paint over a coat of primer to new wooden surface including preparation of surfaces exceeding 10cm with or girth complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material and labour for joint free Non-skid coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with including screed bed in CM 1:6, 15mm thick for laying floor tiles, etc complete all as specified and directed.

M&Lcoloured glazed ceramic tiles 450x300x7mm thick on vertical surface such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in colour cement to match including 10mm thick cement plaster with cement mortar 1:4 all as specified and directed.

M&L 20-25 mm thick cuddapa prepolished stone over and including 10 mm thick cement mortar (1:4) bedding laid & jointed with slurry cement mixed with pigment to match the shade of the slab including rubbing and polishing, rounding to edge of stone slab one edge, such as steps, cooking platform and similar situtions all as specified and directed. (Note - Hole in stone slab for accomodate the gas pipe where required complete.

Supply and fix in repair moulded polythene water storage tank of 500 ltr capacity hosted and fixed in position and float valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s/ 25mm-455gms/ 40mm- 690 gms) and tank Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm-45gms /25mm- 65gms) complete including dismantling water tanks of capacity exc 500 and n exc 1000 ltr complete all as directed.

S&F in repair Gun metal, globe or gate valves for 15 mm dia bore pipe with iron wheel head, screwed both ends for iron pipe and fixed in repair etc complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves for 20 mm dia bore pipe with iron wheel head, screwed both ends for iron pipe and fixed in repair etc complete all as specified and directed.

S&F in repairs stainless sinks without drainage board 1 mm thick kitchen or laboratory with plug washers and waste pipe including fixing contilever bracket and connecting union to pipe over all size 495 mmx 420 mm bowl size 410 mm x 330 mm x 160 mm all as specified and directed.

S&F in repair pillar taps 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes and fixed for 15mm dia all as specified and directed.

Taking down GI tubing 15mm bore of any description including cleaning for refixing or removal to store all as specified and directed.

All as per item No. 56 here-in-before but 20mm bore.

M&L GI tubing 15mm dia medium grade galvanized, with all fittings fixed complete to walls and ceilings or laid in floors.

All as per item No. 58 here-in-before but 20 mm bore.

Refixing old GI pipe 15 mm bore & connections in new or old position to walls and ceiling or laid in floor all as specified & directed.

Refixing old GI pipe 20 mm bore & connections in new or old position to walls and ceiling or laid in floor all as specified & directed.

S&F in repair 15mm bore bib tap chromium plated fency type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F in repair 15mm bore angle valve /stop valve chromium plated fency type cast copper alloy screwed down high pressure, crutch or butterfly handle, screwed both end for pipe or for unions complete chromium plated with suitable type as directed

Supply and fixed in repair stop valves, 15mm dia, cast copper alloy,CP fancy type with long shank and cup (concealed type) screwd down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe all as specified and directed.

S&F in repair PVC low level 10 litre capacity valveless syphonic action type white flushing cistern with inlet ball valve float and handle including brackets and necessary fittings etc fixed in repairs complete.

S&F vitreous china squatting pan Orissa pattern size 580 x440mm white with integral footrest, including trap set and conection to trap, flushing pipe etc complete including making good to floor all as specified and directed.

S&F in repair WHB white size 550x400mm vitreous china (flat back or angle back type) any size,including cutting for and pinning end of bracket or eracting stand but exclusive of fixing of supply and waste pipe complete.

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats. (Minimum weight 190grms) all as specified and directed.

S&F PVC connection 15mm bore size with PTMT nuts of length 450mm long all as specified and directed.

S&F 40mm dia PVC pipe low density (LDPE) of pressure 6kg/CM2 fixed to wall or laid in floor as waste pipe.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws

S&F swivel shower of PTMT any colour for fixing with 15mm pipe (Minmum weight 40gms) complete all as specified and directed.

S&F 75 mm out let PVC (SWR) floor trap with plain grating including Jointing to waste pipe and fixed in solvent cement complete all as spcefied and directed.

Demolition and breaking up or down PVC /AC/CI /Cement rain pipe fixed in any position internal dia of pipe 100mm all as specified and directed.

S&F 110mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall complete all as specified.

S&F 75mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall complete all as specified.

S&F PVC (SWR) bends 110 mm dia provided with access door all as specified and directed.

S&F PVC (SWR) bends 110 mm dia all as specified and directed.

S&F PVC (SWR) bends 75 mm dia all as specified and directed.

S&F PVC (SWR) bends 75 mm dia provided with access door all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia all as specified and directed.

Demolition of reinforced cement concrete in floors, beams, chajjas, landing slab in any position or height and similar suspended works including removal of debris to a distance not exceeding 100m as directed by Engineer-in-Charge.

M&L for cement concrete 1:2:4 type B1, using 20mm graded stone aggregate in lintels upto 1.5m clear span, Chajjas, cills, steps, seismic and other similar bands, Beams, plinth courses, string courses, lacings courses, parapets and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating including use of necessary formwork as directed.

M&L 10mm dia and over TMT bar, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia) including welding, rivetting etc complete.

M&L cleaning surface of sunken portion wall/bottom and applying cement slurry @1.2 Kg per Sqm and applying 15 mm thick cement plastered in CM 1:3 finished even and fair using extra cement and applying two coat of acrylic polymer modified cementious slurry as per manufactureas instruction to make the surface leak proof complete all as specified and directed.

S & F Curtain rails 20mm dia fix in repair, mild steel, chromium plated with fixing brackets, stops, rollers and finnels etc and with all necessary fittings complete all as specified and directed.

Demolition brick work or stone / boulder masonry built in cement mortar as in wall etc complete including removal of debris to a distance not exceeding 100m as directed by Engineer-in-Charge all as directed.

M&L for brick work with sub class 'B' brick modular size in CM 1:6 straight or curved on plan exc 6m mean radius as in parapet wall etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including necessary forms mould mitred /stopped ends etc all as specified and directed.

M&L PCC 1:3:6 type C2 (using 40mm graded aggregate) in Surface channel or drains including necessary form works, stops, moulds etc incl demolition of concrete all as specified and directed.

S&F for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel' complete all as specified and directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in chajja roof covering/cladding to wall, fixed with self tapping screws as specified with 'J' or 'L' hook / suitable screw complete all as specified and directed.

M&L for heavy duty exterior grade tile texured finish of 300X300X10 mm thick mic/vitrified tile laid over and including 10 mm thick rendering in CM 1:4 as in steps complete all as specified and directed.

S&F 18/19mm thick prelaminated particle board interior grade, prelaminated on both side with decorative choice lamination fixed with screws to timber frame work as in cupboard shutter including teak wood beading complete all as specified and directed.

Taking down/removing the existing roof treatment including backing coat if any and disposal of debris to a distance not exceeding 100m as directed by Engr-in-Charge M & L for rendering in CM 1:4, 10 mm thick over roof surface finishing fair and even without using extra cement including mixing with WPC as per manufacture instructions and M&L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment/ specification from bottom to top all as specified and directed. (a) Applying bituminous primer @0.30 litres per Sqm over plastered surfaces of roof including parapet surface. (b) One layer of APP based polymeric membranes of approved manufacturers, 3mm thick, weight not less than 3.6 Kg/Sqm, reinforced with non woolen polyester fabric or weight not less 150 gms/Sqm complete all as per manufactures instructions. Note : - (i) Laying of APP based membranes shall be executed through authorised applicator. (ii) A minimum over lap of 100mm and 75mm should be made in the end sides of polymeric membranes respectively and sealed all over laps and joints as manufacturer’s instructions.

M&L for 40 mm thick (average thickness) PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregate as in roof padding laid in two layers of 20 mm each including. welded wire mesh will be placed between two layers of concrete and finished fair/ even with out using extra cement complete all as specified and directed. False groove shall be made in top surface of concrete complete all as specified and directed.

Taking down carefully aluminium/copper point wiring with surface/ concealed PVC conduit or wooden batten (light, fan, socket, bell or power) including sunk in cast iron / pressed steel terminal boxes except fitting such as switches, ceiling roses, lamp holders, sockets, regulators, call bell, light fitting any sketch etc and making good disturbed surfaces of walls, floors etc complete.

M & L for Point wiring with PVC insulated 1.5 Sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed rigid non mettalic PVC conduit medium grade (make of conduit-Presto Plast/Pressfit) not less than 19/20 mm ( ISI marked ) with all fitting and fixing accessories , modular cover plate with frame including sunken boxes suitable to fix modular cover plate with frame , concealed in wall & machine the existing surface etc complete (Make of cable-Finolex/Havells/Policab) all as specified and directed for One light point/fan point controlled by one switch.

All as per item No. 99 here-in-before but one light point controlled by two way switch.

All as per item No. 99 here-in-before but one socket outlet 5 Amps controlled by one switch on the same board.

All as per item No. 99 here-in-before but one socket outlet 5 Amps controlled by one switch on independent board.

All as per item No. 99 here-in-before but one bell / buzzer controlled by one bell push.

All as per item No. 99 here-in-before but with 2.5 sq mm multi stranded copper conductor cable for one 15 Amps socket outlet controlled by one switch on independent board and 1.5 sq mm PVC insulated multisranded copper conductor cable as continuous earth wire complete.

Supply and Fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP/DP 10A- 20 Amps with complete accessories all as specified and as directed and directed by Engr in Charge as per site requirement.

Material and labour in repairs for sub main wiring with two single core 4 sqmm multi stranded copper conductor, FRLS PVC insulated, unsheathed cable including rigid non metallic PVC conduit medium grade, ISI marked, 20 mm dia for sub main wiring including 2.5 sqmm FRLS PVC insulated and unsheathed stranded copper conductor as earth wire in conceled in wall of make & maching the existing surface make & maching the existing surface and making good to the disturbed surfaces to match the existing surfaces complete including taking down of existing sub main wiring all as specified and directed. Note :- Two runs of 4 sqmm copper conductor cable, one run of 4.0 sqmm copper conductor and one run of PVC conduit will be measured as one unit.

S & F ceiling rose surface bakelight two to three terminal.

S & F Ding Dong bell AC, 240 volts single pole complete.

S & F Modular Bell push 6A 1 module complete.

S & F Fan step regulator, 120W, 240 volts 2 module

S & F Modular switch 1 way 10A, 240 volts 1 module complete.

S & F Modular switch 2 way 10A, 240 volts 1 module complete.

S & F Modular switch 1 way 16A, 240 volts 1 module complete.

S & F Socket, 6A - 2/3 pin combined 2 module complete.

S & F Socket 6A/16A - 2/3 pin combined 2 module

Supply and fixing Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete including 5 W LED bulb all as directed.

S & F Endura Linear Neo surface and wall mounted LED batten 20 Watt, extruded aluminum housing for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver environmental friendly, energy efficient ready to use pack housing with reflector cover channel, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make- Havells cat Part No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent to Philips/Crompton/Bajaj/Wipro

S & F Decorative Endura Linear Neo LED lighting fixture 10 Watt, 6000K, (581 mm) with extruded Al. heat sink, environmental friendly, energy efficient ready to use pack housing with reflector cover channel, with electronic driver, holder, including LED tube 10 Watt connector block, etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make - Havells Cat Part No. LHEWEBP7IN1W010 or equivalent to Philips/Crompton/Bajaj/Wipro

Supply & fixing for Bulkhead fitting LED 08 watt (RUGBY) type complete and fixing to wall / ceiling including fixing arrangement with clamps/ screws/nuts/ bolts /washers etc connecting with provision of flexible cable of 1 mtr length connection with 0.5 Sqmm PVC insulated twin core multi stranded copper cable complete including taking down existing unservicable lighting fixture of any type and size all as specified and directed. Make : Havells Cat Pat No. LHKL01160099 or equivalent to Philips/Crompton/Bajaj/Wipro

Taking down MCB DBs /MCBs of all sizes after disconnecting supply complete all as specified and directed.

S & F sheet metal enclosure MCB DB 4 way tripple pole and neutral 415 volts including taking down the existing complete.

Supply and Fix for sheet metal enclosures for SPN DB's 240 volts, factory made double door flush type, IP-42 protection and all as per IS-8623, made from sheet metal 12 way 200 Amps rated bus bar to be fixed with wall all accessories including taking down the existing complete all as specified and as directed.

S & F MCB single pole 240 volts 6 to 32 Amps including taking down the existing complete.

S & F MCB double pole 240 volts 16 to 40 Amps including taking down the existing complete.

S & F MCB TPN 63 Amp 440 Volts including taking down the existing.

Earthing complete with glavanised steel earth plate elactrode 600x600x6.0 mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground leves) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut, bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber , reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate No. 3 of MES SSR Pt-I 1991 print and as directed.

Materials & labour in replacement of 1100 Volts grade heavy duty XLPE cable of size 25 Sqmm 4.0 Core, passing through GI pipe with aluminium conductor stranded polyethylene insulated conductor served with and including sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed including removing existing UG cable of any size all as specified and as directed.

Excavation in trenches in any type of soil (loose/ hard) not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth and getting out for foundation of pole, laying under ground cables etc and getting out complete all as directed.

Returning filling in with the earth obtained from above item including spreading, levelling, watering and well ramming in layers and not exceeding 25 cm in layer complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 Mtr and deposting where directed at a level not exceeding 1.5 Mtr above the starting point all as directed.

M & L sand filling in trenches for cable cushioning with clean, dry and unwashed sand free from sharp particles including gently punning around cable complete all as specified and directed.

M & L Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete all as specified.

M & L of GI pipe light grade 80mm dia bore with all fittings and fixed complete to wall, to pole or laid in trenches and road crossing complete including removing of existing GI pipe of any size and shape all as specified and directed.

M/s SHIVRATAN CONSTRUCTION

Dashmesh Enterprises

TANUJ CONST. CO.