SPL REPAIR OF SECURITY WALL NEAR FLAG POST BLDG NO P51 AND P52 OF HQ NC PROVN OF HARDSTANDING AND ALLIED WORKS OPP REZANGLA MAIN GATE HARDSTANDING AND MISC WORKS (NEAR LOWER PARKING) AT HQ NC AND CERTAIN REVENUE WORKS UNDER GE SOUTH UDHAMPUR

Amount

Taking out any type of cables, pipes or any type of utilities found above or benith the ground level and laying/reconnecting the same away from working area/site, including material and labour utilised in the same complete all as specified and directed.

Taking down existing aluminum cabins and refixing the same after necessary repairs etc. complete all as specified and directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, built in cement mortar etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core etc. to store and rubbish not exceeding 50 m complete all as specified and directed.

Taking down cement plaster on brick/stone wall etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Dismantling of AC or reinforced concrete pipes, jointed in cement mortar pipes up to 100 mm bore in any position complete all as specified and directed.

Hacking out old broken glasses (Any thickness, size quality, description) from wooden or steel frames fixed with putty or wooden beads complete all as specified and directed.

Demolition of Brick/stone work built in cement mortar of any descrption complete all as specified and directed.

Taking down chowkhat or frames exceeding 1.50 Sqm but not exceeding 4 Sqm (without taking down shutters from the frames) complete all as specified and directed.

All as per ser item No 8 here in before above but not exceeding 1.50 Sqm complete all as specified and directed.

Taking down shutter only exceeding 1.00 sqm but not exceeding 2.00 sqm and refixing the same opening after easening and repair complete all as specified and directed.

Taking down shutter only exceeding 1.00 sqm but not exceeding 2.00 sqm complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick below or above ground level complete all as specified and directed.

Disconnecting water tanks and refixing the same after cleaning etc exceeding 250 ltrs and not exceeding 500 ltrs complete all as specified and directed.

Taking up or down steel tubing 15 mm bore including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore including cleaning for refixing or removal to store complete all as specified and directed.

Providing and injecting chemical emulsion for Post constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 ltr per sqm of the vertical surface of the sub structure to a depth of 300 mm including excavated channel along the wall and rodding etc complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Providing and injecting Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Providing and injecting of voids in masonry using chemical emulsion one litre per hole, at 300 mm intervals including drilling holes complete all as specified and directed. Note : The treatment work shall be carried through authorised agency only and certificate for the same for warranty shall have to frunished before submitting payment and drilling holes at 45 degree and plugging the same with cement mortar 1:2 to match with existing surface.

Providing at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment.

Reinforced cement concrete M-25 Nominal mix (using 20 mm grade aggregate) as in beams, cantilevers over span 1.5 m landings, balconies etc. complete all as specified and directed.

TMT steel bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with m.s wire annealed not less than 0.9 mm dia complete all as specified and directed.

All as per ser item No 22 here in before above but 5 mm dia and over up to and including 10 mm dia as in stirrups complete all as specified and directed.

Brick work with sub class 'B' bricks exceeding 6 m mean radius straight or curved on plan built in cement mortar 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 Metre mean radius to half brick thick in cement mortar 1:6 complete all as specified and directed.

15 mm thick rendering on fair faces of brick surfaces finished even and smooth without using extra cement in cement mortar 1:4 including mixing of WPC complete all as specified and directed. Note : WPC to be measured and paid for for seperately.

15 mm thick rendering on brick or concrete surfaces in cement 1:6 finished even and smooth without using extra cement complete all as specified and directed.

10 mm thick rendering on concrete surfaces (as in facia and corbelling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed.

5 mm thick rendering on concrete surfaces (as in soffits of ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed.

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20 mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing complete all as specified and directed.

35 mm thick second class hard wood plain framed pannelled shutter (two panels) with lock rail and pannel or 9 mm BWP comerical ply or 12 mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned complete all as specified and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

All as per ser item No 33 here in before above but wire gauge windows complete all as specified and directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty in Squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Stainless steel wire cloth 0.35 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and directed.

300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

100 mm long butt hinges medium weight and fixed complete all as specified and directed.

Steel locking bolt with mild steel electrogalvanised plate and bright bolt not less than 10 mm dia 100 mm size complete all as specified and directed.

Aluminium anodised barrel tower bolt of extruded section and fixed length of bolt 150 mm complete all as specified and directed.

Aluminium handle, cast type anodised size of handle 150 mm complete all as specified and directed.

100 mm bore CI sand cast iron pipe in any length with or without ears laid in trenches or in floors complete all as specified and directed.

75 mm bore CI sand cast iron pipe in any length with or without ears laid in trenches or in floors complete all as specified and directed.

All as per ser item No 43 here in before above but 50 mm bore fixed to walls complete all as specified and directed.

Cast iron cowl 50 mm bore complete all as specified and directed.

100 mm bore CI sand cast iron branch piece single (equal or unequal) oridinary or inverted with paralel branches complete all as specified and directed.

75 mm bore cast iron floor trap with grating including jointing to waste pipe fixed cement concrete type B-1 (1:2:4) complete all as specified and directed.

Sand cast iron bend (any radius) 100 m bore dimnishing pieces or tapers (larger bore measured) fitted with oval acess doors complete all as specified and directed.

All as per ser item No 48 here in before above but 75 mm bore complete all as specified and directed.

100 m bore sand cast iron 'P' or 'S' trap complete all as specified and directed.

Salt glazed stone ware gully trap, square or rounded mouthed type "P" of size 150 mm x 150 mm complete all as specified and directed.

Stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 50 mm bore pipe complete all as specified and directed.

PCC type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and directed.

25 mm thick PCC type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

15 mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado complete all as specified and directed.

10 mm thick non skid coloured vitrified tiles (area of each tile exceeding 0.18 and not exceeding 0.38 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Glazed ceramic colored tiles as in vertical surfaces 350 x 250 x 7 mm/450 x 350 x 7 mm /300 mm x 600 mm thick set and jointed in neat cement slurry and pointed with white or colored cement to match complete all as specified and directed.

Drapery rod powdered coated complete all as specified and directed by Engr-in-Charge.

Wooden finish brackets and end stops of approved finish complete all as specified and directed.

Rolled mild steel angle or tee sections (Fe 410-W (Gde-E-250) quality-B) used as in framework, staging, ladder etc including welding/rivetting/nut bolting complete all as specified and directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories complete all as specified and directed.

20 mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule complete all as specified and directed.

20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified and directed.

15 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified and directed.

Viterous china wash down water closet pan pan (pedestal pattern), white (excluding flushing cistern, flush pipe complete all as specified and directed.

PVC white seat cover including all necessary hinges complete all as specified and directed.

PVC Valveless syphonic action type flushing cistern, low level, white with inlet, ball valve, float and flushing device, soft touch type complete connection to pipe in repair complete all as specified and directed.

WHB coloured 615 mm x 510 mm with pedestal complete all as specified and directed. Make : CERA CARNIVAL Cat Part No (WHB 1009, PEDESTAL 1108)/Prayag/Hindware.

Half stall urinal flat back (large) 635 x 395 x 420 white colour complete all as specified and directed. Make : CERA Cat Part No: 5001/ Prayag/Parryware.

CP waste coupling 32 mm dia PTMT (half or full threaded) minimum weight 450 gms complete all as specified and directed.

PVC waste pipe 32 mm bore with cup and washers complete all as specified and directed.

15 mm bore centre hole basin mixer with round spout with 450 mm long copper pipes and brass nuts with out Pop up complete all as specified and directed. Make: Jaquar, Cat Part No : CON 167KNB/CERA/Prayag.

Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and directed. Make : Jaquar Cat Part No : PRS 077/ CERA/Prayag.

15 mm bore Bib tap complete all as specified and directed. Make : Jaquar, Cat Part No : CON-107KN/CERA/Prayag.

15 mm bore angular stop cock with wall flange complete all as specified and directed. Make : Jaquar, Cat Part No : CON- 059KN/ CERA/Prayag.

PVC connection 15 mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring and Rubber washer (Suitable for Basin Mixers) complete all as specified and directed. Make : Jaquar, Cat Part No - ALD-803AB/ CERA/Prayag.

PVC connection 15 mm bore 450 mm long Braided Hose with two 15 mm Nut and Rubber washer without nipple complete all as specified and directed. Make : Jaquar, Cat Part No - ALD-805B/CERA/Prayag.

Hand shower (health faucet) with 8 mm dia 1.2 meter long flexible tube with wall hook complete all as specified and directed. Make : Jaquar, Cat Part No - ALD-573/CERA/Prayag.

Chromium plated toilet paper holder complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1153N/CERA/Prayag.

Glass shelf with chromium plated guard rails complete all as specified and directed. Make : Jaquar, Cat Part No : ACN-1171N/ CERA/Prayag.

600 mm long brass chromium plated towel rail fancy type complete all as specified and directed. Make :Jaquar, Cat Part No : ACN-1111NM/CERA/Prayag.

Soap dish complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1131N/CERA/Prayag.

Double Coat hook complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1161N/ CERA/Prayag.

Cutting outting out 100 mm bore hole and fixing 100 mm bore CI connector so as to connect 110 mm bore PVC rain water pipe with and including fixing to clamps complete all as specified and directed.

110 mm bore PVC (SWR) pipe single socketed in any length with rubber joints fixed to walls complete all as specified and directed.

110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 40 mm thick PCC and 15 mm thick plastering in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg /Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Minimum weight of membrane will be 3.5 Kg/ Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg /Sqm and including two coats of bituminous Aluminium paint complete all as specified and as directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and directed.

Supply only (LW+) water proofing liquid solution complete all as specified and directed.

Preparation of surfaces of old or new surfaces including removal of old treatment and applying a thin layer of Birla white putty to give a uniform finish as approved and complete all as specified and directed by Engr-in-Charge and required at site.

Preparing of old/new wall surfaces and applying two coats of cement base paint complete all as specified and directed.

Preparing old/new plastered surface of wall and applying two coat of oil bound distemper complete all as specified and directed.

All as per ser item No 95 here in before above but on ceiling complete all as specified and directed.

Preparation of old/new plastered surfaces and applying two coats of weather proof exterior emulsion paint any color complete all as specified and directed.

Preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Preparation of on old wooden surfaces surfaces and applying one coat of synthetic enamel paints complete all as specified and directed.

Preparation of pre-primmed surface and applying two coats of synthetic enamel paint on new steel surfaces complete all as specified and directed.

Powder coated/Anodised aluminum alloy door window frames, other sections for doors, windows, ventilators with one or more rebates, channel for sliding shutters, grills etc including jointing cleats for fixing etc. complete all as specified and directed. Make : Jindal, Hindalco

Powder coated aluminum American handle cast type 200 mm for doors complete all as specified and directed.

Powder coated aluminum handle cast type 100 mm collapsible type complete all as specified and directed.

150 mm long aluminum tower bolt complete all as specified and directed.

75 mm size butt hinges, extruded aluminum alloy ISI marked complete all as specified and directed.

100 mm size butt hinges, extruded aluminum alloy ISI marked complete all as specified and directed.

Supply only rubber gasket for fixing of glass complete all as specified and directed.

Aluminum door closer (aluminum extruded section) hydraullically regulated, designation No 3, universal type, suitable for door shutters of 851 mm to 1000 in width and of weight 61 to 80 kg complete all as specified and directed.

Stain less steel wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminum stapples complete all as specified and directed.

Brass mortice lock four levers (Harrisons) vetrical type size 100 mm or above complete all as specified and directed by Engr-in-Charge.

5 mm thick PVC sheet of design as approved in partitions, door panel etc. complete all as specified and directed.

Sand blasting to glass including glass of approved design and pattern complete all as specified and directed.

12 mm thick toughened glass door with and including heavy duty floor spring top hinge including pivot clamps, side locking arrangement, stain less steel 300 to 400 mm long handles complete all as specified and directed.

Stain less steel as in framing for fixing of glazed partition/windows or doors stc as per site requirement confirming to Gde 304 complete all as specified and directed by Engr-in-Charge.

Stain less steel clamps for fixing of glass as in partition of doors etc. complete all as specified and directed.

Itching to toughened glass to required design as approved and complete all as specified and directed by Engr-in-Charge. Note : Glass has to be paid and measured for deperatley.

Vitrified ceramic tiles 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per ser item No 118 here in before above but in vertical surfaces complete all as specified and directed.

20 mm thick Granite (of any type) tiles machine cut, in skirting, dado or at any place as required, laid over cement screed and jointed with grey cement slurry and pointed with white or grey cement with admixture pigment to match the shade of slab complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 m and depositing at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base and mass concrete complete all as specified and directed.

25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm grade crushed stone aggregate) as in floor finished even and fair complete all as specified and directed.

Cement concrete rich colored chequered tiles machine pressed with imported pigment finish (mirror/rough cast) of size 300 mm x 300 mm x (30 to 40 mm) thick set and jointed with neat cement slurry complete all as specified and directed.

PCC 1:2:4, type B-1 (using 20 mm graded stone aggregates) as in coping complete all as specified and directed.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

Dismantling old unserviceable barbed wire/ fencing wire mesh including removing from site complete all as specified and directed.

Excavation over areas not exceeding 1.5 m and not exceeding 3.00 m in depth getting out as in any type of soil complete all as specified and directed.

Reinforced cement concrete (Design mix) (20 mm graded aggregate) using footing, foundation beams, plinth beam, roof beam, lintel band, retaining wall/toe wall and similr work etc. complete all as specifed and directed by Engr-in-Charge.

Reinforced cement concrete (Design mix) (20 mm graded aggregate) using columns, pillars and similar work etc. complete all as specifed and directed by Engr-in-Charge.

Reinforced cement concrete (Design mix) (20 mm graded aggregate) using beam, cantilevers, bressummers, lintels and similar work complete all as specifed and directed by Engr-in-Charge.

Use and waste of form work to sides of footings, beam and similar work rough finished flat surfaces complete all as specified and directed.

Use and waste of form work to sides of retaining wall and similar work etc rough finished surfaces complete all as specified and directed.

Use and waste of form work to pillars, coloumn and simiar work etc rough finished surfaces square, retangular and polygon complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia as in reinforcement cut to length, bent to shae required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (anealed not less than 0.9 mm dia) complete all as specified and directed.

Brick work with sub class 'B' brick straight or curved on plan exceeding 6 m radious in cement mortar 1:4 as in brick work/brick pillars etc. complete all as specified and directed.

Preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick as in soft/loose soil complete all as specified and directed.

Removing excavated soil to a distance exceeding 50 m and not exceeding 1.50 km out side defence land complete all as specified and directed by Engr-in-Charge.

Hand packing (any thickness) of broken stone or boulder at back of walls over arches etc and raising (or lowering) to the required level complete all as specified and directed.

110 mm dia PVC (SWR) pipes single stack in any length as in weepholes of retaining wall complete all as specified and directed.

Mild steel confirming to grade Fe-165 (Fe-290) angle post or struts in fencing fixed independently including cutting and bending to shape as directed drilling holes, notching for wire etc. complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and directed.

Concertina coil 500 mm dia and 150 mm prolong fixing to any type of standard rails including screwing in position complete all as specified and directed.

Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of post including securing and tying at crossing with and provision of galvanised mild steel wire staple or steel pins etc complete all as specified and directed. (Each line wire to be mesured)

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

75 mm thick PCC 1:4:8 type B-2 (using 40 mm graded aggregate) as in sub base of floor etc complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-1 (using 12.50 mm graded aggregate) as in level course on floor etc complete all as specified and directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and directed.

Vitrified tiles, area of each tile not exceeding 0.36 sqm, 10 mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing shade of tiles complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 on vertical surfaces/backing coat complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out in hard/ dense soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide and getting out in any type of soil complete all as specified and directed.

PCC 1:5:10, type E-2 (using 40 mm graded crushed stone aggregate) as in sub base and mass concrete complete all as specified and directed.

PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in mass concrete, hold fast and similar work complete all as specified and directed.

Steel work in tubular trusses/vertical posts including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St.-240 complete all as specified and directed.

Rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding gates, doors fixed with angle cleats or other connecting plates complete all as specified and directed.

Mild steel screw bolts with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut not exceeding 5 cm long dia of shank 11 to 15 mm complete all as specified and directed.

Mild steel screw bolts with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut not exceeding 30 cm long dia of neck not exceeding 12 mm complete all as specified and directed.

Plates (plain or chequered) channels square cut or notched oridinary or counter sunk forming holes without any attatchment complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of and colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixing with self tapping screws complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of and colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixing with self tapping screws complete all as specified and directed.

60 mm thick machine pressed precasted concrete interlocking tiles/paver blocks with designer of self impression and topping of imported coloured desired pigment any shape size confirming to IS 15658-2006 of M-35 grade laid over sand cushioning up to 50 mm thick with grey cement or mixed with pigment complete all as specified and directed by Engr-in-Charge.

100 mm thick PCC type B-2 1:2:4 (using 40 mm graded crushed stone aggregate) as in floors laid in alternate pannels finished even and smooth without using extra cement and surface vibrators complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coats cement base paint complete all as specified and directed.

Plain cement concrete type C-1 1:3:6 (20 mm graded aggregate) complete all as specified and directed by Engr-in-Charge.

Preparation of new plaster surface of walls and applying two coats of plastic emulsion paint over one coat of primer and two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surface and applying two coats of oil bound distempering over a coat of primer complete all as specified and directed.

Complete removal of existing treatment on walls, preparing newly plastered surfaces of walls and applying two coats of acrylic distemper over a coat of alkali resistant primer complete all as specified and directed.

Vitrified ceramic tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

All as per ser item No 171 here in before above but in vertical surfaces such as skirting/dado etc complete all as specified and directed.

Second class hard wood 35 mm thick plain frames panelled door shutters (any number of pannels) with panel of timber flat on both sides or of veenerred particle board medium density wood particle boards with commercial face supplied and fitted to chowkhats complete all as specified and directed.

250 mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet sliding bolts of extruded sections and fixing bolts and sliding bolts of extruded section and fixed complete all as specified and directed.

Aluminium anodised barrel tower bolts 200 mm long extruded section complete all as specified and directed.

100 mm long but hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised, type B-21 complete all as specified and directed.

Preparation of new wooden surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm Each including iron mongery complete all as specified and directed.

Taking down frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm Each including iron mongery complete all as specified and directed.

Powder coated 15 micron aluminium door of approved design complete all as specified/directed with all fixing arrangement including providing and fixing door handle, tower bolts, mortice lock 6 lever (Make - Harrison/Godrej) one on each door and aluminium Powder coated tower bolts 200 mm long (03 Nos on each shutters) and 5 mm thick tinted glass pane of glazed shutter along with aluminium glazing beading of size 19.00 mm x 17.5 mm x 0.70 mm @ weight of 0.097 Kgs per RM including rubber gasket on both side complete alongwith neoprene lining. The member shall be made out of extended aluminium sesction comprising of :- (Size of the door shall be as per site requirement) (a) Door frame of size 95.25 mm x 44.50 mm x 1.70 mm @ 1.301 Kg/RM. (b) Shutter vertical member 85 x 44.50 x 1.56 mm @ 1.39 Kg per RM. (c) Shutter top member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. (d) Shutter bottom member 101.60 x 44.50 x 1.60 mm @ 1.301 Kg per RM. (e) Shutter lock rail member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. The actual measurement shall be taken, wastage shall be including in the rates, the above sections are from JINDAL/INDAL/HINDAICO/WALCO extruion. The contractor is at liberty to choose high section from approved make with minor variation in sizes and weight as approved. However nothing extra shall be paid for over size and over weight section also.

Aluminium powder coated frame, window shutters (glazed, wire gauge and grill) side hung with aluminium window frame or chowkhat 1.5 mm thick aluminium powder coated of size 100 mm x 44.5 mm and window shutter frames glazed and wire gauze (middle, top rail, bottom rail) and styles 1.5 mm thick aluminum powder coated of size 44.5 x 44.5 mm including powder coated aluminium grill 50 mm x 50 mm aparture and all fitting such as rubber gasket, aluminium glazing clips locking cabinet, 4 mm thick tinted glass pane for glazed shutters, stainless steel wire mesh for gauge shutter and hook and eye for each shutter fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75 mm 02 Nos each shutter, aluminium butt hinges 75 mm 02 Nos in each shutter aluminium handle 100 mm 01 No in each shutter including all accessories complete all as specified and directed.

Complete removal of existing treatment of wall surface and applying two coat of plastic emulsion paint (Shed approved by GE) over two coat of wall care putty complete all as specified and directed.

LED energy saving environmental friendly long life exclusive innovative die cast aluminium IP66 flood light of 120 watt suitable for hightlighting architectural facade and general purpose lighting including metal junction box complete all as specified and directed. Make of fitting - Havells, Cat Part No : JETAIRISFLS120WLED757SYMLTG/Syska/CG.

Taking out old unserviceable UG cable of size 16 sqmm 2 core complete all as specified and directed.

All as per ser item No 184 here in before above but 25 sqmm 4 core complete all as specified and directed.

Taking out old unserviceable MH light fittings of any capacity complete all as specified and directed.

XLPE insulated, armoured, aluminium conductor cable, 1100 volts grade, heavy duty, cross sectional area 16 sqmm 2 core, laid in trenches/ducts/through pipe complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundations of poles/stays etc. not exceeding 10 sqm area on plan and getting out in soft/ loose soil complete all as specified and directed by Engr-in-Charge.

Clean dry river sand in trenches/ducts for cushing of cable complete all as specified and directed.

Brick covering with width equal to the length of the brick as mechanical protection to cable using sub class 'B' bricks, laid flat of size 230 mm x 115 mm x 75 mm complete all as specified and directed.

Tubing 'light grade' galvanised iron of 40 mm bore laid under roads for protection of cable complete all as specified and directed.

Road cutting for laying of cable/pipe and making good the disturbed/excavated surface as per existing road including refilling the excavated material compacting, WBM and black top carpeting with bitumen and aggregate following the stone/sand on top complete all as specified and directed by Engr-in-Charge.

XLPE insulated, armoured, aluminium conductor cable, 1100 volts grade, heavy duty, cross sectional area 25 sqmm 4 core, laid in trenches/ducts/through pipe complete all as specified and directed.

jyoti parkash sharma