ONCOLOGY BLOCK TIRUPPUR

Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.- Upto 2.40m Footing Depth.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by Manual means

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15cm thick well rammed with surface vibrator, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supply and filling in foundation and basement with Gravel with a lead of 0-5 km in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with Filling Crushed Stone Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Brick work in Cement Mortar 1:5 (One Cement and Five Crushed stone sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for following including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

For Foundation and Basement

Brick work in Cement Mortar 1:6 (One Cement and six Crushed stone sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for the following including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

Damp proof course as per IS 3067:1988 with Cement Mortar 1:4 (One Cement and Four crushed stone sand) 12mm thick mixed with best approved quality Integral liquid water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used , finishing and curing etc. complete complying with standard specification - Manual Mixing

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers. (Payment for centering shall be given after the concrete is laid)

Providing and laying in position, Standardised Concrete Mix M-25 Grade using In-situ Concrete batching plant/ Ready Mix Concrete (RMC) adopting weigh batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/m3 and maximum water cement ratio of 0.50, including admixture (plasticiser /superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including Conveyance of concrete from batching plant to Work site, Electricity charges and other works & labour cost involved for concrete production, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and Six broken stone jelly) using 20mm size hard broken stone jelly for dummy columns,etc., excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete and as directed by the departmental officers. ( Dummy columns should be at least 1 metre height) -Mixing by manual means

For Superstructure in Ground Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given for the following including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

For Foundation and Basement

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

Cement Concrete 1:5:10 (One cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers) - Mixing by manual means

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

In First Floor

In Second Floor

In Third Floor

In Fourth Floor

Paving the floor with best quality Double charged vitrified Tiles of size 600x600x8mm conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with Self Designed Colour Ceramic Tiles of size 305 x 305 x 6mm conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 in Cement Mortar 1:3 (One Cement and Three crushed stone sand), with required Cement Slurry and Mortar Plasticizer, 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing with ceramic tiles of size 300 x 450 x 8mm

Dadooing with granite tiles of synthetic grey, paradise, and similar varieties of suitable size of 10mm thickness

Paving the floor with best approved quality Super Fine Polished Granite Stone Slab of size 4'x2' and above 18mm to 20mm thick of Synthetic Grey, Paradise and similar Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: [email protected] kg/m and Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Eachs.,aluminiumtower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No.,

Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the deparmental officers.. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Supplying, fabricating and fixing in position of Aluminium anodised Powder Coated of double leaves door with half panelled with 12mm thick bothside prelaminated partile board at bottom and half glazed using 5.50mm thick Plain glass at top. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m Bottom rail: 100x44.45x2.50mm@ 1.974 kg/mLocal rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m the and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 2 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 2Nos ., lock-1No.,

Door stopper with rubber bush including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete complying with standard specification and as directed by the deparmental officers...All the Alu. Section are to be anodised with matt finish under electricaly controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete. Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Supplying, fabricating and fixing in position factory made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor spring for each shutter, consealed tower bolt, suitable stainless steel locking arrangement and other necessary furniture fittings of approved quality.The verticalstyles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers

Stainless Steel (Salem Stainless Steel) Door Frame - Box Section using Stainless Steel Plate of 1.6mm thick of size of 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc including dismantling,making necessary chipping and holes in RCC columns, walls with power drills to the extent required ,including providing concrete 1:2:4 inside the box curing etc complete complying with standard specification and as directed by the departmental officers - SS Door Frame with thickness of 1.60mm.

Supplying and fixing Medium Density Fibre board (SBG I) of exterior grade of following type with thickness conforming to IS 12406 / 2003 with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for furniture fittings such as 3 nos SS 304 Grade Parliament Hinges of required Size (125mm x 150mm), 1 no Alu. aldrop 250 x 16mm, 2no Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 2 Nos Alu. Handles, 1 no door stopper with rubber bush incase of Single leaf door, cost of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification and as directed by the departmental officers - Single leaf. Type : both side prelaminated including external lipping with kiln dried soft wood Thickness : 35mm

Supplying and fixing door shutters for Medium Density Fibre board (SBG I) of exterior grade of following type with thickness conforming to IS 12406 / 2003 with 35 x 12mm T.W. on all edges with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for furniture fittings such as 6 nos SS 304 Grade Parliament Hinges of required Size (125mm x 150mm), 1 no Alu. aldrop 250 x 16mm, 2nos Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 3 Nos Alu. Handles, 2 nos door stopper with rubber bush incase of Double leaf door cost of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification and as directed by the departmental officers - Double leaf. Type : both side prelaminated including external lipping with kiln dried soft wood Thickness:35mm

Providing and fixing of 1.2mm thick Lead Lining Door for X-Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A, 50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesary accessories and fittings as per the required and as per the approval for the Department Officer

Supplying, fabricating and fixing inposition Aluminium anodised With Powder Coating of any colours matt finish louvered ventilator of size 900x600mm with outer frame section with 62x38x2mm at 1.174 kg/m and the louvered with moving arrangements made with aluminium channel of size 60x30x4mm @ 1.274 kg/m Aluminium clips 19.05x17.27/ 11.05x0.075mm @ 0.169kg/m with necessary 4mm thick plain glass panel for louvers including cost of all materials, labour and power required for fabrications, chipping dismantling making holes in RCC, masonry and made good to the original condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. The Aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for anodic film thickness of notless than 15 Microns,etc., complete

Supplying, and fixing M.S. GRILLS for open courtyard grill, grill works to doors, windows and ventilators etc, using necessary flats for inner and outer members which should be fixed or welded to masonry or column including necessary dismantling or making holes and redoing the same to original condition as directed by the departmenta officers inclusive of cost of providing one coat of best quality red oxide primer completre complying with standard specifications.

Supplying , fabricating and fixing in position Aluminium Anodised Powder coated colour mat finish Three track sliding window in all floors with Aluminium sections of Outer Frame bottom [email protected]/m,Top & vertical 92.34x29.70x1.50 at 1.066 kg/m, Shutter vertical 39x20x1.50 at 0.493 kg/m,Top & Bottom 18x36.6x1.50 at 0.439 kg/m,Vertical locking arrangement 28.94x39x1.50at0.632 kg/m, the follwing sizes with necessary accessories such as rubberbeadings, special hinges, lock, handle including supplying and fixing 4mm thick plain glass including cost of all materials , labours, power consumption required for fabrication , drilling holes in RCC colunm, slab, masonry walls wherever necessary with power drills to the required extent and make good to the original condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers.The aluminium sections are to be anodised with matt finish under electrically controlled in accordance with IS 1868 / 1962 for an average anodic film thickness 15 microns etc., complete

Supply & fixing of WPC (Wood Polymer Composite) Frame extruded with size 75mm x 50mm. The single core door made of rigid WPC compound with minimum Bulk Density of 900 KG/ Cub.Mt. & shore hardness of 55. Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. For the aesthetic appearance, the door shall be a printed digitally on one side of the shutter and the design is as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the WPC frame with 3 Nos of 5” SS Hinges and the door shall have 2 towerbolt on one side and 1 towerbolt or aldrop on other side for locking system and 2 numbers of handle on the either side of the door shutter, all made of aluminium.

Manufacturing supplying and fixing of Fully Panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames, stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided. 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 3 nos, one at the top, one at lock rail(Inner) and the other at the bottom are provided 1no. Aldrop is provided at lock rail section in the door 2 Nos of 200mm handle are to be provided. One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter conceal the gap between the two shutters. at an appropriate place in the door.

A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specification and as directed by the departmental officers. - Single leaf of size 1.00m x 2.10m.

Manufacturing supplying and fixing of Fully panelled steel door with the following specification. MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 4nos. One the top of each shutter, one at lock rail and the other at the bottom are provided. 1no. Aldrop is provided at lock rail section in the door 3 Nos of handle are to be provided, one more aldrop is provided in the inner lock rail section of the door. One rotating locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter to conceal the gap between the two shutters. at an appropriate place in the door.

A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc.,complete complying with standard specification and as directed by the departmental officers. - Double leaf of size 1.20m x 2.10m.

Fabricating Supplying and fixing in position of Aluminium anodised pwder coated colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be got approved by Executive Engineer before use.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officer

Stucco plastering 12mm thick using blue granite chips of size 10mm and below over a base plastering with cement mortar 1:5, 12mm thick, etc., complete complying with standard specifications

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers.( The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before use on work

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat on cement plastered wall surface ect., complete complying with standard specification and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Brick Jelly Lime Concrete 1:2:5 (One lime, two Crushed Stone sand and five brick jelly ) using 40mm brick jelly in Lime Mortar 1:2 using limestone and sand - 10 Cu.m for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor finish, curing, etc. complete complying with standard specification.(For flooring in toilet portioins except water closet portions)

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

Providing Polymer Coating (Water Proof Coating) for sunken Portion of toilet with following specification and the surface shall be cleaned to remove all dust, foreign, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred throughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and fixing fine polished cuddapah slab of 38/40mm thickness for cup- board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers

Providing Single Nosing to the Cuddapah slab etc., complete complying as per standard specification

Providing Double Nosing to the Granite slab etc., complete complying as per standard specification

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

For Superstructure in Ground Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

Finishing the top of roof with Combination Mortar 1:1:6 (One Cement One Lime and Six Crushed Stone Sand) 20mm thick complying with standard specification

Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia “B” class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position best quality aproved make Stainless Steel Sink of size 600 x 450 x 200mm size including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supplying and fixing position PVC Nahani Trap of size 100 x 75mm with PVC gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position white glazed European Water Closet with 10 litres capacity PVC flushing tank with all accessories of best quality and approved make with 100 mm “P” or “S” trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC flushing tank etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with “P” or “S” trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with testing for leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Construction of INSPECTION CHAMBER with following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of Fly Ash Bricks of size 230mm x 110mm x 70mm with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

0.90m X 0.90m clear size

0.60m X 0.60m clear size

0.45m X 0.45m clear size

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

160mm diameter PVC Pipe

110mm diameter PVC Pipe

75mm diameter PVC Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re- doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

160mm dia PVC Elbow

160mm dia PVC Elbow with door

160mm dia PVC Tee

110mm dia PVC Elbow

110mm dia PVC Elbow with door

110mm dia PVC Tee

75mm dia PVC Elbow

75mm dia PVC Elbow with door

75mm dia PVC Tee

Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety conforming to BIS of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - External water supply Below ground level

50mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works - Internal water supply Above ground level

50mm dia UPVC Pipe

32mm dia UPVC Pipe

25mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements (Since the labour for cutting, pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed) (The UPVC Specials should be got approved by the Executive Engineer before use on works)

50mm dia Elbow

50mm dia Tee

50mm dia Coupling

32mm dia Elbow

32mm dia Tee

32mm dia Coupling

25mm dia Elbow

25mm dia Tee

25mm dia Coupling

20mm dia Elbow

20mm dia Tee

20mm dia Coupling

32mm x 25mm dia Reducer Elbow

25mm x 20mm dia Reducer

20mm x 15mm dia Reducer

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes of 160mm dia having a pressure of 4 kg. / sq.cm including cost of necessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of “U” clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers

Four floor

Five floor

Providing Anti-Termite Treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stages to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termit mounds, making holes with crow ar, closing the holes after the treatement and including cost of chemicals, labour charges transport and storing etc., complete (The chemical should be got approved by the Executive Engineer before use on works)

Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete in bottom and sides of foundation. Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth. Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60 cms and at 60cms intervals on both. Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment.

Supplying and fixing in position 15mm dia of following taps of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

SS Elbow Action tap

CP Screw down tap

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing 50mm dia GI pipe for staircase hand rail near wet riser including labour charges for cutting, welding and fixing with MS flats (excluding cost of flat), etc., as directed by the departmental officers.

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fiber Glass framed 5.5mm thick mirror of 600 x 450 mm size , Shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality aluminium anodised towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing of SS False Ceiling for Operation theatres etc., complete complying with standard specification. (The make and brand of the stainless steel should be got approved by the Executive Engineer before use on works)

Supplying and fixing of SS Wall Cladding etc., complete complying with standard specification. (The make and brand of the stainless steel should be got approved by the Executive Engineer before use on works)

Paving the floor with best quality TACTILE PAVER type of new tek BT yellow colour ceramic tiles of size 305 X 305 X 15mm for vision impairment person laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with water resistant epoxy grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed bythe departmental officers

Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., completecomplying with standard specifications and as directed by the departmental officers.

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying , fixing and roofing with colour galvalume sheet of 0.47mm thick with all necessary accessories such as J/U bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the departmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers.

50mm thick precast slab using 20mm HBGS jelly

Manufacturing, supplying and fixing of Teakwood ornamental Entrance door of size 2.10x2.40m with the following specification. The outer frame of ornamental Entrance Door of size 150x100mm.Teak wood scantling. The door consists of openable area 1.90x2.20m with Double leaf. The each openable shutter consists of Top Panel for 1.50m.height and bottom vertical pannel in for a height of 90cm. The Shutter bottom rail is of 200x50mm.size and middle, top and side rails are of size 150x50mm.with corner designed beading works. The shutter pannel is of 50mm. thick T.W.planks with special curving works. The outer frames corners are designed border works single side for entrance outer frame and on both sides for middle frame.. The cost includes all kinds of furniture fittings, such as Brass Aldrop, Brass tower bolt, brass hinges, brass door stopper, brass handles. All the members are finshed with two coats of melamine polish outer the priming coat. (The quality of all furniture fittings should be got approved by the Executive Engineer before use.)

ELECTRICAL ITEMS

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End.

Supply and fixing of 4Feet LED 20W Fitting with LED 20W tube (HigherEnd) complete with TW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 9W LED lamp with battern holder for BH point

Supply and fixing of 70W LED High Bay fitting with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 1200mm (48") sweep BLDC ceiling fan complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod on the existing fan clamp

Supply and fixing of 450mm wall mounting air circulator fan on wall with necessary connection complete.

Supply and fixing of 300mm 12" sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supply and fixing of louvers shutters arrangements for 300mm 12" sweep light duty AC Exhaust fan.

Supply and fixing of 1X48w LED street light fitting (Higher End make) complete with 32mm dia GI pipe (Class ‘B’) complete on the existing post/wall with PVC unsheathed copper leads, MS clamps and aluminum painting. (Higher End)

Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 3nos.6A two module socket , 1 no. 6/16A two module socket , 3 nos. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A flush type wall socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection.

Supply and fixing of FP Enclosure Box with 32A FP MCB complete set in flush with wall with earth connection.

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. 63A 4P MCB - 1 no. 63A 4P 30MA RCCB/ELCB - 1 no. 63A DP MCB Isolator -3 nos. 6A to 32A SP MCB - 12 nos.

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. 63A 4P MCB - 1 no. 63A 4P 30MA RCCB/ELCB - 1 no. 63A DP MCB Isolator -3 nos. 6A to 32A SP MCB - 18 nos.

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 No 160A 4P MCCB as incoming and 2 Nos 63A 3P MCB, 6 Nos 6A to 32A SP MCB as outgoing with suitable cable end box in flush with wall with Earth connection only. Higher End

Supply and fixing of 100A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double brEak on suitable angle iron frame work with MS cable entry boxes with Earth connection only.

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion [ For 5A, Computer Plugs & Set Plugs ]

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion. [For 15A&20A AC Plugs]

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion [ For 12Way SPN MCB DB ]

Supply and run of 4 of 6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6sq.mm copper wire and making good of the concealed portion with suitable colour [ For FP Encl ]

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position. [ For 7 Seg 4 way DB ]

Supply and run of 4 of 16 sq.mm (101/0.45) PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 16 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion. [ For 7 Seg 6 way DB & VTPN DB ]

Air Conditioning

Supply erection testing and commissioning of 1.5TR (4500K.cal/hr) ABS plastic split type Air conditioner conforming to IS : 1391 (part 2- 1992 with Amdt No. 1 to 2 fitted with rotary compressor operating on refrigerant R-22 / non-CFL suitable for wall mounting for operation on 230V, 50Hz single phase AC supply with Three Star Rating as per BEE specifications and capable of performing the functions. 1. Cooling 2. Dehymidifying 3. Air cirulation 4. Filtering The installlation works for the above split type AC units include the following. 1. Mounting / fitting indoor and outdoor units at their respective locations. 2. Laying refrigerant pipe line of required length connecting both units after drilling hole / holes in the wall if required. Thickness of the copper tubing shall not be less than 0.7mm. 3. Insulating the suction pipe with expanded polythene foam 5mm tubing. 4. Laying 15mm dia flexible PVC drain pipe of throw out the condensate water being formed with in the indoor unit. 5. Leakage testing the entire system unit. 6. Charging refigerant gas in the unit. Suitable electric wiring to be provided with 2.5sqmm PVC insulated copper wire between indoor and outdoor units upto 6 meters length and up to switch with in 3 meters of locating of indoor unit.

Supply and installation of 4KVA capacity Automatic Voltage Stabilizer with time delay relay.

Supply and laying of 5/8' and 3/8' copper pipe extra beyond the AC unit

Supply and fixing of MS stand for Fixing Outdoor unit

Supply and fixing of water drain pipe line (1” PVC Pipe)

DX AIR COOLED CONDENSING UNITS: Design, Supply, Installation, testing and commissioning of 8.5 TR Nominal capacity DX Air-cooled Condensing Unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condenser coil with anticorrosion coatings, liquid accumulator, low noise aluminium propeller condenser fan with IP 55 motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification. The Unit to include built-in safety controls like HP/LP switch power quality protector, in-built thermal/temperature protection.

Supply, Installation, testing and commissioning of 8.5 TR nominal capacity factory assembled Double Skin AHU With 45 mm-45kg/cum PUF Insulated detachable panels, extruded thermal break aluminium profiles filled with PUF,panel external skin with 0.6 mm pre-plasticized sheet, panel internal skin with 0.6 mm galvanized sheet,AMCA tested DIDW backward/Forward curved centrifugal fan with EFF1 rating motor, drive arrangement with taper lock pulleys for fan and motor, vibration isolators out of heavy duty rubberized mounts,prefilters with 3ply HDPE 50 mm thick filters having an efficiency of 90% 10 Mic,6 row/12FPI deep DX copper cooling coil with copper header and Aluminium fins,GI mist arrestor, condensate coil trough with SS-304-20G insulated with 9 mm closed cell elastomeric foam, , Guard for Inspection Door, out let damper of aerofoil blades & PVC gears, and flexible fire retardant canvass complete with galvanized hardware. Each of the cooling coils will have independent distributers, electronic expansion valve kit, catch all drier, independent DX coil circuit to connectivity to each ODU circuit.

Supply and filling of non CFC Refrigrant Gas R410A.

Supply and fixing of hard drawn copper Refrigerant piping of size 11/8" (28.60mm) with necessary fitting and clamp etc.

Supply & fixing of hard drawn copper Refrigerant piping of liquid line of size 5/8” inches with necessary fitting and clamp etc…

Supply and fixing of flexible canvas connection between indoor unit and ducting and rubber pads, with ceiling Support angle rods etc…

Supply and fixing of 50mm thick anti vibrating rubber pads

Supply, Fabrication and Installation of 20G sheet Aluminium Ducting for both suction and Return arrangement insulate for operation Theatres with inter linking arrangements with necessary angle supports, anchor fasterners and threaded rods etc., as required.

Supply, Fabrication and Installation of 22G sheet Aluminium Ducting for both suction and Return arrangement insulate for operation Theatres with inter linking arrangements with necessary angle supports, anchor fasterners and threaded rods etc., as required.

Supply and Providing Thermal Insulation of 9mm thick Class ‘O’ Fire Retardant –XLPE with aluminium foil.

Supply & fixing of Acoustic insulation for Supply air duct using 10 mm thick class 1 rating Open cell nitrile rubber /XLPE insulation.

Supply and fixing of powder coated Extruded aluminium supply air grilles/diffuser with MS volume control damper for supply.

Supply and intsallation of fabricated GI plenum for HEPA filter , Necessary acess door shall be provided with a air tight locking arrangement .The supply air plenum shall be made out of GI framework

Supply, fabrication and fixing of Volume control dampers individually across the duct.

Supply and fixing of 1 inch PVC water drain pipe line on wall with suitable Clamp as required.

Supply, fabrication and fixing of suitable MS angle support frame for ceiling mounted the out door Units.

Supply, fabrication and fixing of suitable MS angle support frame for ceiling mounted the in door Units.

Supply and providing civil concrete block for mounting the air coditioning unit

Supply and providing of pipeline nitrile rubber insulation for suction line Refrigerant pipe as required.

Supply and Fixing of Microwavee filter 600mm*600mm size fine microwave mesh filter with efficiency of 5 Micron Level for return air

Supply, fabrication and fixing of Fresh air Louver made of extruded aluminium with bird screen provided with intake louvers. QUOTATON

Supply and fixing of High Efficiency particulate Air (HEPA) filter of size 8ft x6ft with 99.97% optical efficiency at .3 micron with following specification: Filter Size : 2feet x 2 feet x 1 feet Classification : H-13 Construction :Panel Type Efficiency :99.97% Optical efficiency at .3 micron Media : Micro glass fiber paper Spacers: Aluminium Initial pressure drop:25 mm W.C Final pressure drop : 75 mm W.C Duct holding capacity:4750gm/Sq.mtr Framing :Aluminium (Box type) No of pleats : 72 Filtration Area: 26.8 Sq.mtr Face Area : .372 Sq.mtr Washable : No Pleating Process : Machine Pleated Including fabrication of frame arrangements for micro filter and HEPA filter section.

LIFT Design, Engineering, Fabrication,Supply, Erection, Testing, Commissioning and handing over of 26Persons capacity Passenger cum bed lift (Gearless Lift with Machine Room) complete with the following specifications Complete set for patient utilizations. I. General Number of Lift : 1 No (a) Capacity and type 26Persons (1360kg) Capacity Passenger cum Bed lift. (b) Speed : 1 Mtr / Sec. (c) Drive : Micro Processor based VVVF (d) Size of Lift well : 2300 x 3000 (mm Wide x mm Depth ) as per IS 14665 (part I) 2000 to be constructed by PWD civil wing. (e) No. of floors : 5 ( Six )(Ground + 1 st floor + 2 nd floor + 3 rd floor + 4th floor ) (f) Total height of Travel : 19 metres / Pit 1600 mm / Head Room 5100mm. (g) No.of stops : 5( Ground + 4Upper Floor)

(h) No.of opening :5 ( Ground +4Upper Floor) (i) Construction of lift well : R.C.C. with brick masonry. (j) Power supply : AC 415/ 440 Volts, 3 phase, 50 Hz. (k) Auxiliary supply : 230V, AC supply ( Single phase ) (l) Position of machinery : Directly above the lift well. (m) Lift pit depth : 1600mm (n) Leveling accuracy : High level accuracy with smooth & jerk free travel and stopping.

II. CAR a. Size of Lift Car inside : 2000mm x 1500mm x 2200mm (MM Wide * MM Depth * MM Height) b. Design of lift car: 1.5mm Stainless Steel HAIR-LINE Finish c. Car ceiling : SS False-ceiling. d. Car floor : Granite / Marble flooring. e. Car fittings : 220V AC electric cabin fan 300mm swing (2Nos) and LED fittings. f. No. of Opening : One ,in front only g. Car Entrance : One in front only. Power operated V3F Drive, Side opening sliding stainless steel (1.5mm) Hair-line Finish Door. h. Clear opening : 1200 x 2000 (mm Wide x mm Height ) i. Landing Entrance Doors: Side opening sliding stainless steel (1.5mm) Hair-line Finish Door with provision for Emergency Exit key at all Landings.

IX. MINOR BUILDER WORK : To be done by the lift contractor. X. SCAFFOLDING WORKS : To be done by the lift contractor. XI. FREE SERVICE AND MAINTENANCE a. Guarantee : Guarantee for materials and workmanship of equipment not less than one year. b. Free maintenance : Free comprehensive servicing and maintenance during the guarantee period to be provided by the Lift contractor for 1year. And important necessary training of employees for minor maintenance works and proper handing over of lift to be done by the lift contractor. c. Preparation of Drawings and obtaining CEIG's Safety Certificate for lift approval as per lift act with payement of necessary fees to CEIG and insurance policies, If any applicable to lift. d. Site tests in accordance with IS 14665 shall be carried out at time of handing over.

XII. OTHER INCLUSIONS : Over speed Governor, phase failure and phase reversal relay, alarm bell, T. Guide brackets for car and counter weights, rubber padding under winding unit, Motor of adequate capacity, electro magnetic brake with compression springs, car safety gear, buffer, electro mechanical door locks, tubular S.S hand rail in car. Steel ladder for machine room, Emergency key, motor over load protection devices, final limit switch, position and direction indicators for car and landing entrances, main suspension ropes, counter weights, lifting joists for mounting the machines S.S. fascia plate for car operating panel & landing fixtures, fireman's switch and other necessary controls, Overload Warning indicator with audio annuouncer, etc.. complete. Site Testing in accordance with IS14665 should be carried out at the time of Handing over to the user department. Supply, operation and maintenance manual and necessary tools for operation and a set of spare parts required for 1 year to be provided. (As per SR Rate) (Make : Johnsons / KONE / OTIS)

Supply and Fixing of 16A Two-way switch in suitable Modular type GI box on wall with suitable front cover plate with connection (Higher End) (For Lift well lighting Control)

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 3 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 2.5 sq mm copper wire with painting of suitable colour. (For Lift Well Light Control)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 2 nos. 6A to 32A TP MCB & 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End (Lift)

Supply and clamping of 3 ½ x 25 sq.mm PVC LTUG armoured LTUG cable on post/wall with MS Clamps.

Supply and fixing of brass cable gland for 3 ½ x 25 Sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3½ x 25 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete .

RISING MAIN COPPER:

Supply erection, testing and commissioning of 630A 3L+N+PE, Plug in TYPE, 415V 3 Phase and Neutral sandwich Copper bus bar rising main indoor type totally dust and vermin proof with Insl F with suitable GI enclosure of 1.6mm thickness with epoxy painting of RAL7032. Rising main shall be provided with double copper earth bus bar of capacity as per specification for the entire length and cost of earth bus bar shall be included. short circuited rating of 50KA for 1sec with rigid hanger,spring hangers and wall support hanger. The detailed drawing shall be approved by the department before manufacturing. [Make: CPRI approved make]

Supply, Erection, Testing and commissioning of 630A END Feed unit with 630A 4P MCCB 50kA for 630A Rising mains.

Supply and fixing END cover for 630A Rising main

Supply and fixing of rigid hanger for 630A rising main

Supply and fixing of spring hanger for 630A rising main

Supply and fixing of Wall support hanger for 630A rising main

Supply and fixing of Flange end for 630A rising main

Supply, Testing and commissioning of tap of boxes of the following rising main including interconnecting rising main of 250A 4P MCCB suitable for terminating with 3.5C x 300 sq.mm cable

Supply and fixing of Horizontal Bend / Vertical Bend

Supply and fixing of Horizontal Offset / Vertical Offset / Combination Elbow / T Elbow

APFC PANEL

Design, Supply, Erection and testing of 200kVAR, 415Volts, 50Hz, 3phase, 12 stage switching sequence power factor correction Floor mounting dust and vermin proof cubicle panel board made of 16SWG CRCA sheet steel with 1 1/2 " x 1 1/2" 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedastal with supply and fixing of the following interior mounting capacitor chamber, Solid state relays with TM2 technology, with metering chamber and compartmentalised outgoing feeders with suitable capacity MCCB of 400A rating with rotary handle for incoming, with provision for louvers and cooling fan for proper ventilation to manage heat load.

Outgoing capacitor bank consits of 12 stages with MPP Capacitors ranging from 2kVAR to 50kVAR as detailed below: 1.stage - 2KVAR 2.stage- 3KVAR 3.stage- 5KVAR 4.stage- 10 KVAR 5.stage- 10KVAR 6.stage- 15KVAR 7.stage- 15KVAR 8.stage- 20KVAR 9.stage- 20KVAR 10.stage- 25KVAR 11.stage- 25KVAR 12.stage- 50KVAR

Bus bar: 2run of 50mm x 6mm tinned copper Metering: 1) 0-500A Ammeter with CT coil 2) 0-500V Voltmeter 3) R, Y, B indicators 4) Advanced micro controller based intelligent power factor controller with self diagnostics sensing and digital network analysis with software for momentary and saving parameter using a suitable multi-function meter and display to show the following parametes.

a.Vr-R Phase Voltage b.Vy-Y Phase Voltage c.Vb-B Phase Voltage d. Ir-R Phase Current e. Iy-Y Phase Current f. Ib-B Phase Current g. kW - Present Kilo watts h. RkVA - Present Reactive kVA Demand i. kVA - Present kVA j. pf - Present Power Factor k. Number of capacitor bank ON/OFF l. Provision of indicate the imbalanced load

m. Provision to indicate the change in phase sequence n. The APFC Panel should also have built in protection for current imbalance. o. High voltage / low voltage cut off, single phase preventer, provision for inductor coil to cater in-rush currents, line surges, current limiters, current sensor, etc, with connection complete and as per the relavant IE rules.

MV Panel:

Design, Supply, Erection, Testing & Commissioning of sheet steel enclosed, Dust & Vermin proof, 630A Single tier MV ACB Floor mounting cubicle panel made up of 1.6mm CRCA sheet steel with powder coating, segration of incoming & outgoing feeders should be with necessary clearence to terminate the outgoing cables with suitable capacity, necessary SMC. Bus bar insulator supports, base frame of 75mm x 50mm x 3mm with black colour paints, all Busbars insulated with RYB coloured heat shrinkable sleeves busbars joints are duly tinned, necessary GI bolts nuts washers and spiring washers etc., following switch gears & feeders.

E.B Incoming: 630A FP EDO ACB, shunt & UV Release - 1no, E.B. Incoming metering; 96 sq.mm Digital type Multifunction meter - 1no (VIF&KW, P.F, Demand controller. Earth fault relay - 1no, RYB indication lamps-1no. EB and Generator Busbar: 2"x½"x 2Runs copper flat per phase, 2"x½"x 1Run copper flat neutral OUTGOING: 630A FP SDF Double Break switch with HRC Fuse units - 2 Nos 400A FP SDF Double Break switch with HRC Fuse units - 2nos. 250A FP SDF Double Break switch with HRC Fuse units - 3nos. 125A TP SDF Double Break switch with HRC Fuse units - 2nos.

All Bus bar supports by using MS supported SMC insulating materials. Joints: All Bus bars joints tinned and galvanized bolt nuts with plate & spring washers. INTERLOCKING ARRANGEMENT: Both the EB & DG incomers mechanically interlocked with two lock one key system. The interconnection with the bus bars to the 630A ACB and 630A ACB should be done by using 1½"x½"x2 runs of Copper flat. The interconnection with the bus bars to the 630A FP SDF DB Switches with1½"x½" 400A SDF DB Switches with 1"x½" Copper flat and that for 250A SDF DB Switches with 30mmx6mm Copper flat and that 125A SDF DB Switches with 30mmx3mm Copper flat. And Double earth connection to all the switches should be done using No.8 SWG Copper conductor.

The buses should be mounted on the SMC bus insulator at proper & sufficient spacing between the buses as per IE rules. The bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of 6mm thick as partition. 1"x1/4"copper flat should be provided all around the panel for earth connection. Phase & Neutral copper buses should be provided with heat shrinkable sleeves using RYB & Black colours. Indicator lamps should be provided with toggle switches & Bakelite fuse unit.

The capacity of fuse switches, size and route location of the UG cable shall be superscribed on all the incoming and outgoing switches. The Panel should be mounted on angle iron frame work of size 3"x1½"x¼" MS channel provided all around the sides of the panel. The whole arrangements should be erected on a suitable masonary pedastal. (All Switches and ACBs should be with ISI mark and of Higher End make only)

Supply and run of 25mm x3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and laying of 3 ½X 400 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15mtr Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 3 ½ x 400 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 ½ x 400 Sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3½ x 400 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete .

Supply and laying of 2 runs of 3 ½X 300 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15mtr Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good [HT panel room to 630A Panel in NewBuilding]

Supply and clamping of 2runs of 3 ½ x 300 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 ½ x 300 Sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3½ x 300 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete .

Supply and clamping of 3 ½ x 185 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 ½ x 185 Sqmm PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3½ x 185 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete .

Supply and fixing of 5000 VA ONLINE (5kVA) UPS system Electrical Inverter for commercial and industrial applications with 4Nos. 12V, 150AH, Exide IT 500 Tall Tubular batteries with 2 hours back up for mentioned capacity fully load operation with battery stand with wheel angle iron frame arranged with shelf and suitable colour painting & the following features:

(1) Fully automatic change over (2) Over load indication-output cut off (3) On Inverter mode short circuit protection (4) Electronic trip for Low battery / auto release (5) Current & Voltage controlled Topology (6) Multiple PWM MOSFET / IGBT Topology and thyrister controlled (7) DC Volt meter AC Output meter (8) Harmonic distortion: 3 % for non linear load (9) Transient response: 2 % on 40 % step load Recovery time within 100msec (10) Out put power factor: 0.80 (11) Efficiency: 85 % to 95 % (12) Over load: 120 % for 10mints and 150 for sec (13) Alarm for low battery / output high / over load / trip (14) Battery charging and discharging meter (15) AC load current and frequency meter (16) LCD Meter – static by pass switch ( Microtek / Exide / Equivalent)

Earthing as per the ISI specification with an earth electrode of 2.1 mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mmx50mmx6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Please Enable Macros to View BoQ information