GE (AF)/SGR-12/2024-25 CERTAIN REPAIR TO FLOORING, PLASTERING, SANITARY FITTING, JOINERY AND OTHER MISC WORKS AT SMQ AREA UNDER GE (AF) SRINAGAR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 sqm each and credited to the contractor, complete all as specified and directed. Note: The damaged portion of the tiles/rendering shall be made good with the same material to match with the adjacent surface.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n exc 4 Sqm each and credited to the contractor, complete all as specified and directed. Note: The damaged portion of the tiles/rendering shall be made good with the same material to match with the adjacent surface.

Taking down shutters of any description size of shutter exc 1 sqm but n.exc 2 sqm and removing from site, complete all as specified and directed.

S&F 125x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast (40x3mm) etc. complete size /profile of frame as per IS, complete all as specified and directed.

S&F 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast (40x3mm) etc. complete size /profile of frame as per IS, complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified and directed.

S&F for Box type steel window double frame (glazed & gauged) made of ERW tube P- section of size 60 mm x 25 mm double rebated outer frame comprise glazed Skelton shutter door frame of ERW tube P-section size 50 mm x 20 mm with two Nos openable leaf consisting of two Nos of sash bar of T-sec 20 mm x 3 mm welded to frame with one No vertical mullion of ERW of ERW box type T-section size of 60 mm x25 mm FI 2 mm thick welded / screwed to frame for fixing of wire guage/glass including fixture and fitting like as handle, tower bolt stopper , cleat, pintal hinges, holdfast primer etc, complete all as specified and directed. (Note- sheet glass, wire mess,10mm Sqr Bar security grill will be measured and paid separately and window will be measured one side only)

S&F for Box type steel ventilation double frame (glazed & gauged) made of ERW tube P- section of size 60 mm x 25 mm double rebated outer frame comprise glazed Skelton shutter door frame of ERW tube P-section size 50 mm x 20 mm with two Nos openable leaf consisting of two Nos of sash bar of T-sec 20 mm x 3 mm welded to frame with one No vertical mullion of ERW of ERW box type T-section size of 60 mm x25 mm FI 2 mm thick welded / screwed to frame for fixing of wire guage/glass including fixture and fitting like as handle, tower bolt stopper , cleat, pintal hinges, holdfast primer etc, complete all as specified and directed. (Note- sheet glass, wire mess,10mm Sqr Bar security grill will be measured and paid separately and window will be measured one side only)

S&F 35mm thick second class hardwood, Factory made, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats, complete all as specified and directed.

S&F 35mm thick second class hardwood, Factory made, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

Preparation of newly steel surfaces of any description, not exc 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Preparation of old painted steel and iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Preparation of new wooden surfaces exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F in repairs 18mm thick plywood, grage BWR, type BB, fixed wih screws to timber frame woork, as in kitchen drawers, cupboard shutters etc., complete all as specified and directed.

S&F 0.90 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S&F in repairs 30mm width of flaps continuous (piano) hinges, stainless steel, bright finish or electrogalvanised, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts, complete all as specified and directed.

S&F 150 mm long aluminium anodised, handle of extruded section fabricated type anodised and fixed, complete all as specified and directed.

S&F 100mm size aluminium handles, cast type, anodised, complete all as specified and directed.

S&F 150mm size aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100mm size aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S&F in repairs for 140mm length floor door stopper of aluminium alloy body and tounge, anodised with hard drawn steel spring fixed in floor, complete all as specified and as directed.

S&F in repairs door strip comprising of aluminium holds & rubber strip fixed at bottom of door shutter with screws, complete all as specified and as directed.

S&F in repairs 250mm mild steel helical door spring rat tail type including collar plate and welding if required or otherwise fixed with screw on wooden frames, complete all as specified and directed.

S&F aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F aluminium window and ventilator shutters, side hung type without sash bars/ Sliding windows, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 Nos.) suitable handle (1 No.), complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading in squares not exceeding 0.50 Sqm including hacking out old, complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading in squares not exceeding 0.50 Sqm including hacking out old, complete all as specified and directed.

S&F 3mm thick figured glass, pinheaded type ordinary quality and glazing with oil putty/wooden beading in squares not exceeding 0.50 Sqm including hacking out old , complete all as specified and directed.

S&F in repairs mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 in steel/ wooden shutter of door & windows, complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, gates etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, nosing, framework of water tanks, band, straps, wind ties and similar work conforming to Fe 290 Gde-E-165, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/blankets, any thickness, including cover fillets, complete all as specified and directed.

M&L for Anodised aluminium snap grid frame work for false ceiling including hangers 6 mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long, complete all as specified and directed.

S&F 6 mm thick Non asbestos fibre cement building boards one side aluminium foil coated fixed or laid/ inserted to aluminium frame work with screws, complete all as specified and directed.

S&F in repairs 6 mm thick Plywood, grade BWR, type BB, fixed with nails or screws to timber frame work, complete all as specified and directed.

S&F in repairs for 20mm thick wooden planks of second class hard wood, planed one side and edges tongued and grooved or rebated fixed to replace old and or decayed boarding in patches including cutting out old, piecing, heading joints, complete all as specified and directed.

S&F in repairs 6 mm thick Non asbestos fibre cement building boards one side aluminium foil coated fixed or laid/ inserted to aluminium frame work with screws, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

Dismantling of Plain corrugated or asbestos steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings including ridges, hips, valleys and flashings etc, complete all as specified and directed.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating, complete all as specified and directed.

All as per Ser item No. 44.00 here in above but except sheet.

S&F 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating, complete all as specified and directed.

M&L for tightening bolts and closing bolt holes, etc.to rectify the leakage/ seepage, in old roof of corrugated steel sheets by sealing with one bitumen and one curved GI washer on either side and 6mm G.I. bolts and nuts if required, all set in stiff white lead, complete all as specified and directed.

Preparation of new zinc (or galvanised) steel and iron roof surfaces of any description over 10 cm width or girth to receive painting, by coating with mordant solution including washing and cleaning, etc and applying two coats of synthetic enamel paint over one coat red oxide primer, complete all as specified and directed.

S&F in repairs 20 mm dia Stainless steel drapery rod standard quality as approved by Engr-in-charge, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid in cement mortar of any thicknes, complete all as specified and directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 20-25 mm thick machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L 20-25mm thick kota stone slab as in riser of steps, skirting, dado and pillar laid over cement screed and jointed over and including 10mm thick backing coat in CM 1:4, complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises including removal of debries out of defence land, complete all as specified and directed.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level, complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to matcht in Skirting over and including 10 mm thick backing coat in CM 1:4, complete all as specified and directed.

M&L for Glazed ceramic tile 300 x 600 x 06-7mm thick (coloured) on vertical surfaces such as wall, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Glazed ceramic tile 450 x 300 x 06-7mm thick (coloured) on vertical surfaces such as wall, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M& L for Light shade Vitrified Ceramic tiles 08 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M& L for Light shade Vitrified Ceramic tiles 08 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in Skirting over and including 10 mm thick backing coat in CM 1:4, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc., complete all as specified and directed.

M&L for brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

M&L for 10mm thick cement plastering on fair faces in CM 1:4 on brick or concrete surfaces fair finished the surfaces even and smooth without using extra cement including taking down old plaster, complete all as specified and directed.

M&L 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick cement plastering on fair faces in CM 1:4 on brick or concrete surfaces fair finished the surfaces even and smooth without using extra cement but with using water proofing compound upto 12m height including taking down old plaster, complete all as specified and directed. (Note : WPC shall be measured and paid separately.)

Supply only water proofing compound.

M&L for 5mm thick rendering on fair faces of concrete surfaces in ceilings in CM 1:3 and finished fair and even without using extra cement including taking down old plaster, complete all as specified and directed.

Preperation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over and including thin layer (1mm thick) of wall care putty and priming coat , complete all as specified and directed.

Preperation of new plaster surface of ceiling and applying three coats of white wash, complete all as specified and directed

Preparation of new plastered or concrete surfaces of wall and applying two coats of cement base paint upto triple storey height, complete all as specified and directed.

Complete removal of existing treatment from brick walls or concrete surfaces including scraping down smoke soots, moulds, moss and trading oil and greasy spots etc including cornices, pilasters etc (Plastered or un plastered surfaces) and applying two coats of cement based paint over a coat of primer including preparation of surfaces on walls, complete all as specified and directed.

Prepartion of old decorated plastered or unplastered surfaces of wall including filling of holes, cracks and undulating surface with cement wall care putty making surface even and smooth and applying two coats of distemper oil emulsion paint (OBD), complete all as specified and directed.

Complete removal of existing treatment of walls and applying 1mm thick layer of wall care putty and prepare the smooth surface with sand paper and applying two coats of distemper oil emulsion (OBD) paint on walls, complete all as specified and directed.

Preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying two coats of white wash, complete all as specified and directed.

S&F in repairs 15mm bore steel warer tubes, 'medium grade', galvanised, with all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed.

S&F in repairs 20mm bore steel warer tubes, 'medium grade', galvanised, with all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed.

S&F in repairs vitreous china wash basin white flat back, size 550x400 mm, with & including 32mm dia PVC waste pipe and waste coupling with & including angle iron brackets of suitable size & length or erecting stand etc., complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F in repairs 32/40 mm dia bore PVC flexible pipe for wash hand basin/ urinal, complete all as specified and directed.

S&F in repairs Vitreous china squating pan, orissa pattern size 580 x 440mm and making good, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., including trap set in and including concrete, complete all as specified and directed.

S&F in repairs 10 litre capacity PVC valveless, Syphonic action type, fluhing cistern low level,white with inlet ball valve, float and handle including brackets and PVC flush pipe etc., complete all as specified and directed.

S&F in repairs 15 mm bore bib tap,chromium plated, fancy type, cast copper alloy with capstain head screwed down screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repairs 15mm bore Stop valve/angle valve, chromium plated, cast copper alloy screwed down high pressure with capstain head, complete all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

S & F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

S & F in repairs 15 mm size sink mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repairs hot and cold water mixer with swan neck for WHB, chromium plated quarter turn screwed down for pipe of bore 15mm, including necessary fittings, complete all as specified and directed.

S&F in repairs 75mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches, floors or fixed to wall, complete all as specified and directed.

S&F in repairs 110mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches, floors or fixed to wall, complete all as specified and directed.

S&F in repairs 75mm bore dia PVC floor trap (SWR) plain with grating including jointing with solvent cement to waste pipe, complete all as specified and directed.

S&F in repairs 100mm bore dia PVC floor trap (SWR) plain with grating including jointing with solvent cement to waste pipe, complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) junction single (Single T) equal or unequal, complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) junction single (Single T) equal or unequal with access door, complete all as specified and directed

S&F in repairs 110mm bore PVC (SWR) 'P’ trap, complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

S&F in repairs 500 liter capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and directed.

S&F in repairs 12mm thick wooden wall panelling of second class softwood with tongue and groove joint fixed in any position over and including wooden framework in second class softwood with plain fillets square or sectional area exc 13 Sqcm and n exc 25 Sqcm at n exc 90 cm centre to centre in both direction and including two or more coat of french polishing on all the exposed surfaces wooden panelling including taking down existing electrical fittings and re-fixing the same, complete all as specified and directed.

M&L for 100mm thick cement concrete, 1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) as flooring and finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for glossy cement concrete tiles 30 cm x 30cm x 25 mm thick with grey cement and no pigment machine pressed, set joined and pointed in neat cement slurry in roofs over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 25mm thick cement concrete, 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor finish even and rough to receive further floor finishes (tile/kota stone/ marble ), complete all as specified and directed.

M&L for 75 mm thick cement concrete, 1:4:8, type D-2, (using 40mm graded crushed stone aggregate) as in sub base, complete all as spciified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded aggregate) as in pavement/plinth protection, plinth protection shall be laid in alternate bays and joints shall be filled with bitumastic gola with 80/25 bitumen (1 part bitumen mixed with 3 part of sand) finishing surface even and smooth without extra cement, complete all as specified and as directed.

Deduction to be made from BOQ for Schedule 'A' Part-II (Credit Schedule from dismentling/taking down items) worth 1,24,543.00 during AOC. Note :- Tenderers shall not quote for this Schedule.

M/S A.R TANTRAY

M/S FAROOQ AND SONS

M/S Abdul Ahad Rather

M/S LUCKY BUILDERS

M/S UTA MOTORS

M/S M.R. Construction

M/S ABDUL REHMAN RATHER

M/S GULAM AHMAD ABDUL SAMAD

M/S LATIF AHMED MIR

M/S AIJAZ ENTERPRISES

M/S Thakur & Sons

M/S TARIQ AHMAD SHEIKH

M/S WANI AND SONS

M/S ABDUL REHMAN WANI