Construction of Common Facility Centre consisting of One Administrative Building, (double storeyed) One Double Storeyed Building, One Single Storeyed Building in RCC Frame Structure at Industrial Complex Rakh Ambtali Samba under MSME.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kind of soil

Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material : All kinds of soil :

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Filing under floor

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

CEMENT CONCRETE (CAST-IN-SITU) Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete

Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement)

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square meter on damp proof courses after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately

All works upto plinth level

All works above plinth level upto floor V level

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns etc

Suspended floors, roofs, landings, balconies and access platforms

Shelves (cast-in-situ)

Lintel, beams, plinth beams, girders, bressumers and cantilevers

Columns, pillars, piers, abutments, posts and struts

Stairs (excluding landings) except spiral staircases

plinth and string course fillets,

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Cement mortar 1:6 ( 1 cement : 6 coarse sand) Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Half brick masonry with common burnt clay (non-modular) bricks of class designation7.5 in foundations and plinth including curing in :)6.15.2 Cement mortar 1:4 ( 1 cement : 4 coarse sand

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course .

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete

40mm thick with 20 mm nominal size stone aggregate

50 mm thick with 20mm nominal size stone aggregate.

KOTA STONE FLOORING Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)

Word core of size 40LLB use 26 mm their work plinth footed

VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades,in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and fixing 1st quality ceramic glazed floor tiles conforming To IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps anddados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 11.68.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5mm thick27mm high having flanges of 20mm and 30 mm long, the perimeter ofceiling fixed to wall/partition with the help of rawl plugs at 450 mm centreto centre, with 25mm long drive-all screws @ 230 mm interval ,includingfixing of gypsum board/calcium silicate board board to ceiling section andperimetre channel with the help of dry wall screws of size 3.5x25mm at230mm c/c, including jointing and finishing to a flush finish of taperedand square edges of the gypsum board withrecommended jointingcompound, jointing tapes, finishing with jointing compound in 3 layerscovering upto 150mm on both sides of joint and two coats of primersuitable for board, all as per manufacturers’ specification and alsoincluding the cost of making openings for light fittings, grills diffusers,cutouts made with frame of perimetre channels suitably fixed all completeas per drawing and specification and direction of the Engineer-in-Chargebut excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1 : 2011 (Board with BIS certification marks)

Providing and fixing on wall face un-plasticized Rigid PVC rain waterpipes conforming to IS: 13592 Type A including jointing with seal ringconforming to IS: 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes (i)110 mm diametre

Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ringconforming to IS : 5382 leaving 10 mm gap for thermal expansion

110 mm shoe

110 mm bend

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Pcc jump

CEMENT PLASTER (IN FINE SAND)

15mm Cement plaster on the rough side of single or half brick wall of Mix 13.2.2 1 : 6 ( 1 cement : 6 fine sand)

CEMENT PLASTER IN TWO COATS

18mm Cement plaster in two coats under layer 12mm thick cement plaster 1 : 5 (1 cement : 5 coarse sand) finished with a top layer 6mm thick cement plaster 1 : 6 (1 cement : 6 fine sand)

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

White washing with lime to give an even shade on New Work (three or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Depry Roofs

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness (weight not lessthan 12.50 kg / sqm)

10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 (1clay: 1 cow dung) and covered with specified tile bricks grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finishing neat. With common burnt clay (non modular) brick tiles of class designation 10.0

Providing and laying common burnt clay (non modular) brick tiles of class designation 10 over mumty roofs grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over a 12 mm layer of cement mortar 1:3 (1 cement :3 fine sand) and finished neat.

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level andcuring complete with 7.1.1 Cement mortar 1:6 (1 Cement : 6 coarse sand)

Providing and fixing Anodized aluminum grill (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixingapproved Anodized aluminum standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment)

Water storage tanks 1000 lit

Proofing Roofs

Stainless steel railing in stairs

Dispose of earth

Sanitary Fitting

Providing and fixing white vitreous china pedestal type water closet (European type) WC pan complete with cistern and fitting complete

Providing and fixing white vitreous china flat back Urinal basin complete with flushing cistern and fitting complete

White vitreous wash basin 660 x 460 mm with pair of 15mm CP brass pillar taps etc complete

Providing and fixing 600x450 mm beveled edge mirror of superior glass complete with 6 mm thick hard board ground fixed to wooden cleast with C.P brass screws & washer complete

Providing & Fixing 600x1250x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P Brass brackets and guard rail complete fixed with 40 mm long screws rawl plugs etc

Providing & fixing Toilet Paper holder

600mm long towel rail with total length of 645 mm,78 mm wide and effective height of 88 mm, weighing not less than 190 gms

Kitchen sink with drain board

SOIL WASTE & VENT PIPES

PROVIDING AND FIXING SOIL WASTE & VENT PIPES : CENTRIFUGALLY CAST IRON S& S pipes as per 1s:3989

75 mm CENTRIFUGALLY CAST IRON S& S pipes as per 1s:3989

Providing and fixing plain bends of required degree 100 mm dia

Providing and fixing plain bends of required degree 75 mm dia

Providing and fixing bend of required degree with access door insertion rubber washer 3 mm thick bolts and nuts complete ;

100 mm dia

75mm Dia

Providing and fixing heel rest sanitary bend

75m m dia

Providing & fixing single equal plain junction of required degree

Providing lead caulked joints to sand cast iron / centrifugally cast iron pipes & fitting of diameter

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete including cost of cutting & making good the wall & floor 1860.2 :100 mm intel & 100 mm outlet

Water Supply

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. (Internal work-Exposed on wall)

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

Concealed pipe including painting with anti corrosive bit mastic paint, cutting chases and making good the wall

15 mm dia. nominal bore

20 mm diameter pipe.

Providing and fixing brass stop cock of approved quality

15 mm nominal bore

20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore

Constructing masonry Chamber of specified size, in brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 (1cement :4 coarse sand) and R.C.C. top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) including necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design Chamber 60x60x75 cm

Sewages Disposal

Septic tank 12x12 (ft)

Soakage pipe 2.4 myt dia & 2.4 mtr filled with brick bats

Constructing brick masonry road gully chamber of specified size with common burnt clay(non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4coarse sand) including precast R.C.C. horizontal grating with frame complete as per standard design: 20.23.1 Chamber size 50x45x60 cm including precast R.C.C grating with frame 500 mm with 58 kgs

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) including bed concrete as per standard design 150 mm diameter S.W. pipe

Granite stone

Steel railing stair case stain less steel.

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125 mm

ANODIZED ALUMINUM FITTINGS (All fittings shall be ISI marked)

Providing and fixing ISI marked aluminum butt hinges ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x63x4 mm

ANODIZED ALUMINUM FITTINGS (All fittings shall be ISI marked)

Providing and fixing ISI marked aluminum butt hinges ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :-