GE (N) P/TOKEN- 64 OF 2025-2026 DAY TO DAY MAINT WORKS AND CONNECTING REPAIRS OF MISC NATURE AT VISWAMITRA MARG, VICTORIA ROAD AND VARIOUS UNITS IN THE AREA OF AGE B/R (EAST) UNDER GE (N) PUNE

Labour only for opening of air locks in toilets /baths and kitchen water pipe line but excluding fittings complete all as specified and as directed.

S&F 15mm bore tubes med grade galvanized ISI marked with all fittings in short length and fixed complete to walls, floor, ceiling etc all incl taking down existing G I tubing complete all as specified and as directed

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings in short length and fixed complete to walls, floor, ceiling etc all incl taking down existing G I tubing complete all as specified and as directed

S&F in repair grating round 100 mm size of stainless steel with/without hole complete all as specified and as directed.

S&F in repair for floor door stopper of Stainless steel body and tongue not less than 100 mm anodised with hard drawn steel spring fixed in floor complete all as directed and specified.

M&L for 15mm thick rendering in CM 1:6 on bricks or concrete surfaces finishing the surfaces even and fair and provision of sagol finish with two coats of oil bound distemper of any tint over a coat of alkali resistant primer including preparation of new surface complete all as specified and as directed.

M&L for 15mm thick rendering on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing, in cement mortar (1:6) finished even and fair and provision of sagol finish including taking down existing plaster and two coats of oil bound distemper of any tint over a coat of alkali resistant primer including preparation of new surface all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing, finishing the surfaces even and smooth without using extra cement including taking down existing plaster and two coats of exterior emulsion weather proof paint paint over a coat of primer including preparation of new surface complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection, 75mm thick and finished even and smooth without using extra cement, including demolition of existing cement concrete.

M&L for 40mm thick cement concrete 1:2:4 type B-2 (using 20mm graded stone aggregate) as in floor, finished even and smooth without using extra cement, including demolition of existing cement concrete.

S&F glass dividing strips 3mm thick, 38mm wide and inserted in position to conform to design complete all as specified & directed.

M&L non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc exc. 0.06 sqm but n.exc. 0.09 sqm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 20mm thick screed bed or bedding of layer in CM 1:6 and demolition of existing tiles of any description complete all as specified and as directed.

M&L coloured vitrified double charged tiles 10mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36sqm as in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 20mm thick screed bed or bedding layer in CM 1:6 and demolition of existing tiles of any description complete all as specified and as directed.

M&L glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 and demolition of existing tiles of any description complete, complete all as specified and as directed.

S&F in repair dead lock, vertical type 4 lever size 65 mm mild steel body with duplicate keys including key hole with fixing bracket complete all as specified and as directed.

M&L for machine cut cudappah stone slab 20-25 mm thick as in lintels, shelves, vertical surface, fixed with neat cement slurry mixed with pigment to match the shade of the slab or arldite, including rubbing and polishing and demolition of existing stone of any description complete all as specified and as directed

Material and labour for 18-20 mm thick telephonic black granite (of any type) work ( table rubbed and polished) in steps , jambs. pillars, window cills, cooking platforms and like in cement mortar (1:4), pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl demolition of existing stone of any description complete all as specified and as directed.

Material and labour for making hole and fixing the metalic packer for hydrophobic PU foam and sealer without disturbing existing structure as per manufacturer's instructions and forming agent like coreseal 357A/ core seal 357 CAT for carrying out non destructive water proofing treatment of sunken portion slab, floors and walls of bathroom, WC WHB and floor traps (combined unit) by using construction chemical methods such as hydrophobic PU grouting, epoxy coatings etc. including cleaning of surfaces with wire brush, detecting the sources of leakage and repairing, removing/ taking down unsound treatment/ surfaces and followed by material and labour for second course injection of resin like coreseal 135A/ 135B without disturbing existing structure complete all as per manufacturer's instructions and as directed by Engr-in-Charge. Make:Buildcore chemicals/ Pidilite/ Chemistic/ Fosrock as approved.

M&L for cleaning carefully the existing ceramic tiles with tile cleaner with jet, washing with jet water, scratching and cleaning the joint and filling the same with epoxy tile grout of white/ matching colour, curing complete all as specified and as directed. Make: STP, Asian paint, Berger paint, Pidilite, Fosrock

S&F in repair Stainless steel Hasp and staple, safety type of 100 mm long including bolt to hinge plate and fixed with Self Tapping screws complete all as specified and as directed

S&F in repair, 40mm dia, cupboard knobs fixed with nut, screw & washer of mild steel, bright finished complete all as specified and as directed

S&F in repairs for Garware Sun Control polyster film, 50 micron, reflective type fixed on existing glass panels complete all as specified and as directed.

Removing excavated soil, debrises obtained from demolition from various locations (other than this work) from site to outside MOD land complete all as as directed. The location at out side MOD land for disposal shall be located by the contractor himself).

S & F 18 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work fitting of shutters as approved by GE shall be fixed suitable for cup board etc. including taking down with existing one complete all as specified and directed.

S & F 12 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work fitting of shutters as approved by GE shall be fixed suitable for cup board etc. including taking down with existing one complete all as specified and directed.

S & F Stainless steel W hinges ISI marked 75 x 18 x 18mm, to cupboards complete all as specified & directed.

S&F 6mm thick Teak wood lipping for plywood cupboard of 12mm thick shutters complete all as specified and as directed

S&F 6mm thick Teak wood lipping for plywood cupboard of 18mm thick shutters complete all as specified & directed.

S&F 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified & directed.

S&F in repairs 110mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors complete all as specified & directed.

S&F in repairs 75mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors complete all as specified and as directed

S&F in repairs 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls complete all as specified and as directed

S&F in repairs 75mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls complete all as specified and as directed

S&F in repairs 50mm bore PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to walls complete all as specified and as directed

in repairs PVC (SWR) bends of any radius of 110mm bore complete all as specified and as directed

S&F in repairs PVC (SWR) bends of any radius of 75mm bore complete all as specified and as directed

S&F in repairs PVC (SWR) bends of any radius of 50mm bore complete all as specified and as directed

S&F in repair for PVC (SWR) branch piece, single Y, equal or unequal for 110mm bore pipe complete all as specified and as directed.

S&F in repair for PVC (SWR) branch piece, single Y, equal or unequal for 75mm bore pipe complete all as specified and as directed.

S&F in repair for PVC (SWR) junction single (single 'T') equal or unequal for 110 mm bore pipes with access door complete all as specified and as directed.

S&F in repair for PVC (SWR) junction single (single 'T') equal or unequal for 75mm bore pipes with access door complete all as specified and as directed.

M&L for coloured, textured design heavy duty exterior tiles of size 300mm x 300mm x10 mm thick as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and shade/ pattern as approved by GE over and including 15mm thick screed bed in CM (1:4) and demolition of existing tiles of any description complete all as specified and as directed. Make: Johnsun Endura textured design or equivalent of Kajaria/ Somani as approved by GE.

M&L for designer coloured glossy rubber moulded chequered cement concrete tiles of size 30cmx30cmx25 to 27mm thick in floor, set, jointed and pointed in neat cement slurry with grey cement and pigment over and including 20mm thick screed bed in CM (1:6) including dismantling of existing tiles of any description laid in cement mortar complete all as specified and as directed.

M&L for machine pressed precast cement concrete coloured interlocking paver blocks, glossy rubber moulded, of triangular / Zigzag / Haxagone/any shape/design and size as approved, 60mm thick, conforming to IS 15658-2006, M-35 with grey cement and pigments grade in floor/ paths/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including filling the joints with sand including dismantling of existing tiles of any description complete all as specified and as directed. NOTE: (i) Manufacturers test certificate shall be submitted alongwith sample.

Dismantling existing interlocking paver blocks, removing rubbish off the premises and laying the same tiles/ blocks on existing places with repair of existing PCC for 60mm thick tile, in floor/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile complete all as specified and as directed.

S&F in repairs plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated hinging device for pedestal pattern WC/ semi pedestal pattern WC (anglo India type) complete all as specified and as directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded broken stone aggregate) as in fdns, filling, sub base and mass concrete etc. incl dismantling existing concrete complete all as specified and as directed.

M&L in repair for 2nd class HW plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc 3 and n.exc 6 sq.cm incl two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for running welding in repairs for metal to be welded not exc. 6mm thick complete all as specified and as directed.

M&L for running welding in repairs for metal to be welded exc. 6mm not exc. 9mm thick complete all as specified and as directed.

M&L for welding in repairs n. exc 2.5cm in length and thickness of metal to be welded not exc. 6mm complete all as specified and as directed.

M&L for welding in repairs n. exc 2.5cm in length and thickness of metal to be welded exc. 6mm but n exc 9mm complete all as specified and as directed.

Each leaf