8870 SPECIAL REPAIRS TO BLDG NO P-2 OFFICER MESS REAR PORTION AT COD MALAD COMPLEX UNDER GE NORTH MUMBAI

Amount

Civil works Disconnecting of PVC water storage tank of capacity exc 500 ltrs and n exc 1000 ltrs setting aside for repairs Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc.complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete for old water proofing treatment of any description and in any position, not otherwise specifically provided for, any thickness, above ground floor including removing debris out side MD land complete all as specified and directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., applying neat cement slurry @ 3kg of cement per square metre complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40mm thick (average thickness) PCC (1:2:4), type B1, using 20mm graded stone aggregate as levelling course, laid to slope as required and finishing even & fair without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for 10mm thick rendering with cement mortar 1:3 on roof slab/canopies/chajjas with water proofing compound at 3% weight of the cement as per manufacture instructions and make surfaces to receive water proofing treatment finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note : Water proofing compound will be measured and paid separately

Material and labour preparation of surfaces by removing bitumen based water proofing treatment completely removed by mechanical scarification or by any other effective mechanical means and prepare the normal surface thoroughly by cleaning , washing and removing dust, dirt oil, grease, any loose particles etc and applying one coat of Dr FIXIT prime seal diluted with water in the ratio 2:1 and dry minimum 2-3 hours and apply Dr FIXIT new coat in three coats at the rate 0.50 litre per sqm in each coat and dry 6 to 8 hrs after each coat with and including laying woven glass fibre mesh 2-5 mm x 2.5mm between first coat and second coat complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for applying two coats of flexible polymer acrylic water proofing coating, 1mm thick (Dry film in two coats) using Dr Fixit pidifin 2K of M/S Pidilite Industries or equivalent including necessary pond testing in sunken portion complete all as specified and directed by Engineer-in-Charge.

Supply and fix 32mm GI pipe medium grade as in spout n.exc 1.00 Rm each (in short length) complete all as specified and as directed by Engineer-in-Charge. Make: Tata/Jindal/Zenith/Swastik/Prakash

Material and labour for Plain cement concrete 1:5:10 Nominal mix type E2 using 40mm graded stone aggregate as in sunken floor complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work/stone/PCC block masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class "B" bricks straight or curved on plan exceeding 6 mtr mean radius with old size bricks and built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-Charge

Material and labour for brick work built in cement mortar 1:4 using sub class 'B' bricks, straight or curved on plan to any radius as in half brick thick wall all as specified and as directed.

Material and labour for surface preparation of structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer-in-charge (including removal of external plaster, wherever exists) costs inclusive of transportation, labour, conveying debris away from the site (max 50m) tools and tackles, lead and lift etc, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix CRS (Corrosion resistant steel), 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Supply and fix CRS (Corrosion resistant steel), 8 to 10mm dia in stirrups, spacers and binder cut to length bent to shape required inch cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Demolition of reinforced cement concrete of any description in any position including necessary scaffolding arrangement (reinforcement cut as required to facitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. Note : Reinforcement obtained from this item shall be handed over to contractor on account of sch of credit

Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour and but excludes the materials for grouting the pins.etc complete all as specified and as directed by Engineer-in-Charge.

Repairing of excessively damaged concrete portion by using superfluid dual shrinkage compacted and providing, casting with micro concrete of grade M-30 at all levels with all leads and lift as directed including mixing, laying, levelling, finishing including curing and formwork of steel or marine ply complete all as specified and directed by Engineer-in-Charge. Note: Grade of Micro-concrete to be M 30 at 28 days and shall be sourced from manufacturer's such as Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved .

Material and labour for formwork of to pour the micro concrete/concrete using steel shutters or 12mm marine ply to have the form finish including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour Reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies etc. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and applying rust cleaner (Re-backler solution) to exposed corroded reinforcement @ 0.20 Litre/Sq or approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc. complete as directed by Engineer-In-Charge.

Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB or equivalent of approved make and quality comprises of resin and hardener mixed in equal proportion by volume with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. NOTE:- New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be inclusive in this item of work.

Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforms to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method by mixing Base and curing agent in 2:1 proportion by weight for joining old and new concrete as per technical specifications of manufacturer. Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge

Material and labour for providing and laying 20 mm thick POLYMER MODIFIED MORTER over identified R.C.C. members in One layer in proportion of 1:5:15 by weight of polymer of approved make, cement and filler material of approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for removing loose disturbed & disintegrated concrete surface of RCC beams , columns , chajjas, lintel, ceiling etc and cleaning exposed rusted reinforcement , removing rusted scales by chipping and cleaning by wire brushes and applying anticorrosive epoxy coating as per manufacturer's instructions on prepared surface to receive gunniting including necessary scaffolding and preparing to support the damaged structural members, supplying & tying welded wire mesh 100 mm x 100 mm x 10mm dia, binding with GI wire 22 gauge to reinforcement , applying cement slurry uniformly to exposed surfaces and gunniting using CM 1:3, average thickness of gunniting not less than 40mm and finishing the surfaces with 10mm thick rendering in CM 1:4, troweled even & smooth finish, without using extra cement & removing debris out side MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour Drilling and fixing teflon nozzles in RCC members, including drilling holes (drilling 12 mm dia, 40mm deep holes in structural members at the intervals of 600mm c/c in staggered manner or s directed by Engineer-in Charge in RCC structure elements and cleaning the holes (to clean the holes by air blower prior to fixing nozzles) and fixing of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles to be machined to receive outlet of grouting gun and fixing it inside the holes by applying thixotropic epoxy putty to ensure complete sealing and curing the system for minimum 12 hrs) and cutting of nozzles (to cut the nozzle by chisel after completion of grouting without damaging structural elements etc complete all as specified and as directed by Engineer-in-Charge.

Injecting low viscosity (3-5 cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuses to accept the grout, Including, Mixing of materials( Mixing material components (part a & b) in required quantities as per manufacturer’s instruction by weigh batching) and Grouting ( Filling the grouting gun with monomer. Maintain desired pressure in the gun by air compressor; maintain the pressure at exit (4 to 5 Kg/ Cm2) by monitoring pressure gauge at exit. Grouting the material through prefixed nozzles in the structural elements till its refusal. Sealing the nozzle with epoxy putty after the refusal. Monitoring leakages through other nozzles while grouting and seal them as per the requirement. Repeat the process for all the nozzles. the operation to be within pot life of the material.)and Cleaning of gun and accessories ( the gun and accessories like valves, pipes and other fixtures to be cleaned with thinner after the operation to avoid jamming of the gun.) etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Strengthening structural elements with non metallic composite fiber wrapping system comprise of uni-directional carbon fiber sheet (430 GSM) and compatible saturate Profiling, applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixotropic epoxy putty etc. , complete mechanized wetting of fiber sheet, cutting the fabric to required size, mixing of saturate and filling in tub area of the saturation machine, placing the fiber on metallic rods and pass through the rollers of machine and saturate tub ensuring complete wetting (65% fiber volume fraction) of fibers, removing the fiber on rod and placing the new fiber sheet, wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc., repeating the same procedure for multiple layer with the interval of 8 hrs ,applying second coat of saturate after minimum 12 hrs after first coat, rectify air voids if any and finally rendering with10mm thick in CM 1:6 including finishing even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Mode of measurement- Per sq.mt of surface area of carbon fiber sheet without lapping. Make- FOSROC/FIXIT/Krishna Conchem/ Sika

Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50X55 system, spreading the anchor fibers in star pattern including application of saturate complete all as specified and as directed by Engineer-in-Charge. Note for Item No.18 to 30:- (i) The work under Item No. 10 to 15 shall be carried out by authorised applicator only. (ii) Defect liability for these items shall be 5 years from certified date of completion. (iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above.

Taking down cement plaster on brick or stone walls including ceilings etc., including racking out joints, hacking for key scrubbing down with water all as directed.

Material and labour for rendering 10mm thick on internal wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Soundplast PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:6 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over masonry and concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

All as per item No.32 but of 5mm rendering of minimum composition of C:S 1:4 on ceiling and finishing surfaces complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 15 mm thick cement plaster in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix' of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S :1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound @ 3% by weight of cement or as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrink-free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over 1.5mm wall care putty on wall complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of new plastered surfaces of wall , and applying two coat of plastic emulsion paint over a coat of priming paints over thin layer of wall care putty on wall complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints/ Shalimar Paints

Material and labour for preparation of new plastered surfaces on ceiling and applying two coats of Distemper oil emulsion over a coat of priming plastered and other surfaces with alkali resistant priming paint over thin layer of wall care putty on ceiling complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing new plastered surfaces and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of acrylic primer over a thin layer of wall care putty on wall surfaces complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over 1.5mm wall care putty including preparation complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of old painted surfaces of wall , and applying two coat of plastic emulsion paint over a coat of priming paints over thin layer of wall care putty on wall complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints/ Shalimar Paints

Material and labour for complete removal of existing treatment on wall and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for preparing old wooden surfaces of any description, over 10 cm width or girth, and applying one coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints/Nerolac Paints/Berger Paints/Shalimar Paints

Material and labour for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Taking down chowkats or frame with shutters, not exceeding 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Taking down chowkats or frame with shutters, exceeding 1.5 sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6Nos screws to be provided for each frame all as specified and as directed. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and as directed.

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing surfaces of wood and wood based materials, steel and iron work, treating ends of posts, hold fasts, backs of chowkats, etc., area tarred exceeding 0.1sqm not exceeding 0.5 sqm each and treated with tar or coal tar black paint complete all as specified and as directed by Engineer-in-Charge.

Supply and fix mild steel hold fast confirming to Fe 290 grade E-165 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Plain cement concrete type C1 1:3:6 (20mm graded aggregate) for fixing hold fasts/ refilling in floor cutting with necessary plaster complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 35mm thick factory made plain framed panelled shutter 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 30mm thick "RAJSHRI" brand factory made wire mesh solid pvc door shutter consisting of frame made out M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for 15mm x 15mm for top, lock & bottom rails, M.S. frame shall have a coat of metal primer of approved make and manufacturer. 19mm x 19mm M.S. square tubes shall be covered with heat moulded plain sheet ' C' channel made from 5mm plus minus 0.25 mm thick PC sheet of Density 600 Kg/ cbm Manufactured by an ISO -9001-2015 certified company, of size 30mm thickness, 90mm width out of which 75mm shall be flat and 15mm shall be bent in 90 degree angle on either side forming stiles, one of the 90 degree bend edge is cut from stiles as well as rails to nail from inner side of door to hide wire mesh fixing steel screws, 5mm plus minus 0.25 thick 115 mm wide PVC sheet out of which 100 mm shall be flat and 15mm shall be bent in 90 degree on the inner side to form top and bottom rail and 130 mm wide PVC sheet out of which 100 mm shall be flat and 15mm shall be bent in 90 degree on both side to form lock rail. An additional 5mm plus minus0.25 mm thick PVC strip of 20mm width is to be stuck on the interior side of the C channel using PVC solvent cement adhesive. Panel will be of aluminium wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wire mesh in top, bottom, rock rail is sealed with 15mm x 15mm tube with steel screw of size 13/6 mm 10mm (5mm x 2nos) thick PVC strip of 25mm width is to be stuck & nails on both side of G.I. wire mesh interior at the top , bottom, rock rail. 10mm thick (5mm x 2 nos ) thick , 20mm wide cross PVC sheet as gap insert for top rail & bottom rail door to be fixed to frame with 3 nos M.S powder coated butt hinges size 100mm x 25mmx 2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S. tube other hardwares should be fixed with 19x6mm size steel screws etc complete as per direction of Engineer-in-Charge, manufacturer's & drawings.

Supply and fixing 30mm thick " RAJSHRI FACTORY MADE PVC CUP BOARD SHUTTER- WOOD FREE consisting of frame made out of MS tubes of 19 gauge thickness and size of 20mm x20mm for stiles as well as top bottom and lock rail. The inside panel shall consist of 20mm thick multi champer hollow PVC section of 1 mm wall thickness bonded using solvent cement adhesive with 5mm (plus or Minus) thick One side Prelam and other side plain colour PVC sheet of Density 600 kg/Cbm manufactured by an ISO - 9000 certified company on both side of the inside panel. the four edge of the panel to be sealed with lapping of 10mm thick & 20 mm wide PVC sheet batten(made by sticking 2 Nos rigid foam PVC sheets of 5mm plus or Minus) thickness PVC solvent cement adhesive 20mm thick (5mm x 4 Nos). Thick PVC sheet to be given for lock provision at lock height. complete as per direction of Engineer-in- Charge. manufacturer's specification and drawing. Frame including size of 60x50 mm excluding handle 150mm size, Hinges stainless steel (Heavy) 100mm size, cupboard lock godrej or equivalent and screw and wall plug complete all as specified and as directed by Engineer-in-Charge.

Supply and fix RAJSHRI PLASTIWOOD 18mm thick Plain PVC Ply fixed with screw/bonded with PVC adhesive solvent complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 150mm long brass handles cast type polished bright complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix floor door stopper of stainless steel 150mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix 32mm Pin cylinder wardrobe lock of Godrej make Code No 7030 complete all as specified and as directed by Engineer-in-Charge.

Supply and fix stainless steel butt hinges, medium weight, 150mm size all as specified and directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy 250mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 140mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix 15 micron coloured aluminium sections for sliding or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix in repairs 15 micron coloured aluminium anodised grill of design No DG-101, 10 mm thick, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLE of Associated group or equivalent make as approved by GE

Supply and fix in repair Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge Make : Classic/ Shalimar/ CLIF/ARGET

Taking down aluminium window shutter carefully from aluminium sliding frame, n.exc 1 sqm each and refixing in same position after replacing the window glass pane, wire mesh and nylon roller, rubber beading etc complete all as specified and as directed by Engineer-in-Charge. Note: Glass pane and wiremesh will be measured and paid separately under respective item as "Supply only"

Taking down aluminium door shutter carefully, area exc 1.sqm but not exc. 2sqm each and refixing in same position after repair/replacement of handle, floor door stopper, glass, rubber etc complete all as directed. Note :- Only Glass will be measured and paid for separately as "Supply only"

Supply only 5.5mm thick black tinted glass, in square exc 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Taking down chowkats or frames with shutter (without taking off shutter from shutter ) exc 1.5 sqm but n.exc 4 sqm each including fittings & refixing in the same opening complete all as specified and as directed by Engineer-in-Charge

Taking down chowkats or frames with shutter (without taking off shutter from shutter ) n exc 1.5 sqm each including fittings & refixing in the same opening complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs stainless steel curtain rod , 25mm dia complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair Fancy type bracket suitable for curtain rod 25mm dia complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete / cement lime concrete / mud faska (unreinforced in roof and terrace other than ground floor) any description alongwith existing chequered tiles and removal of rubbish to outside MD land etc complete all as specified and as per directed

Material and labour for 75mm thick PCC (1:4:8) type D2, (using 40mm graded stone aggregate) as in sub base, finished even and rough complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick Plain Cement Concrete (1:3:6) type C2, nominal mix (using 40mm graded stone aggregate) as in plinth protection & finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for light shade vitrified ceramic tiles of size 600 x 600x 10mm thick in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles including screed bed 15mm thick in cement mortar (1:6) etc complete all as specified and as directed. Make : Johnson Marbonite/Kajaria/Somany/Euro tiles

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles not exc exceeding 0.36 Sqm (including 600mmx600mm size), on vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge Make : Johnson Marbonite/Kajaria/Somany/Euro tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engineer-in-Charge. Make : Johnson tiles/Kajaria/Somany/Nitco tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in colour cement to match including backing coat 10 mm in CM (1:3) complete all as specified and as directed by Engineer-in-Charge. Make : Johnson tiles/Kajaria/Somany/Nitco tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors and jointed in neat cement slurry and pointed in colour cement to match including backing coat 15 mm in CM (1:6) complete all as specified and as directed by Engineer-in-Charge. Make : Johnson tiles/Kajaria/Somany/Nitco tiles

Material and labour for joint free, coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm , on vertical surfaces etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including cement plaster 10mm thick in CM (1:4) complete all as specified and as directed by Engineer-in-Charge. Make : Johnson tiles/Kajaria/Somany/Nitco tiles

Material and labour for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry as in skirting/dado and pointed with white cement with admixture of pigment to match the shade of granite tiles including grinding and polishing including 15mm thick backing coat in cement mortar (1:4) all as specified and as directed.

Material and labour 18 to 20 mm thick machine cut , grinded and polished, mushroom granite stone, bedded and jointed as in steps, jambs, pillar, window cills, cooking platform and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match complete all as specified and as directed by Engineer-in-Charge.

Material and labour machine pressed precast concrete interlocking paver block of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment with glossy finish including 25mm sand cushioning complete all as specified and as directed by Engineer-in-Charge. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

Material and labour for factory made, Precast, cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate in kerb stone of size 300mm x 400 x 100mm in required shape finished smooth, set in cement mortar 1:4 including excavation earth work in any type of soil complete all as specified and as directed by Engineer-in-Charge. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

Taking up or down 15mm bore steel tubing and connections, complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, complete all as specified and directed by Engineer-in-Charge.

Taking up or down 25mm bore steel tubing and connections, complete all as specified and directed by Engineer-in-Charge.

Supply and fix 40mm outer dia, three layer PP-R polypropylene random copolymer concealed pipes SDR- 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or in floors complete all as specified and directed by Engineer-in-Charge. Make : Prince/Finolex/Supreme

Ditto as item No 97 above but 32mm dia complete all as specified and directed by Engineer-in-Charge.

Ditto as item No 97 above but 25mm dia complete all as specified and directed by Engineer-in-Charge.

Ditto as item No 97 above but 20mm dia complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

Supply and fix in repairs concealed type stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Soma/Leader/Zoloto/Prayag

Supply only 15mm bore CP pillar taps, fancy type, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'hot or cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed by Engineer-in-Charge. Make : Jaguar/Soma/Leader/Zoloto/Prayag

Supply and fix in repair Jet spray (Butterfly) with 1Mtr tube Cat No-BEA-17 of Make-Prayag or equivalent as approved by GE) complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair health faucet (body cleaner) with 1.0m tube and hook (PVC tube), white/Ivory Cat No- BEA-84, Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair corner glass shelf 300mm Cat No- BEA-44 of Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair, glass shelf 300mm (with ABS Brackets) Cat No- BEA-49 of Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair Peg set 6 Cat No- BEA-30 (of Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair CP brass towel Rack Cat No- BA-52 of Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair CP brass soap Dish Cat No- BA-15 of Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair CP brass towel Ring Cat No- BA-21 of Make-Prayag or equivalent as approved by GE complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs Stainless steel sink with drainage board 1.00 mm thick (AISI 304 quality), glossy finish, for kitchen or laboratory with plugs, waste pipe, washers, including bedding in cement mortar to dwarf walls or including fixing cantilever cast iron brackets, connecting union etc., overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, with flush pipe, complete all as specified and as directed by Engineer-in-Charge. Make : Diamond/Nirali/Neelkant/Bluestar/Prayag NOTE- In case non availability of given size, the nearest next size shall be used without any extra cost.

Supply and fix in repairs tubular towel rail brass chromium plated 20mm dia, 'D' type, 60cms long between flanges fixed to walls with screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs Swivel shower of PTMT, any colour, for fixing with 15mm pipe, minimum weight 40gms complete all as specified and as directed by Engineer-in-Charge. Make : RS Industries or equivalent make as approved by GE

Supply and fix in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm), including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) & provision of Plain cement concrete 1:5:10 nominal mix type E2 using 40mm stone aggregate all as specified and as directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets and connection to pipes and fixing of chain and pull or lever complete all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm excluding taps, waste chain and plug and porcelain stopper including brackets,chromium plated waste coupling, waste fitting etc, cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete as specified and directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson Note:- Pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately as "Supply only

Supply only 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engineer-in-Charge. Make : Soma/Leader/Zoloto/Prayag

Supply only PVC connection,15 mm size with PTMT nuts, of length 450 mm complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply only PVC waste pipe 32mm bore of size 450mm to 600mm long complete all as specified and as directed by Engineer-in-Charge.

Dismantling of 110mm cast iron/PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Dismantling of 75mm cast iron/PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Supply and fix UPVC (SWR) single socketed rain water/soil waste pipes, type B, with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) bends any radius, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) branch piece Single Y equal or unequal, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) branch piece double Y equal or unequal, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) branch piece single T equal or unequal, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) single socketed rain water/soil waste pipes, type B, with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) bends any radius, 75 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Material and labour in repair for anodised aluminium snap grid frame work for false ceiling conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, 4 mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm , cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system including 10mm thick PVC insulation panel with EPS stuck to 1mm plain PVC sheet with all connecting accessories suitably placed in false ceiling grid as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: Gypsum board /Arm Strong/Ramco/Bisan

Supply and fix in repairs UPVC floor trap 63mm outer dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc, complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix in repair UPVC (SWR) Vent cowl any radius,110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix in repair PTMT grating doom over Nahani trap and floor trap of 100mm Dia complete all as specified and directed by Engineer-in-Charge. Make : RS Industries or equivalent make as approved by GE

Material and labour for Rolled mild steel sections as in joist, channel, angle, or tee sections, without connecting plates, etc to form frame complete all as specified and conforming to Fe - 410 W (Grade E-250) 'A' quality complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make : METCO Roof Pvt Ltd/ as approved by GE

Material and labour for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer with necessary scaffolding / shuttering etc complete all as specified and as directed. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Supply and fix in repair rotational moulded polyethylene water storage tanks 1000 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex/Polycon/infra/Rotex

Supply and fix in repair rotational moulded polyethylene water storage tanks 500 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex/Polycon/infra/Rotex

Excavation in trenches n.exc 1.5 m wide and n. exc 1.5 m in depth and getting out in Soft/loose soil for exposing of pipe etc complete all as specified and as directed by Engineer-in-charge.

Returning, filling in including spreading, leveling, watering and well ramming soil in layers n.exc 25 cm thick complete all as specified and as directed by the Engineer-in-Charge

Removing excavated soil to a distance exceeding 1.5 Km but not exceeding 5 Km and depositing where directed outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour reinforced concrete pipes 150mm bore, class NP-2, laid and jointed in CM (1:2) with spun yarn complete with collars all as specified and as directed by Engineer-in-Charge. Make : Indian hume pipes/Everest/Himalaya/Thuluvananikal Pipes

Material and labour Plain cement concrete 1:2:4 type B-2 Nominal mix (using 40mm graded stone aggregate) as in foundation filling and mass concrete finishing the surface even and smooth without using extra cement as in flooring complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Providing, cement concrete type B1 1:2:4 (using graded stone aggregates 20 mm) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, if directed including necessary form work complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Plain Cement Concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in benching of manhole , surface channels & drain including necessary form work for fair finished surfaces complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, bore of pipe 150mm dia,complete all as specified and as directed by Engineer-in-Charge.

Extra for forming fair finished drain or channel, not exc 30 cm inner girth in cement concrete , using extra cement, including forms, moulds, mitred /stopped ends etc complete all as specified and as directed by Engineer-in-Charge.(Inner girth only will be measured)

Material and labour for providing precast reinforced cement concrete, 1:2:4, type B-1 (using 20 mm graded stone aggregate) for manhole / drain covers etc., set in cement morter 1:6 and finishing the exposed faces even and smooth without using extra cement including demolition of existing unserviceable RCC covers and removing debris out side MD land complete all as specified and as directed by Engineer-in-Charge. Note :- Reinforcement shall be measured and paid separately).

Material and labour for cutting into existing manholes for 150/200mm internal dia of pipes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B1, smooth finished and reforming benching as required complete all as specified and as directed by Engineer-in-Charge.

E/M Works Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials out side MD land in case of Credit and making good disturbed surfaces of walls, floors, etc., all as specified and as directed.

Material and labour for Point wiring complete with PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor conforming to IS-694, 1.5sqmm (nominal area) drawn through and including non metallic rigid PVC casing / capping (ISI marked, not lessthan 20mm wide) and accessories on surface of wall/roof with sunken type pressed steel/welded terminal boxes made out of 1.6mm mild steel sheet, 3mm thick laminated sheet cover for mounting of switches, socket outlets, regulators etc., including provision of PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor 1.5sqmm as earth continuity conductor and connecting to common earth dolly complete all as specified and as directed for the following: Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG

One light/fan/bell point controlled by one, one way switch

One 3 pin 5 Amps switch socket point on independent board.

One 3 pin 5 Amps socket outlet independent but below the switch board of light points in the same vertical plane

One light point controlled by two way switch

All as per item No. 153 described here - in - before but for 3 pin 15 Amps switch socket on independent board with 2.5sqmm copper cable and provision of 2.5sqmm PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor for earth continuity conductor connected to common earth dolly connecting up to fittings complete.

Supply and fix Switch Piano, flush type, single pole, one way, 6 Amps, 240 volts, ISI marked complete all as specified and as directed. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Switch Piano, flush type, single pole, two way, 6 Amps, 240 volts, ISI marked complete all as specified and as directed. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Ceiling rose, surface type Bakelite, three terminal 65x32mm, ISI marked complete all as specified and as directed. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix switch socket combination 2 in 1 flush type 5 Amps multipurpose complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Crabtree/Leader/Legrand/Havells

Supply and fix switch socket combination 2 in 1 flush type 15 Amps 3/5 pin complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Crabtree/Leader/Legrand/Havells

Supply and fix ceiling fan regulator AC, 230 volts electronic step type complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Crabtree/Leader/Legrand/Havells

Supply and fix electric call bell AC 230v single pole complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Crabtree/Leader/Legrand/Havells

Supply and fix bell push AC 230volt 5 amp flush type complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Crabtree/Leader/Legrand/Havells

Supply and fix in repairs double door, sheet metal enclosure powder coated MCB DB SPN 8 way with 200 Amps rated bus bar, 240 volt,IP 42 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs double door, sheet metal enclosure powder coated MCB DB SPN 4 way with 200 Amps rated bus bar, 240 volt,IP 42 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs double door, sheet metal enclosure powder coated MCCB DB TPN 12 way vertical type with neutral link earth bar din rail with 200 Amps rated bus bar, 415 volt,confirming to IS 13032-1991 including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells Note : for Main incomer of Main DB and MS pedestal panel incomer control

Supply and fix in repairs MCCB 4 pole, 415 volts, fixed type, 100 Amps with breaking capacity 25 KA including all connections and testing complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix change over switch TPN 63A 440V panel mounting type with all necessary connecting accessories complete all as specified and directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

S& F in repairs MCB TPN,63amps, 415 volts,25 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs double door, sheet metal enclosure powder coated MCB DB TPN 4 way with 200 Amps rated bus bar, 240 volt, IP 42 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

S& F MCB SPN,6 to 32amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

S& F MCB SP 6 to 32amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs LED tube light fitting 1 X 18 Watts, 230 volts, all pre wired fixed on walls with all fixing accessories such as 2 Nos of PVC square/round box, screws etc and connecting up three core flexible copper conductor cable of size 24/0.20 sqmm including LED tube rod complete all as specified and as directed by Engineer-in-Charge. Make:- Bajaj LED tube light Cat Part No BLRB 18W CW or equivalent in Wipro/CG/Havells Make:- Bajaj Batten Cat Part No BLRB DB 118 or equivalent in Wipro/CG/Havells

Supply and fix in repair LED tube light fitting, 1 X 10 Watts, 230 volts, with long lasting PVC body with slim and sleek looks all pre wired fixed on walls with all fixing accessories such as 2 Nos of PVC square/round box, screws etc and connecting up three core flexible copper conductor cable of size 24/0.20 sqmm, including 10w tube rod complete all as specified and as directed by Engineer-in-Charge. Make:-Philips/ Havells/CG/ Bajaj

Supply fixing and connecting from existing ceiling rose with 3 core flexible copper wire of required length 2' x 2' LED 42w recess softline luminaire suitable for armstrong/grid ceiling with high brightness LEDs and PMMA extruded diffuser given glare free light and good aesthestic appeal,complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat part No VENUSNEOHE2X2PLR42WLED8XXS or Equivalent make of CG/Philips/Bajaj

Supply fixing and connecting from existing ceiling rose with 3 core flexible copper wire of required length 1' x 1' LED 15w recess softline luminaire suitable for armstrong/grid ceiling with high brightness LEDs and PMMA extruded diffuser given glare free light and good aesthestic appeal,complete all as specified and directed by Engineer-in-Charge. Make:-Philips/ Havells/CG/ Bajaj

Supply and fix LED bulb 09 watt of any type complete all as specified and as directed by Engineer-in-Charge. Make: Bajaj / CG/Wipro/Surya/Philips

Material and labour for Submain wiring complete with and including 2 runs of 6.0sqmm, single core FRLS, PVC insulated and unsheathed, multistranded, copper conductor cable, single core, 1100 Volts grade drawn through and including PVC conduit, medium grade of size 20mm including accessories such as Tees, Elbows, junction box, reducers etc as required and fixed on walls and 4.0 sqmm PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG Note :- (i) Two runs of 6.0 sqmm PVC insulated cable and one run of 4.0 sqmm cable and one run of PVC conduit shall be measured as one unit length.

Material and labour for Submain wiring complete with and including 2 runs of 4.0sqmm, single core FRLS, PVC insulated and unsheathed, multistranded, copper conductor cable, single core, 1100 Volts grade drawn through and including PVC conduit, medium grade of size 25mm including accessories such as Tees, Elbows, junction box, reducers etc as required and fixed on walls and 2.5 sqmm PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG Note :- (i) Two runs of 4.0 sqmm PVC insulated cable and one run of 2.5 sqmm cable and one run of PVC conduit shall be measured as one unit length.

Supply, install, test and commision LED street light fitting 1 x 45 watts,pressure die cast aluminium housing, Heat resistance toughened glass with frame, IP 66 protection, better optics for uniform distribution complete with necessary copper wire connection of suitable size complete all as specified and as directed by Engineer-in-Charge. Make - Bajaj Cat Part No BRTFG 45W LED or Equivalent in CG/ Philips/Havells/Halonix

Supply and fix mild steel box pedestal type (floor mounting) with replacement of new DBs and MCBs made out from 3mm thick CRCA sheet duly painted with two coats of synthetic enamel paint over red oxide primer of size 1.2m x 1.2m x 0.40m including rear side closed and fixed in angle iron stand 40mm x 40mm x 5mm grouted in floor including 45cm height from floor level and refixing of existing change over & new DBs and MCBs including providing wiring of suitable size of copper conductor cable and including necessary masonry work with water proof plywood/wooden planks for mounting DBs and MCBs including taking down of existing unserviceble wall mounted DBs existing electrical accessories and making good the surface complete all as specified and as directed by Engineer-in-Charge. Note : DBs and MCBs and connecting accessories are measured and paid separately on respective item

Material and labour Hot dip galvanised 2mm thick perforated GI cable tray size 200mm x 50mm upto 2.50m long including all fixing accessories such as 3mm thick side coupler plates ( 4 nos holes & 4 slots), M8 x 25mm long GI bolts with 2 nos plain washers and 1 No spring washer for coupler plate complete all as specified and directed by Engineer-in-Charge.

Material and labour Earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to and including galvanised earth lead wire 6 mm dia, 7.5 m long, by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel with provision of charcoal & common salt packed upto minimum 150 mm all around the earth plate, and protected by 15 mm bore light grade galvanised iron pipe and connected to control board / panel / equipment complete all as shown in electrical plate No.3 of MES schedule Part I with PCC pit in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, MS angle iron frame of size 50mm x 50mm x 5mm, cast iron cover with locking arrangements, GI 20 mm bore medium grade pipe and CI funnel with wire mesh for watering arrangement including necessary excavaion and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge.

Supplying, laying, testing and commissioning of UG round cable of following size, XLPE insulated, heavy duty, LT, 1100 V grade electric cable with aluminium conductor, served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed, as per IS-1554, laid in trenches or passing through pipe, making all connections with necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by Engineer-in-Charge. Make: PARAGON/FINOLEX/PLAZA/POLYCAB/KALINGA/VINAY Note : Earthwork, excavation sand cushioning cable cover GI protection pipe shall be measured and paid separately in their respective items

(a) 95sqmm 3.5 core

(b) 70sqmm 3.5 core

(c) 50sqmm 3.5 core

Removing excavated material to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

Supplying and spreading in trenches fine dry river sand for cable cushioning and gently punning down in layers complete all as specified and as directed by Engineer-in-Charge Note : Thickness of sand cushioning shall be measured after punning and consolidating of sand.

Supplying and laying unreinforced precast concrete cable covers, class LV type, flat of size 250 mm x 150 mm x 40 mm complete all as specified and as directed by Engineer-in-Charge. Make : Mehtab Tiles ,Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles, Jodhpur

Supply and fix GI pipe, light grade, 80mm bore medium grade ISI marked for cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle, wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: TATA/SWASTIK/JINDAL/Bharat Steel tube/ZENITH/Indian Tube Company

Supply and fix GI pipe, light grade, 50mm bore medium grade ISI marked for cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle, wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: TATA/SWASTIK/JINDAL/Bharat Steel tube/ZENITH/Indian Tube Company

Material and labour for cutting the existing bituminous road to size not exc 45cm wide and depth not less than 45cm for passing of UG cable through GI pipe and making good the disturbed surface with C1 1:3:6 concrete using 20mm graded aggregate complete all as specified and directed by Engineer-in-Charge.

Vishal Builders