Renewal of 2 Nos. of 26 Persons bed cum passenger lifts and each 2 Nos. of 10 and 13 Persons passenger lifts at Theni Government Medical College and Hospital in Theni District

Renewal by Design, engineering, supply, fabrication, erection, testing, commissioning and handing over of 26 persons capacity, 1768kg, bed Cum Passenger Lift with M/C room, Speed 1 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller & VVVF drive with enhanced ride comfort and leveling functions, Fire rated doors and ARD, single side entry, gearless Lift as per the relevant IS up to date amendments. (Casualty Block - 1No, 300 Bedded Block - 1No) 1.No. of floors: Ground +3floor, 4 stops 2.Total Travel: 10.8 metres(Apprx.) 3.Levelling Accuracy: High level accuracy with smooth and jerk free stopping. 4.Construction of Car: High quality stainless steel car with Neat hair line finish vinyl floorin and false ceiling . 5Position of machine: Directly above the lift shaft. (Gearless) 6.No. of landing entrance: 4 7.No. of car entrance: one 8.Car entrance door: Power operated V3F drive Centre/Side opening sliding stainless steel scratch proof door with hair line finish. 9. Landing entrance door: Centr opening stainless steel door with hair line finish with provision for emergency key opening at all landings. 10.Lift well existing : 3000mm x 2400mm (As per IS 14665 Part 1 2000) 11. Lift pit depth 1600mm (as ptr IS M665)(part l) - 2000) 12.Car size: 1600mm (width) x 2400mm (Depth) as per IS 14665 (part I) - 2000)/ as per standards upto date. 13.Car clear opening: 1200 mm width x 2000mm height (as per IS 14665) (part l) - 2000) /as per standards upto date.

28.Intercom:To be provided by the lift contractor with in-built intercom (push type) in car panel and with provision of push type intercom in machine room and ground floo entrance. 29.Floor annunciator with music wit announcement in both Tamil and English. 30.Special features: a. Infra-red door sensor with full height c.Voltage stabilizer for circuit control. d.Stainless Steel signal fixtures. e.Vandal proof S.S. Button with S.S. cover f.SS door frames for landing doors. g.VF door operator. h.Call Register signal i.Stainless steel facia plate for car operating panel and landing fixtures. j.On - Off switch for fan and light k.Over load warning indicator awith. audio announcement 31.Other standard features: Over speed governor, phase failure and phase reversal relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joint joist for mounting the machineries. 32.Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm fora period of not less than one year. 33.Site testing in accordance with IS 14665 / standards upto date should be carried out at the time of handing over. 34. Supply of operation and maintenance manual with necessary tools for operation.

35.Lift licence: Preparation of drawing payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor.

Renewal by Design, engineering, supply fabrication, erection, testing, commissioning and handing over of 13 persons capacity 884kg, Passenger Lift with M/C room, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller VVVF drive with enhanced ride comfort and leveling functions, Fire rated doors and ARD, single side entry, gearless Lift as per the relevant IS up to date amendments. (Faculty Block - 2 Nos)

1.No. of floors: Ground +3floor, 4 stops 2.Total Travel: 10.8 metres(Apprx.) 3.Levelling Accuracy: High level accuracy with smooth and jerk free stopping. 4.Construction of Car: High quality stainless steel car with Neat hair line finish vinyl flooring and false ceiling. 5.Position of machine: Directly above the lift shaft. Gearless 6.No. of landing entrance: 4 7.No. of car entrance: one 8.Car entrance door: Power operated V3F frive Centre opening sliding stainless steel ;cratch proof door with hair line finish. 9.Landing entrance door: Centre opening stainless steel door with hair line finish with provision for emergency key opening at all landings. 10.Lift well existing : 2500mm x 1900mm (As IS 14665) (Part 1)- 2000) 11.Lift pit depth 1600mm (as per IS 14665) part l) - 2000) 12.Car size:2000mm (width) x 1100mm (Depth) as per IS 14665 (part l) - 2000)/ as per standards upto date.

27.Automatic Rescue device: To facilitate the landing of the lift to the nearest 'floor' at the of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories. 28.Intercom:To be provided by the lift contractor with in-built intercom (push type) in car panel and with provision of push type intercom in machine room and ground floor entrance. 29.Floor annunciators with music with announcement in both Tamil and English. 30.Special features: a. Infra-red door sensor with 'full 'height screen c.Voltage stabilizer for circuit control. d.Stainless Steel signal fixtures. e.Vandal proof S.S. Button with S.S. cover f.SS door frames for landing doors. g.VF door operator. h.Call Register signal i.Stainless steel facia plate for car operating panel and landing fixtures. j.On - Off switch for fan and light k.Over load warning indicator with audio announcement

31.Other standard features: Over speed governor, phase failure and phase reversa relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side, supporting angles, motor over load protection devices final limit switch main suspension ropes bounter weights lifting joint joist for mounting the machineries. 32.Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period o not less than one year. 33.Site testing in accordance with IS 14665 should be carried out at the time of handing over. 34.Supply of operation and maintenance manual with necessary tools for operation. 35.Lift licence : Preparation of drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor.

Renewal by Design, engineering, supply, fabrication, erection, testing, commissioning and handing over of 10 persons capacity,680kg, Passenger Lift with M/C room, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller & VVVF drive with enhanced ride comfort and leveling functions, Fire rated ft)ors and ARD, single side entry, gearless Lift per the relevant IS up to date amendments. (Casualty Block - 1 No, 300 Bedded Block - 1No)

1.No. of floors: Ground +3floor, 4 stops 2.Total Travel: 10.8 metres(Apprx.) 3.Levelling Accuracy: High level accuracy with smooth and jerk free stopping. 4.Construction of Car: High quality stainless steel car with Neat hair line finish vinyl flooring and false ceiling.

21.Fire Man's switch: To be provided at ground floor. 22.Minor builders work: included in the scope. 23.Scaffolding: Included in the scope 24.Sill angles and facia plates: included in the scope. 25.Steel for lift machinery: Included in the scope. 26.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 27.Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories. 28.Intercom:To be provided by the lift contractor with in-built intercom ( push type) in car panel and with provision of push type intercom in machine room and ground floor entrance. 29.Floor annunciator with music with announcement in both Tamil and English. 30.Special features: a. Infra-red door sensor with full height c.Voltage stabilizer for circuit control. d.Stainless Steel signal fixtures. e.Vandal proof S.S. Button with S.S. cover f.SS door frames for landing doors. g.VF door operator. h.Call Register signal i.Stainless steel facia plate for car operating anel and landing fixtures. j.On - Off switch for fan and light.

k. Over load warning indicator with audio announcement 31.Other standard features: Over speed governor, phase failure and phase reversal relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joint joist for mounting the machineries. 32.Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of not less than one year. 33.Site testing in accordance with IS 14665 should be carried out at the time of handing over. 34. Supply of operation and maintenance manual with necessary tools for operation. 35. Lift licence : Preparation of drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor.

Please Enable Macros to View BoQ information