PROVN OF GUARD ROOM AT MAIN GATE OF FD WKSP COY EME AND SPL REPAIR OF DRAIN (1500 MTR) AND SEWAGE PIPES (2000 MTRS) AT DIGIANA GRM AT MIL STN BD BARI UNDER GE KALUCHAK

Amount

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

Demolition and breaking up drain pipes of any size (salt glazed stoneware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Dismantling of any size cast iron or reinforced concrete drain pipe, jointed in cement mortar, fixed withj wall and taking out of trenches, if required complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and exc. 1.50 m but not exc. 3.00 m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

M&L for earth filling under floor ,spreading and levelling in layers n exc. 25 cm thick well ramming including watering as requiredcomplete all as specified and directed.

M&L for dry sand cushioning for UG cable in trenches including spreading levelling and hand paning and consolidating complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed

M & L for anti-termite treatment by treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of the sub structure in contact with backfill to be measured), complete all as specified & directed.

M & L for anti-termite treatment by treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface(as in under floor or plinth protection/steps/ramps etc), complete all as specified & directed..

M & L for anti-termite treatment by treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified & directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M & L for providing plain cement concrete, type C-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in padding on roof, for levelling of roof slab, finished even and fair, complete all as specified & directed..

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in copings, bed plates, kerbs levelling courses etc, complete all as specified & directed..

M & L for providing pre-cast cement concrete landing, cover slabs, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:4 complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water throughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for providing plain cement concrete type B-0, 1:3:6, (using 12.50 mm graded stone aggregate), as in filling of pressed steel door frames/chowkats complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix),as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate, as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate, as in chajjas and the like complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate, as in columns, pillars, piers, posts, struts and the like complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.

M & L for Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:4 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks (EXCEPT BRICKS) straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. NOTE: - OLD BRICKS OBTAINED FROM DEMOLITION SHALL BE USED UNDER THIS ITEM.

M & L for form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed..

M & L for form work to edges of concrete flats, treads, break in floors, window cills, concrete railings openings in concrete walls, floor and roof and n exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n. exc. 20cm wide for rough finished surfaces of concrete, complete all as specified & directed.

M & L for form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete, complete all as specified & directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in fair finished surface of concrete complete all as specified and directed.

M & L form work to sides of pillars, posts, struts, piers, columns and stanchions in fair finished surface of concrete complete all as specified and directed.

S & F of solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of 35mm thick 2nd class hard wood (Sal/Hollock), glazed and skeleton shutters (factory made), open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I, complete all as specified and directed.

S & F of 35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified & directed.

S & F of 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S & F of 150 mm long anodised aluminium handle, cast type complete all as specified and directed.

S & F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S & F of Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staplescomplete all as specified and directed.

S & F of 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

S & F of 140 mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S&F in repair 25 mm outer dia stainless steel decorative drapery rod (Model No-SS-25FL of Vista) of thickness 20 gauge and for every 01 RM length, provide 10 numbers stainless steel wings(Model NO-SS CRNG of Vista) with 50 mm dia and proportinate for part three off, with stainless steel brackets (Model- SS 25 BR< Vista) near to ends with stainless steel finials (Model SS-1 of Vista with adapter) for 25 mm dia drapery rod at both ends complete all as specified and directed. NOTE:- The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/ windows

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F of Factory made box type steel windows comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube with double side shutters (Wire Gauged shutter and Glazed Shutter), side hung shutters with MS handles and MS stays dovetailed or welded including 02 nos MS Tower Bolt 150mm long for each leaf, 8 mm square guard bars at spacing as shown in drawings, MS flat iron frame work, MS hinges, tarred hold fast, PCC 1:2:4 type B1 as in bed of hold fast, 01 No. per leaf of stopper of 100mm size, one coat of red oxide zinc chrome primer etc, complete all as specified and shown as drawing No. CEPZ/TD-354/09 sheet 1/3 to 3/3. NOTE : a). Wire cloth and Sheet glass shall be measured and paid seprately under respective items. b). Rate of both type of shutters is inclusive in the quoted rate.

S & F steel ventilator with top hung shutter including hinges, steel peg stay, complete including one shop coat of red oxide zinc crome primer, complete all as specified & directed. complete all as specified and directed .

S & F of pressed steel frames of size 125mmx60mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified & directed. NOTE : PCC for filling of hollow portion shall be measured and paid for separately.

M & L for 15 – 18 mm thick machine cut kota stone slab flooring, of size not less than 580x580mm, and 75 mm wide white marble border alround, as per sample kept in GEs office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and polishing to achieve mirror finish laid over and including 15mm screed layer in cement mortar 1:6, complete all as specified.

M & L for 15 – 18 mm thick Machine cut kota stone slab, as per sample kept in GEs office as in vertical surfaces such as skirting/dado etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and polishing, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm thick joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in sub base finished fair complete all as specified and directed.

M & L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. NOTE: - RENDERING SHALL BE MEASURED AND PAID SEPARATELY.

M & L Non - skid joint free ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. NOTE: - SCREED SHALL BE MEASURED AND PAID SEPARATELY.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement)complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extra cement)complete all as specified and directed.

M & L for 5 mm thick rendering on fair faces of brick work or concrete surfaces of ceiling with cement mortar 1:3 finished even and smooth (without using extra cement)complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth without using extra cement using integral water proofing compound as per manufacturer,s instructions , complete all as specified & directed. NOTE:- Integral water proofing compound shall be measured & paid seprately.

Supply only water proofing compound ( (Liquid) complete all as specified.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes finished even and rough complete all as specified and directed.

M & L for 10 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4 on vertical surfaces of wall finished even and rough suitable for laying wall tiles complete all as specified and directed.

S & F of 3 mm thick plain, ordinary quality sheet glass and glazing with oil putty or fixed with beads in square not exc. 0.5 sqm in each pane complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparing newly plastered or previously untreated wall surfaces and applying two coat of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparing newly plastered or previously untreated wall surfaces. and applying two coats of ‘Apex’ of Asian paint or ‘Weather coat’ of Berger Paints over one coat of primer using mechanical vaccume machine complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 100 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 200 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

S & F of 150 mm bore reinforced concrete pipe class NP-2 laid, jointed with collar in neat cement slurry complete all as specified and directed.

M & L for 100 mm dia DWCPE (SN8) HDPE pipes, laid in trenches on PCC bed, jointed as per manufacturers instructions, complete all as specified & directed. Note : Earthwork, PCC bed/ haunching shall be measured and paid for seperately under respective items.

M & L for 150 mm dia DWCPE (SN8) HDPE pipes, laid in trenches on PCC bed, jointed as per manufacturers instructions, complete all as specified & directed. Note : Earthwork, PCC bed/ haunching shall be measured and paid for seperately under respective items.

M & L for 200 mm dia DWCPE (SN8) HDPE pipes, laid in trenches on PCC bed, jointed as per manufacturers instructions, complete all as specified & directed. Note : Earthwork, PCC bed/ haunching shall be measured and paid for seperately under respective items.

S & F of 1000 Litre capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part – I and hoisted, fixed in position complete all as specified and directed.

Cutting existing steel tubing for alterations or additions (Each cut measured) complete all as specified and directed.

Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector)

S&F 15mm nominal bore of pipe in walls, and ceiling or laid in floors, jointing and testing galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all as specified and directed.

S&F 25 mm nominal bore of pipe in walls, and ceiling or laid in floors, jointing and testing galvanised mild steel water tubing “medium grade” with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all as specified and directed.

S&F 15 mm nominal bore of unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all as specified and directed.

S&F 20 mm nominal bore of unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe with and including all fitting (such as bends, elbows, tees, short pieces connectors, back nuts, diminishing pieces, capas, plugs and union etc) complete all as specified and directed.

S&F of bib taps, cast copper alloy with crutch or butterfly handle, screwed down, externally threaded having weight @ 0.40 Kg/Each, ISI marked with IS : 781, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F stop cock (valves), cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, externally threaded, having weight @ 0.40 Kg/Each, ISI certification marked with IS : 881, screwed both ends for iron pipe or for unions of 15mm bore complete all as specified and directed.

S & F in repairs 450 mm long PVC connection with two Nos. PTMT nuts internally threaded and PVC washer suitable for 15 mm bore pipe line complete all as specified and directed.

S & F of 125 mm dia grating doom with waste hole of PTMT (minimum weight 40 gram) complete all as specified and directed.

S & F of chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union size 125 mm complete all as specified and directed.

S & F in repair 20 mm dia brass chromium plated tubular towel rail 'D' type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed.

S & F repair soap dish brass chromium plated, fancy type fixed to wall rawl plugs and chromium plated brass screws complete all as specified and directed.

S & F in repair 20 mm bore gunmetal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F in repair 25 mm bore gunmetal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F of 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shank and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repairs water closet vitreous china squatting pan ‘Orrisa’ pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti-syphonic pipe etc. with and including setting the trap and pan in lime concrete bedding (one lime, two sand or surkhi and 5 aggregate) minimum 150 mm thick alround and finished just below level of rim of pan to receive the floor finishes complete including making good floor complete all as specified and directed.

S & F of vitreous china, wash hand basin, flat back, white of size 580mmx450mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, chain and plug, porcelain stopper including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified & directed

S & F of urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S & F of viterous china urinal, half stall type, white with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, with flush pipe, waste coupling and urinal spreader, fixed in repairs, complete all as specified & directed.

S & F in repair polymer white (polypropylene Delrin and ABS) low level flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, flush pipe, brass screws, handle etc complete having BIS description mark with IS: 7231 with and including 32 mm bore PVC flush pipe of suitable length complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to wall /floor complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) Slotted vent cowl complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to wall complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenchescomplete all as specified and directed.

S & F of 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S & F in repair PVC waste pipe flexible type 32 mm dia suitable for coupling 32 mm 750 mm long complete all as specified and directed.

Desludging / dewatering of septic tanks/ soakage wells including inlet / outlet chambers, removing out all scum, silt, residual sludge (both organic & inorganic in nature) after plugging the incoming sewage lines through combined high pressure water jetting cum suction (Vacuum) type machine mounted on LCV/HCV facility of high pressure vacuum and removing the same in the tank to a place outside cantonment at the place meant for the purpose by local municipality, complete all as specified & directed.

Construction of Septic Tank for 10 users including excavation in any type of soil, foundation in PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) brick work in cement mortar 1:4, RCC (M-25 design Mix) slab including cast iron manhole cover having 6mm plate embedded all around with angle iron frame vent shaft etc, complete all as specified and shown on CE Pathankot Zone TD Drawing No CEPZ/C-TD/013/13 Sheet 1 to 5.

Material & labour for construction of soakage well 1.8 mtr dia and 3.0 mtr deep below inlet (depth) from inlet pipe to ground level 45cm including excavation and earth work in any type of soil, PCC 1:4:8 type D-2 in foundation, wall in honey combed braick work in cement mortar 1:4, earth cushion on brick lining on top, filling with brick bats and inlet pipe 150mm dia complete all as specified and shown on Drg No CE/TD-1202/03 Sheet 1/2 & 2/2.

M&L for preparation of the concrete roof surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying the following roof Treatment complete all as specified & directed :- (a) Applying 1st course of 15mm thick screed bed in cement mortar 1:4 over concrete surfaces. (b) Applying 2nd course of bitumenous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm. (d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm. (f) Applying a coat of bitumious based aluminium

M&L for point wiring one light / fan/ bell/Exhaust fan point controlled by one way switch(concealed type) complete with multi stranded copper conductor flame retardant low smoke (FRLS) 1.5 Sqmm size PVC insulated unsheathed cable 1100 volts grade drawn through with and incl medium grade duty concealed PVC conduit ISI marked not less than 20mm dia including conduit fittings and accessories such as socket,elbow,junction box, bell mouth,bend, reducer etc complete incl cutting chases in existing walls of any description built in cement mortar and making good the disturbed surfaces in cement mortar (1:4) and finishing the surfaces to match with existing surfaces and finish with using sunken type pressed steel terminal boxes of required sizes of not less than 1.6 mm thick factory made and factory painted with top cover of 3 mm thick plastic laminated sheet fixed with brass screws washers with all accessories including single core multi stranded copper conductor 1.5 Sqmm size PVC insulated unsheathed cable green in colour as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified . NOTE :-Wire/Cable colour coding Shall be maintained properly as per IE rule.

All as per item No 117 but for one 3/5 pin socket outlet 5 Amps on the same board with other switches.

All as per item No 117 but for one 3/5 pin 5 Amp socket outlet on independent board.

All as per item No 117 above here in before but with 4.0 Sqmm (nominal area) cable PVC insulated but unsheathed for the 15 Amp 3/5 pin socket power point including 2.5 Sqmm copper conductor green in colour for earth continuity on independent board complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type complete all as specified and directed.

S&F Socket outlet 3 pin, 5A, flush type complete all as specified and directed.

S&F Switch socket combination 2 in 1, 3 pin, 15 Amp flush type universal complete all as specified and directed.

S&F Ceiling rose three teminal /PVC/ polycarbonate, insulated body complete all as specified and directed.

S&F electronic fan regulator, 2 module, 100 watt, (5 stepped type), 240 Volt for 1200/1400 sweep AC ceiling fan complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including one LED retrofit Lamp of B-22 holders base warm white Code No LHLDRUEML8X005 of make Havells or equivalent make of Phillips/Crompton etc complete all as specified and directed.

Supply and fixing factory made epoxy powder coated distribution board, SPN, 12 ways with metal door (IP-43 protection), confirming to IS : 8623 fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall, suitable for universal mounting including 200 Amp copper bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts, suitable for one SPN/DP MCB as incomer and SP MCB outgoing, complete all as specified & directed .

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 63 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified & directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 to 63 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified & directed.

Supply, hanging and testing of BEE 5 Star rated energy efficient brushless direct current motor (BLDC) ceiling fan, 1200mm (48 inch) sweep, having 3 blades made of aluminium alloy, down rod, canopies, shackles, 240 volt, single phase suitable for input voltage range 140-285 volts, AC, 50Hz, power factor not less than 0.99, service value minimum 8 cubic metre / min/ watt or higher, air delivery minimum 230 cu metre/ min or more, power consumption maximum 28 watt or lower, top speed minimum 340 RPM or higher, THD not more than 10% including 5 step electronic regulator marked on rotating knob, two module, 100W, 240 volts with 3 years on site warranty for speed control, copper winding, complete as per IS:374-1979 or latest IE rule & site requirement, colour white complete and taking down old unserviceable fan of any type/ size from existing location and depositing in MES storeyard, complete all as specified & directed.

Supply & fixing metallic exhaust fan, 300mm (12") sweep, single phase, 230 volts, 50 Hz AC, 1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings, complete with louvers and shutters, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable including cutting holes in existing brick walls for making opening for fixing of exhaust fan of 300mm sweep including grounting bolts/nuts ,MS Jali made of 3 mm dia MS wire 50 mm apreature fixed with and including proper wooden frame at outer surface of wall and making good disturbed surface of walls using cement sand mortar 1:4, complete all as specified & directed.

Supply, installation and testing of water heater storage type (Geyser) single phase, 230V, 50Hz, 5 star energy saving, high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion, vertical installation type, 50 Litre capacity, 2000 Watt rated power, incoloy 800 glass coated heating element, tank coating of ferro glass dry powder tank made of ultra thick super cold rolled steel plates, rated pressure 0.8MPa, IPX4 protection consist of safety valves, thermal cut off, thermostat including connecting up fixed to walls by drilling of holes, grouting of bolts of suitable size with nuts etc and making good disturbed surface, complete all as specified & directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 16 Sqmm 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed.

M&L for well burnt brick with sub class ‘B’ old size bricks for protection of cable complete all as specified and directed.

M&L for laying GI tubing light grade 50mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable in trenches complete all as specified and directed.

S&F of Intergral LED security light luminaire 35W LED, 230 volts made up of pressure die cast aluminium housing powder coated with high power SMD LED’s lens & toughned glass IP-66, luminaire, mounted on & including GI bracket made out of 50mm bore medium grade pipe of 1.70m length, bent to required shape, fixed on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer, making connection with PVC copper conductor cable of 1.5 sqmm and taking down old unserviceable light fitting of any type/size, complete all as specified & directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and connecting to main switch or switch board complete and incl PCC masonry pit of 300x300x300mm interior dimensions in PCC 1:2:4 type B-1 RCC cover with GI frame, charcoal and common salt 15cm in layers all round the earth plate, 15mm dia GI watering pipe, a funnel with wire mesh should be provided on top of watering pipe complete all as specified as per electric plate No 3 of SSR 2009 including testing after completion complete all as specified and directed.

M/S Vishwakarma Builders (BID ID -3127158)

M/S SUDAGAR MAL (BID ID -3115763)

M/S VED PAUL MAHAJAN (BID ID -3118787)

M/S ARUN ANAND (BID ID -3115254)