Engineering College

Amount

2.6.1: Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.- All kinds of soil.

2.8.1: Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms , lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m -All kinds of soil.

2.16.2: Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered) - Depth exceeding 1.5m but not exceeding 3m.

2.25: Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

2.26.1: Extra for every additional lift of 1.5m or part thereof in - All kinds of soil.

2.27: Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.

4.1.9: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:4:8 (1 cement:4 fine sand : 8 graded stone aggregate 40mm nominal size).

4.1.10: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1 cement:5coarse sand : 10 graded stone aggregate 40mm nominal size).

4.10: Providing and laying damp - proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

5.1.2: Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement -All work upto plinth level : 1:1.5:3 (1 cement : 1 .5 coarse sand : 3 graded stone aggregate 20mm nominal size)

5.2.2: Reinforced cement concrete work in walls (any thickness)including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.upto floor five level excluding cost of centering, shuttering, finishing and reinforcement:1:1.5:3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 20mm nominal size)

5.2.3: Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centering, shuttering, finishing and reinforcement: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

5.3.1: Reinforced cement concrete work in beams , suspended floors, roofs having slope upto 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

5.8: Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size)

5.9.1: Centring and shuttering including strutting, propping etc. and removal of form for: Foundations , footings, bases of columns, etc. for mass concrete.- Using steel sheet with M.S.frames.

5.9.3: Centring and shuttering including strutting, propping etc. and removal of form for : suspended floors, roofs, landings , balconies and access platform - Using steel sheet with M.S.frames.

5.9.5: Centring and shuttering including strutting, propping etc. and removal of form for: lintels, beams, plinth beams, girders, bressumers and cantilevers.- Using steel sheet with M.S. frames.

5.9.6: Centring and shuttering including strutting, propping etc. and removal of form for: columns, pillars, piers, abutments, posts and struts.- Using steel sheet with M.S.frames

5.9.7: Centring and shuttering including strutting, propping etc. and removal of form for: Stairs (excluding landings) except spiral - staircases - with water proof ply 12mm thick , mango / silver wood scantling and casurina poles

5.9.13: Centring and shuttering including strutting, propping etc. and removal of form for : Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards - Using water proof ply 12mm thick , Mango / silver wood scantling and casurina posts.

5.9.19: Centring and shuttering including strutting, propping etc. and removal of form for: Weather shade, Chajjas, corbels etc.,including edges. - Using with water proof ply 12mm thick Mango / silver wood scantling and Casurina posts.

5.12: Providing, hoisting and fixing upto floor five level precast reinforced cement concrete work in string courses, bands , copings, bed plates, anchor blocks, plain window sills and the like including the cost of required centring, shuttering, finishing smooth with 6 mm thick cement plaster 1:3 (1 cement : 3 fine sand) on exposed surfaces complete but excluding cost of reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

5.16: Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centring , shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

5.22.6: Reinforcement for R.C.C work including straightening , cutting , bending, placing in position and binding all complete - Thermo - Mechanically treated bars( TISCON / VIZAG / IISCO /SAIL / JSW) including placing the M30 grade Athees make cover block @ 60cm centre to centre.

5.25: Providing and fixing in position copper plate as per design for expansion joints.

6.1.2: Brick work with FPS bricks of class designation 35 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand)

6.12.2: Half brick masonry with FPS bricks of class designation 35 in foundation and plinth in cement mortar 1:4 (1 cement: 4 coarse sand)

6.38: Providing and laying autoclaved aerated cement blocks masonry with 100mm thick AAC blocks in super structure above plinth level upto floor V level in cement mortar 1:4 (1 cement: 4 coarse sand) The rate includes providing and placing in position 2 Nos. 6 mm dia M.S. bars at every third course of masonry work.

8.2.2.2: Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with whitecement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. - Granite of any colour and shade - Area of slab over 0.50 sqm

8.3.1: Extra for providing edge moulding to 18mm thick marble stone counters, vanities, etc.,including machine polishing to edge to give high gloss finish etc., complete. - Marble work.

8.3.2: Extra for providing edge moulding to 18mm thick marble stone counters, vanities, etc., including machine polishing to edge to give high gloss finish etc., complete. - Granite work.

9.1.1D: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position - Balasa teak wood .

9.6.2: Providing and fixing 35mm thick factory made laminated veneer lumber door shutter conforming to IS:14616 and TADS 15:2001 (part B) including ISI marked black enamelled M.S.butt hinges with necessary screws and panelling with panels of: 12 mm thick prelaminated (with particle board decorative lamination on both sides) grade -1, medium density flat pressed , three layer particle board FPT -1 or graded wood particle board FPT -1, conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and prelamination conforming to IS : 12823 grade 1, type -II marked.

9.9.1.2D: Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including black enamelled ISI marked MS butt hinges with necessary screws. - Balasa teak wood -30mm thick.

9.53: Providing 40x5 mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

9.76: Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality)

9.83: Providing and fixing IS:3564 make aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete.

9.92.1: Providing and fixing chromium plated brass handles with necessary screws etc. complete : - 125mm

9.95.2: Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete : 25x63x4mm.

9.96.1: Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screws etc.complete:- 300x16mm

9.97.1: Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with nuts and screws etc.complete:- 300x16mm.

9.97.2: Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc.complete : -250x10mm

9.97.4: Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc.complete : - 150x10mm.

9.100.1: Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc.complete :-125mm

9.101.1: Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc.complete - single rubber stopper.

9.101.2: Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc.complete - Twin rubber stopper.

9.102: Providing and fixing aluminium casement stays ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

9.119: Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2nos.of 150mm long brackets of 15x15mm M.S.square tube, the vertical door profiles to be reinforced with 19x19mm M.S.square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S.screws of 65/100mm size complete as per manufacturers specification .

9.120.1: Providing and fixing to existing door frames - 30mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S.tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top & bottom rails . M.S.frame shall have a coat of steel primers of approved make and manufacture M.S.frame covered with 5mm thick heat moulded PVC 'C channel of size 30mm thickness, 110mm width out of which 90mm shall be flat and 20mm shall be tapered in 45 drgree angle on either side forming stiles; and 5mm thick , 110mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on the inner side to form top and bottom rail and 130mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on both sides to form ..............

9.121: Providing and fixing Fiber glass reinforced Plastic (FRP) door frames of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. The laminate shall be molded with fire resistant grade unsaturated polyester resin and chopped mat. Doorframe laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibreglass from all sides. MS stay shall be provided at the bottom to steady the frame.

9.122.2: Providing and fixing to existing door frames - 30mm thick fibre glass reinforced plastice (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyster resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / polystyrene foam to be used as filler material throughout the hollow panel , casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS:14856:2000, complete.

9.134.1: Providing and fixing of 65mm Godrej Navtal lock of 6 levers etc complete

10.17: Providing and fixing M.S. fan clamp type I or II of 16mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

10.25.2: Steel work welded in built up section/ framed work including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In grating, frames, guard bar, ladder, railings, brackets, gates and similar works.

10.26.3: Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. G.I. pipes.

10.27: Supplying and fixing of steel grill work of m.s. angles, flats, squares and pipes including cost of welding charges, fixing in position in masonry walls with cement concrete 1:2:4 (1 cement : 2 course sand : 4 graded stone aggregate 12.5mm nnominal size) including one coat of priming coat etc. complete.

10.28: Providing and fixing AISI 316 grade stainless steel hand rail of 50mm (outer dia 2mm wall thickness) stainless steel pipe supported on 40x10mm stainless steel flat at 600mm centre to centre to a toatl height of 900mm from the finished floor level and fixing 4nos .of 25mm (outer dia and 2mm wall thickness) stainless steel pipe as guard rails through the S.S.flat , with a base plate of size 100x100x8mm, including fixing in the base plate in concrete / wall surfaces by 4 nos of M-8 anchor fasteners and polishing the entire stainless steel work to no.4 surface finish as per the direction of engineer - in - charge.

11.3.1: Cement concrete flooring 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

11.21.1.1: Providing and fixing 10mm thick acid and / or alkali resistant tiles of approved make(Somany /Johnson / Durastone) and colour using acid and / or alkali resisting mortar bedding and joints filled with acid and / or alkali resisting cement as per IS: 4457 complete. In flooring on a bed of 10mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand). Acid and alkali resistant tile.

11.21.2.1: Providing and fixing 10mm thick acid and / or alkali resistant tiles of approved make (Somany / Johnson / Durastone) and colour using acid and / or alkali resisting mortar bedding and joints filled with acid and / or alkali resisting cement as per IS: 4457 complete. In dado / skirting on 12mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand). Acid and alkali resistant tile.

11.26.1: Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand). 25mm thick.

11.27: Kotta stone slabs 25mm thick in risers of steps, skirting, dado and pillars laid on 12mm average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

11.36C: Providing and fixing 1st quallity ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 300 x 600 mm in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm. Including pointing in white cement mixed with pigment of matching shade complete. - size 300x600mm.

11.40.5: Providing and laying rectified ceramic rustic / matt finish floor tiles 600x600 mm or more (thickness to be specified by the manufacturer ) of commercial quality conforming to IS:15622 of approved make ( Somany / Nitco) in all colours shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

11.41.2B: Providing and laying Soluble salt vitrified floor tiles of size 60x60cm (thicknes to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS: 15622 of approved make (Nitco / Somany / Johnson / Asian) in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600mm.

11.51: Providing and laying 22mm thick factory made pre polished cement concrete flooring tiles of required colour and design over 20 mm thick cement mortar 1:4 ( 1 cement : 4 sand) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \ Dazzle \ Technic)

11.52: Providing and fixing PVC corner beading of required size to suit the thickness of the wall tile at the corner joints of dado works.

12.31.1: Providing 10mm thick plaster of Paris (gypsum anhydrous) ceiling upto a height of 5m above floor level over first class kail wood strips 25X6mm with 10mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) : Flat surfaces.

12.38.1: Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. , rain water pipes embeded in and including cement concrete blocks10X 10X 10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and cost of cutting holes and making good the walls etc. : 100mm diameter.

12.41.1: Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion, (i) single socketed pipes. 75mm diameter.

12.41.2: Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion, (i) single socketed pipes. 110mm diameter.

12.42.1.2: Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Coupler 110mm.

12.42.3.2: Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single Tee with door 110X110X110mm.

12.42.5.1: Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Bend 87.5deg. 75mm bend.

12.42.5.2: Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Bend 87.5deg. 110mm bend.

12.42.6.2: Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Shoe (plain)110mm shoe.

12.43.1: Providing and fixing Unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1 cement : 4 coarse sand) and making good the wall etc. complete. 75mm.

12.43.2: Providing and fixing nplasticised - PVC clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm.

12.70: Providing and fixing colour coated galvalume sheet of 550 M.P.A yield of AZ 150 strength formed as per patterned steel rib profile with the depth of 31mm pitch of 250mm and overall width of 1060mm and thickness 0.5mm with required J or C hook bolts and nets 8mm dia G.S paint and working etc., complete excluding the cost of purlin , rafter and truss etc.,

13.1.2: 12mm cement plaster of mix : Cement mortar 1:6 (1 cement : 6 fine sand).

13.3.1: 20mm cement plaster of mix 1:4 (1cement : 4 fine sand)

13.9.2: Cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement 20 mm cement plaster.

13.10: 15 mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating of neat cement on the roughside of single or half brick wall.

13.16.1: 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand).

13.26A: Providing and applying ready mixed wall putty (JK / BIRLA ) of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

13.30: 18mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5 (1 cement : 5 course sand) top layer 6mm thick with cement mortar 1:4 (1 cement : 4 fine sand). (Cost for 1 metre long and 1 cm wide band.

13.48.1: Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using primer as permanufacturers specifications - Two or more coats applied @ 1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm.

13.50.1: Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

13.50.3: Applying priming coat: with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.

13.61.1: Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or more coats on new work.

13.62.1: Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

16.1: Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

16.8.1: Brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metre - with FPS brick of class designation 75.

16.65: Providing and fixing glazed black board of required size using 5mm thick plain glass sheet front face finely ground and fixed in teak wood (Burma) frames of cross section 100x40 mm size made to the specified shape alround fixed with 3mm wooden fillets and stiffened at the rear side with teak wood reepers of size 45x18 mm along the height of board at the specified spacing at 45 cm c/c approximately and fixing in portion in the wall face with teak wood plugs and screws at an interval of 90cm approximately alround the frame including the cost of plugs screws etc. The rate shall also include painting the smooth face of glass (rear face of the glass board) and rear face of frame polishing the frame (front face) roughing the front face of glass black board etc.complete (Black board shall be measured internally for the purpose of payment).

16.95: Supplying fixing and commisioning of Suguna/Texmo /Sharp 1 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset, pumpset fixing in position and test run etc. complete.

16.96: Supplying fixing and commisioning of Suguna/Texmo /Sharp 2HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset, pumpset fixing in position and test run etc. complete.

16.118: Supply and fixing of sliding windows at all levels made out from Unplasticised Poly vinyl chloride frame (UPVC) of natural colour (PRISTINE WHITE) with outer frame of size 40x56x40mm / 102x56x40mm and for shutter frame of size 53x38x37mm for two track / three track sliding windows , with wall thickness of 1.8mm (+/-0.3mm). The section should be single glazing using (flush catch) single point locking. The gasket should be made of EPDM (Ethylene propylene dimonomer) and applying silicone sealants (GE make or wacker make) outside and acrylic sealent inside including single glazing of 5mm thick clear float glass. The sections should be reinforced with GI sheet of 1.5mm thick with suitable drainage grouting.

17.1.1: Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100mm sand cast iron P or S trap, 10 litre low level white P.V.C . Flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : white vitreous china orissa pattern W.C pan of size 580X 440mm with integral type foot rests.

17.2.1: Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever, conforming to IS: 7231, with all fittings and fixtures complete) including cutting and making good the walls and floors wherever required W.C pan with ISI marked white solid plastic seat and lid.

17.2.2: Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required - WC pan with ISI marked black solid plastic seat and lid.

17.4.1: Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350xmm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unions and G.I clamps complete, including paintings of fittings and brackets, cutting and making good the walls and floors wherever required. One urinal basin with 5 litre white PVC automatic flushing cistern.

17.6.1: Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings , standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I. clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc., wherever required: - Single squatting plate with 5 litre P.V.C. automatic flushing cistern.

17.7.4: Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps 32 mm CP brass waste of standard pattern including painting of fittings and brackets, cutting and making good the walls wherever required White vitreous china flat back wash basin size 550x400 mm with single 15mm CP brass pillar taps.

17.11.1: Providing and fixing white vitreous china laboratory sink with CI brackets CP brass chain with rubber plug 40mm CP brass waste and 40mm CP brass trap with necessary CP brass unions complete including painting of fittings and brackets cutting and making good the walls wherever required size 450 x 300 x150 mm.

17.11.2: Providing and fixing white vitreous china laboratory sink with CI brackets CP brass chain with rubber plug 40mm CP brass waste and 40mm CP brass trap with necessary CP brass unions complete including painting of fittings and brackets cutting and making good thewalls wherever required size 600x450x200mm.

17.28.2.1: Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete - Flexible pipe - 32mm dia.

17.32.2: Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing rectangular shape 453x357mm.

17.32.3: Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing oval shape 450x350mm(outer dimensions).

17.73.2: Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm weighing not less than 190 gm.

17.78.1: Providing and fixing CP brass health faucet of approved quality - 15mm nominal bore

18.7.2: Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipewith clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and testing of joints complete (Internal work exposed on wall) - 20mm nominal outer dia pipes

18.7.3: Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and testing of joints complete. (Internal work exposed on wall) - 25mm nominal outer dia pipes

18.7.4: Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and testing of joints complete. (Internal work exposed on wall) - 32mm nominal outer dia pipes.

18.9.4: Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete (External work) - 32mm nominal outer dia pipes.

18.9.6: Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete (External work) - 50mm nominal outer dia pipes.

18.17.1: Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 25 mm nominal bore.

18.17.2: Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 32 mm nominal bore.

18.17.3: Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) - 40 mm nominal bore.

18.18.1.2: Providing and fixing ball valve (brass) of approved quality complete. high or low pressure with plastic floats - 20 mm nominal bore.

18.18.1.3: Providing and fixing ball valve (brass) of approved quality complete. high or low pressure with plastic floats - 25 mm nominal bore.

18.21.2.1: Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore.

18.22.2: Providing and fixing CP brass shower rose with 15 or 20 mm inlet 150 mm diameter.

18.32.1: Constructing masonry chamber 30x30x50cm, inside with 75 class designation brick work in cement mortar 1:4 (1cement 4 coarse sand) for stop cock, with CI surface box 100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (one cement 5 fine sand 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortor 1:3 (1cement 3 coarse sand) 12mmthick finished with a floating coat of neat cement complete as per standard design with F P S bricks.

18.46.3: Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) 25 mm nominal bore.

18.48: Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank

18.49.1: Providing and fixing CP brass bib cock of approved quality conforming to IS 8931 - 15mm nominal bore.

18.51.1: Providing and fixing CP brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15mm nominal bore.

18.52.1: Providing and fixing CP brass stop cock (concealed) of standard design and of approved make conforming to IS 8931- 15mm nominal bore.

18.53.1: Providing and fixing CP brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 - 15 mm nominal bore.

18.58.1.2: Providing and fixing PTMT grating of approved quality and colour circular type 125 mm nominal dia with 25 mm waste hole.

18.60.1: Providing and fixing enclosed type water meter (bulk type) conforming to IS 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc, (The tail pieces if required will be paid separately) 80mm dia nominal bore.

19.4.3.1: Providing and fixing square mouth SW gully trap grade 'A' complete with CI grating brick masonry chamber with water tight CI cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design 180x150mm size P type with FPS bricks class designation 75.

19.7.1.1: Constructing brick masonry manhole in cement mortar 1:4(1 cement : 4 Coarse sand) R.C.C top slab with 1:2:4 mix (1 : cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortat 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm and 45 cm deep including CI cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) with F.P.S bricks with class designation 75.

19.30.1.1: Constructing brick masonry chamber for underground CI inspection chamber and bends with 75 class designation bricks in cement mortar 1:4 (1 cement: 4 coarse sand) CI cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab with 1:2:4 mix (1 cement :2 coarse sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 450 x 610 mm and 45 cm deep for single pipe line with F.P.S bricks.

19.32.1A: Making soak pit 2.5 m diameter 3 m deep with 45 x 45 cm dry brick honeycomb shaft with bricks of class designation 75 and 110mm dia UPVC pipe (type B) 1.8 m long complete as per standard design with F.P.S bricks.

19.33.1: Providing and fixing on wall /column face unplasticed - PVC soil and waste pipes (type-B) conforming to IS:13592-1992 including jointing with seal ring conformation to IS: 5382 leaving 10mm gap for thermal expansion - single socketed pipes 110mm diameter.

19.33.1A: Providing and fixing on wall face/column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - Single tee with door - 110x 110x 110mm.

19.33.1B: Providing and fixing on wall face / column face unplasticised - PVC moulded fittings/accessories for unplasticisd - PVC soil and waste pipes conforming to IS: 14735-1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - Single tee without door - 110x110x110mm.

19.33.1C: Providing and fixing on wall face/column face unplasticised- PVC moulde fittings/ accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735-1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - bend 110mm.

19.33.2: Providing and fixing on wall/column face unplasticised - PVC soil and waste pipes (type B) conforming to IS:13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - single socketed pipes 75mm diameter.

19.33.2A: Providing and fixing on wall/column face unplasticisd - PVC moulded fittings/accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion - Single tee with door - 75x75x75mm.

19.33.2B: Providing and fixing on wall face /column face unplasticised - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735-1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - Single tee without door - 75x75x75mm.

19.33.2C: Providing and fixing on wall face / column face unplasticised - PVC moulded fittings/accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 75mm.

19.33.2E: Providing and fixing on wall face / column face unplasticised - PVC moulded fittings/accessories for unplasticisd - PVC soil and waste pippes conforming to IS :14735 - 1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - head rest bend 75 mm.

21.1.1.1: Providing and fixing aluminimum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene felt etc. Aluminimum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminimum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings. (Glazing and panelling to be paid for separately) : For fixed portion. Anodised aluminimum (anodised transparent or dyed to yed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15).

21.2.2: Providing and fixing 9mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 grade 1 type II in panneling fixed in aluminimum doors, windows, shutters and partition frames with C.P. brass / stainless steel screws etc., complete as per architectural drawings. Prelaminated particle board with decorative lamination on both sides.

21.3.1: Providing and fixing glazing in aluminimum door, window, ventilator shutters and partitions etc., with PVC / neoprene gasket etc., complete as per the architectural drawings. (cost of aluminimum snap beading shall be paid in basic item) : With float glass panes of 4.0mm thickness.

21.3.2: Providing and fixing glazing in aluminimum door, window, ventilator shutters and partitions etc., with PVC / neoprene gasket etc., complete as per the architectural drawings. (cost ofaluminimum snap beading shall be paid in basic item) : With float glass panes of 5mm thickness.

21.4.1: Providing and fixing double action hydraulic floor spring of approved brandand manufacture IS : 6315 marked, for doors including cost cutting floors as required, embedding in floors and cover plate with brass pivot and single piece M.S. sheet outer box with slide plate etc., complete. With stainless steel cover plate.

21.17.3: Providing and fixing Anodised aluminium, minimum anodic coating of grade AC 15 grill of required pattern / design over the doors, windows and ventilators., etc, including fixing (but excluding the cost of the sections, which will be paid separately)

22.5: Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying a)cement slurry mixed with water proofing cement compound consisting of applying First layer of slurry of cement @ 0.488 kg / sqm. mixed with water proofing cement compound @ 0.253 kg / sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 Kg / sqm mixed with water proofing cement compound @ 0.126 kg / sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

30.7: Supply of Quary rubbish including stacking to department gauge for premeasurement and spreading required thickness as directed by the Engineer-in-charge.

Basic Rate 0367: Add or deduct for providing richer or leaner mixes respectively at all floor levels - Providing M-30 grade concrete by using 428 kg of cement per cum of concrete instead of M-20 grade B.M.C / RMC.

DGB CONSTRUCTIONS PVT LTD