PROVN OF SANITARY ANNEXURE AND SPL REPAIRS TO SECURITY FENCING

Amount

Excavating over areas not exc 1.5 m deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exc 1.5m wide & not exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches not exc 1.5 m wide and exc 1.5 m in depth but not exceeding 3.0 m for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out complete all as specified and directed

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removing excavated materials exc 50m but not exc 100m and depositing where directed at a level not exc 1.5m above the starting point in soft/loose soil complete all as specified and directed

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregates) in mass concrete complete all as specified and directed.

M&L for providing cement concrete (Design Mix) M-25 (using 20 mm graded stone aggregates) for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for providing cement concrete (Design Mix) M-25 (using 20 mm graded stone aggregates) for Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for providing cement concrete (Design Mix) M-25 (using 20 mm graded stone aggregates) for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for providing cement concrete (Design Mix) M-25 (using 20 mm graded stone aggregates) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for TMT bar 10 mm dia and over cut to length bend to shape required including cranking, bending spirally for hooping for column,hooking,end and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bar 6 to 8 mm dia cut to length bend to shape required including cranking, bending spirally for hooping for column,hooking,end and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for formwork to sides & soffits of plinth beam and sides of footing rough finished surface of concrete complete all as specified and directed

M&L for formwork to sides of clumns getting rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to sides & soffits of floor or roof beams, beam haunching , girders , bressum-mers, lintels, cantilivers including supports, overhanging etc, also splays between floor & beams etc fair finished surface of concrete flat complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing & similar work n. exc 200 mm thick ( Horizontal or sloping) fair finished surface of concrete flat complete all as specified and directed.

M&L for brickwork with sub- class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

M&L for brickwork with sub- class ‘B’ bricks straight or curved on plan to any radius in half thick brick wall built in CM (1:4) complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or comcrete surface in cement mortar 1:6, finished finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on fair faces of concrete surface in CM 1:3 on ceiling complete all as specified and directed.

M&L for two coat cement plaster, first coat 10mm thick in CM 1:6 and Second coat cement plaster 5mm thick in CM1:4 mixed with WPC surface finished even and smooth without using extra cement complete all as specified and directed. Note:-Water proofing compound shall be measured and paid separately

Supply only Integral water proofing compound complete all as specified and directed.

M&L for applying three coats of white wash on new ceiling surface including preparation of surface complete all as specified and directed.

M&L for applying two coats of acrylic distamper, white or tinted over a coat of wall primer and applying Birla / JK wall care white putty 1 mm thick for levelling the surfaces on new wall surfaces including prepration of surfaces complete all as specified and directed.

M&L for prepration of new surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ ltr and UV resistance as per IS 15489, Alkali & fungal resistance, dirt resistance exterior paint required shade ( company Depot Tinted) with silicon additives @ 1.43 Ltr/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 ltr / 10 sqm over new surfaces complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregates) as sub basees of floor and finished the surfaces even and rough to receive the topping layer complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B0 (using 12.5mm graded stone aggregates) as in floor complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tiles 0.11 but n. exc 0.18 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match colour/ shade laid over and including 15mm thick screed bed layer in CM 1:6 complete all as specified and directed.

M&L for glazed coloured ceramic tiles joint free of size 450mmx300mmx7mm thick laid over and including 10mm thick rendering in C:M 1:4 set and jointed in neat cement slurry and pointed in white/ coloured cement slurry and pointed in white coloured cement to match the shade/ colour of the tiles on vertical surfaces such as skirting, dado, etc., complete all as specified and directed.

S&F solid PVC frame ( single rebeted) of size 50x47mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid PVC moulded door shutters, 28 mm to 30 mm thick ( stile) with wood free EPS with 2- 4 or 6 raised panel design with 4 mm thick 3 D wood grain Moulded PVC sheet Polyurethane painted on the front face & 4 mm colour PVC sheet on back face complete all as specified and directed.

S&F steel ventilators with top hung shutter incl two pair of brass cup pivots, catch spring and pulley wheel complete al as specified and directed.

S&F Aluminium anodised, barrel tower bolts of ex truded section 200 mm long complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodise 125 mm size complete all as specified and directed.

S&F butt hinges, heavy weight, cold rolled mild steel, 100mm size and fixed complete all as specified and directed.

S&F steel tubing medium 15mm bore grade (ISI marked) galvanised with all fittings (ISI marked) and concealed or fixed complete all as specified and directed.

S&F steel tubing medium 20mm bore grade (ISI marked) galvanised with all fittings (ISI marked) and concealed or fixed complete all as specified and directed.

S&F 20mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F concealled stop valve/ angle valve 15 mm dia cast copper alloy, CP fancy type with long shank and cup screwed down, high pressure screwed both ends for iron pipe or for union fixed in pipe complete all as specified and directed.

S&F 20mm dia gun metal gate blobe gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe of 20 mm bore complete all as specified and directed..

S&F 20mm dia high pressure, with polythene float & flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F viterous China WHB white flat back size 550mmx400mm with and including MS brackets , CP Pillar Tap fancy type 01 No of 15mm bore, CP waste cupling 32 mm dia PVC waste pipe of suitable length and PVC connection 15 mm size with PTMT nuts of length 450 mm high pressure complete all as specified and directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) and including connection to trap & to flushing pipe antisymphonage pipe etc complete including making good to floor complete all as specified and directed.

S&F vitreous China premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified

S&F PVC low level flushing cistern of 10 ltr capacity including flushing pipe bend complete all as specified and directed.

S&F CP bib taps, casat copper alloy, fancy type with scrutch or butterfly handle, screwed down , screwed for iron pipe or for brass furrule of 15 mm bore and fixed complete all as specified and directed.

S&F stop valves 15 mm bore dia cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F chromium plated shower roses fancy type 125mm size with swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F CP Fancy type tubular towel rail 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F CP Soap Dish complete all as specified and directed.

S&F PVC connections 15mm bore, 450mm in length with both end brass/ PVC high quality nuts complete all as specified and directed.

S&F vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed

S&F vitreous China urinal partition white of size 310mmx700 mm complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid fixed to walls complete all as specified and directed.

S&F PVC( SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC( SWR) bends 75 mm dia complete all as specified and directed.

S&F PVC( SWR) bends 75 mm dia with accessable door complete all as specified and directed.

S&F PVC (SWR) 110 mm dia junction single T equal or unequal with access door complete all as specified and directed.

M&L 75mm dia PVC (SWR) multi floor trap with hinge type SS grating including jointing with solvant cement complete all as specified and directed.

S&F rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) three layer wall construction of capacity 1000 ltr hoisted and fixed in position ISI marked complete all as specified and directed.

S&F 150 mm bore Reinforced complete pipes, class NP2, laid and jointed complete all as specified and directed.

M&L for concrete bed to drain pipes of 150 mm bore using PCC 1:4:8 (D2) including packing under and haunching against the sides of pipes after they are lad and tested in complete all as specified and directed.

M&L for cutting chases, pinining in , in brick wall making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc. And cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exceeding 10 cm girth complete all as specified and directed.

M&L for 60mm thick machine made coloured precast concrete interlocking paver block, rubbed with gray cement and pigment any shape and size confirming to IS 15658- 2006 of M- 35 graid laid over and including stone dust coushion not less than 40mm thickness as per the directiom of of Engr-in Charge complete all as specified and directed.

M&L for 75 mm thick sand filling under the floor or in foundation including watering and consolidation complete all as specified and directed.

M&L for rendering 10 mm thick plaster on fair faces of roof concrete surface in CM (1:4) finished even and smooth with water proofing compount @3% by weight of cement concrete applied over roof slab complete all as specified and directed.. Note:-WPC shall be paid seperately under respective item

M&L for provn of water proofing roof treatment to RCC roof with approved modified membrane of weighting not less than 3 kg/ sqm comprising with items and all as specified as under :-

The surface of roof parapet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleared for all foreign matters such as fugus, mass dust etc by wire brushing and dusting. For cast iron drain outlets grooves shall be cut as specified and directed.

Oil based Bitumen primer confirmiong to IS-3384-1986 @ 0.3 Kgs per sqm to be applied on prepared surface till the surface is properly impregnated.

Applying one coat of hot blown grade bitumen 85/25 @ 1.20 Kg/Sqm polymeric water proofing membrane composed of 100 micron (+10%) high density Polyethylene sheet (HMDPE) as centr core, which is standwiched between high quality ploymeric bitumen mix having softening, high heat registance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacturers instruction etc.

Applying one coat of hot blown grade bitumen 85/25 @ 1.20 Kg/Sqm over mebrane.

Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surface complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete, brick work, masonary, etc and making good disturbed ground complete all as specified and directed.

Dismantling of fencing wire mesh of any type complete all as specified.

Excavating in post holes in any type of soil each not exc 0.5 cum , getting out and removing surplus soil to a distance not exc 50 m and making good the disturbed surface complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregates) as in foundation, filling, mass concrete, sub-floors, floors etc complete all as specified and directed.

S&F mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire , etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling bolting or riveting, etc, and similar work and similar conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Mild steel Round bars 10mm dia and over, cut to length, bent to shape required, includinig cranking, bending spirally for hooping of columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips quality confirming to Fe-410 W complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or sguare heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or screw nut n.exc 5 cm long dia of shank 12 mm complete all as specified and directed.

S&F chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed. Make:-TATA/SAIL/JINDAL

M&L for painting steel surfaces exc 10 cm in width or girth with two coats of synthetic enamel paint over a coat of red oxide Zinc chromate primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of newly steel and iron surfaces of any description n.exc 10cm in width or girth when connected with other painting, applying two coats of synthetic enamel paint over a coat of red oxide Zinc chromate primer complete all as specified and as directed

S&F Galvanised 2 strand steel barbed wire 2.24mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed. Make:-TATA/SAIL/JINDAL

Surface exacavation not exceeding 30cm deep and average 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in coping, benching to hold to lower portion of chain link fencing complete all as specified and directed.

M&L for concealed point wiring with 1.5 Sqmm PVC-FRLS insulated, sheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, including modular metal flush boxes & modular white cover plate with frame as per site requirement all fittings such as tees, bends, elbows, etc. of external diameter 20mm all as per site requirements PVC insulated & sheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and directed:-

For one light, fan point controlled by one switch

For one 5 Amp independent socket point controlled by one switch

For one 3 pin ,5 Amp socket point with other switch on the same board

All as per Srl item No.85 here in before but for power point wiring using with 2.5 sqmm PVC-FR LS insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead

S&F modular switch, one way, 6 Amp 230, 1 module complete all as specified and directed.

S&F socket modular 6 Amp-2/3 pin combined 2 module complete all as specified and directed.

S&F switch modular, single pole, one way,16 Amp ,1 module 230 Volt complete all as specified and directed.

S&F socket modular 6/16 Amp, 2/3 pin combined ,2 module 230 Volt complete all as specified and directed.

S&F ceiling rose, surface backlit,three terminal complete all as specified and directed.

S&F testing and commissioning of MCB SP 6-32 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed.

S&F double door metallic sheet metal enclosure for MCB DB double door TPN 4 Way 415 Volts with 200 Amps rated bus bars complete all as specified and directed. Note :- Cutting and chasing in stone masonary and making good the disturbed surfaces shall be included in the quoted rate

S&F TPN 63 Amps 415 V including making electrical coming/outgoing connections with lugs/thimbles complete all as specified and directed

S&F LED TL fitting 20 watt for surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver long life corresion resistance impact proof surface mounting IP66 Lumanires PC housing in opeal finish coverwith high brighness complete all as specified and directed.

S&F box type LED optic fitting 1x9 Watt 2 feet box type complete all as specified and directed

S&F exhaust fans AC single phase 230/ 240 V of size 300 mm sweep mettalic body with all accessories including making hole in stone /brick wall grouting & making good in all aspects complete all as specified and directed

S&F LED Bulk head designed for modern homes availave in PIR as well as non PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer complete all as specified and directed

M&L for provn of earthing complete with MS galvanized earth plate electrode 600x600x6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below normal GL) with top edge of plate not less than 1.5 M below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of CI or steel incl excavation, PCC (1:3:6) type C-1 chamber with CI cover 10 mm thick, 15 mm dia light grade , GI protection pipe, funnel with wire mesh, watering pipe of size 20 mm dia, medium grade, lugs, main earthing lead upto main switch/DB incl charcoal dust, salt etc all as shown in electrical plate No. 3 of SSR part-I 2009 specification complete all as specified and directed.

Supply, installation , testing and commossioning of solar hot water system (Evacuated tube collector) with and including back up electric supply, stainless steel hot water tank duly instaled with inlet & outlet , based on indirected transfer of heat of capacity 500 LPD complete all as specified and directed.

S&F rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) three layer wall construction of capacity 500 ltr hoisted and fixed in position ISI marked complete all as specified and directed.

M&L for GI tubing medium grade 25mm bore fixed on floor/ wall complete all as specified including all fitings complete all as specified and directed

Supply, fixing, testing of hot water pipe medium grade duly insulated with glass wool & aluminium cladding of 15mm bore complete all as specified and directed

M&L for screwing existing steel tubing for altration or additions or lengthening screw on pipe to form conectors of any size GI tubing complete all as specified and directed

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregates) as in foundation for staging of PVC water tank including fair finishing of outside surfaces complete all as specified and directed

M&L for frame work suitable for fixing of make up PVC water tank of capacity 250 Ltres and stainless steel hot water storage tank with MS angle iron 40mmX40mmX5mm thick duly painted with one coat of red oxide primer and two coat of synthetic enamelled paint fixed on PCC concrete complete all as specified and directed

Supply, Laying, joining and testing of XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 35 sqmm 3.5 core laid in trenches, ducts, pipes complete all as specified and directed

Excavation in trenches not exceeding 1.5m in depth and not exceeding 1.5 mtr wide in any type of soil for laying of cable complete all as specified and directed

M&L for dry sand cushioning 8 cm before and 15 cm after layering of the cable complete all as specified and directed. Note:-Punned thickness shall be measured and paid

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat size 250mm x 150mm x 40mm complete all as specified and directed

M&L for 40mm bore GI pipe light grade laid under road and path for passing cable complete all as specified and directed

M&L for submain wiring in replacement with 2 run of single core 4 sqmm PVC insulated copper conductor multi stranded wire along with 4 sqmm PVC insulated single core multi stranded copper conductor as earth wire in and including suitable size heavy duty PVC conduit complete all as specified and directed

pal enterprises

SAGAR MOTOR AND TRACTOR CO

v k builder

dipangashu barick and associates

maharaja construction and suppliers