SPECIAL REPAIR TO GYM HANGER AT AATS AND SPL REPAIR TO BLDG NO SP-20 (OFFRS MESS) OF 60 PARA FD HOSP UNDER GE (EAST) AGRA

Amount

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for providing PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in coping, bands, plinth course and junction of brick edging and brick lining for drains as in benching other similar works including use and wast of necessary form work complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed but except brick. Note:- Bricks obtained from item No 6shall be reused after cleaning.

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick SmartCare ready mix plasterfor External surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of acrylic polymer as well as concrete surfaces. complete all as specified and directed.

M&L for two coat water based premium acrylic smooth exterior paint apex ultima or equalent emulsion of approved Colour with silicon additive & Colour stay Technology. Excellent Dit Pick up resistance With low VOC less than 50 gram/ lite as per the LEEDS specifications, Anti Algal Properties in two coats @ 1.79 Itr (undiluted)/ 10 sqm diluted with water as per Manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 Ir per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as directed. Note:- (a.) The work pertaining to periodical services & Water Proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. Paint, Distemper, Putty etc. is proposed to be used by the contractor and approved by Garrison Engineer. (b) Masking of window/doors during spray painting using polythene film will be included. (c) Rate quotated includes work at any height (not.exc 10 mtr) incl necessary scaffolding /Centreing etc and cleaning the waste materials and debris from out of MoD land as directed and complete.

M&L for 10 mm thick SmartCare ready mix plasterfor Internal surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of single component polymer as well as concrete surfaces. complete all as specified and directed.

M&L for 5 mm thick SmartCare ready mix plasterfor ceiling surface is a specially designed ready to use cement based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering on bricks, block, stone walls over a coat of single component polymer as well as concrete surfaces. complete all as specified and directed.

M&L for applying two coats of oil bound distemper with roller on new decorated wall surfaces over 1 mm thick white putty including complete removal of existing treatment with mechanical complete all as specified and directed.

M&L for applying one coat of oil emulsion distemper with roller on old decorated wall surfaces including complete removal of existing treatment with mechanical complete all as specified and directed.

M&L for applying three coat of white wsah on new decorated wall surfaces including preparation of new plastered surfaces complete all as specified and directed.

S&F 7.5 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed.

Dismantling cast iron work/mild steel work of any description complete all as specified and directed.

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etcof grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed..

M&L for two coats of synthetic enamel paint over a coat of red oxide primer incl preparation of New steel surface complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surfaces of size 350 x 250x 7mm /450mm x 350mm x7mm thick set and jointed in neat cement slurry over 10 mm thick rendering in CM 1:4 for receiving the tiles complete all as specified complete all as specified.

M&L Non Skid ceramic coloured tiles 7mm to 8mm thick, area of each tile exc 0.11 Sqm but n. exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick cement mortar (1:6) screed bed for floor finishes complete all as specified complete all as specified.

M&L Virified Ceramic tiles light /dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed. (bed room and other room floor)

Dismantling wall and ceiling boards( fibre pulp, insulation etc.) or insulation board /slabs/blanket any thickness including cover fillets.

Providing & fixing false ceiling at all heights with PVC solid pannel to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

S & F PVC wall lining consisting of 8-10 mm thick wooden grain printed PVC sheet inclusive of solvent cement and fixing channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, at site on wall/ceiling as per specification and complete all as specified and directed.

PCC 1:3:6 C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate ways finished even and smooth without using extra cement all as specified.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings in roof cobvering complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F in repairs 15 mm bore chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers etc complete all as specified and directed.

S&F in repair 15 mm bore CP Stop valve / angle valve screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends with access door of any radius complete all as specified & directed.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed.

All as per item No 34.00 above but 20mm bore complete all as specified and directed.

Supplying and laying 25 mm outer diameter of CPVC pipes SDR 11 including CPVC Brass fittings (Brass elbow, Brass Tee, MTBA, FTBA etc), Unions, Ball valves, Flange and tank adaptor or necessary fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying 20 mm outer diameter of CPVC pipes SDR 11 including CPVC Brass fittings (Brass elbow, Brass Tee, MTBA, FTBA etc), Unions, Ball valves, Flange and tank adaptor or necessary fittings on walls/ceiling or laying in floors complete all as specified.

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed.

S&F in repairs Rotational moulded polyethylene water storage tanks with cover (cylindrical vertical with closed top) hoisted and fixed in position including fittings all as specified in SSR Part I (Capacity in litres 1000) Including taking down complete all as specified and directed.

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed

S & F in repairs Flushing jet for pedestal pattern WC incl .flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed.

Supply and fix in repairs CP Central hole basin mixture screwed for 15 mm dia pipes including PVC connection etc complete etc complete all as specified and directed

Supply and fix in repairs CP Sink mixture screwed for 15 mm dia pipes including PVC connection etc complete etc complete all as specified and directed

S&F in repair Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) of 32mm bore suitable for wash hand basin complete all as specified and directed.

S&F 32 mm dia PVC waste pipe for wash basin /sinks with cupling

S&F in repair 150 mm square grade of 304 stainless steel grating with openable flap (Min weight 100 gms)complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.50mm thick sheet glass 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 174 of SSR 2020 (Part-II)

S & F Solid PVC door frame for PVC doors, Kitchen cabinet of size 50mm x 47mm made out of 5mm PVC sheet reinforced with MS square tube, as shown on drawings as per manufacturers specification complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair 25 mm stainless steel curtain rod complete all as specified and directed by Engr-in-charge.

S&F SS heavy duty decorative brackets suitable for 25mm dia curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed. Note: Curtain rod shall be measured and paid separately

S & F Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed.

S & F Anodised aluminium window/ventilator frame/shutters powder coated, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S & F Stainless steel wire cloth, 0.71 mm nominal dia of wire fixed with tinned tacks, of 20mm mesh of stainless steel wire staples complete all as specified and directed

M&L Varoda green marble makrana Adanga stone 18 to 20 mm thick in steps, pillars, wndow cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S&F 5.0 mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed.

S & F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

M & L (Brushbond RFX) Elastomeric polymer modiffied cemtentitious waterproofing coating used for waterproofing of extg and new naked bricks surface complete all as specified and directed.

M&L for providing pre-cast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:6 with and including demolition complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately)

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with cli complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

M& L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the internal/external wall and wooden Cup board,shelves,etc.wooden area should drill by 6 mm bit,Gap between two holes is 30 cm to 45 cm internal/external wall skirting level should drill by 8/10/12 mm bit,gap between two holes is 45 cm to 60 cm.filling the holes by 100 ml to 150 ml dilution of chemical emulsion in two stages 3 stage close the holes by white cement and finsihes with existing surfaces.The ATT chemical should be odorless and mixed formulation should be injected at the rate of 5 ltr per sqm. The ATT chemical should contains. (i) Byfinthrin 20 % EC(Smell Chemical) (ii)CHLORPYRIPHOS 20 % EC (Smell Chemical) (iii) Imidacloprid 30.5 % SC (Odor less Chemical)

S&F in repair vitreous china Wash Basin counter Top 600x400x185mm including stainless steel bottle trap and 40 mm dia GI pipe up to Floor trap complete all as specified and directed by Engr-in-Charge

S&F vitreous china rimless single piece WC of Size: 380x700x665 mm, Single Piece WC with PP Soft Seat cover, Hinges, Fixing Accessories, Accessories Set, and Cistern fittings, P trap-180mm complete all as specified and directed.

S&F in repair Health Faucet (ABS Body) with 1.20 M Long PVC Tube and wall Hook screwed down to GI pipe or union/angle valve complete all as specified and directed by Engr-in-charge.

S&F in repair Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified and directed.

S&F in repair 15mm dia brass chromium plated Single Lever Sink Mixer With Swinging Spout on Upper Side (Wall Mounted Model) With Connecting Legs & Wall Flanges for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed.

Dismantling of boarding any description fixed in any position with nails complete all as specified and as directed .

S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification.

S&F auto closing hinges 35 mm of 0 crank( KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters.

S&F Ball bearing runners 45 mm Telescopic channel (KTS-20) full extension load capacity 50 kgs.

S&F chrome plated stainless steel wire basket (storage basket) pull out type for large utensils, size 480 x 500 x 150 mm of Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S&F chrome plated stainless steel wire basket (cup and saucer basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S&F chrome plated stainless steel wire basket (plate basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S&F chrome plated stainless steel wire basket (cutlery basket) pull out type, size 380 x 500 x 100 mm Grade 304 with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S&F chrome plated stainless steel wire basket (Grain Trolley) pull out type, size 480 x 500 x 200 mm Grade 304 with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed by engineer- in - charge.

Supply chrome plated stainless steel wire basket (Bottle pull out) pull out type two self, size 120 x 500 x 432 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.”

S&F width of flaps (When open) in 40 mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised.

S & F powder coated aluminium sections for doors, windows, partition including fabrication of frame and shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, provn of AC opening and rubber beadings for fixing glass panes in frame complete all as specified by Engr-In- Charge. Note : (i) Glass panes/wire cloth will be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading and glazing clips,hinges, handle. However it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

S&F of power coated any colour anodised aluminium door shutter, aluminium section weighting 0.55 kg/m incl necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F in repair for powder coated aluminium ventilator shutters with frame not less than 0.55 Kg/Rm, half bottom portion fixed with 4mm thick glass with fixed type shutter and top half portion lower type with 5 mm thick glass and outer side fixed with stainless steel wire mesh, shutters aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary aluminium fittings etc complete all as specified and directed.

S & F powder coated anodised aluminium three track sliding window made of extruded profiles with reqd size of aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings and plain glass on two shutters and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples on one shutters with two nylon roller on each shutters including star lock handle complete all as specified and directed.

Taking down of old roof treatment of any description including mud phushka, concrete padding,tiles,cement plaster from roof surfaces etc including cleaning ,brushing and watering to joints and grooves and throwing the demolition materials/waste, debris away from the MOD Land etc complete and the roof of height n.ecx 11 mtr etc complete all as specified and directed.

Material and labour for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in roof kerbs, paddings, mud stops slightly chamfered or rounded in edges including required grove cutting complete all as specified and directed.

M&L for Apply one coat of Cipoxy 16D primer in the ratio 1:1 spreading at the rate of 0.200 kg-0.250 kg /sqm in complete dry condition where moisture contain below 7% (should be checked with moisture meter)Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat of Roofseal Classic without dilution spreading at the rate of 0.70/litre/Sq.mt/Coat until all surface is covered. Lay a 45 GSM Fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no void surface is left untreated / uncoated.Allow the system to air cure for 7 days minimum etc complete all as specified & directed. Note : The contractor shall submit a gaurantee of 10 years from date of completion of work for waterproofing treatment alongwith manufacturers gauruntee. Contractor have to submit the FDR in the favour of GE (East) Agra before submitting the final bill @ 2.5 % of amount of this item.

S&F of Anodised aluminium snap grid frame work for false ceiling all as specified and directed

S&F of Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

S&F of Non asbestos fibre cement building boards 4mm thick fixed or laid/ inserted to timber/GI/ Aluminium framework with screws complete all as specified and as directed.

Dismantling of boarding any description fixed in any position fixed with screws complete all as specified and directed

S& F inrepairs Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. Note:- (I) Thickness of powder coatings shall be not less than 30 micron. (ii) Weight of the aluminiumnsections only shall be measured and paid. (iii) Aluminium doors window/ ventilators to be fixed to jambs with cadmium plate screws. (iv) The rate shall be inclusive of neoprene beadings, handles, hinges, screws etc. weight of fittings/fixtures will not be measured for ariving the weight of aluminium section. (v) Glass panes and panels shall be measured & paid separately under respective items. Design shall be approved from Engineer-in Charge as existing at sitebefore fabrication and bulk order to the manufacturer.

S & F inrepairs powder coated Anodised aluminium window and ventilator shutters,side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed.

S&F 100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed.

S&F 125 mm long Extruded aluminium alloy handles, fabricated type, complete all as specified and directed.

S&F 150 mm long Extruded aluminium alloy handles, fabricated type, complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and fixed with aluminum beading and gaskit suitable for aluminum frames in squares exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified.

S&F 6 mm thick aluminium composite pannel for clading and door and partations fixed with any colourn, partations and ceiling, etc fixed with screws, solvent cement, adhesive complete all as specified and directed

Demolition of brick work or rubbled stone masonry including all qoins arches , pillars etc built in cement mortar complete all as specified and directed

M&L for 15mm thick plastering in CM 1:4 thick on brick surfaces of walls & finishing the surface even & smooth complete all incl water proofing compound at any height incl necessary scaffolding /Centreing etc all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

S&F of 0.71 mm thick aluminium alloy colour coated roofing sheets of alloy IS designation 31500, temper H*8 conforming to IS 737 and dimension as per IS Code 2676 with characteristics of good formability and corrosion resistance and troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm at all heights, levels and locations. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/ tapping stainless steel screws M6, 60 mm long with 3 mm EPDM seal washer etc, all inclusive of labour, scaffolding, T&P and sundries etc.specified complete all as specified and directed.

S & F Providing and fixing 0.71 mm thick Precoated colour or mill finish Aluminium Ridges plain (500-600mm) of alloy IS designation 31500, Aluminium Alloy (AA) 3004 (ISO designation). For colour, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size M6, 60 mm long with 3 mm EPDM seal and SS plain washer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F of Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirimng Fe 410 -W (Gde- E- 250) quality- A welding to truss/ corrugated sheet complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M & L for preparation of old steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

M & L for machine cut Kota stone slab flooring 20-25mm thick incl 20 mm thick screed bed in CM 1:6. laid and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Plain cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate)as in surface channel and drain all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms , moulds mitred/stopped ends etc complete all as specified and directed.

Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box of suitable module as per site requirement not less than 1.6mm thick and connecting earth and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note:- Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch.

(b) One 5 pin socket outlet 5 Amps on same board .

(c) One 5 pin socket outlet 5 Amps on independent board .

(d) One bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per item No 120 here in before but with cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed by Engr-in-Charge.

Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed.

Supply and fixing modular socket outlet 2/3 pin 6 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular socket multipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed.

Supplying & fixing for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 1 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 4 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed.

Supply and fixing blank spacer plate for single module.

Supply and fixing in repair LED luminaire 36 watt, 220 V AC, surface/ recessed type with smart colour temp, CCT controllable 2x2 LED lighting with remote control with dimming and CCT change options from 2700K to 6500K, housing made from powder coated, CRCA sheet, opaque diffuser for glare free and optimum light suitable for roof ceiling including connecting up with driver and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangements for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified and directed. Note: -The period of defects liability shall be 02 Years from the date of installation of security light.

M&L for replacement of sub main wiring using two 2x6 sqmm single core PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 6 sqmm as earth continuity conductor connected to earth dolly including taking down old unsv submain wiring complete all as specified and directed. NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.

M&L for replacement of sub main wiring using two 2x4 sqmm single core PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 4 sqmm as earth continuity conductor connected to earth dolly including taking down old unsv submain wiring complete all as specified and directed. NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.

Supply & fix in repair of sheet metal enclosure Vertical TPN DB 4 Way double door, Suitable for Flush Mounting and Surface Mounting, With 250 A Copper Busbar for each phase with 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 DB's, With provision for 160 Amp MCCB as incomer and SP/TP MCB's as outgoing incl cutting/chasing of wall and make in good to the disturbed surface complete all as specified and as directed.

Supply & fix in repair sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link all as specified and directed.

Supply and fixing in repair Single pole and neutral modular type enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp, complete all as specified and directed.

Supply and fixing in repair MCCB 4 pole, 160 Amps, 50 Hz, Icu=36 KA at 415 volts with thermal magnetic alongwith adjustable magnetic protection for current setting Icu=Ics = 100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity standard complete all as specified and directed.

Supply and fixing in repair MCB SP 6 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fixing in repair MCB SPN 40 to 63 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

M&L in replacement for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:-(i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chas-es or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated sit-uation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire complete all as specified and directed.

Supply and fixing modular step type two module electronic fan regulator heavy duty 120watts 240 volts, complete all as specified and directed.

Supplying and fixing 20 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 20W, luminaire lumens > 2000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surge protection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certification and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified.

Supply & fixing LED security light compact & trendy of 35 watt with aluminium pressure diecast housing, IP 65 protection, luminaire lumens > 3000 lumens/W and in built electronic driver prewire upto terminal block with driver efficiency > 85 %, power factor > 0.95, as per IEC 61000-3-2, colour temp 6500 K Surge protection 3.5 KV, 50000 burning hrs (min) as per L70 Criteria, multi stage constant current operated driver with range 150-270 VAC and safety exra low voltage safe load < 60 VDC as per IEC standards with LM 70 & 80 certification complete all as specified, fixed to pole or wall of buiding with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.0 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 50x6 mm to be tightened with suitabe size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 Sqmm including all accessories and fixing arrangements for fixing the light fitting complete all as specified & directed.

Disconnecting & taking up or down existing unserviceable sub main wiring of copper/aluminium conductor of any description, any size & in any position including taking out existing unserviceable conduits or battens of any description and making good the disturbed surfaces to the existing surfaces all as specified and directed.

Disconnecting and taking down old unserviceable distribution boards any size any type including MCB TPN/SPN/SP etc and refixing of serviceable DBs including making good the disturbed surfaces to the existing surfaces complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 12 way with IP-43 protection double door complete with appropriate size bus bar and neutral link all as specified and directed.

S&F in repair sheet metal enclosure with socket plug top and MCB single pole and neutral with two pin and earth plug top with one SP MCB 20 Amp 240 volt complete all as directed all as specified and as directed.

Supply and fixing MCB SP 1 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fixing MCB SPN 63 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Dismantling, taking down exisitng ceiling fan/Exhaust fan and deposited to E/M store for re-fixing and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed.

Supply, fixing, connecting & testing ceiling fans complete with remote control, blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), and including suitable size of fan hook, clamps, nut & bolts if required at site, connecting wire with new 3 core 0.50 Sqmm PVC insulated and sheathed copper conductor cable from ceiling rose and also writing MES No with black paint complete all as specified and directed.

Supply and fix in replacement electric water heater, storage type steel body with S/S inner tank and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc also writing MES No with black paint complete all as specified and directed.

Singh Contractor and Supplier (BID ID -3507852)

M/s Navansh Engineers & Consultants (BID ID -3509119)