SPECIAL REPAIR TO MD ACCN BLDG NO 111/1 TO 111/08 (QTR) BHAGAT COLONY AT NASIRABAD

Amount

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc 15cm thickness (above or below GL) complete all as specified and directed

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

Taking down cement or cement lime plaster or stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area n. exc 1.5 Sqm each complete with hold fasts etc complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area exc 1.5 Sqm but n. exc 4.0 Sqm each complete with hold fasts etc complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but n. exc 2.00 Sqm and easing, adjusting and also refixing builders hardware as required and renewal of unserviceable screws and refixing in the same opening complete all as specified and directed.

Taking down shutters of any description exc 2.00 sqm and easing, adjusting and also refixing builders hardware as required and renewal of unserviceable screws and refixing in the same opening complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar etc complete all as specified and directed.

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for walling Random rubble masonry uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc complete all as specified and directed.

All as per item No. 11 here in before but except stone complete all as specified and directed.

Extra over stone masonry for hammer dressing to face beds and joints maximum depression on face (sand stone) n. exc 20mm depression etc complete all as specified and directed.

M&L for rendering in cement mortar (1:6), 15mm thick on other than fair faces of brick work / stone masonry surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar in CM (1:4) on ceiling finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @ 3 % by weight of cement on other than fair faces of brick / stone masonry surfaces, finished even and smooth without using extra cement, complete all as specified and directed NOTE:- (WPC shall be measured and paid separately)

Dismantling loose / disintergrated portion of RCC Chajjas, bend shelves, beams balconies and similar work at any position or any height and dubbing out with PCC 1:1.5:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished required shape including applying anti corrosive paint on exposed surfaces and provision of necessary supporting form work and including 10mm thick plastering in CM 1:4, finished fair and even, complete all as specified and directed.

M&L for rough cast plaster over 10mm thick cement plaster in cement mortar 1:4 on stone / brick masonry wall surfaces complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but not exc 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

Ditto- all as per item No.20 above but in skirting over 10mm thick screeding in cement mortar 1:4 complete all as specified and directed.

M&L for machine cut kota sotne slab, 20-25mm thick over and including 15mm thick screed bedding in cement mortar 1:6 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing with mirror polish complete all as specified.

M&L for machine cut kota sotne slab in skirting / steps / risers of reqd size, 20 to 25mm thick & including 15mm thick screed bedding in cement mortar 1:4 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing with mirror polish complete all as specified and directed.

M&L for RCC type B-1 (1:2:4) using 20mm graded aggregate in slab supported on wall walls beams and columns in floors roof landings complete all as specified and directed.

M&L for TMT bars of 6 to 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9 mm dia complete all as specified and directed.

M&L for form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exceeding 200mm thick complete all as specified and directed.

M&L for 16 to 18mm thick granite ( of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edge of stone slabs one edge complete all as specified and directed.

M&L for rolled mild steel work as in door frame (chowkhats ) including provn of 10mm dia deformed bar welded horizontally to bottom of frame conforming to Fe-290 (Gde 165-E) including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed. Note:- Weight shall be verified by the GE.

S&F Second class HW, plain, solid, straight chowkhats & frames, wrought, framed, rebated on the solid, rounded or chamfered, put together glue pinned at joints complete all as specified and directed.

S&F Second class HW 35mm thick, plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS : 1003n (part I), Kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F solid PVC moulded door frame of size 50mm x 47mm made out of 5mm prelam coloured PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet as reinforced with MS square tube and fixing in opening as specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam (Nut Brown colour ) PVC sheet on the front face & 2mm prelam (Nut Brown colur ) PVC sheet on back face, and fixing inthe frame at site as per specification and drawing on page 161 of SSR (Part -II ) 2010 complete all as specified and directed.

Taking down old u/s steel window / ventilator and S&F steel window / ventilator glazed and gauged (combination) with side hung / top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame including guard bars and necessary cooler arrangement in window complete all as shown in drg No. CEBZ /TD / 14/11 Sheet No. 1/7 to 7/7 complete all as specified and directed.

Dismantling boarding of any description fixed with nails in any position and M&L for 18/19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, fixed with screws, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and pelment boxes, cupboard, shelves etc all as specified and directed.

S&F continous (Piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertaure 1.40mm and fixed with tinned tacks or stainless steel wire staples all as specified and directed.

S&F 3mm thick glass, ordinary quality, 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane, complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in square n. exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F MS butt hinges, medium weight, cold rolled, ISI marked of size 100mm, complete all as specified and directed.

S&F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge and anodised ISI marked and fixed, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section all as specified and directed.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F hasp & staple 100mm size safety type, aluminium anodised with mild steel hinges pin including bolt of hinge plate & fixed with screws complete all as specified and directed.

S&F 300mm long alumimium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium alloy all as specified and directed.

S&F 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

S&F 25mm mild steel chromium plated curtain rod powder coated finished complete all as specified and directed.

S&F decorative type curtain rod bracket with cap of mild steel powder coated suitable for 25mm dia rod complete all as specified and directed.

S&F Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for mild steel work such as hold fasts, hooks, clamps etc and similar work conforming to Fe 290 , Gde -165 complete all as specified and directed.

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

S&F 15mm GI water tubing( Concealed type), medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 20mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F 25mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

Refixing old 15mm GI tubing (Concealed type) galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Refixing old 20mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Refixing old 25mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

Dismantling of existing unserviceable RCC/PVC water tank and S&F 500 Litres capacity rotational moulded polythene water storage tanks(cylindrical vertical with closed top ) hoisted & fixed in position complete all as specified and directed.

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms)

S&F in repair tubular towel rail, chromium plated brass 20mm dia 'D" type 60cm long between flanges complete all as specified and directed.

S&F in repair brass chromium plated shower rose of 125mm size with swivel joints, including fixing to steel pipe or union of 15mm bore complete all as specified and directed.

S&F in repair PVC valve less, syphonic action type flushing cistern, 10 Litre capacity, low level, white with inlet, ball vlave float, handle including PVC rigid pipe 32mm bore as flush pipe fixed on walls by drilling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S&F in repair wash hand basins vitreous china, coloured flat back size 550 x 400mm fixed including bracket complete all as specified and directed.

S&F in repair PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S&F in repairs 15mm pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure for iron pipe fixed complete all as specified and directed.

S&F in repairs 15mm bore cast copper alloy chromium plated bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repair angle valves 15mm bore , cast copper alloy chromium plated with long sunk and cap (Concealed type), screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as spcified and directed.

S&F mild steel framed work such as grills, grating cooler stands, etc, with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L providing 50x50mm aluminium anodised grills mesh for fixing in wooden gauged door shutter weight not less than 1.2Kg/ Sqm complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description from sunken floor (ground or Ist floor) and removing and depositing materials exc 150 Mtrs but n. exc 250 Mtrs away complete all as specified and directed.

M&L for mass concrete filling using PCC (1:5:10) type E2 in sunken floor complete all as specified and directed.

M&L 20mm thick cement plaster in CM 1:4 mixed with water proofing compound @ 3% and applying water proofing treatment on sunken portion with acrylic base polymer modified cementitious composit compound as specified and approved & cement slurry two layers, Ist layer @ 0.488 Kg /Sqm mixed with composit compound @ 0.253 Kg /Sqm, & the second layer slurry @ 0.242 Kg /Sqm mixed 0.126 Kg of compound complete with min 4 hours allowed to air cure between these layers and applying 200 u polyflim with adhesive complete all as specified and directed.

Taking out old u/s water closet and S&F vitreous China "Orissa pattern" size 580 x 440mm" coloured, with intergral foot rests with vitreous china 'P' or 'S' trap front or back inlet including connection to trap and to flushing pipe, anti syphnage pipe and making good the floor to match the existing complete all as specified and directed.

Supply only liquid water proofing compound of approved quality and make confirming to IS complete all as specified and directed.

Taking down 100mm / 75mm dia AC rain water pipe (any size or pattern ) including all fitting, heads, shoes, bends and removing from sites complete all as specified and directed. (Measured over all as fixed along the centre line over the fittings and accessories)

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) vent cowl complete all as specified and direted pleases.

S&F PVC (SWR) reducers 75/110mm bore complete all as specified and directed.

Taking down existing tar felt or of any description including cement plaster or concrete of any thickness from the roof surfaces of building including cleaning the surfaces in all respect & preparing it for further treatment & removing rubbish from site complete all as specified and directed.

Material and labour for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on fair faces of RCC/stone patti roof surfaces finished even & smooth without using extra cement complete all as specified and directed NOTE: (WPC shall be measured and paid separately).

M&L for cutting out cracks to 'V' section in existing roofs or terracing, cleaning out and filling solidly with hot mixture of bitumen and clean dry sand 1:1(by weight ) complete all as specified and directed.

M&L for roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 mircron high molecular high density polyethylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 mircron HMHDPE film weight not less than 3 kg/ Sqm applied with bonding material using blown type bitumen primer Grade 85/25 @ 1.20 Kg/Sqm over bitumen primer conforming to IS -3384 @ 0.40 Kg /Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg /Sqm over APP membrane with all overlaps complete all as specified and directed

M&L for cement concrete M-10 (Nominal Mix) type C-1 using 20mm graded aggregate as in surface channel and drain complete all as specified and directed.

Extra for fair finishes drain or channel 30cm and over in girth in cement concrete using extra cement including forming mounds metred /stopped ends etc complete all as specified and directed.

M&L for 75mm thick cement concrete type D-2 1:4:8 (40mm graded stone aggregate ) as in floors / pavings complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment coloured, reflective type of approved quality laid over and including 25mm thick sand cushioning vibrated with mechanical vibrator complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 50mm thick as in plinth protection finished fair & even laid in alternative bays n. exc 2M in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

Taking down old wooden plate rack and S&F stainless steel plate rack made of 0.50mm thick of over all size 920mm x 785mm x 255mm and weight not less than 7.00 Kg each of approved quality complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and n. exc 1.5m deep and getting out in soft loose soil complete all as specified and directed.

Demolition and breaking up drain pipe SWG line set in CM of description, 100mm dia including side packing / haunching complete all as specified and directed.`

M&L for PCC 1:3:6 type C-2 using 40mm graded aggregate for bed concrete to drain pipe packing under haunching for sides for 100mm dia SWG pipe lines complete all as specified and directed.

M&L for SWG drain pipe grade 'A' 100mm dia laid in trenches incl jointing in CM 1:3 complete all as specified and directed.

Returning and filling in approved earth including levelling spreading watering and well ramming in any layers n. exc 25cm thick complete all as specified and directed.

Removing excavated materials n. exc 100m and depositing where directed and complete all as specified and directed.

Dismatling stone slab of any description laid, bedded and pointed in any mortar in floors complete all as specified and directed.

S&F in repair new rigid PVC waste pipe of approved quality 32mm bore, 75mm long with one end socketed fixed to waste coupling including one PVC reducer 32mm complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10CM width or girth and applying one coats of synthetic enamel paint over a coat or red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description not otherwise descriped over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wall surfaces and appling two coats of oil bound distemper over a coat of 1mm thick average thick wall putty, complete all as specified and directed. NOTE: Thickness of putty shall be as per manufacturer Instructions.

M&L for preparation of newly plastered surface of wall and apply two coats of oil bound distemper over a coat of 1mm thick wall putty, complete all as specified and directed. NOTE: Thickness of putty shall be as per manufacturer Instructions.

M&L for two coats of white washing to old ceiling surfaces including preparation of surfaces complete all as specified and directed.

M&L for two coats of white washing newly plastered wall surfaces including preparation of surfaces complete all as specified and directed.

M&L for two coats of cement base paint over old wall surface including preparation of surfaces complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of primer, complete all as specified and directed.

S&F in repair 20mm bore stop valves fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions fixed complete all as specified and directed

S&F in repairs 25mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engr-in-Charge.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit of any type and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed by Engr-in-Charge. .

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

One light point controlled by two Nos two way switch.

Ditto- all as per item No. 126.04 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as specified and directed by Engr-in-Charge .

S&F Switch piano, flush type, single pole, one way, 5 Amps, 240 volt, 50Hz, AC, complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as speciied and directed by Engr-in-Charge.

S&F switch piano flush type 5 amps, single pole two way 240 volts complete all as speciied and directed by Engr-in-Charge.

S&F bell push piano flush type 5 Amp complete all as speciied and directed by Engr-in-Charge.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as speciied and directed by engr-in-Charge.

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type complete all as speciied and directed by Engr-in-Charge.

S&F ceiling fan regulator electronic flush , stepped (four step) 230 Volts AC complete all as speciied and directed by Engr-in-Charge.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as speciied and directed by engr-in-Charge

S&F door bell ding dong type electric 230 volts AC , single phase, complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate complete all as speciied and directed by Engr-in-Charge.

S&F LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired . Make :- Crompton Cat Part No LTT8-20 for tube , IGP161LT8-16 for batten or equivalent model of Philips/Wipro/Havells

S & F wall mounted decorative luminaire fitting suitable for LED lamp B-22 base 9 watt complete all as specified and directed by Engr-in-Charge. Make: Havells , Model- CITY-1 or or equivalent model of Mepro/Philips

Supply and fixing LED lamp 9/11 watt suitable for 230 volts , 50 Hzs, B-22 base complete all as specified and directed.

S&F LED bulk head luminaire 1x 10 W bulk, IP 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed.

Supply and fixing and testing energy saving street light luminaire 15 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make : Havells, Cat Part No. ENDURAPEARLSL15WLED757SASYTOPC, or equivalent model of Crompton/Philips

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr length fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Disconnecting and taking down existing electric meter and refixing the same electric meter, connecting, testing and sealing properly and making good disturbed surface of walls etc.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl connecting up with three core flexible cable from ceiling rose to fan.

S&F MCB distribution board single pole & neutral (SPN) 08 way, IP-43 double door metal, double made out of CRCA sheet steel , factory made powder coated with 200 amp rated insulated bus bars , shrouded neutral bars, earth bars , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's complete all as specified and directed . Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F MCB distribution board triple pole & neutral (TPN) 04 way, IP-43 double door metal, double made out of CRCA sheet steel , factory made powder coated with 200 amp rated insulated bus bars , shrouded neutral bars, earth bars , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's complete all as specified and directed . Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge. . Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S&F MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing .

Note for all items: All items shall be executed as specified and directed by Engr-in-charge.

M/s SUNIL ENTERPRISES

M/S SHIVA TRADERS

MITTAL ENTERPRISES

kirtiman traders

V K LAKWAL CONSTRUCTIONS

M/S Nexus Projects

PD GUPTA AND COMPANY