MAINT OF ROOF COVERING AND JOINERY OF ACCNS IN RAKHMUTHI MIL STN AND ITS OUTSTATIONS UNDER GE (SOUTH) AKHNOOR

Amount

Dismantling of mild steel work of any description.

Hand rails, half round or other steel section or core for wooden hand-rail straight portion drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

Dismantling of Timber scantling under 40 sq.cm and over in section, in any position.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410 (Gde-E-250) quality-B, complete all as specified and as directed by Engineer-In-Charge.

Rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe 410-W (Gde- E- 250) quality-A, complete all as specified and as directed by Engineer-In-Charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-In-Charge.

Cement sheeting, grey, 6mm thick, non-asbestos, corrugated or semi-corrugated sheets in roofs, walls etc., walls etc, fixed with 'L or 'J' type hooks or cranked hook bolts, complete all as specified and as directed by Engineer-In-Charge.

AC serrated ridge for corrugated or semi corrugated sheets all as specified and directed

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including any pattern roof coverings, complete all as specified and directed by Engineer-In-Charge.

Galvanised, corrugated mild steel sheeting, 0.63mm thick, with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts sand washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and as directed by Engineer-In-Charge.

Plain, galvanised, mild steel sheeting, 0.80mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, fixed with L-type or J-type or cranked hook bolts sand washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and as directed by Engineer-In-Charge.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-In-Charge.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-In-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing ceiling board 4.0mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, including suspender wire of size 4.0mm dia of galvanised iron adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 4.0mm dia, length as required at site incl hooks, fastners, plate etc as required and as directed, complete all as specified and as directed by Engineer-In-Charge.

Dismantling of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles, complete all as specified and as directed by Engineer-In-Charge.

Brickwork with subclass ‘B’ bricks, old size bricks, straight or curved on plan exceeding 6.0mtrs mean radius built in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

All as per srl item No 17.00 above but except bricks.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed by Engineer-In-Charge.

Rendering 15mm thick, on any surface of brick or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Rendering 15mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:4, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a primer coat of chalk whitening, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint, complete all as specified and as directed by Engineer-In-Charge.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of cement paint, complete all as specified and as directed by Engineer-In-Charge.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying one coat of oil bound distemper (different colour), complete all as specified and as directed by Engineer-In-Charge.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed by Engineer-In-Charge.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4 sqm each with shutters (without taking off shutters from the frames).

Taking down chowkats or frames not exc 1.5 Sqm each with shutters (without taking off shutters from the frames).

Taking down shutters of any descriptions area exceeding 1.00 Sqm but not exceeding 2.00 Sqm, complete all as specified and directed by Engineer-In-Charge.

Taking down shutters of any descriptions area exceeding 2.00 Sqm, complete all as specified and directed by Engineer-In-Charge.

Factory made steel window, ventilator, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and glass sheet 3.0mm thick, 4mm thick frosted glass jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD/1517/15, sheet No- 1/3 to 3/3 and as directed by Engineer-In-Charge. Note :- Cost of all items/elements eleborated in the specification and in Drawing shall be deemed to inlcude in quoted rate.

Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.

Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc.

30 mm thick 2nd class hard wood glazed shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted wifth cut and mitred beads for securing glass, gauge etc, sizes of members of shutters as specified in SSR Part I, Sec-8, clause 8.24(a), complete all as specified and directed.

30 mm thick 2nd class hard wood plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board, medium density, wood particle board with commercial face veneered supplied & fitted to chowkat.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube including making good disturbed surfaces of wall complete.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struk inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointing together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

100 mm long mild steel butt hinges, medium weight cold rolled and fixed complete all as specified

150 mm long Extruded aluminium alloy handles, fabricated type, anodised ISI marked complete

150 mm long aluminium, anodised, barrel tower bolts of extruded section ISI marked complete all as specified

300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed.

300 mm, mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 150mm, fixed in floor, complete all as specified and as directed.

100 mm long mild steel butt hinges, medium weight cold rolled and fixed in repair complete all as specified

150 mm long Extruded aluminium alloy handles, fabricated type, anodised ISI marked fixing in repair complete all as specified

150 mm long aluminium, anodised, barrel tower bolts of extruded section ISI marked fixing in repair complete all as specified all as specified

300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy fixing in repair complete all as specified

300 mm, mild steel ordinary rat tail, rod pattern springs including roller and roller plate fixing in repair complete all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 150mm, fixed in floor,fixing in repair complete all as specified and as directed.

Amount of Schedule of credit of for Rs 1,33,590.00 shall be deducted from quoted amount.

KRISHNA BUILDERS (BID ID -3080043)

M/s Vishal Engineers (BID ID -3094705)

RAMA CONSTRUCTION COMPANY (BID ID -3091129)