REPAIR OF PUMP, MOTOR, SUBMERSIBLE PUMP SET AN SCADA SYSTEM ITEMS UNDER GE NASIRABAD.

Amount

Testing and taking out all defective/burn out parts from SCADA panel by replacing the defective/worn out parts at same place and checking conectivity from buttefly valve, Starter, Moter, OHT/UG Sump and main SCADA master panel at Rajmahal Pump house by authorised rep/SCADA company rep including installation, testing and commissioning complete for satisfactory performance complete all as directed by Engr-in-Charge. Note :- Spare parts shall be measured and paid separately under relevant items.

S&F in replacement of defected/ burn out /unsafe internal control wiring and connection for automation main master panel or automation slave panel installed at variours pump house for scada system as per existing system and including using by FR PVC insulated electric wire with copper conductor wiring having of single core of size 0.5 sqmm to 1.0 sqmm sub wiring as properly electrical connection for smooth controlling panel of scada system including resetting of system complete all as directed by Engr-in-Charge.

Taking out complete defective SCADA panel and re-fixing another safe location complete with cable connection outgoing/incoming cable and replacing the defective/worn out parts at same place and checking conectivity from from buttefly valve, OHT and main SCADA master panel at Rajmahal Pump house by authorised rep/SCADA company rep including installation, testing and commissioning complete with fixing arrangement complete all as directed by Engr-in-Charge. Note :- Spare parts shall be measured and paid separately under relevant items.

Supply & fix in repair single phase preventor Model 1 : VSP D2 complete all as specified & directed. Make: Minilec/ L&T / Schneider

Supply, installation, testing and commissioning relay pin type 4C/O , 220 -240Volt AC or as per exiting sample/ model No. Make : LEONE / IDEC/ SCHNEIDER/ESBEE

Supply, installation, testing and commissioning relay pin type 4C/O , 24 Volt DC or as per exiting sample/ model no. Make :- LEONE/IDEC/OMRON

Supply, installation, testing and commissioning indicator lamps of colour red / green/ yellow as per exiting sample/ size Make : LEONE / IDEC/SCHNEIDER/ESBEE

Supply, installation, testing and commissioning push button with Led indicator red/ green type -240 Volt Ac as per exiting sample/ size Make : LEONE / IDEC/SCHNEIDER/ESBEE

Supply & fix in repair PLC (Programmable Logic Controller) complete all as specified and directed. Make :Mitsubishi / GE Fanuc / Unotronics

S&F I/O module for Programmable Logic Controller Make :Mitsubishi / GE Fanuc / Unotronics

Supply, installation, testing and commissioning HMI - GS Series ,Graphic Touch Terminal; 7'' Screen; TFT Color Display with 800x480; 65K colors; 24 VDC”, RS 232- 485 & USB PORT interference for PLC based panel Make :Unitronics / Mitsubishi /Renu or Equivalent Make

Supply, installation, testing and commissioning buzzer system with base electrical connector as per existing size/type and suitable for showing to fault level of scada automation slave panel complete all as specified and directed by Engr-in-charge Make - Mimic or equivalent make

Supply, installation, testing and commissioning of Ultrasonic Level sensor with specifications:Range: 0-5 Meters Make: BANNER,SBEM and E+H

Supply, installation, testing and commissioning Butterfly valve of size 100/150 mm dia. Make: L&T/BIR or equivalent

Supply, installation, testing and commissioning Butterfly valve of size 200 to 300 mm dia. Make: L&T/BIR or equivalent

Repair of Butterfly valve Electric motor complete with as per existing copper winding wire suitable for actuator of size100mm to 300mm complete all as specified and directed

Repair of butterfly valve gear Box complete with electric circit plate of size 100mm to 300mm complete all as specified and directed :- Make AUDCO/VIRGO/L&T/INTERVALVE /BIR

Supply, installation, testing and commissioning 6 Core 1.5 sq. mm PVC sheath PVC insulated copper armoured cable. Make: Havells/Nicco/Plaza/Polycab

Supply, installation, testing and commissioning 2 Core 1.5sq.mm. PVC sheath PVC insulated copper armoured cable. Make: Havells/Nicco/Plaza/Polycab

Supply & fix in repair capacitor for Actuator suitable for 100/150/200/300 mm dia Motorized Butterfly Valve complete all as specified and directed Make as per existing

Supply & fix in repair resistor for Actuator suitable for 100/150/200/300 mm dia motorized Butterfly Valve complete all as specified and directed.Make as per existing

Supply & fix in repair SMPS input 230 V, AC, Output 24V, DC complete all as specified and directed. Make: As per existing

Repair of butterfly electric motor with gear box valve set of size 100/150/200 mm dia complete single phase motor actuated with disc material of CI with nylon coating, hand wheel for manual operation, pressure rating of 10 kg/sq cm and having 02 nos limit switches for open / closed condition and capability of accepting 4-20mA input complete set all as specified and directed by Engr-in-charge

Supply & fix in repair GPRS Modem complete all as specified and as directed. Make :- MAESTRO/MOTOROLA / VISIONTEK

Supply & fix in repair 9DB antenna for GPRS Modem complete all as specified and as directed. Make : Pentagon/Kenstel/Maxon

S & F star delta starter suitable for 7.5 - 10 HP motor over load relay range 8 to 12 Amps complete with Ampmeter and volt meter all as specified and directed. Make, Havells/L&T/ABB/BCH

Taking out old unserviceable starter and supply and fixing new starter DOL 3. phase AC supply 415 volt suitable upto 3 HP motor,over load relay range 2.5 to 10 amps Make :Make, Havells/L&T/ABB/BCH

M &L for applying two coat of synthetic enamel paint over old painted steel/iron surface of following pump motor complete as specified and directed by Engr-in -charge.

Moter and pump 150 HP complete

Moter and pump 60 HP complete

Moter and pump 10/12.5/15 HP complete

Replacement of unserviceable MCCB 250 Amps current carrying capacity 36 KA , AC 415 Volts 3 pole MCCB with Electronic Sg (LSIg) Protection Unit setting Ics=100%Icu Protection against overloads, short circuits and ground fault complete with Overload and Pre- overload Alarm Indication all as specified and directed. including dismentling the existing with all connections & fixing the new with all connections all as directed by Engg-in-charge Make Legrand/ABB/SIMENS/Havells

Replacement of unserviceable MCCB 400 Amps current carrying capacity 36 KA , AC 415 Volts four pole MCCB with Electronic S2 (LSI) Protection Unit setting Ics=100%Icu Protection against overloads short circuits complete Overload Alarm Indication - I > 1.05 Ir all as specified and directed. including dismentling the existing with all connections & fixing the new with all connections all as directed by Engg-in-charge Make Legrand /ABB/SIMENS/Havells

Replacement of unserviceable Contactor wth 3 Pole type CTX3 of Cap 225 A for star delta starter of cap 150 HP Make As per existing

Replacement of unserviceable contactor with 3 Pole Contactor type CTX3 of cap 150 A for star delta starter of cap 150 HP Make As per existing

Replacement of unserviceable contactor with 3 Pole Contactor type CTX3 of cap 100 A for star delta starter of cap 60HP MakeMake As per existing

Replacement of unserviceable contactor with 3 Pole Contactor type CTX3 of cap 18 A for star delta starter of cap 12.5/10HP MakeMake As per existing

Replacement of unserviceable Thermal relay with 3 Pole Thermal relay type RTX3 225 for Star Delta starter of Cap 150 HP thermal over Load relay ranging from 160 A to 240 Amps Make Make As per existing

Replacement of unserviceable Thermal relay with 3 Pole Thermal relay type RTX3 150A for Star Delta starter of Cap 150 HP thermal over Load relay ranging from 160 A to 240 Amps Make Make As per existing

Replacement of unserviceable Thermal relay with 3 Pole Thermal relay type RTX3 100A for Star Delta starter of Cap 60 HP thermal over Load relay ranging from 90A to 150 Amps Make Make As per existing

Replacement of unserviceable Thermal relay with 3 Pole Thermal relay type RTX3 40A for Star Delta starter of Cap 12.5/10 HP thermal over Load relay ranging from 22 A to 32A Amps Make As per existing

M/L for repairing replacing the old corroded Base foundation structure with new made as per existing size of MS channel with cutting welding to the shape for 150/60 HP motor including necessary PCC work complete all as directed

M/L for replacing the old corroded Iron Vibrating pad 60/150 HP motors complete with Nut bolts including necessary PCC work complete all as directed

S/F Cast Iron Foot valve of size 80/100 mm including nut, bolts and washers suitable size as directed by Engr in charge.

S/F CI Foot valve of size 150 mm including nut, bolts and washers f suitable size as directed by Engr in charge.

Submersible cable 6 Sqmm 3 core and connecting with the pumping set motor carefully including taking down the existing cable complete all as specified

Submersible cable 4 Sqmm 3 core and connecting with the pumping set motor carefully including taking down the existing cable complete all as specified

M & labour for replacement of on load change over switch back to back type, in open execution, 4 Pole, 415 Volt, 50 Hz, Rating 400 Amp including provn of fixing aggrement in exesisting panel Make As per existing panel

S & F in replacement of Rubber gasket 6mm thick as per site requirment complete all as specified and directed.

S & F MS bolts and nuts for Pump Moter base plate different size as per site requirment including fixing arrangement at same location.

Taking proper shut down disconnecting all the electrical connection, dismantling the motor from the base plate and pump for transporting the same to repair wksp approved for winding dismantling the motor, cutting and removing the old heated up/burnt winding of the stator /rotor cleaning the slots and transportation back the same after winding and reassembling complete of electric motor 60 HP to 150 HP all as directed by Engr -in- Charge. Note :- (a) Rewinding of motor will be measured and paid separately under relevent item (b) The motor shall be squerrel cage induction/slipring induction motor. (c) The rates quoted shall be deemed to include the cost of loading/unloading, transportation, grease, nuts bolts and washers of any size and shape as required at site and refixing of serviceable motor duly functional and testing complete at tis existing location/position complete all as specified and directed. (d) The contractor shall be arranged a workshop visit of Engr-in-Charge for each job and cutting complete burnt winding of motor in presence of Engr-in-Charge.

Supply & Fixing in replacement of rotor bearing in motor DE and NDE of 60/150 HP as per site requirment complete all as specified and directed by Engr-in-Charge. Make : SKF (Original)/NBC

Rewinding the motor stator/roter with super enamelled copper winding wire of existing size and gauge and truns etc including all the insulating materials i.e varnish with suppr high quality of cotton tape insulating paper and other misc items of motor, capacity of motor 60 HP to 150 HP complete all as specified and directed by Engr-in-Charge. Make ATLAS/DEVIDYAL

Taking down old/unsv/burnt out motor for capacity of 10/12.5 HP, 3 phase 415 volts and rewinding & fixing of existing size of motor with supper enameled copper winding wire as per existing size and truns etc including all the insulating materials ie. varnish, cotton,tape, insulating paper and soldring etc, all as specified and directed by Engineer-in-Charge. Make Copper wire : ATLAS/DEVIDYAL

Taking down old/unsv/burnt out motor for capacity of 3/5 HP , 3 phase 415 volts and rewinding & fixing of existing size of motor with supper enameled copper winding wire as per existing size and truns etc including all the insulating materials ie. varnish, cotton,tape, insulating paper and soldring etc, all as specified and directed by Engineer-in-Charge.Make Copper wire : ATLAS/DEVIDYAL

Taking down old/unsv/burnt out motor for capacity of 1 HP to 2 HP, 3 phase 415 volts and rewinding & fixing of existing size of motor with supper enameled copper winding wire as per existing size and truns etc including all the insulating materials ie. varnish, cotton,tape, insulating paper and soldring etc, all as specified and directed by Engineer-in-Charge. Make Copper wire : ATLAS/DEVIDYAL

Taking out submersible pumping set complete alongwith pipe from the existing sump / bore well for repair and refixing the same on existing location after repair & making electric connection including tesing and commissioning complete and dismantling of submersible motor pump of capacity as under mention for repair.

Capacity 7.5 HP

Capacity 5.0 HP

Capacity 3.0 HP

Capacity 1.0 HP

M &L for rewinding the submersible moter vertical/horizental with supper enameled copper winding wire as per existing size and truns etc using best quality of insulating material of following size

Capacity 7.5 HP

Capacity 5.0 HP

Capacity 3.0 HP

Capacity 1.0 HP

M &L for repair of the submersible pump complete as per existing size material i.e emplller,bush,Thurst bearing, Thurst Plate & rod of following capacity

Capacity 7.0 HP

Capacity 5.0 HP

Capacity 3.0 HP

Capacity 1.0 HP

S & F in repair bearing suitable for following capacity of pumping set make NBC / SKF

10/12.5 HP motor

5 HP motor

3 HP motor

Supply and fix in reapir coupling bolts and nuts for following pumping sets:-

150 HP Pumping Set

60 HP Pumping Set

Supply and fix in reapir only coupling's rubber bush make as per existing for following pumping sets:

150 HP Pumping Set

60 HP Pumping Set

Taking out old unserviceable Scada UPS battery and S & F new storage type maint free lead acid APCRCB battery 9AH/12V (set of two Battery total 24 V) heavy duty, initial charged and testing after connecting complete upto the entire satisfication complete all as specified and directed. Make :- As per existing

Disconnecting and taking out unserviceable horizontaly split casing centrifugal pump sets single suction capacity 60 to 150 HP from inposition by means of chain pully block, loading the same in transport and transporation to local workshop at Ajmer for repair works, including dismantling the pump at workshop and replacing the defective/worn out parts including all meteling works, boring inside pump and reassembling the same after carried out all repair works and taking back to the pump house including installation, testing and commissioning complete for satisfactory performance all as directed by Engr-in-Charge. Note :- Spare parts shall be measured and paid separately under relevant items.

Taking out defective parts at same place and replace with new parts for pumps of any capacity 60 HP to 150 HP multistage centrifugal pump following ;- ( Note :- as per manufacturer compositon). Make : As per existing

cast iron impeller 1st stage / 2nd stage including lock pin for any cap 150 HP

cast iron impeller 1st stage / 2nd stage including lock pin for any cap 60 HP

Cast Iron shaft sleeves for any cap 60 HP to 150 HP

Cast Iron Neck Ring complete set for Impeller for any cap 60 HP to 150 HP

Cast Iron Impeller Separating Ring Set for any cap 60 HP to 150 HP

Mild steel pump shaft with keys and rear check nut for any cap 60 HP to 150 HP

Pump shaft bearing NDE/DE 60/150 HP Pump

Gland Cup complete with nut & bolt any cap 60 HP to 150 HP

Repair to pump , suitable casting for fitting of bearing with shaft including suitable ring etc.

Tyre coupling assembly complete with nut and bolt size as per ground requirment for capacity 10 HP to 150 HP

S&F in replacement Cast Iron Non return valve, suitable for 150 mm bore pipe, heavy duty ,both end flanged of pressure rating PN 1.6 and jointing with rubber or fibre board gasket complete with and including nuts, bolts and washers complete all as specified and directed. Make:- Kirloskar/Leader/L&T

S&F in replacement Cast Iron Non return valve, suitable for 100 mm bore pipe, heavy duty ,both end flanged of pressure rating PN 1.6 and jointing with rubber or fibre board gasket complete with and including nuts, bolts and washers complete all as specified and directed. Make:- Kirloskar/Leader/L&T

S&F in replacement Cast Iron Non return valve, suitable for 80 mm bore pipe, heavy duty ,both end flanged of pressure rating PN 1.6 and jointing with rubber or fibre board gasket complete with and including nuts, bolts and washers complete all as specified and directed . Make:- Kirloskar/Leader/L&T

M&L for collection of water sample from the Rajmahal Pump House and STP area getting then tested from approved Govt laboratory (approved by GE) & furnishing test report indicating chemical and bacteriological analysis on monthly basis including presence of fluorine contents if any all as directed by Engineer-in-Charge.

Recharge of SCADA panel data sim (Airtel/Vodafone) for smooth functioning automation system on monthly/quarterly/six monthly basis complete as directed by Engineer-in-Charge

M/s SUNIL ENTERPRISES

PD GUPTA AND COMPANY