IUDM 2018-19 and 15th CFC tied and untied

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete 10 cum. a) Footings

Grade Beam

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification. TWAD 23 -24 Pg No - 324a) Collection well 1st Depth 0 m - 2 m

Collection well 2nd Depth 2 m - 4 m

Removal of Excavated Excess Earth away from the site to 5K.M including loading and transportation charges etc, complete as per standard specification. For 1M3 TWAD 23 -24 Pg No - 334

Refilling with excavated earth with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers well rammed, watered and consolidated etc. complete complying with standard specification TWAD 23 -24 Pg No - 298

Cement Concrete 1:4:8 (One Cement, Four sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed by using mechanical earth rammer, consolidated and curing etc. complete complying with standard specification and as directed by engineer in charge

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)a) Base Slab & Tie beam

Beam and Slab

Column

Providing and Iaying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20 mm and down graded hard broken granite, stone jelly for all RCC items of works with minimum SRC cement content of 400 kg/m³ and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 m³) 7730 Kg. of 20 mm machine crushed stone jelly and with about (3.3 m³) 5156 kg. of 10 - 12 mm machine crushed stone jelly and with about (4.79 m³) 7670 Kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra, etc complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards.(Sl.No:39.a) Upto Basement

Ground floor

parapet

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.TNBP-spl

Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309)

Supply and filling of cinder material thickness of best approved quality as per standard specification

Supply and delivery of following sizes of FRC Manhole Covers With Frames to stores on as per IS 12592:2002 to its latest revisionwith reinforcement details for covers and frames TWAD 23 -24 Pg No - 88a) 600mm dia FRC manhole frame with Cover

450mm dia FRC manhole frame with Cover

Brick work in CM 1:5 (one cement & five sand) using II class ground moulded bricks of size 8.75"X4.25"X 2 3/4" including finishing, curing, etc., complete complying with standard specification - 100CFTa) Upto Basement

Ground floor

First floor

Manufacturing, supplying and fixing precast reinforced cement concrete slabs of following thickness in RCC M20 concrete using following HBGS jelly excluding cost of reinforcment steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in positon in al floors etc., complete complying with standard specification and as directed. 75mm thick slab (using 20mm HBGS Jelly)

Providing and constructing precast concrete solid blocks with compresive strength not less than 35 Kg per sqm with cement mortar 1:4 masonry with soild blocks of 40x 20x 20 cms conforming to IS 2185/1965 in super structure including the cost of materials, labour charges, scaffolding, curing complete as per specification

Providing and fixing uPVC pipes (Soil and waste line) of required diameter conforming to I.S.-13592, and I.S.-4985 to withstand continous internal hydroulic pressure of 6 kg/cm2 including necessary fixtures and fittings, such as bends, tees, single junctions, double junctions and joining with rubber rings and lubricants, on wall by means of clips or in ground including necessary excavation, laying refilling, trench testing etc. complete. (Prior approval of sample and brand by Engineer in charge is necessary before use.)a) 110 mm PVC pipe

160 mm PVC pipe

110 mm PVC preforated pipes

110 mm dia UPVC-Tees fixing

110 mm dia Elbow pipe- UPVC

Plain Cement Concrete 1:2:4 (one cement, three fine aggregates and six coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Planting of Canna indica varigated Plantfoliage shrub variety of height 30-45 cmin polythene bag of dia 20 cm includingloading and unloading charges,transportation, stacking of saplings atsite, earth work excavation of requiredsize, planting of sapling, refilling ofexcavated earth etc as directed by thesite in-charge.

Providing and Laying coarse stone aggregates/river pebbles of sizes as below after washing and sieving to make it free from fines and dusta) 90-120mm

Supplying of polished cuddapah slab of 20/30 mm thickness including laying to correct alignment as direct by engineer in charge. Includes fixing the slab to support structures.

Supply and Filling of Brickbat 40mm (Brick Jelly) including Labour charges etc, complete as per standard specification

Fabricating supplying and fixing of roof with Poly carbonate sheet of 6mm thcik with any colour or any other approved design and to be fixed with shelf tapping screws, plastic washer. The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmen

Delivery piping arrangement including NRV WAFER TYPE (DUAL PLATE CHECK VALVE), & SV Supply and delivery of DI D/F Gate sluice valves (soft seated) resilient seated soft sealing Gate Valves(Sluice Valves) with body Bonnet of Ductile cast iron of Grade GGG 40 or equivalent grade, Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 O- Ring protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI14846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and out side with pocket less straight through body passage. All the valves are to be compatible for buried application with pressure rating PN 10/16 and with 5 years warranty complete TWAD 23 -24 Pg No - 72, 74

Supply and fixing of 250MM Non Return Valve including of all cost of material and cost of conveyance and ect..

Supply and delivery of sewage Sludge Cutter pump set conforming to IS 14220 /2002 and asamended thereafter and BEE 3 Star Rated capable of discharging the following duties due toall causes. The pump shall be with stainless steel shaft and dynamically balanced bronzemixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rodas per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints.The non-return valve located at the top of the pump in the discharge outlet connection is tobe designed with minimum friction. The pump should be directly coupled to 2880 RPM, threephase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOLupto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter forabove 20 HP starting and for continuous operation. Twad 23-24 pg 109

Supply and delivery of Submergible pump set conforming to IS 14220 /2002 and asamended thereafter and BEE 3 Star Rated capable of discharging the following duties due toall causes. The pump shall be with stainless steel shaft and dynamically balanced bronzemixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rodas per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints.The non-return valve located at the top of the pump in the discharge outlet connection is tobe designed with minimum friction. The pump should be directly coupled to 2880 RPM, threephase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOLupto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter forabove 20 HP starting and for continuous operation. Twad 23-24 pg 109

Providing the following tools mounted on Teak wood Board to be fixed on the wall the rates are inclusive all taxes , duties and handling charges F.OR destination etc., complete TWAD 23 -24 Pg No - 132a) 6" chain wrench best India make. - 1 No.

8" chain wrench best India make. - 1 No.

Connector screw driver 901 Taperia make -1 No.

200mm screw driver 825 Taperia make - 1 No

300mm screw driver 829 Taperia make - 1 No.

400mm screw driver 930 Taperia make - 1 No

200mm cutting player taperia make - 1 No.

800gm ball pan Hammer with Hardle tapria make

15" screw spanner tapria make - 1 No.

12" bearing puller - 1 No.

Lever type grease gun - 1 No.

12" screw spanner - 1 No.

Crow Bar 5" - 1 No.

Hacksaw frame with Block - 1 No.

DE spanner set 6 mm to 32mm Jhalani make - 1 set.

Rings spanners set 6mm to 32mm Jalani make - 1 set.

24" pipe wrench - Jalani make - 1 No.

14" pipe wrench - Jalani make - 1 No.

Supplying, fixing, testing, commissioning tamper proof LT metering cubicle with suitable rating CTs, bus bar, fuse cut as per TNEB specification for accomodating 1 No. Energy meter supplied by TNEB including provision of 63 amps fuse units - 3 Nos. TWAD 23 -24 Pg No - 139

Supply and delivery of Fully Automatic Auto Transformer Starter suitable for the motor offered.Floor mounting type air/ oil cooled Auto Transformer Starter with tapings at 50%, 65%, 80%,housed in robust steel chamber with arc and main contacts confirming to IS 8544 Part IV and asamended therafter for operation in AC three Phase 50 Hz (+/- 5%), 415V (+/- 10%) with thefollowing components, under voltage release with no volt coil, over load relay with dash potarrangements, single phasing preventor, LED ON/ OFF switches, Mounted Ammeter, Earthleakage relay, contactor assembly suitable for next standard KW rating, in coming and out goingcable entry provisions, transformer tank including first filling of oil etc.

Supplying of PVC insulated and PVC sheathed steel armoured cable with aluminium conductor of following size to be laid (conforming to ISS 1554.) TWAD 23 -24 Pg No - 124a) 3 C x 35 Sqmm (Aluminium) to be laid below GL from EB point to meter Box

3 C x 16 Sqmm (Aluminium) to be laid below GL from MDB to pumps through starter panel and also from MDB to SDB for lighting.a) Cables , DB Box to Lamp posts

3 C x 10 Sqmm (Aluminium) to be laid below GL from MDB to capacitors

Laying of above Aluminium cable below GL including earth work excavation and refilling the trench after the cable laid etc., complete From( EB to MDB) Upto 95 SQM TWAD 23 -24 Pg No - 126

Laying of cables in trench inside pump room (motor and lighting) Upto 95 SQM

Jointing the cable including cost of jointing materials, lugs, clamps etc complete. TWAD 23 -24 Pg No - 125a) 35 Sqmm (Aluminium) (From TNEB Panel to MDB and From DG Set to MDB)

16 Sqmm (Aluminium) to be laid below GL from MDB to pumps through starter panel and also from MDB to SDB for lighting.

10 Sqmm (Aluminium) to be laid below GL from MDB to capacitors

Erection and commissioning of non clog Submersible pumpsets including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps,pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches ,starters ,voltmeter, Ammeter, three pilot ( indicating ) lamps,capacitor,single phasing preventor,water level guard and laying and jointing the cables and twin earthing as per IE rules etc.,complete and testing the pumpset and trail run for 10 days etc., complete TWAD 23 -24 Pg No - 320

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitablePVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting ofsuitable colour for open PVC light point / fan point (for electronic regulator) (5 points per coil) SD 18

Supply and fixing of 4'40W twin box type fluorescent fitting complete with copper choke and condensor with TWround block on wall or ceiling with tubes and PVC unsheathed copper leads from terminal to the fitting with fluoresent tubes SD 90

Supplying and Fixing 3 pin type , combined 15 Amps flush type socket and a 15 Amps SP switch surface mounting in a 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required. Three way plug. Complete as directed by Engineer. TWAD 23 -24 Pg No - 219

Supplying and fixing 32 A DP swicth with metal clad handle for street light control TWAD 23 -24 Pg No - 214

Supplying , fixing and wiring earth electrode as per IS:3043 for grounding all equipments using 40mm dia, 2.9mm thick GI pipe 2.5m long buried in a pit with GI funnel with mesh and suitable size reducer fixed on top of the earth electrode. The funnel should be enclosed in a CC chamber300X300X300mm size with a cast iron cover. The pit should be filled with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduit etc., is to be established through GI wire/ strip of size as per IS specification 732.using 12mm dia bolts, nuts, washers and checknuts etc. The pipe shall have 16 through holes of 12mm dia.(TWIN EARTHING) TWAD 23 -24 Pg No - 135

Supply erection of 8mm free standing double arm bracket8 sided octogonally continously tapered structured polewith base plate of size 300x300x12mm as per IS 875with following specifications.Bottom pole dia - 130mmTop Pole Dia - 70mmThickness of pole - 3mmThe pole should be hot tip galvanized confirming to BESNISO 1461 with thickness of 65 micron TWAD 23 -24 Pg No - 238

Supply and delivery of fixing 30W LED Street light fitting with LED including cost & material and all Charges etc... TWAD 23 -24 Pg No - 206

e. 5 Amps switchs for lights (Flush type) TWAD 23 -24 Pg No - 210

Obtaining power supply including cost of 20mmGI pipe, Specials, EB Meter Board, Aria fuse with Board, GI Wire for stay and earthing, 20mm GI pipe for earthing and cable encasing including civil works engaging "B" License holder etc completed for TNEB Sera) Supply delivery and fixing of MCB Isolator 40 A FP with ISI make ( for main ) TWAD 23 -24 Pg No - 223

(vii) 20mm GI pipe for twin earthing and cable encasing TWAD 23 -24 Pg No - 41

(viii) 4 way nutral link SD 125 A)

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Plastering with cement mortar 1:5 (One cement and five sand) ,12 mm ,thick in all floors including cost and conveyance of all materials to site etc,complete as per standard specifications (S.I.306)

White washing two coats with freshly burnt shell lime white in all floors including cost of lime and other materials brushes scaffolding charges etc, complete as per standard specification

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Providing granolithic floor finish of 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed sand (M-Sand) and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Windows of casement type (open) from theprofile the size of outer frame 60mm x 58mm andshutter profile are reinforcement with GI/1mm 125GSMand 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDMrubber (black colour) covered with over all the edges offrame and shutter the shutter will be provided withEspag multi power point locks and also it operates ashandle. The corners and joints should be welded andcleaned. Radiations free pin headed plain or browncolour glass 4mm thick should be provided to theshutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash andouter frame that enables opening of the window. The window should be fixed to the wall with 100% packingwith screws and silicon packing all round the frames. The window should be got approved from the ExecutiveEngineer before use on work.TWAD 23-24 Pg.No 188

Painting two coats over the new iron work with Ready Mixed Enamel Paint of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supply and fixing of M.S.Grills with doors and windows with one coat of red oxide with primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc, complete as per standard specifications

Supplying and erecting pull and push gear type rolling shutter with I.S.I. make of approved size and section using 18 gauge G.I.sheet with manually operated type. The Shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc, complete as per standard specification. TWAD 23-24 Pg.NO 165

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). etc, complete as per standard specifications.SD 23

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.etc, complete as per standard specifications SD 38

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.etc, complete as per standard specifications SD 54

Supply and fixing of 20W 4 Feet LED Fitting with LED

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work. etc, complete as per standard specifications SD 234

Supply and fixing of 3 phase 4 wire 4 way ICDB of 32 A per way with 100 A TPN MC switch with suitable trunking box Ms cable entry boxes and internal connection on suitable angle iron frame work with earth connection etc, complete as per standard specifications SD. 175

BOREWELL at 120 m Depth Including Motor and Pipe and All other Fittings & cost of material and conveyance etc..

Supply and fixing of Horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure with 40 A 4 pole MCB isolater as incoming and 12 Nos. 6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark etc, complete as per standard specifications SD.179

Supply and fixing of 1400mm sweep (56") AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod on the existing clamp SD 109

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m etc, complete as per standard specifications SD.75

Supply and run of 4 X 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade on 7/20 Gl bearer wire for service connection mains etc, complete as per standard specifications.SD 68

Genset 82.5KWA

Add GST 18%