Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹70.3 LAccepted-AOC HOUSE NO 6 18 WARD NO 05 HOUSING BOARD COLONY HANUMANGARH JN 335512 RAJ | HANUMANGARH | RAJASTHAN | 335512 | ₹70.3 L | L1 | Accepted-AOC L1 Bidder |
| 2 | L2₹85.2 LRejected-Finance C O GENERAL DAIRY VILLAGE BARAGAON SRI GANGANAGAR 335 001 | GANGANAGAR | RAJASTHAN | 335001 | ₹85.2 L | L2 | Rejected-Finance Not the lowest Bidder |
| 3 | L3₹86.0 LRejected-Finance | ₹86.0 L | L3 | Rejected-Finance Not the lowest Bidder |
| 4 | L4₹86.4 LRejected-Finance 129 STREET NO 3 3 GREEN AVENUE BIBI WALA ROAD BATHINDA 151001 | BATHINDA | BATHINDA | PUNJAB | 151001 | ₹86.4 L | L4 | Rejected-Finance Not the lowest Bidder |
| 5 | L5₹87.3 LRejected-Finance | ₹87.3 L | L5 | Rejected-Finance Not the lowest Bidder |
| Sl No | Description | Qty | Unit | PAREEK AND COMPANY L2 | AYUSH BUILDERS L3 | KHANNA CONSTRUCTIONS L6 | Dashmesh Construction Company L5 | KULWANT RAI L4 | R B INFRABUILDERS L1 | Aggarwal Brothers and company L7 |
|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, complete all as specified and directed by Engineer-in-Charge. | 1,400 | Sqm | 20 ₹28,000 | 30 ₹42,000 | 20 ₹28,000 | 50 ₹70,000 | 37 ₹51,800 | 30 ₹42,000 | 20 ₹28,000 |
| 2.00 | Demolition of mud or any form of soil in roof, any depth including plastering and leaping (where full thickness removed disposal off rubbish upto a distance n.exc 100m, where directed complete all as specified and directed by Engineer-in-Charge. | 210 | Cum | 100 ₹21,000 | 250 ₹52,500 | 120 ₹25,200 | 80 ₹16,800 | 267 ₹56,070 | 150 ₹31,500 | 100 ₹21,000 |
| 3.00 | Demolition of Cement concrete (unreinforced) of any description and in any position/old existing felt/plaster/tiles etc including removal of demolished matrial out of defence land complete all as specified and directed by Engineer-in-Charge. | 70 | Cum | 100 ₹7,000 | 250 ₹17,500 | 500 ₹35,000 | 200 ₹14,000 | 297 ₹20,790 | 150 ₹10,500 | 100 ₹7,000 |
| 4.00 | M&L for levelling course for roof slab, PCC type B0,1:2:4(12.2mm graded aggragate) using waterproofing compound (SBR) for maintaining proper roof slope and finishing sirface even and smooth without using extra cement complete all as specified .(Minimum thickness of concrete should not be less than 50mm at any point) complete all as specified and directed by Engineer-in-Charge.
Note:- Waterproofing compound should be measured and paid seperately. | 70 | Cum | 3,200 ₹2.2 L | 5,500 ₹3.9 L | 5,000 ₹3.5 L | 5,000 ₹3.5 L | 3,967 ₹2.8 L | 3,100 ₹2.2 L | 3,500 ₹2.5 L |
| 5.00 | Supply of SBR waterproofing compound @ 2% of per Kg cement used complete all as specified and directed by Engineer-in-Charge.
Make:- Fosroc / Sika/ Choksey / Chemsol / Bostik/ STP | 431.94 | Kg | 100 ₹43,194 | 225 ₹97,186.50 | 220 ₹95,026.80 | 150 ₹64,791 | 157 ₹67,814.58 | 60 ₹25,916.40 | 100 ₹43,194 |
| 6.00 | OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm.
(a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification.
(b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry.
(c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller.
Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger Paints
Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat.
(ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE.
(iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years. | 1,500 | Sqm | 600 ₹9 L | 550 ₹8.3 L | 550 ₹8.3 L | 720 ₹10.8 L | 647 ₹9.7 L | 430 ₹6.5 L | 600 ₹9 L |
| 7.00 | M & L for making benching with PCC (1:2:4) type B0 using WPC along side wall adjoining to roof in concave shape complete all as specified and directed by Engineer-in-Charge. | 7.85 | Cum | 4,000 ₹31,400 | 5,500 ₹43,175 | 4,500 ₹35,325 | 4,950 ₹38,857.50 | 4,987 ₹39,147.95 | 3,000 ₹23,550 | 3,500 ₹27,475 |
| 8.00 | Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site complete all as specified and directed by Engineer-in-Charge. | 35 | Each | 150 ₹5,250 | 50 ₹1,750 | 80 ₹2,800 | 25 ₹875 | 107 ₹3,745 | 50 ₹1,750 | 50 ₹1,750 |
| 9.00 | Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge. | 65 | Each | 150 ₹9,750 | 70 ₹4,550 | 80 ₹5,200 | 25 ₹1,625 | 107 ₹6,955 | 50 ₹3,250 | 50 ₹3,250 |
| 10.00 | Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and removal complete all as specified and directed by Engineer-in-Charge. | 2 | Per Leaf | 100 ₹200 | 50 ₹100 | 80 ₹160 | 25 ₹50 | 107 ₹214 | 50 ₹100 | 50 ₹100 |
Updated dates
Tender Value
Refer Docs
EMD Value
₹1.7 L
Closing Date
10 Feb 2026, 6:00 pmClosed
HQ CWE SRI GANGANAGAR
HQ CWE POST BOX 48 SRI GANGANAGAR-335001 (Rajasthan)
SPECIAL REPAIR TO BLDG NO. P-1231 (WORKERS AMENITY ROOM), P-1257 (DRYING AND IRONING STORE (WASHER MAN SHOP), P-1228 (QM STORES), P-1246 AND P-1251 (STOCKING WING) OF 16 RAPID ORD UNIT AT SRI GANGANAGAR MIL STN
2026_MES_748288_1
CA NO CWE SGNR/TOKEN-104 OF 2025-26
Open Tender
Civil Works
180 days
GE SRI GANGANAGAR
As per NIT
8 documents required · 8 mandatory
₹1,000
GE SRI GANGANAGAR
₹1.7 L
Yes
23 Mar 2026
13 Jan 2026
11 Feb 2026
13 Jan 2026
10 Feb 2026
27 Jan 2026
Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, complete all as specified and directed by Engineer-in-Charge.
Demolition of mud or any form of soil in roof, any depth including plastering and leaping (where full thickness removed disposal off rubbish upto a distance n.exc 100m, where directed complete all as specified and directed by Engineer-in-Charge.
Demolition of Cement concrete (unreinforced) of any description and in any position/old existing felt/plaster/tiles etc including removal of demolished matrial out of defence land complete all as specified and directed by Engineer-in-Charge.
M&L for levelling course for roof slab, PCC type B0,1:2:4(12.2mm graded aggragate) using waterproofing compound (SBR) for maintaining proper roof slope and finishing sirface even and smooth without using extra cement complete all as specified .(Minimum thickness of concrete should not be less than 50mm at any point) complete all as specified and directed by Engineer-in-Charge. Note:- Waterproofing compound should be measured and paid seperately.
Supply of SBR waterproofing compound @ 2% of per Kg cement used complete all as specified and directed by Engineer-in-Charge. Make:- Fosroc / Sika/ Choksey / Chemsol / Bostik/ STP
OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm. (a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification. (b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger Paints Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years.
M & L for making benching with PCC (1:2:4) type B0 using WPC along side wall adjoining to roof in concave shape complete all as specified and directed by Engineer-in-Charge.
Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site complete all as specified and directed by Engineer-in-Charge.
Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.
Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and removal complete all as specified and directed by Engineer-in-Charge.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge including S & F following items: - (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finished sliding door bolt 300mm -01 Nos per leaf (e)Stainless steel (304 grade ) finished floor door stopper -01 Nos per leaf Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/guage skeleton door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws,including s&f of stainless steel steel 304 grade (natural finish) wire cloth , all as per direction of Engineer-In-Charge including S&F following items: (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finishedsliding door bolt 300mm -01 Nos per leaf (e)stainless steel (304 grade) finished floor door stopper -01 Nos per leaf(f) stainless steel (304 grade) wire cloth fixing as per manufacture. Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.
Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. for fixing MosquitoMesh and XTN aluminium mesh combinely panel area of door except stiles and rails to be panelled wire mesh with self tapping rpund headed screws at requrd distance, scres and edge covered with feathered pvc edge beading all around mesh and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer in- Charge including S & F following items: - (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250mm - 1 nos per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.
S & F factory made uPVC sliding window three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) with or without provision of opening for cooler as directed including all fittings, steel roller system, locking arrangement etc., making arrangement for fixing of hardware, glass, wiremesh, grill etc all as per manufacture instruction and Drg No BTD-890/R . Note:- The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly .Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be deemed to be included Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.
S & F factory made uPVC window or ventilator side hung/top hung (glazed and gauge both) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) including all fittings like hinges, tower blot, peg stay, locking arrangement etc., making arrangement for fixing of hardware all as per manufacture instruction and Drg No BTD-890/R all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly. Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be deemed to be include. Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.
M & L toughned glass 6mm thick cutting to shape, drilling holes and fixed to steel, metal or wooden window frames complete all as specified and directed by Engineer-in-Charge.
S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified and directed by Engineer-in-Charge.
S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified and directed by Engineer-in-Charge.
M & L sheet Pin headed glass 4.0mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified and directed by Engineer-in-Charge.
Dismentling of boarding any description fixed in any position with nails/ screws complete all as specified and directed by Engineer-in-Charge.
M&L for providing Cupboard with shutters in required sizes &shape at site made out of HDHMR Board,18/19mm thick, density over 850kg/cum,having a classA fire rating,grade2 quality, commercial type, fixed with srews to timber frame work as in kitechen cupboard shutter/shelves/cabinet etc consisting of both side 0.9mm laminate one side decorative& other side plain. The panels shall be fabricated using adhesive and screws where ever required all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edges bent finsh as per manufacturer instruction and complete all as specified and directed by Engr-in-charge.
S&F second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engineer-in-Charge.
S&F continuous (piano) hinges 20mm & 12 MM width of flap, mild steel bright finish or electro galvanised complete all as specified and directed by Engineer-in-Charge.
S & F hasp and staple, safety type of aluminium anodised100mm size fixed with screw complete all as specified and directed by Engineer - in - Charge.
S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete all as specified and directed by Engineer-in-Charge.
S&F stainless steel handles, 150 mm long complete all as specified and directed. (back plate staple D type) complete all as specified and directed by Engineer-in-Charge.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.
M&L for 25 thick cement concrete flooring type B-0 1:2:4 (12.5 mm graded stone aggregate) complete all as specified and directed by Engineer-in-Charge.
M&L for vitrified Double charged/Ultracharged ceremic tiles (square / rectangular) area of each tile (size 1200 X 600mm) exceeding 0.42sqm but not exceeding 1.0 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish even & faircomplete all as specified and directed by Engineer - in - Charge.
All as per Srl item No. 32.0 here in before but on vertical surfaces/skirting dados etc over 10mm rendering in CM 1:4 finished even and fair, complete all as specified and directed by Engineer - in - Charge.
M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering.
M&L for anti-skid ceramic joint free premium quality coloured tiles 400 X 400 mm and 6-7 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.
Dismantling stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.
M&L for granite (of any type) 20 mm thick machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, rounding of edges (moulding of edges) and polishing complete laid over 15 mm thick screed bed in CM 1:4 etc all as specified and directed by Engineer in charge.
M & L Green Marble work 14 to 16mm thick (table moulded and mirror polished), area of each slab not less than 0.72 Sqm in Floors, Cooking platforms, Window cills, Top of pillars trads of steps etc including 15mm thick screed bed in cement mortar 1:6 including pointing in cement using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engr-in-Charge. Note : 1. Green marble for Window cills, top of pillars and treads of steps should be single peace upto 1.2m length of rquired width. 2. White marble border for green marble flooring of required size shall be provided and it would be measured and paid as in flooring area of above item.
M&L for Green marble work 14 to 16 mm thick table moulded and mirror polished) in skirting on verticle surfaces as jambs of door/windows, jambs of Pillars, riser of steps etc including 10mm thick backing coat in cement mortor 1:4 including pointing in cement using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engineer-in-Charge. Note : Green marble for window jambs, pillar jambs, Riser of steps would be single piece upto 1.2m length of required width.
M&L 40 mm GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as specified and directed by Engineer-in-Charge.
Demolition of RCC of any description such as Kitchen chimney, chajja, shelves, OHT Tanks. etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition)
M&L for reinforced nominal mix cement concrete type B1 1:2:4 (20 mm graded stone aggregate) as in Slab supported on walls for tank staging and in shelves and etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-charge
M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.
Use and waste of form work torough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick complete all as specified and directed by Engineer-in-Charge.
Use and waste of Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by Engineer-in- charge.
Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc.complete all as specified and directed by Engineer-in-Charge.
M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.
M&L for rendering 15 mm thick in cement mortar 1:4 (10mm thick rendering in first layer and 5 mm thick rendering in second layer)on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.
Supply only integral water proofing compound, ISI Marked complete all as specified and directed by Engineer-in-Charge.
M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.
M&L for prepration of New plastered Internal wall surface complete and applying the following :- (a) Applying two coat 1.5 mm wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified (c) Applying two coat of interior Premium Emulsion Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible
M&L for prepration of New plastered External wall surface complete and applying the following :- (a) Applying two coat 1.5 mm wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified (c) Applying two coat of Exterior Emulsion using Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible
M&L for prepration of New plastered ceiling surface complete applying the following :- (a) M&L 1.5 mm wall care putty in two coats on ceiling surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of interior acrylic emulsion over a coat of chalk whitening priming by using Airless spray / Roller over complete all as specified .
M&L for complete removal of existing treatment for internal wall surfaces including filling depression of scraped surface (a) Applying one coat 1.5mm wall care putty on old internal wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified (c) Applying two coat of interior Premium Emulsion Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible
M&L for complete removal of existing treatment including filling depression of scraped surface with 1.5mm wall care putty in one coat on old ceiling surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as specified and directed complete and applying two coat of interior acrylic emulsion of approved tint over a coat of primer on old prepared surface by using Airless spray / Roller over complete all as specified and directed by Engineer-in-Charge.
M&L for complete removal of existing treatment including filling depression of scraped surface on Old external wall surfaces (a) Applying one coat 1.5 mm wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified (c) Applying two coat of Exterior Emulsion using Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible
M&L two coats of synthetic enamel exc 10 cm width /girth on OLD steel surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.
M&L two coats of synthetic enamel over a coat of red oxide primer exc 10 cm width /girth on new steel surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.
M&L two coats of synthetic enamel exc 10 cm width /girth on OLD wooden surfaces including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.
Material and labour for repair of chajja facia using cement mortar (1:3) n.exc 300 mm girth finishing the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.
M&L for Obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work etc complete all as specified and directed by Engineer - in - Charge.
M&L for Writing letters or figures with fluorecent paint ( Block. Roman, Italic or Indian) n exc. 30 cm high etc complete all as specified and directed by Engineer - in - Charge.
Dismantling of brickwork built in cement mortar of any description complete all as specified and directed as per Engineer-In-Charge
M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in CM 1:6 etc.complete all as specified and directed by Engineer - in - Charge.
M&L half brick work with sub class B bricks straight or curved on plan to any radius in CM 1:4 etc.complete all as specified and directed by Engineer - in - Charge.
Dismantling and disconnecting existing CI soil waste/vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed by Engineer-in-Charge.
Dismantling and disconnecting of existing CI soil waste/vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed by Engineer-in-Charge.
Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store(measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.
Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant including beds, socket, Y junction , Tee, cowl etc complete all as specified and as directed by Engineer-in- charge. Complete including low carbon steel material with hot dip zinc aluminium flake coated and fixed all . Note:- Details of pipe supporting system in all as per Drg No-BTD -916 ). Note: uPVC PIPE AND FITTING/ FIXTURE (i) The testing for leakage of pipe shall be done before connecting the pipes(ii) All pipes shall be minimum 4'' away from wall fixed with GI bracket (iii) The gully trap shall be minimum 90cm away from walls (iv) Separates pipes for each floor should be provided (v) Swage and drain system shall be separate.
Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant including bends, socket, Y junction , Tee, cowl etc complete all as specified and as directed by Engineer-in- charge. Complete including low carbon steel material with hot dip zinc aluminium flake coated and fixed all. Note: Details of pipe supporting system in all as per Drg No-BTD -916). Note: uPVC PIPE AND FITTING/ FIXTURE (i) The testing for leakage of pipe shall be done before connecting the pipes(ii) All pipes shall be minimum 4'' away from wall fixed with GI bracket (iii) The gully trap shall be minimum 90cm away from walls (iv) Separates pipes for each floor should be provided (v) Sewage and drain system shall be separate.
Supply & fixing 110mm uPVC pipes grade 'B' bends / Elbow heavy grade of any radius/shoe with or without access door fixed to uPVC pipes complete all as specified and directed by Engineer-in-Charge.
Supply & fixing 75mm uPVC pipes grade 'B' bends / Elbow heavy grade of any radius/shoe with or without access door fixed to uPVC pipes complete all as specified and directed by Engineer-in-Charge.
Supply & fixing in repair uPVC 75mm dia of floor trap with grating including jointing to waste pipes fixed in cement concrete 1:2:4 type B1 complete all as specified and directed by Engineer-in-Charge.
Supply & fixing uPVC pipes grade 'B' branch piece, (single Y ), 75mm bore (equal or unequal), with or without access to door complete all as specified and directed by Engr-in-charge.
Supply & fixing uPVC pipes grade 'B' branch piece, (single Y ), 110mm bore (equal or unequal), with or without access to door complete all as specified and directed by Engr-in-charge.
Supply & fixing in repair uPVC pipes grade 'B' vent cowl 110mm complete all as specified and as directed by Engineer-in- charge.
Supply & fixing salt- glazed stoneware gully traps 150x150 mm , square/roung mouth, p type complete all as specified and as directed by Engineer-in- charge.
Supplying and laying of 20mm (outer dia) (15mm inner dia) cpvc pipes SDR 11 & plain CPVC SDR 11 bend fittings on wall/ ceilings or laying in floors & including cpvc coated brass elbow, T, Male/ Female brass threaded adaptor etc. also including Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engr-in-charge.
M & L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. In brick walls.
S & F of 25mm (outer dia) (20mm inner dia) cpvc pipes SDR 11 & plain CPVC SDR 11 bend fittings on wall/ ceilings or laying in floors & including cpvc coated brass elbow, T, Male/ Female brass threaded adaptor etc. also including Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engr-in-charge.
M & L Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n.exc one brick complete all as specified and directed by Engineer-in-Charge.
S & F framed work such as grills, grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290 – Gde – 165 complete all as specified and directed by Engineer-in-Charge.
Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.
M & L PCC (1:3:6) type C-2 (using 40mm graded agg) 75mm thick as in plinth protection .complete all as specified and directed by Engineer-in-Charge.
M&L for 50 mm thick cement concrete , 1:4:8 type D2 (Using 40mm graded stone aggregate) flooring,paving etc. concrete complete all as specified and directed by Engineer-in-Charge.
M&L for Machine pressed Precast cement concrete interlocking coloured ( glossy finished / ruberised paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with and including 25mm thick sand cushining complete all as specified and directed by Engr-in-charge.
M&L for 30 cm x 30 cm x (20 to 25) mm thick machine pressed chequered cement concrete tiles(rubber moulded) set jointed and pointed in neat cement slurry in floors with grey cement including 15mm thick screed in CM 1:6 with pigments complete all as specified and directed by Engineer-in-Charge.
S & F factory made kerb stone of M-25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed.
Dismantling water tanks of any description exc 250 and n.exc 1000 ltrs capacityand removal from site complete all as specified and directed by Engineer-in-Charge.
S&F rotational moulded polyethylene water storage tank 1000 ltrs capacity three layered (Cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore PTMT ball valve, high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule (minimum weight 455gms) complete all as specified and directed by Engineer - in - Charge.
S&F 25 mm bore gate valve with handle, screwed both ends for inlet & outlet pipe and fixed complete all as specified and directed by Engineer-in-Charge.
S& F single lever High flow divertor consisting of exposed part kit with operating lever , wall flange & button and concealed body ,cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure complete all as specified and directed by Engineer-in-Charge.
S&F 15mm bore Long body bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer-in-Charge.
S&F CP angle valve for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type fixed as in repair complete all as specified and directed by Engineer-in-Charge.
S&F in repairs wall hung Vitreous china premium/1st quality wash down water closet with P trap WHITE / IVORY / Off White including connection to drain (or outgoing pipe) and to flushing pipe , anti syphonage pipe etc and including plastic soft closed seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc and including S&F of all necessary accessories set like rag bolts / gel gasket / hinges etc as recommended by manufacturer for fixing , packing and taking down of any description / size complete in all respect all as specified and as diretded by Engr-In-Charge.
S&F in repairs concealed flushing cistern of PVC 8 Litres cap with dual flushing system , valveless symphonic action type , with inlet , outlet , ball valve, float and including brackets and connection to pipes etc and including S&F of all necessary accessories / installation kit and S type drain pipe connection set for wall hung WC wtc as recommended by manufacturer for fixing , packing and including S&F of actuator knob / flush plates and taking down existing any description / size complete in all respect all as specified and as diretded by Engr-In-Charge.
S&F vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including S&F all accessories as recommended by manufacturer and incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified.
S&F central hole wash basin mixer 15mm bore brass without polp up waste with 10mm dia 450mm long copper pipes complete all as specified and directed by Engineer-in-Charge.
S&F health faucet to EWC ,CP brass with minimum 1000mm long CP flexible pipe, connection etc., complete all as approved by engineer -in -charge
S & F PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified and directed by Engineer-in-Charge.
S&F vitreous china urinals, Half stall type flat back complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe including waste pipe and trap complete all as specified and directed by Eng in charge.
S&F Urinal spreader of PTMT any colour for fixing 15 mm dia pipe complete all as specified and directed by Engineer-in-Charge.
S & F waste couplings of stainless (half or full threaded) of 32 mm complete all as specified and directed by Engineer in charge.
S&F low density polyethylene pipes (LDPE) 32 mm x 800 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer in charge.
S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and directed by Engineer-in-Charge.
S&F in repairs SS soap dish of any size fixed with screws complete all as specified and directed by Engineer in charge.
S & F in repair stainless steel tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.
S & F in repair stainless steel towel ring min 30mm dia including brackets complete all as specified and directed by Engineer - in - Charge.
S&F corner glass self 300mm ( withBrass Brackets) fixed with chromium plated screws etc complete all as specified and directed by Engineer - in - Charge.
S&F Stainless Steel grating 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified and directed by Engineer-in-Charge.
S&F Stainless Steel grating 100mm dia without hole (Minimium weight 25 grams) complete all as specified and directed by Engineer-in-Charge.
S&F hat pegs and hooks (cloth hanger with six peg set each) complete all as specified and directed by Engineer-in-Charge.
Dismantling structural steel work including doors, gates and staircase railing but excluding framed truss complete all as specified and directed by engr-in-charge.
M&L mild steel work as in framed work for iron ladder i.e. Angle iron/flat iron including caps , bases, splices, all lattice bars, cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed .
S&F in repairs stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.
Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.
M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.
All as per Srl item No -119 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.
All as per Srl item No -119 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.
All as per Srl item No. 119 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.
S & F modular switch 5/6 Amps single pole one way,one module complete all as specified and directed by Engineer - in - Charge.
S & F in repair Modular switch 1 way 16A, with box complete all as specified and directed by Engineer - in - Charge.
S & F in repair modular Socket, 16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.
S & F modular socket outlet 5 pin 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge.
S & F modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge
S&F Ceiling rose, surface baklite 65x17 mm three terminal ISI marked complete all as specified and directed.
S&F in replacement of existing light fitting with LED high bay, 72W with aluminium housing and integrated electronic driver, 72 watt having input voltage AC 90-300V, 50 Hz, 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/ connector complete all as specified and directed by Engineer - in - Charge
S & F in replacement of existing light fitting with LED batten with aluminium housing and integrated electronic driver, 20 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.
S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge
S & F in replacement Water tight bulk head fitting,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery ,glass well,and including 10 watt LED lamp all as specified and directed by Engineer - in - Charge
S & F in repair compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified.
S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge
S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.
S & F of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.
S & F of sub-main wiring with two single core cables PVC insulated and un-sheathed 4 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 4.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.
S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 125A ,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.
S&F in repairs MCCB 4 pole 63 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.
S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.
S & F in repairs MCB ‘C’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole & neutrtal with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.
S & F in repairs MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.
M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge
Taking down fan, ceiling cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer - in - Charge.
S&F heavy duty metal body exhaust fan of 250mm sweep , 240 volt , complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in CM (1:4) white washing matching with existing color etc complete all as specified and directed by Engineer - in - Charge.
S&F Rigid non-metalic PVC conduit 20mm dia inclusive of all tees, bends, elbows reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed by Engineer - in - Charge.
Supply & fix TV Scoket having holes for 20mm conduit entry for TV connections complete all as specified and directed by Engineer - in - Charge.
Taking down old unsv existing LT cable of any capacity complete all as specified and directed by Engr-in-charge.
Supply and lay jointing and testing and commissioning in replacement of 25 Sqmm x 4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by Engr-in-charge.
Excavation in trenches not exceeding 1.5 mtr wide and not ecxceedinf 1.5 mtr depth for laying of cables including taking up or down the LT cable complete all as specified and directed by Engr-in-charge.
Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engr-in-charge.
Removal of Excavated material not exceeding 50 mtr and depositing where directed complete all as specified and directed by Engr-in-charge.
Supply and laying DWC pipe of outer dia size 77 mm and inner dia 63mm for laying of Lt cable complete all as specified and directed by Engr-in-charge.
Supply and lay GI pipe 50 mm light grade for cable protection in walls trenches or any situation including clamp nut bolt etc complete all as specified and directed by Engineer-in-Charge.
Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine for laying of DWC pipe of outer dia 90 mm complete all as specified.
Please Enable Macros to View BoQ information
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.38 MB
BOQ_837984.xls
BOQ • 0.40 MB
Tender_104.pdf
Tender Documents • 1.21 MB
Download all tender documents and submit your bid