Construction of New medical College at Port Blair. Sub Work_ Proposed Construction of Boys Hostel Block _ III for Medical College at Dudh line Port Blair including IEI.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources).

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources).

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand derived from natural sources): 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed by stone metal 40 mm nominal size, well rammed and consolidated and grouted with coarse sand (Zone - III), including finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :

1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

A) Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from approved quarry).

B) Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources).

Centring and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases.

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards.

Extra for shuttering in circular work (20% of respective centring and shuttering items).

Weather shade, Chajjas, corbels etc., including edges.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063).

a) Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063.)

Floor Joint of 100 mm gap

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 16.1) Granite of any colour and shade 16.1.1) Area of slab upto 0.50 sqm

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of size 450x300 mm as approved by Engineer-in-Charge, in external wall cladding and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (of make Asian, NITCO, Kajaria, Somany, Johnson, Orient bell, OASIS or equivalent brand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Teak wood/Padauk category I-A

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 20.1) Float glass panes. 20.1.1) 4 mm thick glass pane (weight not less than 10kg/sqm).

Providing and fixing dash fasteners for fixing door & window frames of required size, including necessary stainless steel screws, all complete as per the directions of Engineer-in-charge. (Brand : Hilti, Fischer, Anchor, Kundan)

Providing and fixing bright finished stainless steel tower bolts (barrel type) with necessary screws etc. complete of approved brand as per direction of Engineer-in-charge.

Providing and fixing bright finished brass handles with screws etc. complete :(Make with IPSA brand or equivalent) as per direction of Engineer-in-charge.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- in-charge

Extruded section Profile size 48x40 mm.

Providing and fixing factory made PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. Area of window. i) upto 0.75 sqm

Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm). i) upto 1.50 sqm

Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm). i) upto 2.00 sqm

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately).

Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Providing and fixing stainless steel ( Grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (As per drawing)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Coupler 41.1.1) 110 mm

Bend 87.5° 41.2.1) 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix :

1:4 (1 cement : 4 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement : 3 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying and stacking at site.

90 mm to 45 mm size stone aggregate.

63 mm to 45 mm size stone aggregate.

53 to 22.4 mm size stone aggregate

stone screening 13.20 mm nominal size (Type A)

stone screening 11.20 mm nominal size (Type B)

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :

On W.B.M. @ 0.75 Kg / sqm.

2 cm premix carpet surfacing with 1.8 cum and 0.90 cum of stone chippings of 13.2 mm size and 11.2 mm size respectively per 100 sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete (tack coat to be paid for separately).

With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt using shreded waste plastic @ 8 to 10% of Bitument.

Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade, including required key aggregate as specified, spreading coarse aggregate with the help of self propelled/ tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy :

For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded @ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10 sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10 sqm.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Flat back urinal of size 355x345x535mm (URS-WHT-13261)with pressmatic urinal valve auto closing system with built in control lock & wall flange for urinal complete set alongwith instalation with control cock (of Jaquar Code No. PRS077 and equivalent) including fittings and cutting and making good the walls and floors wherever required (Jaquar, Hindware, Roca, Parryware, Kohler and equivalent).

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :(Parraway, Hiraware, Hindustan Roca, Kohler ,Prayag and equivalent Brand)

White Vitreous China Wash basin size 550x400 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 67.1) Semi rigid pipe. 67.1.1) 32 mm dia

Providing and fixing 100 mm stainless steel grating for gully trap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc. (make Supreme,Astral,Finolex,Prince or equivalent brand.

20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing brass bib cock of approved quality :(make JAGUAR, HINDWARE, ROCA,PARRYWARE,KOHLER and equivalent brand )

15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

25 mm nominal bore

32 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 77.1) 45 cm length 77.1.) 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :(make JAQUAR, HINDWARE, ROCA,PARRYWARE,KOHLER and equivalent brand)

150 mm diameter

Providing and placing on terrace (at all floor levels) circular polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 10 x 2000 litre

Making soak pit 2.5 m diameter 3.0 metre deep with 300mm stone boulder honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion.

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and laying seal coat of premixed River sand ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of River sand and 0.60 cum of River sand per 100 sqm of road surface, including rolling and finishing with road roller all complete.

Supplying and filling in plinth with River sand under floors including, watering, ramming consolidating and dressing complete.

Providing and Laying hollow cement concrete block walling upto floor five level 200mm thick consisting of hollow block of size 400 mm x200 mm x 200 mm of mix 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 10 mm nominal size). Having a crushing strength of 3.5N/sqmm at 28 days as Per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement : 6 pulverised sand) .complete..

Providing and Laying hollow cement concrete block walling upto floor five level 100mm thick consisting of hollow block of size 400 mm x200 mm x 100 mm of mix 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 10 mm nominal size). Having a crushing strength of 3.5N/sqmm at 28 days as Per IS:2185 (Part-I) 1979 laid in cement mortar 1:6 (1 cement : 6 pulverised sand) .complete..

Providing and laying waterproofing treatment at terrace with Dr. Fixit Flexi PU270(1) or equivalent.

Supplying and appliying single component, root resistant , elastomeric pur polyurethane membrane free from bitumen and tar, Dr. Fixit Flexi PU270(1) or equivalent with minimum elongation of 400% and solid content 90%. The system consists of applyin the waterproofing treatment @1.35KG/sqm to achieve a DFT of 1.2mm.

Providing & laying of proctective Geotextitile fabric 150GSM over the entire membrane with proper overlaps

Supplying and applying UV Resistant TOP Coat.

Providing and fixing CP towel ring as approved by the Engineer-in-charge with concealed fittings arrangement of approved quality and colour.(Jaguar , Hindware, Roca, Parryware,Kohler and equivalent)

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (part 1) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S piano hinges with necessary screws.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in external wall cladding and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(of make Asian,NITCO,Kajaria,Somany, Johnson,Orient bell, OASIS or equivalent brand)

Size of Tile 450x300 mm

Providing and laying antiskid Ceramic floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.(of make Asian,NITCO,RAK,Restile,Kajaria,Somany, Johnson,Orient bell, Varmora Granito or equivalent brand)

Providing and laying Vitrified antiskid floor tiles 600x600 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigments etc., complete.(of make Asian,NITCO,RAK,Restile,Kajaria,Somany, Johnson,Orient bell, Varmora Granito or equivalent brand)

Size of Tile 600x600 mm and 1200x300mm

Providing and laying Vitrified antiskid floor tiles tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.(of make Asian,NITCO,RAK,Restile,Kajaria,Somany, Johnson,Orient bell, Varmora Granito or equivalent brand)

Size of Tile 600x600 mm and 1200x300mm

Providing and fixing 0.71 mm thick (Weight not less than 2.18 kg per sqm) colour coated Aluminium Modern Troughed sheets accessories, made of AA 3003 alloy confirming to IS 737-1974 in full hard (H18) tamper of HINDALCO Ever last or equivalent as approved by Engineer-in-charge and polyster top coat 15-18 microns using self drilling / self trapping stainless steel screws complete.

Providing and fixing 0.71 mm thick (Weight not less than 2.18 kg per sqm) colour coated Aluminium Modern Troughed sheets accessories, made of AA 3003 alloy confirming to IS 737-1974 in full hard (H18) tamper of HINDALCO Ever last or equivalent as approved by Engineer-in charge and polyster top coat 15-18 microns using self drilling/self trapping screws complete.

ridge plain (900mm).

valley (900 mm over all girth).

Extra for providing and fixing wind ties of 40x 6mm alumunium section.

Providing and fixing calcium silicate board in ceiling with suitable screws etc. complete (frame work to be paid separately) :

6 mm thick

Providing and fixing CP soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106gms. (make Jaquar, parryware, kohler, metro, leader, waterman, seiko, prayag and equivalent brand)

Providing and fixing C.P two way Bibcock of approved quality(make JAQUAR, HINDWARE, ROCA,PARRYWARE,KOHLER and equivalent brand

15 mm nominal Bore

Providing and fixing health faucet of approved quality (make (make JAQUAR, HINDWARE, ROCA,PARRYWARE,KOHLER and equivalent brand

Providing and fixing C.P Brass Angular Stop cock of Cat CON-053 make jaquar.(make of KOHLER, JAQUAR or equivalent brand)

15mm nominal bore

Providing and fixing CP towel rail as approved by the Engineer-in- charge with concealed fittings arrangement of approved quality and colour (make of KOHLER, JAQUAR or equivalent brand)

450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.

Providing and fixing concealed stop cock with fitting sleeve,operating lever and adjustable wall flange.(make JAQUAR, PARRY WARE, KOHLER or equivalent brand

15 mm nominal bore.

Providing and fixing soil, waste and vent pipes : with UPVC pipe coforming to IS:13592 type B including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion(i) single socketed pipes (make SUPREME, PRINCE,FINOLEX or equivalent brand)

110 mm dia.

75 mm diameter :

Providing and fixingUPVC terminal guard (make SUPREME, PRINCE,FINOLEX or equivalent brand

Providing and fixing 110 mm dia PVC door bend of approved quality.

Providing cement concrete surface drain including earthwork excavation 10 cm thick base concrete and 15 cm thick side wall with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate of 40 mm nominal size) cement concrete finished with 1:4 (1 cement : 4 sand) a floating coat of neat cement inside the drain the drain and its top and exposed surface including earthwork in excavation and disposed of surplus earth etc.

23 X 23cm surface drain.

Constructing cement concrete 1:3:6 mix ( 1 cement ; 3 corase sand zone-III ; 6 graded stone aggregate 40 mm nominal size ) manhole R.C. C top slab with 1:2:4 mix ( 1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size ) , foundation concrete 1: 4:8 mix ( 1 cement : 4 coarse sand( zone-III) : 8 graded stone aggregate 40mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand (zone-III) finsihed with floating coat neat cement and making channels & cement concrete 1:2:4 ( 1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design.

a) Inside size 90x80 cm and 45 cm deep including C.I cover with frame (light duty) 455x610mm interial dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23kg and weight of frames 15kg )

Supplying and filling filter media with stone boulder of size 120mm

Providing weep hole with 75mm dia PVC pipe.

Providing and fixing PVC pre-moulded Septic Tank for 75 to 100 users including excavation in earthwork, refilling and disposal of surplus earth, installation and connecting with sewage lines, all complete.

Providing and laying Restiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS : 15622 of approved make ,in al colours and shade ,in skirting, riser of steps over 12mm thick bed of cement morter 1:3(1 Cement : 3Coarse sand) .jointing with grey cement slurry@ 3.3kg/sqm including grouting the joint withwhite cement and matching pigments etc. complete(of make Asian,NITCO,RAK,Restile,Kajaria,Somany, Johnson,Orient bell, Varmora Granito or equivalent brand)

size of tile 1200x300x14mm

Providing and fixing UPVC moulded double equal plain junction of required degree with access door insersion rubber washer 3mm thick, bolts and nuts complete for UPVC soil pipes conforming to IS:13592 type "B" including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion

Extra for using mainland river sand instead of coarse sand (zone-III) (Pulverized sand) in RCC works.

INTERNAL ELECTRIC INSTALLATION Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

1 x 1.5 sq. mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

3 pin 5/6 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

12 Module (200 mmX150 mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C"curve including connections, painting etc. as required

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required

Fixing of lighting conductor finial (single prong) with base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc. as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For vertical run)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required.

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3½ X 120 sq. mm (45 mm)

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Above 4.5 metre and upto 6.5 metre

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ Foundation (during casting) for cable entry including bending the pipe to the required shape complete as required.

32 mm dia

Excavation of the cable trenches in hard rock not exceeding 1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter.

Providing and laying in position cement concrete 1:3:6 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc. as required.

80 mm dia

Supplying of LED batten industrial box type luminaire (CRCA) suitable for single LED tube Make:- Crompton Cat.No.IGP131LT8-16 and 20 watt LED T8 tubelight with PC body Make :- Crompton Cat.No.LT8-20-865-2 respectively or equivalent complete with all accessories etc. as required.

Supplying of AC ceiling fan 1200mm sweep Make :- Havells ES -50 Premium 5 star rating (White/Brown/Ivory) or similar in Make:- Usha/orient/Crompton Greaves of ISI standard complete with all accessories etc. as required.

Supplying of Exhaust fan 230mm sweep (metallic Range ) Make:- Havells Ventil Air-DSP or similar in Make:- Usha/orient/Crompton Greaves of ISI standard complete with all accessories etc as required.

Supplying of 16 W LED Square Surface mounted luminaries Make :- PHILIPS Cat.No.SM200C LED 16S 6500PSU OD WH or similar in Make:- Bajaj/Crompton Greaves /Havells complete with all accessories etc as required.

Supplying of 34 W LED Square surface mounting which provides soft-light and glare free symmetrical illumination Make:- Havells , PLUTO PANEL (SURFACE) Cat.No. PLUTOSURFACE2X2PLS34WLED840S or similar in Make:- Bajaj/Crompton Greaves complete with all accessories etc as required.

Supplying of 6 W slim surface mounted square LED panel die cast body with premium diffuser to ensure glare free & even distribution of light Make:- Havells COMET SQUARE Cat.No. LHEAAWP7IL1W006 or similar in Make:- Bajaj/Crompton Greaves complete with all accessories etc as required.

Supplying of 6 W LED Ultra slim decorative all plastic body lit panel recess mounted square fixture in white finish suitable for low ceiling height Make:- Havells FAZER SQUARE Cat.No. LHEBMDP7UZ1W006 or similar in Make:- Bajaj/Crompton Greaves complete with all accessories etc as required.

Supplying of 15 W LED Recess Square downlights Make :- Havells EDGEPRO SQUARE Cat.No. EDGEPROSQDLR15WLED840S or similar in Make:- Bajaj/Crompton Greaves complete with all accessories etc as required.

Supplying of 10 W LED Endura RUGBY NEO N-IP65 Bulk head fitting Make:- Havells Cat No. RUGBYNEONFT10WLED860SSYMTOPC or similar in Make:- Bajaj/Crompton Greaves complete with all accessories etc as required.

Supplying of 7W LED mirror light fitting Make:- Crompton LINNET Cat.No.LCL-07-CDL or similar in Make:- Bajaj/Havells/Philips complete with all accessories etc as required.

Supplying of 12W LED GLOBE decorative wall light fixture made up of Polycarbonate suitable for 12w Make:- Havells Cat.No.LHFOFUE1TZ1 W012 and LED adore 3W B22 WW Ball lamp Make:- Havells Cat.No.LHLDERUEMD8X003 respectively complete with all accessories etc as required.

Power safe enclosures Conforms to IS:8623, IEC:60439 "G" frame Panel boards, O/G Four pole MCCBs G-Frame 400A "CN" frame MCCB 6 way outgoing double door Make:- Havells Cat No.IHVGF4000600 or equivalent - 01 No.

Cable alley for 'G' frame panel boards -outgoing four pole MCCB inncomer 'A' & "C" frame MCCB i/c 400A/630A/800A, O/G 3P GF 8 way, 4P 6 way & A/F 6 way double door Make:- Havells Cat.No. ISSBOU0699 or equivalent - 01 No.

Adjustable thermal & adjustable magnetic setting four pole MCCB 400 Amps breaking capacity 35(KA) Make:- Havells Cat. No. IHLCNF0400# or similar in Make:- GEC/Indo Asian/Legrand - 01 No.

Fixed thermal & fixed magnetic setting four pole MCCB 63 Amps breaking capacity 25(KA) Make:- Havells Cat. No.IHLGHF0063 or similar in Make:- GEC/Indo Asian/Legrand - 04 Nos.

Fixed thermal & fixed magnetic setting four pole MCCB 100 Amps breaking capacity 25(KA) Make:- Havells Cat. No.IHLGHF0100 # or similar in Make:- GEC/Indo Asian/Legrand - 04 Nos.

Supplying of PVC insulated and PVC sheathed aluminium conductor armoured XLPE power cable of 1.1KV grade of following sizes etc as required.

3.5 core x 120 sqmm

2 core x 10 sqmm

Supplying of ENDURA CITYLINER NEX GEN street light fitting New generation energy saving & environmental friendly long life LED street light made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover with IP66 Make:- Havells Cat No.ENDURACITYLINERNEXGENSL 48WLED757SASYBOPC or equivalent complete with all accessories etc as required.

Fabrication of metallic street light pole of standard length exceeding 4.5 metre but not exceeding 6.5 meters made out of 65mm dia G.I pipe and 32mm dia G.I pipe for fixing street light fitting including fixing sintex box of inside dimension of size 140mm x 140mm x 95mm Code No. GSJB 1414 containing 1 No. MCB 6A etc as required.

Installation, testing & commissioning of LED street light fitting fitting including connection etc as required.

Supplying, installation, testing and commissioning of ASHLOK make SEE brand safe earthing electrode type-19, 50mm dia, length 2 mtrs (short time current -52.6 rms for 1 sec, peak-125.6) with back fill compound including providing masonary enclosure with cover plate having locking arrangement etc. as required.

Supplying , installation, testing and commissioning of Inverter 2800W, 48V, DU-3500 SINE WAVE INVERTER Make:- V -Guard or equivalent complete with all accessories etc as required.

Supplying , installation, testing and commissioning of Lead acid battery (Tall tubular) 12V , Capacity-full load,2.5 hours ,VT-150AH Make:- V-Guard or equivalent complete with all accessories etc as required.

Supplying, installation, testing and commissioning of Push button dialer Beetel B-15or equivalent complete with all accessories etc as required

Supplying, installation, testing and commissioning of ISI marked CO2 type Fire Extinguisher 2 Kg complete in all respect Make:- Everex/Fire Stone Minimax/ Safety First or equivalent to ISI standard

Supplying, installation, testing and commissioning of ISI marked CO2 type Fire Extinguisher 4.5 Kg complete in all respect Make:- Everex/Fire Stone Minimax/ Safety First or equivalent to ISI standard

Supplying, installation, testing and commissioning of 1.5 Ton 5 star ( As per 2018 BEE star rating) Inverter High wall split type Air conditioner(Twin/dual rotary compressor 1 phase 220 volt) Make:- HITACHI KASHIKOI 5100X Model RSOS518HCEA or equivalent with maximum cooling capacity of atleast 5250 watts( with copper condenser coil) including providing standard length of refrigerant copper pipe kit, cutting, drilling holes on the wall, cementing, painting to give an even look and smooth finish, wrapping PVC non adhessive white tape over insulation of gas pipe etc as required and as per the direction of Engineer-in-charge.

Supplying and fixing of 4 KVAvoltage stabilizer suitable for 1 /1.5 ton Air conditioner as required of Make :- V Guard Model VND 400 ( Voltage Range 150 V- 285 V ,12 amps ) or equivalent.

Providing and fixing of pre-fabricated stand for keeping outdoor units of 1 Ton/1.5Ton/2 Ton capacity split type AC as required.

O P KANDOI AND COMPANY PVT LTD

M/S Sophia Constructions

MM KAILASH CONSTRUCTION PVT LTD

Salcon Engineers andFabricators

MANICKAM ENTERPRISES