Upgradation of 24 nos. of existing Hospitals for setting up of ICUs for treatment of patients of COVID-19 under Assam Critical Care Project-2020 at Darang

Amount

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Demolishing RCC work including stacking of steel bars and disposal of unserviceable material as directed for all levels

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Demolishing CC floors of various thickness including top layer and base course and disposal of debris as directed for all levels.

Demolishing the plastering from walls/ R.C.C. and P.C.C. members without causing any damage to the wall/ member upto any height including disposal of debris as directed for all levels.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Carriage of Material By Mechanical Transport including loading ,unloading and stacking up to 5 km (Earth)

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. In ordinary soil Up to a depth of 2.00 M below the existing ground level.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Stone soling of thickness 150mm.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Plain cement concrete works with coarse aggregate of sizes 13 mm to 32 mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, curing complete (Shuttering where necessary shall be measured and paid saperately). In prop 1 cement :4 Sand :8 coarse aggreget by volume

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundations, footings, bases of columns, pile cap, raft and mass concrete work etc. (b) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides of tie beams, grade beams etc. at or below ground level. For depth not exceeding 1.0 M (b) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts and Struts Suqare, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face. (ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above 1st Floor

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. Suqare, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face. (a) For depth not exceeding 1.0M. (ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Flat Surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconiess and the like. (a) Floors etc. upto 200mm in thickness. (ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Staircase with sloping or stepped or stepped soffits including riser and stringers but excluding landing. Using 38 mm thick plank.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Providing form work of ordinary timber planking and removal of the same in edge of slab and breaks in floors and walls etc. of in situ reinforced concrete work upto first floor level. Thickness not exceeding 200 mm

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Extra for each subsequent floor or part thereof above the first floor level as mentioned in item no. 3.1.3(a). 1st Floor

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Cornices and mouldings

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosion resistant steel (CRS) reiforcement bar.

Extra over above item 18.1.1(a,b,c) for each subsequent floor or part thereof above first floor level.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. B) Using admixture, plasticiser etc for air entraining, water reducing purposes including addition of agent for changing normal setting time of concrete as required. C) M25 grade concrete

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. (I) Using Mixer Machine (B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. P) Using admixture, plasticiser etc for air entraining, water reducing purposes including addition of agent for changing normal setting time of concrete as required. c) M25 grade concrete

Extra over item above for each subsquent floor or part thereof above 1st floor level. 1st Floor

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.4.1) C) UNIFORM PILE (III) Concrete Grade M25 i) Pile dia 400 mm

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (d) In proportion 1:6

Superlight weight Autoclaved Aerated concrete Block work using Grade-I AAC Block of size 625x240mm of different thickness of compresive strength 40 kg/cm2 having dry density 550 to 650 kg/cum conforming to IS : 2185 pt-3 or pt-4 in cement mortar of Prop 1:4 including racking out joints and curing complete as specified & Directed.(Protruding rod is to be provided at every 3 course interval and will be measured and paid seperately) (II) In Super-Structure above plinth level up to 1st Floor level. For 225 mm Thick Wall (Gr. Floor To Terace Floor)

Extra for AAC block walling for each subsquent floor or part thereof above 1st floor level. (i) 225 mm thick wall. 1st Floor

Extra for AAC block walling for each subsquent floor or part thereof above 1st floor level. (i) 225 mm thick wall. 2nd Floor

Superlight weight Autoclaved Aerated concrete Block work using Grade-I AAC Block of size 625x240mm of different thickness of compresive strength 40 kg/cm2 having dry density 550 to 650 kg/cum conforming to IS : 2185 pt-3 or pt-4 in cement mortar of Prop 1:4 including racking out joints and curing complete as specified & Directed.(Protruding rod is to be provided at every 3 course interval and will be measured and paid seperately) (II) In Super-Structure above plinth level up to 1st Floor level. For 125 mm Thick Wall (Gr. Floor To Terace Floor)

Extra for AAC block walling for each subsquent floor or part thereof above 1st floor level. (i) 125 mm thick wall 1st Floor

Extra for AAC block walling for each subsquent floor or part thereof above 1st floor level. (i) 125 mm thick wall 2nd Floor

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (Area of slab upto 0.50 sqm)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (Area of Slab over 0.50sqm)

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work.

Extra for fixing marble/granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform. Vanity counters and similar location in marble/granite/stone work including necessary holes for pillar taps etc. including rubbing,moulding and polishing of cut edges etc. complete.

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. Decorative type and block board core. 40 mm thick.

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. b) Non decorative type and block board core. (ii) 35 mm thick .

Extra for providing lapping with 1st class Teak wood battens of 25mm minimum depth on all edges of the shutters.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square.

Providing and fixing fire resistant door frame of section 50 x 60mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in-charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 15 min of insulation (EI15) and having a sound reduction of 37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be manufactured in UL & TUV audited Facility and including UL-EU Certification.The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report for the complete system (Glazed Door or Partition) will be considered valid only if it contains the stamp and signature of the authorized signatory from the glass manufacturer. (Actual glass size is to be measured at site for payments).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade SS 304 grade Mortice lock with key cylinder fixed fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ). b) Tower Bolt ii) 250mm x 10mm

Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ) b) Tower Bolt iv) 150mm x 10mm

Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Toilet Cubical Providing and fixing Toilet Cubicle (of following standard dimension which includes 600 mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 12 mm thick solid compact laminate panels Finish of the compact laminate should be raw silk which include doors, pilasters and intermediate panels finished with approved texture/shade as per the detail drawing and as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless Steel (Grade 316) as per manufacturer's specifications and EIC instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U- Channels, (6) SS-Shoe Box Plate, (7) MS-Base Plate, (8) Rubber noise deafening tape, (9) Screws and wall Plugs.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop 1:3:6 (1cement : 3coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement : 1coarse sand : 2 coarse aggregate of 10 mm and down) finished with a floating coast of neat cement finish using cement slurry for bond @ 2.75 kg. per sqm. of floor area, wearing layer is to be laid in panels including curing complete as directed.

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (b) 20 mm thick

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Delux range Somany/ Orient/Nitco/Qutone Make Of size 300mmx300mm and above

Providing polished Ceramic wall Tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 Cement: 3 Coarse sand), including cutting where necessary finished with flush pointing with fix-A Tile (Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry) mixed with approved pigment to match the shade of tiles complete at all levels as specified and directed (coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Wall means both interior and exterior walls). Delux Range (Somany/ Orient/ Nitco/ Varmora Make) of size 300mm x 450mm and above

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) Of size 600mmx600mm and above

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) c) Delux range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make Of size 1000mmx1000mm and above

Providing Polished vitrified wall tiles of approved quality of specified size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)/ White cement slurry mixed with approved pigment to match the shade of tiles complete at all levels as specified and directed (coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). Of size 300mm x 600mm and above

Providing Polished Granite Slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (Cement plastering to be measured and paid separatly) (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). (iii) Delux Quality (i)With Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement

10 mm cement plaster in single coat on fair side of brick/concrete walls for interior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 (Gr. Floor to Terrace Floor)

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. 1st Floor

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. 2nd Floor

15 mm cement plaster in single coat on rough side of single or half brick walls for interior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 (Gr. Floor to Terrace Floor)

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. 1st Floor

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. 2nd Floor

Providing & fixing Chicken wire mesh on joints of RCC & Brick work before plastering complete in the direction of Engineer-in-charge.

White washing with lime on wall surfaces (two coats) to give an even shade including throughly brooming the surface to remove all dirt, dust,mortar drops and other foreign matter. New work (Two coats)

Extra over item no. (a) above for every subsequent coat of white washing with lime on wall surfaces.

Providing two coats of Birla White Wall Care Putty (Water Resistance White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm). Thickness = 1.5 mm thick

Finishing old/ new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of required shade after clering and clearing the surfaces etc.including scaffolding complete as directed at all levels (two coats).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-incharge complete. Upto 5mm depth and 5 mm width

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing 12 mm thick frameless toughened glass partitions of approved brand and manufacturer, including providing and fixing partitions at top & bottom with aluminum channel etc. all complete as per direction of Engineer-in-charge

Providing and fixing approved brand and manufacture SS 304 grade Top & Bottom Patch fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade D type 300mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Glass to Glass Lock Round type with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65mm.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75 x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000mm length and L-hape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications

Providing and fixing 300mm wide 1mm thk grade-304, SS Kick plate over flush door with suitable adhesives, screws etc. all complete as per direction of Engineer-In-Charge.

Providing & Fixing PVC Stretcher Guard minimum 150 mm wide with extruded aluminium base including all accessories per approved design all complete as per direction of Engineer-In-Charge.

Providing & Fixing PVC. Corner guard 40x40x4mm size fixed to wall including fixing arrangement as per approved design all complete as per direction of Engineer-In-Charge.

Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately). Indian type W.C Orissa pattern of size 580 x 440 mm C) Jaquar Make I) White

Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately). C) Jaquar Make I) White (i) Size 530 x 370x 360 (Cat No.CNS-WHT-WS01) (inclusive of seat cover)

Provinding fitting and fixing Vitreous china wall hang water closet (European type W.C PAN 400 mm high) with seat and lead, CP Brass hinges and rubber buffers , CI/MS brackets,40 mm dia flush band with fittings including painting of fittings and brackets, required.(flushing Cistern to be paid separately) C) Jaquar Make I) White (ii) Solo Cat. No. SLS-WHT-0117 (inclusive of seat cover and fittings)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately). A) Parryware make I) White (i) Economy Single Flush (Cat No.C8090/C8055)

Supplying ,fitting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) C) Jaquar make Concealed Cistern ( Cat. No. CIB-WHT-31801011X) with Control Plate (CP) (Cat.No. CIS-CHR-31191510X)

Provinding vitreous china wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required.(Pillar cock, stop cocks, waste coupling are to be paid separately )Table Top Basin ( c) Jaquar Make (ii) Solo ( Cat. No. SLS- WHT-0558)

Providing fitting & fixing laboratory sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately. (A) Parryware Make a) White (i) Lab Sink 450mm (Cat.No.C0602)

Provinding vitreous china wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required.(Pillar cock, stop cocks, waste coupling are to be paid separately )Table Top Basin ( c) Jaquar Make (iii) Lyric ( Cat. No. LYL-WHT-0555)

Providing fitting & fixing stainless steel kitchen sink of parry make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings, cutting & making good the walls wherever required.( Sink cock, stop cocks, waste coupling are to be paid separately . (A) Parryware Make (ii) Single Bowl with Drain board (400x200) flat Edge - Glossy ( Cat. No. C8537)

Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make (a) Size 800mmx 600mm

Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make (b) Size 600mmx 450mm

Providing,fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar make ( e) Hotelier (Cat.No. AHS - 1531)

Providing fitting and fixing liquid soap dispenser and liquid soap container complete as directed ad specified. (i) Jaquar make ( c) Kubix with glass bottle (Cat.No. AKB-35735)

Providing fitting and fixing CP towel rail complete as direted and specified (a) Jaquar make (vii) Kubix(600mm long) (Cat.No. AKB-35711)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make (ii) Continental towel ring round (Cat.No. ACN-1121BN)

Providing ,fitting and fixing chrome plated robe hook complete as direted and specified. (a) Jaquar make (iii) Kubix (Cat.No.AKB-35791)

Providing, fitting and fixing chrome plated tumbler holder complete as directed and specified. (a) Jaquar make (iii) Kubix (Cat.No.AKB-35741)

Providing fitting and fixing chrome plated TOILET PAPER holder of complete as directed and specified (a) Jaquar make (ii) Continetal toilet paper holder with flap(cat.No. ACN1153N)

Providing ,fitting andd Fixing chrome plated waste coupling complete as directed and specified. (a) Jaquar make (i) 32mm (HT/FT) (Cat.No. ALD-705/709

Providing ,fitting andd Fixing chrome plated Bottle Trap complete as directed and specified. (a) Jaquar make (i) Bottle trap (with internal partition) 32mm size with 250mm long wall connection pipe(Cat.No.ALD-769)

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately). Jaquar make (a) Continental / clarion (ii) Bibcock long thread

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately). Jaquar make (a) Continental / clarion (iii) 2-Way bib cock

Supplying fitting and fixing chorom plated (C.P) stop- cock of approved brand and size as mentioned below as directed and specified.(G.I) & C.P Pipes will be measured and paid separately) Jaquar (a) Continental / Clarion (iii) 15mm (Angular stop cock with long thread )

Supplying and fiiting fixing C.P pillar cock of 15 mm dia of approved brand as specified and directed. Jaquar make (a) Continental

Supplying,fitting and fixing chorme plated (C.P) shower 15 mm dia. Of approved nrand as directed and specified.( pipes will be measured and paid separately) Jaquar Make (a) Continental (iii) Pressure adjustable shower with revolving joint

Supplying, fitting and fixing Chorme plated (C.P) basin mixer complete as directed . (II) Jaquar make (For VIP use. Prior approval of chief Enginner PWD (Bidg) must be taken before use) (a) Continental/ Clarion (iii) Central hole basin mixer without popup waste system with 450mm long coper pipe and brass nuts Cat.No. 169

Supplying, fitting and fixing Chrome Plated (C.P) sink mixer complete as directed. Jaquar make (a) Continental / Clarion (i) Sink mixer with swinging casted spout ( wall mounted model) Cat No. 309

Supplying , fitting and fixing Chorme Plated (C.P) divertor of approved brand complete as directed . Jaquar make (a) Continental/ Clarion - 4 way divertor for concealed fitting with build in non return valves with divertor handle Cat. No.421

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook. ( MAKE-1: JAQUAR, MODEL NO. HEALTH FAUCET : ALD-CHR-573GA OR EQUIVALENT.)

Providing & fixing wall mounted 300mm Long SS Grab Bar including cutting & making good the walls. ( MAKE-1: JAQUAR, MODEL NO. GRAB BAR : AKP-CHR-35701PS OR EQUIVALENT.)

CP Braided hoses connection 450 mm long including nuts and washers and making connection to fixtures and fittings complete as required. ( Base Rate:250)

Providing and fixing of fully automatic "NO TOUCH" durable & shock proof hand drier of approved make & manufacture suitable to operate on 220 volts, single phase 50 hz, A.C. power supply, 1500 Watt and directly plugged to power point complete in ABS plastic body having drying time 20-30 seconds complete as per direction of Engineer in Charge. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge. ( MAKE JAQUAR MODEL NO.- HDR-SAP-M99ACS or EQUIVALENT.)

Providing and fixing of Storage type water heater/ Geyser with required accessories like 15 mm CP angle valve on inlet & outlet line, heavy duty reinforced flexible PVC connector for cold water line and flexible CP brass connector with CP checkout for hot water line, CPVC line connection, MS bracket with two coats of enamel paint, anchor fastners etc to hang the units, providing and fixing of 16 A 3 Pin plug of Anchor make, etc complete as required. Capacity 15 Liters

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 160mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 110mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 75mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 63mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. In Exposed Surface or in Trenches. 50mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 75mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 63mm dia

Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 50mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 160mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 75mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 50mm dia

Supplying fitting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . a) In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . a) In Exposed Surface or in Trenches. 75mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . a) In Exposed Surface or in Trenches. 50mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 50mm dia

Supplying fitting and fixing PVC plain single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . a) In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing PVC plain single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110mm dia

Supplying fitting and fixing PVC plain single Y of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing PVC plain single Y with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . a) In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing PVC coupler of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing PVC coupler of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 75mm dia

Supplying fitting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches. 110mmx75mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified. 110mm

Providing fitting and fixing PVC of cowel of ISI make complete as directed and specified . 110mm dia . PVC cowel of ISI make

Providing fitting and fixing C.P. Grating of ISI make complete as directed and specified . 110mm dia

Providing and fixing uPVC P-Trap including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 hand stone ballast 20 MM nominal size) the inlet from floor level to trap rim to be grouted and cemented neat manner including cutting and making good the floor & wall wherever requiredcomplete in all respects. 110 mm inlet and 110 mm outlet.

Providing and fixing cast brass clean out plug with suitable insert keys for opening, male threaded joint with PP/ uPVC female threaded socket caulked to PP/ uPVC pipe including cost of Solvent cement or Other Joint. 100 mm dia

Providing and fixing in position 110x63 mm OD uPVC reducing elbow including fix to floor with cement mortar.

Providing and fixing 110 mm OD uPVC inlet fitting/ Extension Piece with 2 or 3 inlets of 40 to 63 mm OD, fixed to uPVC trap with solvent cement joint and set in cement concrete as per drawing complete.

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories) In internal Wall - Exposed on Wall (20 mm OD)

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories) In internal Wall - Exposed on Wall (25 mm OD)

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories) In internal Wall - Exposed on Wall (32 mm OD)

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories) In internal Wall - Exposed on Wall (40 mm OD)

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories) In internal Wall - Exposed on Wall (50 mm OD)

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. 50mm dia (Medium) Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. Exposed on Walls 40 mm dia (Medium) Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. Exposed on Walls 32 mm dia (Medium) Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. Exposed on Walls 25 mm dia (Medium) Using Tata make

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls 20 mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls 25mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls 32mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls 40mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls 50mm OD

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe) 25mm(OD) diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe) 32mm(OD) diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe) 40mm(OD) diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe) 50mm(OD) diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe) 75mm(OD) diameter

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 20 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 25 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 32 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 40 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : 50 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 25 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 32 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65mm nominal bore

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes) For 20 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes) For 25 mm dia Pipe

Providing and fixing forged brass single acting air release valve with screwed inlet 25 mm dia.

Providing, laying and Jointing G.I. "B class" pipes and fittings conforming to IS: 1239 (Medium class) with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) complete in all respects for internal works including pipe supports with galvanised GI. slotted angle iron, GI clamps, spacers as required and making good wherever required. (For Vertical in Shafts & Terrace only) Internal Work - Exposed on Wall 80 mm dia. nominal bore

Providing, laying and Jointing G.I. "B class" pipes and fittings conforming to IS: 1239 (Medium class) with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) complete in all respects for internal works including pipe supports with galvanised GI. slotted angle iron, GI clamps, spacers as required and making good wherever required. (For Vertical in Shafts & Terrace only) Internal Work - Exposed on Wall 65 mm dia. nominal bore

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia.

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth upto 1.5 metre). Pipes, cables etc, exceeding 80mm dia but not exceeding 300mm dia

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. 150 mm diameter S.W. pipe

Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With Sewer bricks conforming IS : 4885

Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With Sewer bricks conforming IS : 4885

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) up to haunches of S.W/RCC pipes including bed concrete as per standard design. 250 mm diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing bricks masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Tube Wells ( 2 Nos.) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size )

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level. All types of soil - 400 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil - 400 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. 200 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing 80 mm dia. GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.

Supply, Lowering, installation & testing of KSB make submersible pumping set with 7.5 HP motor 4 stage pump suitable for 20/26/30/38/40/45/50 m3 hr. at 42/38/36/32/29/25/20 mtr. Head respectively. With Three Phase. (Model: 273/4)

Providing & fixing cable 6 sq.mm. From submersible pump to panel board.

Providing & fixing Panel Board for submersible pump fitted with DOL starter ammeter, voltmeter single phase preventer standard/indo/cop make MCB of off switch push bottom duly wired and made out of 16/18 SWG sheet.

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. 80 mm dia.

Providing, installing, testing and commissining of variable speed (VSPS) hydropneumatic system mounted on a common base plate comprising of vertical centrifugal pumping set with S.S body, stainless steel impeller and mechanical seal, shaft directly coupled to a TEFC induction motor suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, dedicated variable frequency drive for each pump, one No.remote sensors, pressure transducers, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, one No. 60 litre capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including stainless steel grade 316 pipe suction and delivery headers and isolation/ control valves( ball valves/butterfly valves/ Nan return valves/ vibration eliminators etc as required) , power box, equipped with fuses/ isolators/circuit breakers as required. The entire Hydropneumatic system shall be factory fitted. Hyd. System for Domestic Water Supply at Terrace Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 1.0 LPS Head 20 M. HP 1.5 HP Approxi.

Supply Installation,Testing & Commissioning of metering pump type chemical doser with 100 lits. HDPE chemical grade solution tank,injection fitting assembly,suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects. Chlorination of Domestic Water

Level Controller For Sump Pumps: To start pump when water level is high in sump and shut off pump when sump is empty. Both pumps are start when sump is over flowing.

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. - 50 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. - 65 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. - 100 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. - 150 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . - 50 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . - 65 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . - 80 mm dia.

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . - 100 mm dia.

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . - 150 mm dia

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. - 50 mm dia

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. - 65mm dia.

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 16 Kg/Sqcm. - 50 mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 16 Kg/Sqcm. - 65 mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 16 Kg/Sqcm. - 80 mm dia

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. - Power cable Copper 3 core 10 sq.mm

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. - Power cable Copper 3 core 6 sq.mm

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. - Power cable Copper 3 core 4 sq.mm

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. - Control cable copper 2 core 1.5 sq.mm

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter

Design, Supply, Installation, testing and commissioning of Sewage Treatment Plant (STP) of 25 KLD capacity of approved make for the treatment of domestic sewage using Moving Bed Bio Reactor(MBBR) Technology, including, getting the design approved from engineer in charge, relevant standards, technical specifications and direction of Engineer-In-Charge. The characteristics of treated water shall meet pollution control board guideline, BOD-<20 mg/l, COD- <100 mg/l, TSS-<10 mg/l. The system shall be complete with all equipments including , Bar Screen (Coarse & Fine), Air Blowers (1W+1S), Sewage Transfer Pump (1w+1S), MBBR media, Tube Settler media, Filter Feed Pump (1W+1S), Filter Press (12"X12") with poly dosing system, Filter Press Feed Pump (1Nos.), Sludge Recirculation Pump (1W+1S), air diffusers, Anoxic Tank Agitator (1Nos.), UV, uPVC internal piping etc, MS tanks (Anoxic Tank, MBBR tank 1&2, Settling Tank, Filter Feed Tank, Sludge Holding Tank), Activated Carbon Filters (FRP), Dual Media Filters (FRP), electrical panels, cabling etc, Electromagnetic flow meter (1Nos.), Pressure Gauges, Level Controllers, complete in all respect. Blowers and pumps will be in combination of one working and one standby. The item includes all works including construction of bar screen chamber(RCC), OGT (RCC),equalisation tank (RCC), treated water tank (RCC/HDPE) and required concrete foundations for the equipment and sheded plant room. all complete including civil work and as per direction of Engineer-in-charge.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 25 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 32 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 40 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 50 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 65 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 80 mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright Sprinkler

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000 mm

Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge.. Capacity 4.5 Kg.

Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge. 6kg.Capacity

Wiring for Light/Fan/Call Bell Point with 3X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete including 6 Amp flush type switch / bell push (Anchor Penta / Gold medal / Kolar kany Kom/ Havells or equivalent make as approved by department. GI/MS switch board (ISI Marked) with phenolic laminated sheet cover, ceiling rose etc complete. Short point upto 3.00 metre length.

Wiring for Light/Fan/Call Bell Point with 3X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete including 6 Amp flush type switch / bell push (Anchor Penta / Gold medal / Kolar kany Kom/ Havells or equivalent make as approved by department. GI/MS switch board (ISI Marked) with phenolic laminated sheet cover, ceiling rose etc complete. Medium point upto 6.00 metre length.

Wiring for Light/Fan/Call Bell Point with 3X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete including 6 Amp flush type switch / bell push (Anchor Penta / Gold medal / Kolar kany Kom/ Havells or equivalent make as approved by department. GI/MS switch board (ISI Marked) with phenolic laminated sheet cover, ceiling rose etc complete. Long point upto 10.00 metre length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (finolex/RR Kabel/Nicco/Anchor or Equivalent make as approved by the Dept.) in surface/recessed ISI marked steel conduit pipe wiring system. with 2x1.5 sq.mm cable in 20 mm dia. Rigid Steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X2.5 sq.mm. + earth continuity with 1X1.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X4 sq.mm. + earth continuity with 1X2.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X6 sq.mm. + earth continuity with 1X4 sq.mm cable in 25 mm. dia. Rigid steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X16 sq.mm. + earth continuity with 1X10 sq.mm cable in 32 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X2.5 sq.mm. + earth continuity with 2X1.5 sq.mm cable in 25 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X4 sq.mm. + earth continuity with 2X2.5 sq.mm cable in 25 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X10 sq.mm. + earth continuity with 2X6 sq.mm cable in 25 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X16 sq.mm. + earth continuity with 2X10 sq.mm cable in 32 mm. dia. Rigid steel conduit.

Wiring for Light/Fan/Call Bell Point with 2X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete. Short point upto 3.00 metre length.

Wiring for Light/Fan/Call Bell Point with 2X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete. Medium point upto 6.00 metre length.

Wiring for Light/Fan/Call Bell Point with 2X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete. Long point upto 10.00 metre length.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Short point upto 3.00 metre length.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Medium point upto 6.00 metre length.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Long point upto 10.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Short point upto 3.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Medium point upto 6.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Long point upto 10.00 metre length.

Wiring for twin control light point with 1.5 sw. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe including 6 Amp flush type 2 way switch ( Anchor penta/Gold medal /Kolor Kany.Kom/Havells or equivalent make as approved by the dept.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rode etc complete. Long point upto 10.00 metre length.

Supplying and fixing 19 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in surface/recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 25 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 32 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 1-2 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 3 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 6 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 8 Module Type Metal

Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 6 amp one way modular clip in bell push MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting fixing of 6/10 amp one way modular clip in switch with LED , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of 6 amp 5 pin 2 module antibacterial universal socket outlet (Legrand/Scheinder/L&T) including making necessary connection as directed by the department Make Legrand (Myrium Cat no.673094) or its equivalent

Supplying with fitting and fixing of 16 amp one way one module antibacterial universal switcht outlet (Legrand/Scheinder/L&T) including making necessary connection as directed by the department Make Legrand (Myrium Cat no.673089) or its equivalent

Supplying with fitting and fixing of 6 amp one way one module antibacterial universal switcht outlet (Legrand/Scheinder/L&T) including making necessary connection as directed by the department Make Legrand (Myrium Cat no.73084) or its equivalent

Supplying with fitting and fixing of 6/16 3 module antibacterial universal socket outlet (Legrand/Scheinder/L&T) including making necessary connection as directed by the department Make Legrand (Myrium Cat no.673095) or its equivalent

Supplying with fitting and fixing of antibacterial 8 module front plate with frame (Legrand/Scheinder/L&T)as directed by the department Make Legrand (Myrium Cat no.673252) or its equivalent

Supplying with fitting and fixing of 6/10 amp two way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying fitting and fixing industrial plug & socket in surface mounted SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Dept. 20A Capacity. (ABB, Schneider MG, legrand, Hager make)

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting SPN MCB DB incorporated with bus-bar, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make). 12 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 8 way TPN (8+6+24) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 12 way TPN (8+6+36) double door

Supplying with fitting and fixing single pole 10KA 240/415V 50Hz MCB of the following capacity complete with making necessay connection as approved, specified and directed by the Dept. ( Schneider MG, legrand, Hager, Crabtree xpro make). C Series 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (Schneider MG, legrand, Hager, Crabtree Xpro make). C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (Schneider MG, legrand, Hager, Crabtree Xpro make). C Series - 63A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make). 30mA sensitivity DP RCCB - 40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make). 30mA sensitivity DP RCCB - 63A

Supplying with fitting and fixing Surge protector of max operation voltage 350V at 400 V network for maximum discharge current 40KA with operator indicator and draw out cartridge of (Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the dept. Surge protection Max operating voltage 340V Standard type - 1P+N

Supplying with fitting and fixing Surge protector of max operation voltage 350V at 400 V network for maximum discharge current 40KA with operator indicator and draw out cartridge of (Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the dept. Surge protection Max operating voltage 340V Standard type - 3P+N

Supplying including fitting and fixing of TV SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying including fitting and fixing of following star rated A.C. ceiling fan complete with all accessories like down rod, canopy etc of following sweeps with making necessary connection cable as approved by Deptt.s etc as required complete and as directed by the department as required complete etc. (Without regulator). (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.) Energy efficient 5-star 1200 mm sweep. (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.)

Supplying with fitting and fixing of 120 watt electronic modular STEP speed control 2 - module type MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department. 120 watt electronic modular step speed control 2 - module type

Supplying including fitting and fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making ncessary connections as approved by the Deptt. As required complete as directed by the Department. High Speed 225mm sweep (Orient make), Trans Air 225mm sweep (Crompton make), Ventil Air DX 250 mm sweep Louvere type (Havells make)

Wiring for Co - axial Jelly Flooded (Unarmoured) (FINOLEX /RR KABEL /NICCO / ANCHOR make) cable in existing surface conduit wiring system including connection etc as required. Co - axial Jelly Flooded (Unarmoured) RG 6 (Copper)

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) - 100A

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) - 250A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 40A DP

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 40A TPN

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 63A TPN

Supply, Installation, testing and commissioning of surface mounted LED downlighter fitting, fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.90, an operating Voltage Range of 140 - 270 V.with inbuilt electronic driver, IP-20 rated, Polycarbonate white enclosure with suitable diffuser complete as required.Min lumens 1000Lms. The fixture with BIS certification .Luminair manufacture shall provide LM79report from NABL accredited lab & LM80 report issued by LED manufacturer, Philips make cat no - SM250C LED12S- 6500 PSU WH

Supply, Installation, testing and commissioning of Surface mounted 600mm LED Batten Type luminaire delivering an initial system lumen of 1000 lumens & the luminaire shall be with system efficacy ≥ 100 lm / W. The luminaire Housing shall be made of Extrusion Alu & with HET diffuser. The operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥0.90 , 30,000 Hrs. LED Life with L70 Criteria. Similar to Philips BN021C LED10S.

Supply, Installation, testing and commissioning of Surface mounted 1200mm LED Batten Type luminaire delivering an initial system lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 115 lm / W. The luminaire Housing shall be made of Extrusion Alu & with HET diffuser. The operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 120 to 270V , THD ≤ 15% & PF ≥0.90 , 40,000 Hrs. lamp Life with L70 Criteria. To be supplied with suitable CRCA box type panel. Similar to Philips CNC100 1x18W.

Supplying fitting and fixing of single wall brackets Philips model 37554 (or equivalent as approved by the Deptt.) on the wall in GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover with all accessorei including connection as required complete. (Without lamp)

Supply, installtion, testing & commissioning of 10W LED bulb complete as required.

INCOMMING / OUTGOING Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) - 100A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make). C Series - 63A

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) - 185 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-4 (A2XWY, A2XFY) - 25 sq.mm four core armoured cable

Supply and laying of following size power / control copper cables, solid copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/armoured (Galvanised for cable up to 10x1.5 sq.mm, 8x2.5 sq.mm, 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm, balance all all galvanised steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 4 Core-4, 2XWY, 2XFY - 6 sq.mm four core armoured cable

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor FRLS insulated cable including termination complete as required in existing cable tray. 1C x 35 sq.mm PVC Insulated cu wire including end termination.

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-1/4''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-1/2''

Perforated MT 38 mm SIDE WALL HEIGHT MEDIUM DUTY cable TRAYS HOT DIP GALVANIZED WITH SPLICE- 152

Perforated MT 38 mm SIDE WALL HEIGHT MEDIUM DUTY cable TRAYS HOT DIP GALVANIZED WITH SPLICE - Bend

Perforated MT 38 mm SIDE WALL HEIGHT MEDIUM DUTY cable TRAYS HOT DIP GALVANIZED WITH SPLICE - Inter/Exter Bend

Supply, Installation, Testing & Commissioning of 12 watt LED Mirror Light as complete as required. (Philips Make, Cat No - Mirror Light 32047/11 or equivalent.)

Supply, Installation, Testing & Commissioning of 1x6 watt LED Light recess mounted downlight with high efficiency electronic driver, more than 100 lumens/watt, THD less than 10%, complete as required. (Make : Philips Cat. No. DN295B LED6S-6500 PSU WH or equivalent).

Supply, Installation, Testing & Commissioning of 1x12 watt LED Light recess mounted downlight with high efficiency electronic driver, more than 100 lumens/watt, THD less than 10%, complete as required. (Make : Philips Cat. No. DN296B LED12S-6500 PSU WH or equivalent)

Supply, Installation, Testing & Commissioning of 1x20 Watt LED Light Fixture surface mounted tube light (1200mm) with high efficiency electronic driver, more than 100 lumens/watt, THD less than 10%, complete as required. (Make : Philips Cat. No. BN021C LED20S PSU CW GR S2 or equivalent)

Supply, Installation, Testing & Commissioning of 30 watt LED Light recess mounted square (2'x2') with high efficiency electronic driver, more than 100 lumens/watt, THD less than 10%, complete as required.. (Make : Philips Cat. No. RC380B LED30S-6500 G5 W60 L60 PSU WH OD or equivalent)

Supply, Installation, Testing & Commissioning of 30 watt LED Clean room Light recess mounted square (2'x2') with high efficiency electronic driver, more than 100 lumens/watt, THD less than 10%, complete as required.. (Make : Philips Cat. No.CR652B LED33S CRCW or equivalent)

Supplying, Fitting and fixing of occupany sensor of the following atageories as per required and directed by the department. (ABB/ Panasonic/ mk/ anchor/ crabtree/ Hager/ Panasonic or equivalent make as approved by deptt.Indoor presence detection with 360 degrees angle of detection and 2 relays (one for light and one for HVAC), range up to 7 meter at 2.5 meter ceiling height.

Supply, installation, testing and commissioning of following LAN networks equipments. Solid Copper Cable 6, 4 pair, UTP 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Patch Panel Cat 6 UTP Keystone-24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Patch Cord Cat 6 UTP Gray 1m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation, testing and commissioning of following LAN networks equipments. Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Back Box-(Surface Mount Box) For Single and Dual SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

APW Flexi box wall mount Rack 12U 19" X500 mm D networking wall mount rack with frony tinted glass door with lock PDU 6*5A-01 Nos, Fan 90 cfm 230 Volt-01 Nos, Mounting hardware (Set 0f 10) - 01 set, 19" 1U cable manager-1 nos.

Patch Cord Cat 6 UTP Gray 2m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports . Should support min 2GB internal DRAM, 2GB internal Flash memory,32K MAC address, 1K IPv6 Multicast Routes, Should have static Routes from day 1.One year support. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

FIRE ALARM SYSTEM (ADDRESSABLE TYPE) Supply, Installation,Testing & Commisioning of Microprocessor based X loop fire alarm control panel EN approved expandable upto 12 loops fully networkable with each loop capable of taking 125 devices, 4 line x 40 character alpha-numeric liquid crystal display .The panel shall be soft addressable type . The panel shall be able to give pin point location of all fire/fault conditions. Further, the panel must be able to automatically switch off respective control switches when ever any alarm is triggered. The panel shall have in built rectifier, Loop cards,provision for externel & internal printer(if required), L C D unit to indicate Fire/Fault Signal with address and analog output, built in printer to log all fire or fault events complete in all respects, integral SMF lead acid batteries with sealed cells of 24 V capable of running for a minimum of 8 hours with integral battery charger complete as required and as per specification. The fire alarm panel shall be suitable for software integration with BMS & PA system. 1 Loops

Supply, Installation,Testing & Commisioning of Analog Addressable Intelligent multisensor detector with two inbuilt optical smoke sensors with light angles as well as additional heat detector sensor with decentralise intelligence, soft addressable Photothermal type with inbuilt fault isolator as per NFPA style 7 wiring complete with base as required.

Supply Installation, Testing & Commissioning of Intelligent addressable Manual Call Point / Pull station complete as per specification.

Supply, installation, testing and commissioning of addressable control module complete as per specification.

Supply Installation, Testing & Commissioning of wall mounting loop powered addressable type hooter with all accessories.

Supply Installation, Testing & Commissioning of Response Indicator.

CCTV SYSTEM- Supply, Installation, Testing and Commissioning of UL Listed , ONVIF profile S & G , 1/2.8" CMOS, IP Vari Focal Dome Camera , Full, HD 3 MP , 2.8-12 mm Motorized Varifocal Lens, 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 , Vandal Proof IK10 etc. Approved Makes: Allgovision/ Pelco/ Avigilon/ Impulse/ Axis.

Supply, installation, Testing and Commissioning of Open Platform ONVIF profile S &G Network Video Recorder 8 channel, Intel based, Full Rack, RAID 0/1/5/10, @ 2M/30FPS, 1*2.5" SATA + 8 * 3.5" SATA, Throughput: 640 Mbps.1 X HDMI , 1X VGA ,, 1 X mic in , 1 X line out , USB 3.0 x 2 + USB 2.0 x 3 , 1 X WAN port , 1 X LAN port , pre-installed VMS :Approved Makes :Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply, Installation, Testing & Commissioning of 4TB HD Approved Makes: WD, Segate / Toshiba.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit. Approved Makes: HP, Dell, IBM.

UPS SYSTEM Supply, installation, testing & commissioing of 40 KVA UPS at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, inbuilt isolation transformer at invertor output before static switch as per specification given in the document with following broad features. (Make-Reillo Power/Mitsubishi/APC/Socomec) a) THD(i) shall be less than 3% in the entire loading range. b) UPS shall carry design output at 40 deg. c) Shall have soft start and hold of for incoming supply. d) Invertor capability to supply 150% load for 5 sec. e) Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. g) Battery shall be external type with rack and suitable for 30 minute backup on 100% load. Suitable size & length of Copper Cable between battery to battery and battery to UPS shall be provided without any extra cost. UPS described as above

DG SET WORK- Supplying, including installation. Testing and commissioning of Air / Water Cooled Jackson (Cummins) Diesel Generator set coupled to suitable alternator of 415 V, AC, 3-Phase 0.8 p.f. mounted on a 1) M.S. fabricated base frame., 2) M.S. fuel tank of required capacity., 3) Residual Silencer., 4) AMF/Standard Control Panel. 5) Suitable batteries with lead., 6) First fill of Lube oil., 7) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification as per manufacturer. 140-3-4040x1450x1900 3500 Kg W/C

EXHAUST PIPING Supply, Installation, Testing and Commissioning of following sizes MS exhaust piping heavy duty conforming to IS:3589 complete with all accessories such as bends, flanges, stainless steel flexible bellows etc. as required. 100 mm dia MS pipe. (5.0 mm thick)

Providing & Fixing of Insulation and cladding for exhaust piping using 75 mm thick rockool of density 150 Kg/ M3 & 24 SWG Aluminium Sheet.

Fabrication, supply & erection of MS structure for supporting of DG emission, exhaust piping with RCC foundation etc. complete in all respect.

TELEPHONE SYSTEM Supplying ,installation, testing & commissioning of 2 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying ,installation, testing & commissioning of Distribution Box 50 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Supplying with fitting and fixing of RJ-11 Telephone jack , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

EARTHING Supply with installation & commissioning of readymade maintenance free CPRI approved chemical earthing system with 50mm dia. 3.00 Meters length corrosion free dual pipe technology G.I. Chemrode Electrode complete with Reslow grounding Minerals 25 k and Advance Earth pit cover including excavation of earth pit and construction of brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the deptt.

Supply with installation & commissioning of readymade maintenance free CPRI approved chemical earthingsystem with 50mm dia. 3.00 Meters length corrosion free Single pipe technology -Copper Chemrode Electrode complete with Reslow grounding Minerals 25 k and Advance Earth pit cover including excavation of earth pit and construction of brick earth chamber including plastering both inner &outer surface of brick wall as specified and directed by the deptt.

Supplying &laying of 6 SWG G.I. Earth from earth electrode (below G.L.)to electrical swicth gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 25x6 mm size G.I. strips drawn on surface from earth electrode to electrical switch gears , machineries etc.complete with supply of G.I. nuts & bolts screws etc including reverting, soldering & making necessary connection as approved,specified and directed by the deptt.

Supplying & laying of 25x5 mm size Copper strips drawn on surface from earth electrode to electrical switch gears , machineries etc complete with supply of brass nuts & bolts screws etc including reverting, soldering & making necessary connection as approved,specified and directed by the deptt.

Supplying, instalation, testing and commissioning of Anti Microbial Coated construction, DIN VDE 0834 approved Hospital Communication System comprising of video streaming ready future oriented open technology plateform for all communication task and services like IP telephony,Smart card system,electro accoustic function and internet and internet services using its own Communication LAN and highest level of security against system failure, comprising of the following as required:- (Makes - Shrack / Rauland / Tunstall). VDE 0834 certified/ approved System Switch: S.I.T.C. of Main Controller system switch that forms a decentralised communications node for exchanging data between the connected system devices and the rest of the communications system, consisting of 1 x RJ45 socket, 100Mb IP Port (IEEE802.3 100BaseTX), galvanically isolated conforming to EN 60950 and VDE 0834, 7 x RJ45 sockets, each for a 100Mb IP system port (IEEE802.3 100 BaseTX) for connecting all IP capable system modules, 1 x RJ45 socket, 100Mb IP Port (IEEE802.3 100BaseTX) for connecting communications, staff and ward terminals as well as control panel PCs or for redundant Connection, Control LEDs for indicating the current operating state, 2 x RJ45 sockets for connection of the external data bus, all IP system modules supplied with power using Power over LAN technology using its own communication LAN complete as required including event data base software to recall all calls generated by the patient and nursing staff with date and time.

Supplying, instalation, testing and commissioning of Anti Microbial Coated construction, DIN VDE 0834 approved Hospital Communication System comprising of video streaming ready future oriented open technology plateform for all communication task and services like IP telephony,Smart card system,electro accoustic function and internet and internet services using its own Communication LAN and highest level of security against system failure, comprising of the following as required:- (Makes - Shrack / Rauland / Tunstall). VDE 0834 certified/ approved Nurse Station Terminal:S.I.T.C. of Nurse Station Ward Terminal comprises of 5.6 “LC display for displaying all details, a smash proof glass panel (to protect the sensitive display from unnecessary contact during cleaning and other processes) , function keys for operating the system, Querying receiver for speaking discretely, Microphone and loudspeaker for hands-free speech (incl. volume control), automatic changeover between hands-free and discrete speaking , Electronic circuit board with controller and FlashProm, 100BaseTX interface to the system switch, 2.8m connection cable with an RJ45 connection plug, which is protected, from disconnection, for connecting to a connection module. The ward terminal shall display date and time, indication of all presence, all set reminedrs, indication of all calls in accordance with VDE0834. All call indications follow the priority and must display the exact location of the calls. The ward terminal shall be provided along with suitable connection module & back box. It should be supplied along with connection module & its back box for installation complete as required.

Supply, Installation, Testing & Commissioning of VDE 0834 certified/ approved Patient Handset Without Speech consisting of a plastic case in antimicrobial finish having Call button with nurse symbol with integrated finder and reassurance light on the top end of the unit, Membrane keypad in antimicrobial finish with integrated LEDS for operation, 1 call key, 2 lighting keys, 2.80 metre connection cable with auto-disconnecting RJ45 connector plug. It shall be supplied with cradel for holding patient terminals etc and as per tender technical specification.

Supply, Installation, Testing & Commissioning of VDE 0834 certified/ approved connection module for Patient Terminal. Connection module for patient handset shall consist of 1 x RJ45 socket marked in colour and with measures to ensure that the push button is correctly connected, including auto disconnect mechanism, 1 membrane keypad with 1 call button (red with nurse symbol) including a finder/reassurance light, 1 presence key/ cancel button (green) including a control LED etc and as per tender technical specification.

Supply, Installation, Testing & Commissioning of VDE 0834 certified/ approved Loop Powered Lamp Module. For optical indication of calls, presences and reminders in the relevant colours conforming to VDE0834 consisting of 5 light chambers with light reflectors for homogeneous illumination, 1 light chamber fitted with 3 ultra bright red LEDs, 1 light chamber fitted with 3 ultra bright white LEDs, 1 light chamber fitted with 3 ultra bright green LEDs, 1 light chamber fitted with 3 ultra bright blue LEDs, 1 light chamber fitted with 3 ultra bright Yellow LEDs, 2 RJ45 ports for loop connectivity etc and as per tender technical specification.

Variable Refrigerant Volume / Flow Air-conditioning System Supply, Instalaltion, testing and commissioning of Variable Refrigerant Flow /Volume (VRF/VRV) (with the latest technology/version) with All-Inverter driven Compressor, modular type airconditioning system with stepless modulation for both heating & cooling modes, complete with indoor and outdoor units, individual remote controller and centralized controller, interconnected refrigerant piping with insulation, Y joints, full charge of refrigerant gas including additional top up and oil, control cabling etc. as per detail given in specifications and having following items. The prices to be given in Indian rupees including all taxes and duties and delievered at site. Refrigerant to be used shall be - R 410 A only. It shall be complete as per specifications,with connectivity to automation for A/M status, RUN status & Remote start/stop command.(Bacnet/IP) with multi connection kits for each outdoor unit & First charge of refrigerant gas for the VRF/VRV Units & required MS frame work or required foundation & anti vibration pads for mounting the outdoor units. installation, testing & commissioning of air cooled VRV/VRF system shall include pipe pressure testing & flushing with nitrogen, charging of gas/oil etc. & will include all lifting/shifting etc. Air Cooled VRV / VRF Outdoor Unit Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at50°Cambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . Minimum. 26 H.P Cool / Heat Pump Unit

Expansion Kit, Communication PCB & Thermostat Supply, Installation, Testing & Commissioning of Electronic Type Expansion Kit, Communication PCB with Sensors, Corded Self Diagnostic Type Digital Thermostat, Controller, control box with internal wiring, AHU kit for each DX Type Units and other related accessories etc with connectivity to automation system for A/M status, RUN status & Remote start / stop command (Bacnet/IP). It should be complete as per manufacturing standards & as per directions of Engineer-in-charge. For 6000 CFM F/M AHU with 2 x 32.0 HP VRV ODU

Double Skin Floor Mounted VRV DX AHU 100% Fresh Air Supply, installation, testing and commissioning of factory fabricated Double Skin VRV DX Air-handling unit Floor mounted type fabricated out of extruded aluminium section with 0.8 mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), and blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 8 Row cooling coil made of Aluminium finned Copper tube with coil section, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, Coilotron UV section only of 600 mm in length in floor mounted AHU, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 48mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to specication & face velocity across cooling coil shall be limited to 152 MPM maxm. AHU DX coils shall be in tune with the requirement of VRV Outdoor Unit capacity and no divisions shall be made in cross sectional area of the coil. If multiple ins and outs of refrigerant pipe are required then coils shall be grouped into required rows keeping the cross sectional area of the coil constant. The capacity of Air-handlers shall be as follows: VRF/AHU/1 - 5,000 CFM Supply Air, 8 Row CC, 80 mm St. Pr., with other accessories as specified)

Double Skin Ceiling Mounted Exhaust Air Fan Section (MEU - Mechanical Exhaust Unit) Supply, installation, testing and commissioning of factory fabricated Double Skin Exhaust Air Fan Section ceiling mounted type fabricated out of extruded aluminium section with 0.8 mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside with forward curved blower, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The MEU panels shall be insulated with 23mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The capacity of MEU shall be as follows: MEU/1 - 6,500 CFM Supply Air, 40 mm St. Pr., with other accessories as specified)

AHU Mounted Coilotron UV System For Floor Mounted AHU Supply, installation, testing and commissioning of AHU mountable self contained and factory assembled Coilotron UV System with UL 1995 ABQK listed and UL 2043 certified, UV lamp life shall not be less than 11000 hours. Coilotron shall be installed in all floor mounted AHUs as specified herein. All the component / parts shall comply with the specification given in the tender. AHU supplier and coilotron supplier shall co-ordinate with each other regarding the fixing of the same in the AHU. For 2,000 to 8,000 CFM AHU

Refrigerant Piping for VRV / VRF System Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Refrigerant Piping for VRV / VRF System Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with "O" class Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 40 mm dia pipe , 19 mm Insulation

Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 G (Up To 750 mm)

Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 22 G (751 to 1500 mm)

Site Fabricated GI Ducting Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required a) 24 G (Up To 750 mm)

Site Fabricated GI Ducting Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required b) 22 G (751 to 1500 mm)

Duct Accoustic Lining Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Duct Insulation Supplying and fixing of external thermal insulation on ducts with EPDM Rubber foam with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000, tape & adhesive (pidilite SR -998) as required of following thickness. 13 mm

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Fresh / Exhaust air louvers with bird screen & damper

Volume control GI Dampers to be provided in supply & Exhaust air registers / terminals.

Isolator Switch With Metal Enclosure For 40 HP ODU (IP-65) 100A 4 pole RCBO for VRV Outdoor Units with sheet metal enclosure, rain protection etc. as required to suit the site condition.

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor Up to 3.73 Kw 1 x 3C x 4 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor of 5.5 Kw 1 x 3C x 6 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For VRV ODU Unit (From Panel to Isolators near ODU) 1 x 3C x 16 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For VRV ODU Unit (From Panel to Isolators near ODU) 1 x 3C x 25 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For VRV Outdoor (From Isolators to Unit) 1 x 3 C x 6.0 Sq. mm Copper Flexible Cable

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For VRV Outdoor (From Isolators to Unit) 1 x 3 C x 10.0 Sq. mm Copper Flexible Cable

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. B) Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 3C x 1.5 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. B) Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 4C x 1.5 Sq. mm

C) Transmission & Control Wiring For VRV System Providing & fixing of control cum trans-mission wiring of copper between indoor and out door unit in 25 mm PVC Conduit. 3C / 2C x 1.5 Sq mm

Earthing Strip / Wires as per specs. Supply & laying of 8 SWG GI wire or in recess for loop earthing as required.

Supply & laying of 6 SWG GI wire or in recess for loop earthing as required.

Supply & laying of Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.

Supplying and installing following size of perforated GI cable trays including bends. tee, reducers etc with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including bolts & nuts, suspenders etc as required. 150 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated GI cable trays including bends. tee, reducers etc with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including bolts & nuts, suspenders etc as required. 300 mm wide x 50 mm depth x 1.6 mm thickness.

Supply, installation, testing & commissioning of Magnehelic Differential Pressure Gauge having measuring accuracy of 3%

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 100 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 150 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 200 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 250 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 300 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 350 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 400 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 450 CFM

5Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 00 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 600 CFM

Supply, installation, testing & commissioning of Constant Air Volume Boxes as per specification & capacity as given below:- 700 CFM

Industrial Drying Tumbler. Front Loading, Open Pocket, Steam Heated, 30 kg Capacity.

Flat Work Drying Ironer 1 roll, Heated Chest Type, Front Feed, Rear return, Steam Heated.

Washroom Trolley. S.S. 50kg capacity , Overall Size : 1000 x 600 x 780 ht.

Dry Linen Trolley. S.S. 50kg capacity , Overall Size : 1100 x 600 x 1500 ht.

Shelf Trolley. S.S. 100kg capacity , Overall Size : 1200 x 600 x 1700 ht.

Mobile Table. S.S. Top Size : 1150 x 750

Vacuum Finishing Table. 1200 x 750, Electric Steam Iron Teflon Shoe, aluminium armoured & spring loaded , Condensate Separator

Industrial Washer Extractor. 30 kg Capacity, High Spin, Suspended, Computer Controlled, Steam Heated.

Air Compressor 2 HP Single Stage with100 ltrs Tank

Horizontal rectangular High Pressure High Vacuum Steam Sterilizer, Radial Hinged Double door, Inner chamber size: 450mm width x 450mm height x 1200mm length, 200-250 litres volume, fully automatic cycle operation with printer, electrical operated , as per technical specification

Washer disinfector with inbuilt drier,Double door, 250-275 litres capacity, as per technical specification

Ultrasonic V cleaner 30 litres capacity, as per technical specification

Strainless steel work table with double sink, as per technical specification

Spray Gunriser with eight attachments, as per technical specification

Stainless steel control and packing table with drawer, as per technical specification

Strainless steel work table with undershelf, as per technical specification

Table mounted heat sealing machine, as per technical specification

Stainless steel Table Mounted Gauze cutting machine, as per technical specification

Stainless steel Pass Box, Double door, size: 600mm x 600mm, as per technical specification

Stainless steel Storage Rack with 5 shelves, as per technical specification

PRE ENGINEERED BUILDING SHED Wall (10’ht)- 50mm Aerocon/Vishakha Panel made of cement both sheet & portland cement inside; held on U Section or 8mm Cement board in boath side with thermocole insulation Roof- PPGI 0.45mm Colour Coated Sheet (Ultrashine/Essar/Asian) , Structure - (For Trush 2”x2”, Column 4”x2”, Purline 1.6” x 1.6”) False Ceiling – Gypsum/CFB Board 600x600 with T Grid Paint - (Asian Make) as per choice of Client, it will be range of Apex Rate Window - Aluminium Sliding Window 4’x3’ with Grill Door – Flush Door 7’x3’ Main Door – Aluminium Door half Glass/Half MDF Board Door 7’x4’’ Wiring - (Indomax/Anchor/I.S.I Mark) on Smart Modular switches fitting Toilets (EWC/WB (Cera/Parryware/I.S.I) and all fitting arrangement in PVC as per drawing, Urinal 02 Nos with fitting Bio Tank With Fitting Water Tank 1000 Ltr with Water Tower Foundation 0ne feet deep and one feet height Vetrified Floor Tiles of approved make all above complete as per approved design and as per direction of Engineer-in-charge.

Supplying installation testing commissioning of Bio-medical waste disposal system suitable for use in Covid ICU for disposal of all types of Hospital waste like PPE Kits, face mask, Gloves, etc. having capacity of 20Kg/hour strictly conforming to CPCB norms.

Providing, Fabricating and fixing of Hospital Cubicle Track System comprising of the following components and specifications: 1. CUBICLE TRACK Made of Metal Aluminum Alloy of Box size 1.7 x 20 x 25 mm with 50-60 microns thick powder coating in white color finish. Tracks are bendable to a radius of 300 mm at 90 degree to cover the whole bed. 2. CURTAIN Made of premium quality Stain Proof fabric with High quality Nylon Net of 18” and 24” on top. 3. SUPPORTING SYSTEM OF CONSISTS OF THE FOLLOWING MATERIAL: Wall Bracket- Made of CRC steel with white powder coating finish. I. Bride Clamp- Made of CRC steel with white powder coating finish. II. Roof Suspension- Made of aluminum pipe of 12.5 mm & 19.5 mm diameter. The Upper Circular Plate made of aluminum with 50.4mm diameter thickness. These are with white powder Coating (outer surface) finish & are of variable height fixed with the ceiling with anchors, bolts, screws etc. 4. CURTAIN REMOVABLE POINT- Made of SS for simple loading & unloading of curtains. (Also serves as an end hook retainer). 5. Runner- Comprises of wheel type runners made of Teflon for easy and smooth sliding of the curtain. all complete as per Direction of Engineer-in-charge.

MEDICAL OXYGEN SYSTEM Supply, installation, testing & commissioning of Oxygen Manifold with 8 Nos. pigtailpipes for 2+2 cylinders and Non-returnvalves, as per enclosed technical specifications and approved make (without cylinders)

Supply, installation, testing & commissioning of Fully Automatic Oxygen Contr0l Panel, as per HTM-2022/02-01ofUK/NFPA99C of USA as per enclosed technical specifications and approved make

Supply, installation, testing & commissioning of Oxygen Manifold Emergency for 2 Cylinders, as per enclosed technical specifications and approved make- (without cylinder)

Supply, installation, testing & commissioning of Oxygen Outlets with matching probes, CE certified with four digit notafied number as per enclosed technical specifications and approved make- (Imported)

Supply, installation, testing & commissioning of Oxygen Flowmeter with Humidfier Bottle CE Certified with four digit notafied number /UL Listed,as per enclosed technical specifications and approved make - (Imported) for critical area

VACCUM SYSTEM Supply, installation, testing & commissioning of Duplex Vacuum central system with Duplex pump only complete with electrical control panel as per enclosed tender specification and approved make sufficient for 15 bed

Supply, installation, testing & commissioning of Vacuum Outlets with matching probes, CE certified with four digit notafied number as per enclosed technical specifications and approved make- (Imported)

Supply, installation, testing & commissioning of Ward Vacuum unit CE Certified as per enclosed tender specification and approved make

MEDICAL COMPRESSED AIR SYSTEM Supply, installation, testing & commissioning of Duplex Air Compressor complete with Compressed air plant complete as per enclosed technical specification and approved make sufficient for 15 bed

Supply, installation, testing & commissioning of Air-4Bar Outlets with matching probes, CE with four digit notified number as per enclosed technical specifications and approved make-(Imported)

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Kite Marked COPPER PIPE 12mm

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Kite Marked COPPER PIPE 15mm

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Kite Marked COPPER PIPE 22mm

Supply, installation, testing & commissioning of MEDICAL Grade BS EN: 13348 Kite Marked COPPER PIPE 28mm

Supply, installation, testing & commissioning of Medical Area Line Pressure Alarm -as per HTM 2022/02-01/ NFPA99C as per enclosed technical specifications and approved make Area Line pressure Alarm-3 gases

Supply, installation, testing & commissioning of Medical Area Valve Service Unit ( Valve Box with isolation valve) as per CE certified/UL listed as per enclosed technical specifications and approved make 3 Gases

Supply, installation, testing & commissioning of Aluminum extruded Bedhead Panel long four feet with electrical & provision of gas outlet as per enclosed technical specifications and approved make

Supply, installation, testing & commissioning of Electrical Panel for Air compressor &Vaccum Pump as per enclosed technical specifications and approved make

Supply, installation, testing & commissioning of High Pressure hose as per enclosed technical specifications and approved make

Any other unseen item of work which are not covered in this BOQ that may be required at site during execution having an estimated provision of Rs.92,87,589.00 (Including GST). The rate for the items will be finaliased as per current APWD SOR/ Market Rate Analysis etc. in proportion to the quoted amount and the estimated amount. Note:- The amount against this item has been kept as a provission for any unforseen/ additional items of works which may arraise during the execution of the work. A Lump sum rate is to be quoted against these items which shall not be less than 10% below. Bids not complying to this shall summarily be rejected.