REP/REPLACEMENT OF UNSV SPARES OF DRYING TUMBLER-60KG, WASHRER EXTRACTOR-120KG, FLAT BED PRESS, GEN UTILITY PRESS, FLAT WORK IRONER AND COMPRESSOR OVERHAULING AT MECHANICAL LAUNDARY PLANT AND REP/MAINT OF COLD CHAMBERS AT MAIN MEDICAL STORE AT BASE H

Amount

Disconnecting electric/Steam connection of Drying Tumbler 60 kg capacity/ Dry Cleaning Machine, Make- fabcare from press to carry out day to day/ breakdown maintenance of the press and remove all dust and sand particles, providing oil and grease to all moving parts including greasing of motors bearings etc checking all loose electrical connections and tightening all electrical connection with thimble and commissioning after refixing it at original position and put equipment in fully functional conditions all as specified and directed by Engr-in-Charge. Note :- All major spares and material required to fix in General Utility Press for put it functional will provide against respective items.

Taking down of unserviceable spare parts of Drying Tumbler- 60Kg capacity, Make- FABCARE, comprising, dismantling of the equipments using adequate labour and T&P for disconnecting steam / water connection and electrical connection, defective spare parts / items and carrying out necessary Major overhauling as required, including cleaning, servicing, oiling, greasing, weilding work, polishing etc, making all water/ steam connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of each equipment suitable for Drying Tumbler, Make- FABCARE, Model-DTS 60, capacity-60kg at optimum efficiency as per the standard. Note:- (1) Spare parts to be replaced shall be measured and paid under the following respective parts. ( Sr no. 2.01 to 2.24) (2) Contactor should produce OMU of agreement between OEM & contractor firm from whom contractor should carried out the major overhauling of Drying Tumbler which is fabcare (3) Contractor should arrange necessary T & P and Man power to take out unsv Drying Tumbler major overhauling and refixing the same a existing position after overhauling all as specified and directed by Engr-in-charge. The quoted rate inclusive of all and no extra cost admissible in this regard.

Supply only Steam Heating Coils Copper Tube Alu. FINS

Supply only Main Drive V.Belts, Make - FENNER/DUNLOP/NAVYUG

Supply only Main Idler V.Belts, Make - FENNER/DUNLOP/NAVYUG

Supply only Steam Trape

Supply only Bye Pass Assembly S.S. Ball valves

Supply only Automatic Steam inlet valve

Supply only Main Drive 2 Bearing + 2 pcs Sleeves

Supply only Main IDLER Bearing + 4 pcs

Supply only Pneumatic Pipes & Fittings

Supply only Alu. Blowers for Suction

Supply only Glass with rubber Packing and S.S. screws

Supply only Rubber Packing for lint screen

Supply only Door Latches for lint screen

Supply only Door Limit Switch

Supply only MCB Make- HAVELLS/L&T/STANDARD.

Supply only Timer 0 - 60 , MAKE- L&T/ HAVELLS/

Supply only Timer Rev - Fwd

Supply only contactor

Supply only MPD

Supply only DTC (Digital Temp. Controller)

Supply only Thermo Couple

Supply only Push Button Green

Supply only Ind. Light

Supply only Red push button

Disconnecting electric/Steam connection of Flat Work Ironer, Size-830MM X 3300MM, Make- fabcare from press to carry out day to day/ breakdown maintenance of the press and remove all dust and sand particles, providing oil and grease to all moving parts including greasing of motors bearings etc checking all loose electrical connections and tightening all electrical connection with thimble and commissioning after refixing it at original position and put equipment in fully functional conditions all as specified and directed by Engr-in-charge. Note:- All major spares and material required to fix in Flat Work Ironer, Size-830MM X 3300MM for put it functional will provide against respective items.

Taking down of unserviceable spare parts of Flat Work Ironer, Size-830MM X 3300MM, Make-FABCARE comprising, dismantling of the equipments using adequate labour and T&P for disconnecting steam / water connection and electrical connection, defective spare parts / items and carrying out necessary Major overhauling as required, including cleaning, servicing, oiling, greasing, weilding work, polishing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of each equipment suitable for Flat Work Ironer, Make- FABCARE at optimum efficiency as per the standard. Note:- (1) Spare parts to be replaced shall be measured and paid under the following respective parts. ( Sr. no. 4.01 to 4.33) (2) Contactor should produce OMU of agreement between OEM & contractor firm from whom contractor should carried out the major overhauling of Flat work Ironer which is fabcare. (3) Contractor should arrange necessary T & P and Man power to take out unsv Flat work Ironer major overhauling and refixng the same a existing position after overhauling all as specified and directed by Engr-in-charge. The quoted rate inclusive of all and no extra cost admissible in this regard.

Supply only Polyester Padding

Supply only Flannel Cloth

Supply only Final Cover

Supply only Conveyor Belts Imported with hook & pin as spare

Supply only Guide Tape

Supply only Main Bearing Set Roller (2 Pcs. = 1 Set)

Supply only Flexible S.S. Hose Pipes (3 Pcs. = 1 Set)

Supply only VFD, Make- DELTA/L&T/YASHKAWA

Supply only V-Belts, Make - FENNER/DUNLOOP/NAVYUG

Supply only FRL

Supply only Pneumatic Fitting & Pneumatic Pipe

Supply only MCB, 32 Amp TPN, 10KA 415Volt, Make- L&T/HAVELLS/STANDARD

Supply only Push Button

Supply only Ind. Light

Supply only Temp. Meter

Supply only Thermo Couple

Supply only Gripper for Duffle Roll

Supply only Steam Trape

Supply only Ball Valve for Steam Trape

Supply only Limit Switch

Supply only Pressure Guage

Supply only Air Regulator Front Side

Supply only Contactor

Supply only Single Phase Preventer

Supply only O/L Relay

Supply only 4" Flexible pipe blower Exhaust

Supply only Solenoid Valve

Supply only Main Pneumatic Air Cylinder

Supply only Main Motor

Supply only Blower Motor

Supply only Gear Box

Supply only Main Gear + Pinion Set

Supply only Angle Valve for Steam Inlet

Disconnecting electric/Steam connection of Vacuum steam Ironing Finishing Table machine, Make- fabcare from press to carry out day to day/ breakdown maintenance of the press and remove all dust and sand particles, providing oil and grease to all moving parts including greasing of motors bearings etc checking all loose electrical connections and tightening all electrical connection with thimble and commissioning after refixing it at original position and put equipment in fully functional conditions all as specified and directed by Engr-in-charge. Note:- All major spares and material required to fix in Vaccum steam Ironing Finishing Table machine for put it functional will provide against respective items.

Taking down of unserviceable spare parts of Vaccum steam Ironing Finishing Table machine, Make FABCARE, comprising, dismantling of the equipments using adequate labour and T&P for disconnecting steam / water connection and electrical connection, defective spare parts / items and carrying out necessary Major overhauling as required, including cleaning, servicing, oiling, greasing, weilding work, polishing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of each equipment suitable for Vaccum steam Ironing finishing table machine, Make- FABCARE, MODEL- FIB 42 at optimum efficiency as per the standard. Note:- (1) Spare parts to be replaced shall be measured and paid under the following respective parts. ( Sr no. 6.01 to 6.28) (2) Contactor should produce OMU of agreement between OEM & contractor firm from whom contractor should carried out the major overhauling of Vaccum steam Ironing Finishing Table Machine which is fabcare (3) Contractor should arrange necessary T & P and Man power to take out unsv Vaccum steam Ironing Finishing Table Machine major overhauling and refixng the same a existing position after overhauling all as specified and directed by Engr-in-charge. The quoted rate inclusive of all and no extra cost admissible in this regard.

Supply only SINGLE SOLENOID VALVE 1/4 CEME FOR TABLE

Supply only HAND IRON 2128 MODEL

Supply only HEAVY IRON OF TI 125

Supply only CONTACT BLOCK 1NO+1NC , Make- L&T / SIEMENS/LEGRANDS

Supply only CONTACT BLOCK 2NO+2NC , Make- L&T / SIEMENS/LEGRANDS

Supply only CONTACTOR 9A , Make- L&T / SIEMENS/LEGRANDS

Supply only CONTACTOR 18A , Make- L&T / SIEMENS/LEGRANDS

Supply only CONTACTOR 25A , Make- L&T / SIEMENS/LEGRANDS

Supply only CONTACTOR 32 A , Make- L&T / SIEMENS/LEGRANDS

Supply only CONTACTOR 40 A , Make- L&T / SIEMENS/LEGRANDS

Supply only DOOR GASKIT , Make- L&T / SIEMENS/LEGRANDS

Supply only FRL 1/4

Supply only FRL 1/2"

Supply only INDGATING LIGHT

Supply only INDGATING LIGHT CLEAR

Supply only LIMIT SWITCH

Supply only MPD 0-10

Supply only MPD 7-20

Supply only PNEUMATIC ACTUATOR FITTED BUTTER FLY VALVE 2" ROTEX

Supply only PRESSURE SWITCH

Supply only PUSH BUTTON

Supply only REVERSING TIMER ANALOG TYPE

Supply only SINGLE SOLENOID VALVE 1/4

Supply only SS CASTING BALL VALVE FOR STEAM INLET 1/2"

Supply only SS CASTING BALL VALVE FOR STEAM INLET 3/4"

Supply only TEMPRATURE METER 72 X 72

Supply only THERMO CUPLE 3MTR

Supply only THERMO CUPLE 5MTR

Disconnecting electric/Steam connection of Flat Bed Press,, Make- Fabcare from press to carry out day to day/ breakdown maintenance of the press and remove all dust and sand particles, providing oil and grease to all moving parts including greasing of motors bearings etc checking all loose electrical connections and tightening all electrical connection with thimble and commissioning after refixing it at original position and put equipment in fully functional conditions all as specified and directed by Engr-in-charge. Note:- All major spares and material required to fix in Flat Bed Press, for put it functional will provide against respective items.

Taking down of unserviceable spare parts of Flat Bed Press, Make FABCARE, comprising, dismantling of the equipments using adequate labour and T&P for disconnecting steam / water connection and electrical connection, defective spare parts / items and carrying out necessary Major overhauling as required, including cleaning, servicing, oiling, greasing, weilding work, polishing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of each equipment suitable for Flat Bed Press, Make - FABCARE, Model-FBS 30 at optimum efficiency as per the standard. Note:- (1) Spare parts to be replaced shall be measured and paid under the following respective parts. (Sr no. 8.01 to 8.16) (2) Contactor should produce OMU of agreement between OEM & contractor firm from whom contractor should carried out the major overhauling of Flat Bed Press which is fabcare (3) Contractor should arrange necessary T & P and Man power to take out unsv Flat Bed Press major overhauling and refixng the same a existing position after overhauling all as specified and directed by Engr-in-charge. The quoted rate inclusive of all and no extra cost admissible in this regard.

Supply only Temp. Meter

Supply only Thermo Couple for Temp. Meter

Supply only Toggle Switch

Supply only Contactor

Supply only GIC Timer

Supply only Solenoid Valve 1/2"

Supply only Flow Control Valve

Supply only Silencer

Supply only Silencer with Flow Control Valve

Supply only FRL 1/2"

Supply only Padding with final cloth

Supply only Air Flexible Pipe

Supply only Steam Angle Valve

Supply only Solenoid Valve for Angle Valve

Supply only Spring

Supply only Oil Seal for Air Cylinder

Disconnecting electric/Steam connection from General Utility Press Make- fabcare from press to carry out day to day/ breakdown maintenance of the press and remove all dust and sand particles, providing oil and grease to all moving parts including greasing of motors bearings etc checking all loose electrical connections and tightening all electrical connection with thimble and commissioning after refixing it at original position and put equipment in fully functional conditions all as specified and directed by Engr-in-charge. Note:- All major spares and material required to fix in General Utility Press, for put it functional will provide against respective items.

Taking down of unserviceable spare parts of General Utility Press, Make FABCARE, comprising, dismantling of the equipments using adequate labour and T&P for disconnecting steam / water connection and electrical connection, defective spare parts / items and carrying out necessary major overhauling as required, including cleaning, servicing, oiling, greasing, weilding work, polishing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of each equipment suitable for General Utility Press, Make- FABCARE, Model- FUPS at optimum efficiency as per the standard. Note:- (1) Spare parts to be replaced shall be measured and paid under the following respective parts.(Sr. no. 10.01 to 10.19) (2) Contactor should produce OMU of agreement between OEM & contractor firm from whom contractor should carried out the major overhauling of General Utility Press which is fabcare. (3) Contractor should arrange necessary T & P and Man power to take out unsv General Utility Press major overhauling and refixng the same a existing position after overhauling all as specified and directed by Engr-in-charge. The quoted rate inclusive of all and no extra cost admissible in this regard.

Supply only Temp. Meter

Supply only Thermo Couple For Temp. Meter

Supply only Green Push Button

Supply only Red Push Button

Supply only Indicating Light

Supply only Toggle Switch

Supply only Contactor Make- L&T / SIEMENS/LEGRANDS

Supply only GIC Timer

Supply only Solenoid Valve 1/2"

Supply only Flow Control Valve

Supply only Silencer

Supply only Silencer with Flow Control Valve

Supply only FRL 1/2"

Supply only Padding with Final Cloth

Supply only Air Flexible Pipe

Supply only Steam Angle Valve

Supply only Solenoid Valve for Angle Valve

Supply only Spring

Supply only Oil Seal for Air Cylinder

Disconnecting electric/Steam connection of Washer Extractor-120 Kg Make- fabcare from washer extractor to carry out day to day/ breakdown maintenance of the press and remove all dust and sand particles, providing oil and grease to all moving parts including greasing of motors bearings etc checking all loose electrical connections and tightening all electrical connection with thimble and commissioning after refixing it at original position and put equipment in fully functional conditions all as specified and directed by Engr-in-charge. Note:- All major spares and material required to fix in Washer Extractor-120 Kg for put it functional will provide against respective items.

Taking down of unserviceable spare parts of Washer Extractor-120 Kg, Make FABCARE, comprising, dismantling of the equipments using adequate labour and T&P for disconnecting steam / water connection and electrical connection, defective spare parts / items and carrying out necessary Major overhauling as required, including cleaning, servicing, oiling, greasing, weilding work, polishing etc, making all water/steam connection and electrical connection, leak testing at desired pressure, with and including testing, commissioning of each equipment suitable for Washer Extractor, Model- AWXS 120, capacity-120kg at optimum efficiency as per the standard. Note:- (1) Spare parts to be replaced shall be measured and paid under the following respective parts ( Sr. no. 12.01 to 12.32) (2) Contactor should produce OMU of agreement between OEM & contractor firm from whom contractor should carried out the major overhauling of Washer Extractor which is fabcare. (3) Contractor should arrange necessary T & P and Man power to take out unsv Washer Extractor capacity -120 kg major overhauling and refixng the same a existing position after overhauling all as specified and directed by Engr-in-charge. The quoted rate inclusive of all and no extra cost admissible in this regard.

Supply only V Belt, Make - FENNER/DUNLOP/NAVYUG

Supply only VFD, Make- DELTA/L&T/YASHKAWA

Supply only Display Controller (AXW Controller)

Supply only Single Solenoid Valve

Supply only Main Water Inlet Valve (Actuator Butterfly Valve), MAKE- SANT/AUDCO/KARTAR

Supply only Main Drain Valve (Actuator Butterfly Valve), MAKE- SANT/AUDCO/KARTAR

Supply only Main Steam Inlet Valve Automatic

Supply only S.S Flexible Hose (For Steam Inlet)

Supply only S.S Flexible Hose 2" (For Water Inlet for back side of M/c at the time of tilting)

Supply only Main Drive Alu.Pulley

Supply only Main Bearing Set

Supply only Main Bearing Seal Set

Supply only Main Bearing Circlip

Supply only Pneumatic Fitting (Tee , Elbow , Connector)

Supply only Pneumatic Pipe

Supply only Hose Pipe ( JK pipe 4"

Supply only Hose Pipe ( JK pipe 2 ¼")

Supply only Clamps 4" Heavy Fabricated S.S

Supply only Clamps 2"

Supply only Air Vent Pipe (JK pipe 2 ¼")

Supply only FRL Set

Supply only S.S Screws (For Main Cover)

Supply only Teflon Tape

Supply only Pneumatic Cylinder Door LOCK

Supply only L N Key Bolt for main Housing

Supply only Main Shocker

Supply only Main Springs heavy

Supply only Main Door Glass Toughned

Supply only Door Lock Latch Handle

Supply only MCB 40 Amp, TPN , 10KA 415 Volt, Make- L&T/HAVELLS/STANDARD

Supply only Thermo Couple

Supply only Door Gasket

M&L for repairing/servicing (rewinding) of three phase induction motor/ blowers motor, capacity-1HP, single phase motor, Make- ABB or existing motor make & Including the following jobs:- (a) Rewinding of electric motor of washing Calendaring machine/flat bed press etc. Using super enamelled copper winding wire Of gauge equal to or more than existing Vanishing the same after rewinding. (b) Cleaning washing ball bearing with kerosene Oil, greasing with new grease of make Castrol Refixing to its original position, testing and Commissiong complete all as specified.

M&L for repairing/servicing (rewinding) of three phase induction motor, Cap- 5HP, 415 Volts, Make- existing motor make and using Super enamelled copper winding wire of gauges equal to or more than existing. Including Replacement of sheet ‘E’ class insulation and sleeve Including the following jobs: (a) Reassembling the motor & refixing (b) Cleaning washing ball bearing with kerosene Oil, greasing with new grease of make Castrol Refixing to its original position testing and Commission complete all as specified and Directed

M&L for repairing/servicing (rewinding) of three phase induction motor, Cap- 2 HP, Make- existing motor make and using Super enamelled copper winding wire of gauges equal to or more than existing. Including Replacement of sheet ‘E’ class insulation and sleeve Including the following jobs:- (a) Reassembling the motor & refixing (b) Cleaning washing ball bearing with kerosene Oil, greasing with new grease of make Castrol Refixing to its original position testing and Commission complete all as specified and Directed

M&L for repairing/servicing (rewinding) of three phase induction /squirrel cage motor, Cap-10 HP 1400RPM 3 phase. using super enamelled copper winding wire of gauge equal to Or more than existing including Replacement of sheet ‘E’ class insulation and sleeve Including the following:- (a) Reassembling the motor & refixing. (b) Greasing of ball bearing with ball bearing after Cleaning of old grease with kerosene oil, reinstalling in the respective machine and testing/commission All as specified and directed.

M&L for repairing/servicing (rewinding) of three phase induction /squirrel cage motor, Cap-20 HP 1400RPM 3 phase. using super enamelled copper winding wire of gauge equal to Or more than existing including Replacement of sheet ‘E’ class insulation and sleeve Including the following:- (a) Reassembling the motor & refixing. (b) Greasing of ball bearing with ball bearing after Cleaning of old grease with kerosene oil, reinstalling in the respective machine and testing/commission All as specified and directed.

M&L for repairing/servicing (rewinding) of three phase induction /squirrel cage motor, Cap-25HP 1400RPM 3 phase. using super enamelled copper winding wire of gauge equal to Or more than existing including Replacement of sheet ‘E’ class insulation and sleeve Including the following: (a) Reassembling the motor & refixing. (b) Greasing of ball bearing with ball bearing after Cleaning of old grease with kerosene oil, reinstalling in the respective machine and testing/commission All as specified and directed.

Supply & fixing in repair/replacement of automatic hand iron cap- 18lbs, 1.2KW with sponged ironing including heating element, cord cord socket complete all as per specified and directed by Engr-in-Charge.

Dismantling of the equipments using adequate labour and for repairing, welding and replacement of defective wheels, nut and bolts suitable for Washroom Trolley, Dry Linen Trolley, Shelf Trolley and Mobile Table of Make FABCARE. Note:- Spare parts to be replaced shall be measured and paid under the following respective parts.

Supply and fixing in Repair/replacement Wheel Size 6" with brake, MAKE- ROLIN/SENSON/SATYAM

S &F in repair 63A four pole TPN, 10KA, 415Volt C curve type all as per specified &directed by Engr-in-Charge. Make- L&T/ HAVELLS/ LEGRAND

S &F in repair 25A four pole TPN, 10KA, 415Volt C curve type all as per specified &directed by Engr-in-Charge. Make- ABB/ HAVELLS/ LEGRAND

S &F in repair 63A MCCB 4 pole all as per specified & directed by Engr-in-Charge., Make- L&T/ HAVELLS/ LEGRAND

S & F in repair sheet metal enclosures 8 way SPN double door DB with fittings all as per specified and directed by Engr-in-Charge. Make- LEGRAND/HAVELLS/STANDARD

M & L for rewinding Air compressor three phase motor of capacity 4 kw/ 5 Hp , Make-ELGI equipments limited/ Bharat bijlee, 1435RPM speed by dismantling the electric supply, removing the burnt copper winding and rewinding the motor with appropriate gauge of super enamelled superior quality of copper wire, varnishing, heating, replacement of both ball bearing, reassembling the same and testing complete all as specified and directed by Engr-in-Charge.

M & L for overhauling of the compressor of capacity 5 HP, Max working pressure -12KG/CM2, HYD test pressure -(19.8 or 20)KG/CM2, AIR tank capacity-220 Ltr, Make- Kirloskar/ ELGI by disconnecting the compressor from motor, opening and replacing following worn out spare parts reassembling complete compressor & refixing in same position & connecting including control panel repair, replacing the rusted nuts, bolts, washers etc and testing complete all as specified and directed by Engr-in-Charge. (a) gear wheel- 02 Set (b) Distance ring-01 Nos (c) Injection rings -04 Nos (d) Piston rings - 16 Nos (e) Pressing bush- 04 Nos (f) O- ring -01 Nos (g) Oil Seal -01 Nos (h) Tensioning element- 02 Nos (i) Upper and lower rotor et- 02 Nos (j) Gasket packing- 02 Nos (k) Oil level sight glass - 02 Nos (l) Bearing set- 01 Set

M & L for repairing weighing machine including display plate with minor defects and minor spare parts, sensor etc complete all as per specified and directed by Engr-in- Charge.

Supply and fixing, in repair, installation, testing and commissioning complete set of out outdoor unit kit working on R-22/404a of 3 ton, company made consist of condenser coil, wiring kit, condenser fan motor, condenser fan or blower, contactor, terminal etc with compresser and making plateform for outdoor unit with suitable size of fastener and MS frame work and making good the disturb surface complete all as specified and directed. Make- Model no- RAUH02012KP-O of bluestar/ice make/Carrier. Note- (i) Old taking out dismanteled unit shall be deposited to MES store yard from existing location .The rate include necessary transportation & Manpower for dismantling and transporting the unit. (ii) Old and dismantled MS frame will be considered in sch of credit Srl No 87.

Supply and fixing, in repair, installation, testing and commissioning complete set of indoor unit kit working on R-22/404a of cap 3 ton, consist of blower motor, blower, wiring kit with cooling coil with housing with bracket frame etc, including making plateform for indoor unit with suitable size of fastener and MS frame work and making good the disturb surface, interlocking control wiring, timer, sub zero all as required complete all as specified and directed. Make- Model no- RAUH02012KP-I of bluestar/ice make/Carrier. Note- (i) Old dismanteled indoor unit shall be deposited to MES store yard from existing location. The rate include necessary transportation & Manpower to dismantling and transporting the unit. (ii) Old and dismantled MS frame will be considered in sch of credit Srl No 87.

S&F in repair sandwich type PUF panel having ceiling size 224"x166", panel thickness 60mm and PUF density 40+2 kg/m3, panel surfess material GI PP sheet with pvc film complete all as per requirement at site complete all as specified and directed. Make-Bluestar.

S&F in repair sandwich type PUF panel having ceiling size 209"x151", panel thickness 60mm and PUF density 40+2 kg/m3, panel surfess material GI PP sheet with pvc film complete all as per requirement at site complete all as specified and directed. Make-Bluestar.

S&F in repair copper tubing 5/8" dia & wall thickness-0.035 mm with required nitrile rubber insulation for connection of indoor and outdoor unit as per site requirement complete all as specified and derected. Make:- Totaline/Godrej or equivalent.

S&F in repair copper tubing 3/8" dia & wall thickness-0.032 mm with required nitrile rubber insulation for connection of indoor and outdoor unit as per site requirement complete all as specified and derected. Make:- Totaline/Godrej or equivalent.

S&F in repair timer Electronic type, starting time range 3-60 sec rated voltage :- 200-240V, 50HZ including connecting complete.

Supply and fix in repair Controller Suitable for Cold Chamber complete all as specified and directed. Make:- Item Code CBCL-B027-00 of Blue Star or Equivalent model of Carrier/ Ice Make.

M & L for shifting of outdoor units of cold chamber from inside to outside at suitable location with making plateform of PCC of 1:2:4 type B-1 using 20 mm Graded stone aggregate of suitable size for each outdoor unit with suitable size of fastener and MS frame work and making good the disturb surface and recharging the outdoor unit with R-22 Refrigerant complete all as specified and directed.

M&L for fabrication of stand from MS Frame work of suitable size for supporting the copper tubing from indoor unit to outdoor unit including cutting, Jointing, welding & necessary fabricationcl incl necessary protection to be adopted while carrying out the job all as specified and as directed by Engr-in-Charge.

Outsource services of Data Entry Operators (04 Nos) under GE (E/M) Base Hospital for following:- (i) Data Entry & Preparation of reports & returns (ii) Other official typing work (iii) Maintenance of office records (iv) Filing & linking of correspondences for case of reference. (v) Taking direction & Putting up drafts accordingly. (vi) Compilation & Collection of data. Note:- (a) All outsourcing pers to have biometric attendance in all contracts. (b) In case biometric machine is off rd, Contractor to repair/replace the same within 24 hrs, otherwise same will be marked "Absent". (c) The Data Entry Operator(s) must be qualified Graduates/ Ex-Serviceman and knowledge of Computer. (d) The contractor will install and maintain a Biometric Based Attendance Monitoring System (BBAMS) and enroll their employed staff in it. (e) Contractor shall be bond to implementation to minimum wages as per gov policy, EPF and ESIC payment and quoted rate shall deemed to include these factors. Contractors shall made payment to the staffs throught RTGS/ RTS in account of individual and submit the details of proof, EPF & ESIC of each staffs before asking of any payment (RAR or Final Bill). (f) Any absence of deployed personnel shall invite a compensation of Rs 1000/- per day per individual. Contractor is to provide alternate arrangement if personnel is absent continuously for 7 days. No payment shall be admissible to contractor, when personnel is absent on duty.

(i) The estimated cost of the work in respect of BOQ Sr iterm No 38 (as based on minimum wages rates issued vide central/state) is Rs 1245312. If the quoted amount is found less than the estimated cost of Sr item No 38 of BOQ and tender of lowest bidder is considered for acceptance, then the lowest bidder will have to deposit FDR in favour of Accepting officer for the difference in estimated cost and Accepted amount in respect of BOQ Sr item No 38 within 30 days from date of acceptance. In case the said FDR is not submitted within 30 days the amount in question shall be recovered from contractor’s first RAR/Final bill whichever is earlier. However the FDR/recovered amount shall be released to the contractor after satisfactory completion of work. Attention is further invited added that when the amount of said recovery mentioned herein above is less than the amount of performance security as indicated under Clasue 02 on page 04 of CA and Clause 12 on page 11 of CA, no FDR is required to be submitted for quoting less rate against BOQ Srl Item No 38. However if the amount of performance security is less than the FDR to be submitted for less quoting rate, the difference of performance security amount and FDR amount(for less quoting rates) shall be deposited by the lowest bidder (whose tender is accepted) in the form of FDR for difference amount over and above performance security within 30 days from the date of Acceptance.

SANJEEV ENTERPRISES

Flint India