Special repair of Govt. ITI at village Muana in Jind Distt

Amount

Dismantling brick work, tile masonry or tile lining and tile terracing in cement (HSR 8.5-b)

Dismantling concrete reinforced cement concrete with cleaning and straightening and cutting of bars if required (HSR 8.6-e)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantlled (HSR 8.18-a) (a) Doors

Windows

Scraping of cement plaster (HSR 8.32-c)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (Straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centring and shuttering, laid in position complete in all respects. [HSR. 10.86 + 10.95 (a)]

Providing and laying 80 mm thick ISI marked interlocking paver block conforming to IS 15658:2006/IRC: SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect. (HSR 10.159)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. (HSR 11.9)

Tile terracing with one layer of tiles, 22.86cmx11.43cmx 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1:3 and top surface to be left clean. (HSR 13.14)

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thickcement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Not : Tile shall be of premium quality (first quality) of reputed manufacturer like:- NITCO, KAJARIA, RAK shall be used as approved by Engineer-in-charge. (HSR 14.91). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA shall be used as approved by Engineer-in-charge. [HSR 14.92(b)]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12mm thick cement plaster 1:5 (HSR 15.6)

Painting two coat with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shad including rubbing down old paint. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

White washing two coats. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.47)

Distempering with washable oil bound distemper two coats on old distempered work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (a)]. 2nd Quality

Supplying and fixing glass panes with moulding of commercial hardwood such as hollock, champ, chikrassy and cheaplash etc. (non-coniferous timber other than teak conforming to I.S. specification no. 1003 kiln-seasoned) (C) 4mm thick ( glazing area above 55 sqdm, but upto 84 sq.dm of each pane) (HSR 17.36-c)

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock & Champ only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood nd including cost of iron hinges, screw, chock/cleats, stops nails etc. complete in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (b) 35 mm thick. [HSR 17.90 (b) - Note 1 under 17.18].

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., c(non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panelsof 12 mm thick, commercial veneered both side particle board or plywood of B.W.R. grade, hot pressed, including cost of iron hinges, screws, chock/cleats stops and nails etc. complete fixed in position(excluding the cost of any fittings, other than specified above but including labour for fixing the same position. [HSR 17.91 (b) (-) 17.18 - Note]. (b) 35 mm Thick.

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Steel reinforcement TMT bars FE-550/EQR/FE-500 D grade or more for RCC work, where no included in the complete rate or RCC including straightening, bending, binding wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22) Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps, wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Pressed steel sheet frames (chowkhats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (c) door and window frame of size 127mm x 50mm with 40mm wide double rebate. (HSR 18.34-c)

Providing and fixing in position best Indian make Indian type orissa or orya water closet suite for sinking into floor, with raised foot treads complete with complete with 100mm H.C.I. 'P' trap with or without vent as required and all other necessary fitings as fully described in item no. 30.1 above. (a) size 580mm (i) White (HSR 30.2 a-i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON-CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary Fittings as fully described in item no. 30.3 above. (HSR 30.4-i) white

Providing and fixing in position 15mm i/d CP brass bib cock of best quality (as required by the Engineer–in–Charge) (a) Bib cock long body.(HSR 30.75-a)

Providing and fixing in position CP brass stop cock of best quality (as required by the Engineer–in–Charge) (a) 15mm stop cock (i) Stop cock male and female end (HSR 30.76 a-i)

Providing and fixing HDPE water storage tanks of sintex, Diplast. O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of building including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-charge (except civil work) (HSR 30.119) 1000 ltr. capacity

Recovery items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Brick Tiles @ Rs. 4.50/- Each

Doors @ Rs. 300/- Each

Windows @ Rs. 450/- Each

Brick Ballast @ Rs. 450/- Cum

THE K GROUP COOP LANDC SOCIETY LTD NARWANA