Addition Alteration of 54 Nos Type II Qtr at Bn HQ at Jwalamukhi of 22 Assam Rifles

Amount

SCHEDULE `A' (Addition/Alteration of 54 Nos Type-II Qtr at Bn HQ at Jwalamukhi of 22 Assam Rifles)

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade Old work (two coats)

Finishing walls with Acrylic Smooth eFinishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand)

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane, 3 mm thick

Providing and fixing 25 mm thick shutters for cupboard etc. :Panelled or panelled & glazed shutters Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading

25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per anufacturer’s specification and direction of Engineer-in-charge to take up necessary hardwareand fixtures. Stickers indicating the locations of hardware will be pasted at ppropriate places

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Dismantling of flushing cistern of all types (C.I./PVC/ Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White each

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 510x610 mm bowl depth 200 mm

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter

RE-WIRING M/L for point wiring in PVC conduit for light point/fan point/exhaust fan point/calling bell point with 1.5 Sqmm FR PVC insulated copper conductor in surface/recessed PVC conduit with piano type switch,phenolic laminated sheet suitable size MS box and earthingthe point with 1.5 Sqmm PR PVC insulated copper conductor single core cable as required.

M/L following piano type switch/socket on the existing switch box/ cover incl coonection etc, as reqd 3 pin 5/6 amp socket out let

M/L following piano type switch/socket on the existing switch box/ cover incl coonection etc, as reqd 6 pin 15/16 amp socket out let

M/L following piano type switch/socket on the existing switch box/ cover incl coonection etc, as reqd 5/6 amp switch

Wiring for light /power plug with 2x4 sq mm FR PVC insulated copper conductor single core cable in surface /recessed steel coduit along with 1 No 4 sq mm FR PVC insulated copper conductor single core cable for loop earthing as reqd.

Supply and fixing metal box of 150mm x 75mm x 60mm deep on surface or in recess with suitable size of phynolic laminated sheet cover in front including providing and fixing 05 pin socket outlet 05 Amp and piano type switch 05 Amp,connection, painting etc as required

M/L for Sub main wiring in PVC conduit along with 2x2.5 Sqmm + 1x 2.5 sqmm earth of PVC copper conductor single core cable in surface/ recess PVC conduit as required. power plug point wirth 2x4 Sqmm FR PVC insulated copper condudtor single core cable in surface/recessed PVC conduit alongwith 01 no 4 sqmm FR PVC insulated copper conductor single core cable as required.

M/L for 2+4 way single pole and netural,sheet MCB distribution board 240 volt on recess/surface complete with tinned copper busbar,netural busbar,earth bar ,dectable glannd plate,inter connection incl earthing as required ( But without MCB /RCCB/ Isolator)

M/L for 5 amp to 32 amp SPN rating 240 volt 'C' series MCB suitable for lightning and other load of poles.

M/L for MCB 5 to 32 amp SP rating 240 volt 'B' series MCB suitable for lightning and other load of poles.

Installation,testing and commissioning of ceiling fan, incl the wiring the down rods of standered length (upto 30 cm) with 1.5 sqmm FR PVC insulated, coppere conductor, single core cable, incl P/F phenolic laminated sheet cover on the fan box etc as required.

Installation,testing and commissioning of pre-wired, fluorescent fitting /compact fluorescent fitting of all types, with all accessorioes and tube etc.directly on ceiling/wall, incl connection with 1.5 sqmm FR PVC insulated, copper conductor, single core cable and earthing etc as required.

Victor and Company

M/s K B Enterprises