PROVN OF TOILET BLOCK FOR OR LINE COMMA PROVN OF COVERED DRAINAGE SYSTEM AND PROVN OF FALSE CEILING IN BLDG NO T 23 AT HQCC CAMP UNDER GE WEST LUCKNOW

Amount

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material soils n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Removing surplus excavated material soils exc. 250m but n.exc. 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Labour only for Earth (soil) filling under floors or in foundatoins including spreading, levelling in layers n. exc 25cm thick, watering and well ramming complete all as specified and directed. NOTE: Soil obtained from excavation shall be used.

M&L ATT for treating the bottom and sides of excavation @ 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L ATT for treating the backfill in contact with foundation @ 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed.

M&L ATT for treating the top surface of filled earth @ 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L ATT for treating the soil under plinth protection @ 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basements slabs, under reamed piles and mass concrete and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in slab supported on wall, beams and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and similar works complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished surface complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splay between floors and beams, etc. and similar works for rough finished surfaces complete all as specified and directed

S&F pressed steel door frame of size 105x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood rail and style type plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial venneering on both faces, the size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for Top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L for 4mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F steel ventilators with top hung shutters including box type hinges or factory made butt hinges with steel handle and steel peg stays etc. complete all as specified and directed.

S&F false ceiling with 4mm thick 'E' Board (Make: Everest) of size 600x600mm, white, prelaminated sheet embossed reinforced designer ceiling board tiles of approved texture and powder coated, hot dipped GI imposed grid frame work complete all as specified and directed including all necessary drilling, cutting to fix electrical items as under with the following:- (a) 24x24x0.45mm thick powder coated GI angle plugged @ 600mm c/c along perimeter of wall. (b) 24x32x0.33mm thick powder coated GI tee as main and cross runners suspended with 4mm dia GI wire suspenders with adjustable clamps and dash free fastners with rawl plug and screws plugging in RCC slab etc. placed @ 600mm c/c from perimeter of wall. (c) Fixing of 4mm thick 'E' board tiles and finished complete with one coat of oil emulsion distemper on ceiling. NOTE: The complete ceiling work shall be executed as per manufacturer's instructions and as directed.

M&L structural steel work with rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc and similar articles conforming to Fe-410W (Gde E-250) quality-A complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surface of ceiling and finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described and treating small articles such as stop, covers, gully gratings, holdfasts, end of posts, back of chowkhats, etc. area n. exc. 0.1sqm each and treated with tar or coal tar black paint complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in floor finished even and fair without using extra cement as in levelling course complete all as specified and directed.

M&L for joint free glazed ceramic tiles, coloured, superior quality of size 350x250x7mm/ 450x350x7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick screed bed in cement mortar 1:4, including rubbing, rubbing, grinding, making hole for gas pipe line and including making sandwitch moulding to edges complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves etc and similar works set in cement mortar 1:4 complete all as specified and directed.

M&L 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc. finished even and fair without using extra cement complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 1000 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified and directed.

S&F 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated or aluminium hinging device ISI marked as approved complete all as specified and directed.

S&F Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F counter top vitreous china wash basin, coloured, oval shape, approx size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F vitreous china urinal, half stall type, white, with grating and union for discharge pipe (excluding flushing cistern and flush pipe), including waste pipe, providing and fixing plugs, bedding urinal against wall etc. complete all as specified and directed.

S&F push type flush valve 15mm bore, fancy type, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories for half stall type urinal complete all as specified and directed.

S&F bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F central hole basin mixer, fancy type, brass chromium plated, with round spout with popup waste system, including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed.

S&F wall mixer with telephonic shower arrangement, connecting legs and wall flanges, fancy type, brass chromium plated, with costed swinging spout including plugging and securing to walls suitable for 15mm bore pipe complete all as specified and directed.

S&F brass chromium plated overhead shower rose with arms, 125mm size, round shape, single flow, fancy type, suitable for 15mm bore pipe and fixed complete all as specified and directed.

S&F hand shower (health faucet), superior quality, round shape, single flow, brass chromium plated, with 1m long chrom finish flexible pipe with wall hook bracket etc. and all fittings for EWC complete all as specified and directed.

S&F CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F 5.5mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F 5.5mm thick sheet glass corner shelf assembly, fancy type, sheet glass shelf of size 250x250mm, with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F PVC bath cabinet/ mirror cabinet (multi utility) with 4mm thick looking mirror of overall size 560x410mm complete all as specified and directed. Make: Commander/ Polytuff/ Prayag

S&F peg set of 6, brass chromium plated, fancy type, with 40mm wide brass CP strip, fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y), equal or unequal suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y), equal or unequal suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with gratings including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

S&F PVC (SWR) vent cowls suitable for 110mm bore pipes complete all as specified and directed.

S&F PVC (SWR) vent cowls suitable for 75mm bore pipes complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for 150mm bore salt glazed stoneware drain pipes, complete with collars, laid in trenches and jointed in cement mortar 1:1 as in drains complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete foundation bed to 150mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L cutting into existing manholes for connecting new drains, making good to 150mm bore pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

M&L for provn of roof treatment with polymeric water proofing membrane all as given below:- (a) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (b) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (c) M&L for applying two coats of aluminium paint on membrane @ 0.10 Kg/Sqm (each coat) complete all as specified and directed.

M&L for construction of Septic Tank suitable for 150 users with RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in bases, baffle walls, beams, roof slab, cover slab, covers etc., brick work with old size fly ash bricks in CM 1:4 and manhole cover made out of 6mm thick MS steel sheet and frame of angle iron 50x50x6mm including all required earthwork in soft/loose soil, cement concrete etc. complete all as shown on CELZ drawing No. TD/217 sheet 1/2 & 2/2 amended upto date complete all as specified and directed.

M&L construction of Soakage Well of size 3.00m dia, 6.00m effective depth and 7.50m overall depth with fly ash bricks and RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in cover slab etc. including all required earthwork in soft/loose soil, filling of brick bats and cement concrete etc. complete all as shown on CELZ drawing No. TD/576 sheet 1/2 & 2/2 dated 16.06.1989 complete all as specified and directed.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 96 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 96 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item no 96 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, tripple pole and neutral 4 way, 415Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 8 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, tripple pole & neutral 63 Amp, 415 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F sheet metal enclosures, single pole with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F wall mounted 18/20 W LED integrated tube light fitting, 1200mm long batten with extruded aluminium housing, frosted diffuser and integrated electronic driver with decorative end cap complete and one no 18/20 W LED 6000K, 230V, tube light complete with all required fittings and fixtures arrangement including and provn of connection from ceiling rose to luminaries with PVC 3 core flexible copper wire complete all as specified and directed. Make: Havells cat no. LUMILINE PLUS BS 20WLED865SPCSS or Surya Visco cat no. SLEBT 20 IL or C&S Nakshtra series cat no. LTTB4F20WLED/WI or Philips cat no. 021LED 22S6500/4000 PSU GR/SI.

S&F wall mounted 9/10 W LED integrated mirror light fitting, 600mm long batten with extruded aluminium housing & integrated electronic driver and one no. 9/10 W LED, 6000 K, 230V tube light including and provn of connection from ceiling rose to luminaries with suitable size three core flexible copper wire complete all as specified and directed. Make: Havells cat no. LUMILINE PLUS BS 10WLED865SPCSS or Surya Visco cat no. SLE BT 10 or C&S cat no. LTDC01210WLED/WD or Philips cat no. BN 021LED 12S6500/4000 PSU GR/SI.

S&F security light fitting of 25 W LED 6000 K, with high power LED source (more than 100 lumens/ watt), PDC housing, IP65 with 4KV inbuilt surge protection driver and one no. 25W LED tube, with all accessories, prewired with and fixed to bldg/pole including GI bracket 1.20m long bent to shape, made out of 40mm dia GI light grade pipe with nuts, bolts and washers and provn of connection from ceiling rose to luminaries with PVC 3 core flexible copper wire complete all as specified and directed. Make: Havells cat no. Endura Peral SL25WLED757SSYTOPCMP or Surya cat no. LEXON SLE UL 25W IP66 or C&S (Indus E series) cat no. LTESS25WLED/L5 or Philips cat no. BRP042LED25CWR1S1PSU GR.

M&L Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m deep below normal ground level, connected to galvanised earth lead wire 4.0mm dia (7.50m) by means of bolts, nuts, check nuts & washers of galvanised iron or steel, earth lead wire protected by 15mm dia GI pipe light grade, 20mm dia light grade GI pipe for watering, meshed funnel, alternate layer of charcoal and common salt complete all as SSR Item No. 19471 and shown in electrical plate No. 3 of SSR part-I with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way in lieu of CI pit cover and protection including necessary excavation and earth work complete all as specified and directed.

S&F heavy duty metal body exhaust fan 300mm sweep, copper wound, 1400 RPM, AC single phase, 230/240 volts, fancy type complete with fan motor, blade, bracket, ring and louvers including and provn of grouting 4 nos anchor bolts with nut and washer and making good to disturbed surfaces to match the existing and provn of connection with with three core flexible copper wire cable of size 1.50sqmm from ceiling rose to fan complete all as specified and directed. Make: Orient (Heavy duty)/ Usha (Turbo heavy duty metal body)/ Havells (Turbo Force HP)/ Khaitan (heavy duty metal body).

M/S KAUSHIK CONSTRUCTION

Matrubhoomi Construction

suniltraders

M/S Chandra Mohan and Sons