ADDN / ALTN TO TOILETS OF MTTI HQ BLDGS AND PARKING SHED OF MTTI HQ BLDG P-48 AT AF STN UNDER GE AVADI

Amount

Taking down plastering on lathing (other than wire-netting), without removing lathing, in cement or cement-lime mortar (one side only measured in cases where both sides are plastered) etc complete all as directed

M&L for rendering 10mm thick on wall/vertical surfaces of brick work/concrete work in CM 1:6, surfaces finished even and smooth without using extra cement all as specified

M&L for preparing new plastered surfaces of wall and applying two coats of Oil bound Distemper over a coat of alkali resistant primer over 3 mm thick wall care putty to internal surfaces of wall complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises. complete all as specified and directed.

M&L for Non skid light coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular ) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc . set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles, laid over 20 mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L for Glazed light coloured ceramic tiles in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile over and including 10mm thick rendering in CM 1:4 etc. all as specified and directed

M & L non skid ceramic light coloured tiles 7-8mm thick area of each tile exc 0.06 Sqm but n.exc 0 .11 Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match the tile over and including 15mm thick screed bed in CM 1:6.

S&F in repair vitreous china squatting pan "Orissa" pattern size 580 mm x 440 mm white with integral foot rests including 10ltrs capacity PVC flushing cistern (low level with inlet, ball valve float), brackets, flush pipe of polyethylene of low density PVC 32mm dia for low level cistern all as specified and directed

S&F in repairs Vitreous China urinals, half stall type with PVC waste/ flush pipes, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, grating and Union for discharge pipe etc complete all as specified and directed

S&F in repair tubular towel rail alumunium anodised , 20mm dia, D type 60 cm long between flanges all as specified and directed

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, all as specified and directed.

S&F in repairs 15 mm dia Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for PVC/ iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs 15mm dia stop valve/Angle valve, chromium plated fancy type cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for PVC/iron pipes or for unions and fixed of,complete all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 600 mm.

Taking down chowkhats or frames with shuttters (without taking off shutters from frames) n.exc 1.5 sqm each all as specified and directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm thick MS square tube of 19 gauge mitre cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mmx15mm MS square tube inside the 19mm MS square tube and suitably screwed complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (styles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on front face and 2mm plain colour PVC sheet on backface, supplying and fixing in frame at site as per specification complete all as specified and as directed.

S&F 75mm size type C21 Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised complete all as specified and directed.

S&F aluminium handle 100 mm cast type anodized all as specified and directed

S & F aluminium anodized tower bolt 100mm size complete all as specified and directed.

M&L for preparation of old wall surfaces including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash including cleaning the floor/joinery surfaces, glass panes all as directed.

All as per item No. 22 here - in -before but one coat of white wash on ceiling

M&L for dismanteling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed

M&L for Dismantling wrought iron or mild steel work of any description not otherwise provided including for truss etc complete all as specified and directed

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete conforming to FE 410 Grade E 250 quality A ect all as specified and directed

M&L for half round or other steel section embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary and similar work conforming to Fe-290 Gde E-165 etc all as specified and directed

Demolition of cement concrete of any description (unreinforced) in ground floors and pavings n exc 15 cm and 30 cm thickness (below or above ground level) etc complete all as specified and directed

Excavation in post holes or (Similar holes) each n.exc 0.5cum, getting out, ramming the excavated surfaces watering and removing surplus soil to a distance n.exc 50m and making good surfaces in hard/dense soil.

M&L for PCC 1:3:6 type C2 (40mm graded Stone aggregate) as in foundation of post holes filling and mass concrete all as specified and directed.

M&L for Brick work with flyash old size bricks straight or curved on plan exc. 6m mean radius etc. built in CM 1:6 complete all as specified and as directed

M & L 10 mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:6) finished even and smooth (without using extra cement).

M&L for preparation of newly plastered wall surfaces including and applying three coats of white wash complete all as directed.

M&L for preparing new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed

M&L for broken stone Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for 100mm thick plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate in sub base or mass concrete complete all as specified and directed.

M & L for 50mm thick plain cement concrete 1:2:4 type B-1 (Using 20 mm graded stone agg) as in floors surface finished even fair complete all as specified and directed.

M&L for Forming contruction joint 30mm deep x 10mm wide and filled with sealing compound, Grade ‘B’ complete all as specified and directed.

.Removal excavated surplus soil to a distance n.exc. 50 m and depositing where directed at level n.exc. 1.5 m above the starting point all as directed by Engr-in-Charge.

Taking down copper/aluminium point wiring for (light, fan, socket or power) complete including unserviceable fittings such as switches, ceiling rose, holders, sockets etc. and making good the disturbed surfaces on wall/floor etc complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm (nominal area) PVC insulated,FRLSH unsheathed, multistrand, 1100 volts grade copper conductor cable single core, drawn through with and including non metallic PVC conduit 25mm dia and its accessories fixed on wall/ ceiling/ trusses /steel structure with suitable clamps , screws etc including one run of 1.5 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.6 mm thick MS terminal box finished to wall/steel structure with 3 mm thick laminated hylam sheet top cover all as specified for :-

One light point controlled by one switch.

One exhaust fan point controlled by one switch.

One 3 pin 5 amps socket point on same board

One switch socket outlet 3 pin 5 Amps on independent board.

S&F ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified.

S&F switch piano, flush type single pole, one way 5 Amps complete all as specified.

S&F switch socket 3 pin 5 amps , multi pin , flush type,complete all as specified.

S&F Lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete with LED lamp 12W capacity complete all as specified and as directed.

S&F LED batten fitting 20/22 W, 230 V, extruded aluminium housing provided for easy heat dissipation wall mounted complete pre wired and including tube and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting complete all as specified and as directed.

S&F Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

S&F MCB DB SPN 4 way, double door, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCB double pole as incomer and SP MCBs as outgoing with tinned copper bus bar, neutral link, earth link and connecting up complete all as specified and as directed. Note : Incoming and Outgoing MCB measured separately relevent items.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of double poles and current carrying capacity SPN 40 to 63 AMP in the MCB DB complete with connection testing and commissioning complete all as specified.

Exhaust fan, heavy duty, 300mm sweep, 1370 RPM, with louvers, metal body conforming to IS-2312-1967, AC single phase, 240 Volts, 50 Hz and connecting including provision of two way PVC connectors, 1 sqmm flexible three core multistranded copper conductor cable from ceiling rose or connector to fan including earthing and fixing arrangements like making hole in wall and finishing to shape to match adjoining surface and writing MES No.20mm height with synthetic enamel paint black complete all as specified and as directed.

BESPOKE ENGINEERING

M/s Omm Muruga Enterprises