SPECIAL REPAIRS TO BLDG NO. T-695 AND P-40 AT ALGARAH UNDER GE 867 EWS

Amount

S&F pre-painted galvalume aluminium zinc coating GI based corrugated (Trepezium or tiled pattern etc.,) steel sheet 0.50 mm thick (with 0.45 mm BMT) of any colour having tensile strength of 550 Mpa (pitch of corrugation shall be 200mm to 250mm and crest shall be 28mm to 32mm) as in roof covering/ cladding to wall fixed with self tapping screws including taking down existing steel sheeting of any type complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick (with 0.45 mm BMT) of any colour having tensile strength of 550 Mpa as in roof covering, eaves board, ridges, hips,valley gutters, drip and straight flashing cladding to wall etc, fixed with self tapping screws including taking down existing steel sheeting of any type complete all as specified and directed by Engineer-in-Charge. Make for Item No. 1&2: TATA BLUESLOPPE/ LLYODS /JMBS/ EVEREST INDUSTRIES LTD/CRIL/JSW STEEL or equivalent as approved by GE.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

S&F Fe 410-W (Gde-E- 250) quality-A Rolled steel sections, roof trusses, framed trussed, purlins, crane gantries, rails and fastening and heavy brackets framing (Beam, tee, angle channel or flat section) incl distance pieces, cleats, nut and bolts complete all as specified and directed by Engineer-in-charge.

Supply, fabrication, and errection of required height (900 to 1100) mm high SS hand railing system intergrated with SS304 grage 38mm Dia & 1.6mm thick vertivals, top Rail SS grade 304 dia 50mm Dia 1.6mm thick through SS and two MID Rail of 25mm Dia & 1.6 mm thick connected to Baluster through weilding Baluster fixed to slab with GI Baseplate & M12x200 mm with 10x100mm Fastener. A SS cover plate would be provided above GI base plate with our all tools and tackles complete all as specified and directed by Engineer-in-charge.

M&L Preparing old or previously treated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L Preparing new or previously un treated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer all as specified and directed. Make for Item No. 6&7: ASIAN/ SHALIMAR/ BERGER/JENSON&NICHOLSON/IEL

M&L for second class hard wood clean sawn scantling, unframed and fixed including taking down existing scantling complete all as specified and as directed by Engineer-in-Charge. WOOD: Sal/Kalasiris/Chaplash/Hollock/Bijasal

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of creosote oil complete all as specified and directed by Engineer-in-Charge.

S&F GI frame work of size 605 x 605 mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 6mm dia GI hangers (upto1200mm length) adjusting level and providing 4 mm thick E Board (Everest) noncombustible moisture resistant plain building boards, fixed to GI frame work with screws as in ceiling and applying 3 coats of white wash including taking down existing ceiling boards of any type complete all as specified and as directed by Engineer-in-charge. MAKE: Bison/NCL/EVEREST/UPAL or eqivalent as approved by GE.

M&L for false ceiling with light weight PVC hollow section panels made of 1mm thick PVC sheet and overall thickness of panel minimum 7mm and 200mm wide strips fixed in and including GI frame work of size 605 x 605 mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including taking down existing ceiling boards of any type complete all as specified and as directed by Engineer-in-charge. MAKE: Rajshree plast wood/Sintex/Nandi or equivalent as approved by GE.

S&F Softwood 2nd class Wall Lining consisting of 15mm thick Clean sawn with butt joints Boarding, supplied & fixed with nails in any situation including taking down existing wall lining of any type complete all as specified and as directed by Engineer-in-charge.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and as directed by Engineer-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.5 Sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and as directed.

S&F second class hardwood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid ,rounded or chamfered put together with glue pinned joints all as specified and directed. TIMBER: - Sal/Kalasiris/Chaplash/Hollock/Bijasal

S&F 30mm thick factory made flush shutters, solid core construction with block board core and plywood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-Charge. Make: - Green Ply/Archid Ply or equivalent as approved by GE.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed. Make for Item No. 18 to 20: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE

S&F in repairs harrison rails (curtain rods or drapery rods) aluminium powder coated 18-19mm dia with fixing brackets, stops, rollers etc., complete all as directed by Engineer-in-Charge.

M&L Preparing new or previously un treated surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/JENSON&NICHOLSON/IEL

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 including dismantling existing tiles and removing rubbish off the premises complete all as directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm,on vertical surfaces such as skirting, dados, raisers to steps etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick screed bed in cement mortar 1:4 including dismantling existing tiles and removing rubbish off the premises complete all as directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 including dismantling existing tiles and removing rubbish off the premises complete all as directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm,on vertical surfaces such as skirting, dados, raisers to steps etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick screed bed in cement mortar 1:4 including dismantling existing tiles and removing rubbish off the premises complete all as directed by Engr-in-charge.

M&L for 10mm thick vetrified ceramic tiles of light shade (square/rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for 10mm thick vetrified ceramic tiles of light shade (square/rectangular) polished area of each tile not exceeding 0.36 sqm, in skirting etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for coloured glazed ceramic tiles of size 350x250,450x350 mm and 7mm thick on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 backing coat including dismantling existing tiles and removing rubbish off the premises complete all as directed by Engineer –in-Charge. Make for Item No 23 to 29: NITCO/ SOMANY/ ASIAN / JOHNSON/KAJARIA/ORIENT BELL

M&L for 75 mm thick Plain Cement Concrete 1:3:6, type C2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as specified and directed by Engineer-in-charge.

M&L for cement concrete polished coloured chequered tiles 300 x300x 25 mm thick with grey cement and pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors over and including 20 mm thick screed bed in cement mortar 1:6 including demolition of existing stone slabs and tiles of any description or thickness including concrete bedding and removing rubbish off the premises complete all as specified and directed. Make: NITCO/ULTRA/EUROCON/DECO/BHARAT or equivalent as approved by GE.

S&F Powder coated aluminium frame for partitions, doors, windows ventilators with one or more rebates, grills including joining cleat for fixing etc., complete all as specified and dierected by Engr-in-Charge.

S&F powder coated aluminium window and ventilator glazed shutters sliding type without sash bars, with standard aluminium sections for shutter top & sides, shutter bottom, shutter interlock of weight 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber packing, rollers, locking plates, screws, etc., as per manufacturer's instructions complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber/neoprene packing, handles 2 No's in each door, hinges,etc., as per manufacturer's instructions complete all as specified and directed. Make for Item No. 32 to 34: JINDAL/INDALCO/HINDALCO

S & F 5.5 mm thick sheet glass ordinary quality and fixed in aluminium fames area exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge. Make:- TRIVENI/ SAINT GOBAIN/ MODIGUARD/ATUL/ HINDUSTAN or equivalent as approved by GE.

S&F Brass Mortice lock, vertical type, size 100 mm, 4 levers complete all as specified and directed. Make:- GODREJ/LINC or equivalent as approved by GE.

S&F factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification and dawings.

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing. Make for Item No. 37 & 38: - SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, all as specified and directed.

S&F 100 mm size butt hinges, ectruded aluminium alloy with galvanised mild steel hinhe pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 125 mm long Aluminium alloy handles cast type anodised all as specified and directed. Make for Item No. 39 to 42: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE

S&F in repairs PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

M&L for plain cement concrete bed 1:4:8, type D2 (using 40 mm graded stone aggregate) to drain pipe 100/110 mm bore including packing under and hunching against the sides of pipes after they laid and tested complete all as directed by Engineer - in -Charge.

S&F PVC (SWR) pipes 110mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors or trenches including taking down existing pipes complete all as directed by Engr-in-Charge.

S&F PVC (SWR) pipes 75mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors or in trenches including taking down existing pipes complete all as directed by Engr-in-Charge.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed by Engr-in-Charge. Make for item No 45 to 47: PRINCE/ SUDHAKAR/ NANDI/ FINOLEX/ SWASTIK/SUPRIME

S&F 15mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete including short lengths including taking down existing GI pipe all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

S&F 20mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete including short lengths including taking down existing GI pipe all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

S&F in repairs Coupled (WC and flushing cistern) water closet (One Piece) white including connection to trap and flushing pipe anti syphonic pipe etc., complete all as specified and as directed by Engineer-in-charge. Make: JAQUAR/HINDWARE / NEYCER/ PARRYWARE / CERA

S & F in repairs vitreous china, pestal colour wash hand basin with pedestal , flat back size 670x510mm including MS brackets including cutting and priming in with PVC waste pipe 32mm dia of suitable length and waste fittings 32mm bore brass chromium plated complete all as specified and as directed by Engineer-in-charge. Make: JAQUAR/HINDWARE / NEYCER/ PARRYWARE / CERA

S&F in repairs brass chromium plated tubular towel bar of 20mm dia D' type 60cm long between flanges complete all as specified and as directed by Engineer-in-charge. Make: JAQUAR/SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F in repairs 15 mm Central hole mixer , cast copper alloy , with capstan heads, chromium plated, screwed down high pressure , with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. Make: JAQUAR/SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F bib taps 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, screwed for iron pipe all as specified and directed by Engr-in-Charge. Make: JAQUAR/SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F Stop/angle valves 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, concealed type with long shank ang cup screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-Charge. Make: JAQUAR/SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F CP wall mixer fancy type 3 in one system with provision for both telephone shower and overhead shower complete with bend pipe 15mm including taking down existing old unserviceable mixer complete all as specified and directed by Engineer-in-Charge. MAKE: HINDWARE Cat No. F110019 or equivalent in JAQUAR/ESSCO (DELUX)

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) exceeding 10cm width and setting in cement mortar 1:6 including demolition of existing brick masonry complete all as specified and directed by Engineer-in-charge. Make : Shankar Saw Mills/Sangam Prefeb Products or equivalent make as approved by GE.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement including taking down cement plaster on brick or stone masonry surfaces of walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including waterproofing compound @ 3% by weight of cement as per manufacturer's instructions including taking down cement plaster on brick or stone masonry surfaces of walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including waterproofing compound @ 3% by weight of cement as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.

M&L preparing new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of primer over thin layer of wall care putty (Birla white/Berger/Asian) complete all as specified and as directed by Engineer-in-Charge. Make: ASIAN/SHALIMAR/BERGER/ JENSON & NICHOLSON/IEL

M&L preparing old distemperd surfaces of walls and applying one coat of distemper oil emulsion complete all as specified and as directed by Engineer-in-Charge. Make: ASIAN/SHALIMAR/BERGER/ JENSON & NICHOLSON/IEL

M&L for complete removal of existing treatment from surfaces of walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces on external walls complete all as specified and directed by Engineer-in-Charge. Make: APEX of ASIAN or equivalent in JENSON & NICHOLSON/ BERGER/ SHALIMAR

M&L for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC conduit, medium grade of suitable size with all necessary fittings, concealed in walls/ceilings etc., including 1.5 Sq mm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and including modular type terminal boxes with inner and outer cover concealed type for mounting fittings like modular switch, socket, fan regulator etc., for one light /fan point controlled by one switch/one bell / buzzer point controlled by one bell push/one 3 / 5 -pin switch socket outlet 5 amps on independent board including testing on completion including taking down existing unserviceable point wiring including switches, sockets, regulators, ceiling roses, terminal boxes and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

All as per item No. 66 above but for One 3/5 pin switch socket outlet 5 amps on same board along with other switches complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with 2.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC conduit, medium grade of suitable size with all necessary fittings, concealed in walls/ceilings etc., including 2.5 Sqmm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and including modular type terminal boxes with inner and outer cover concealed type for mounting fittings like modular switch, socket, fan regulator etc., for one 5 / 6 -pin switch socket outlet 15 amps on independent board including testing on completion including taking down existing unserviceable point wiring including switches, sockets, regulators, ceiling roses, terminal boxes and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge. Make for Item No. 66 to 68 Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Conduit: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

M&L for sub main wiring complete with 2 runs of 4 Sqmm PVC insulated heavy duty and unsheathed FRLS cable with multistranded copper conductor and drawing through and including non metalic rigid PVC casing & caping of 25mm size fixed on wall/ceiling and connecting terminal ends including provision of 1 run of 4 Sqmm PVC insulated heavy duty and unsheathed FRLS cable with multistranded copper conductor as earth continuity conductor and connecting to earth dolly including taking down existing sub main wiring complete all as directed by Engr-in-charge. Note: 2 runs of 4 Sqmm and one run of 4 Sqmm and one run of Casing&Caping shall be measured as one unit length. Make Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Casing&Caping: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

Supply and fixing modular switch one way 6 Amps, 1 module complete all as directed by Engr-in-charge.

Supply and fixing modular switch one way 16 Amps, 1 module complete all as directed by Engr-in-charge.

Supply & fixing modular socket, 6A-2/3 pin combined 2 module complete all as directed by Engr-in-charge.

Supply and fixing modular socket 6/16A, 6 pin, 2 module complete all as directed by Engr-in-charge. Make for Item No 70 to 73: - MK/ANCHOR ROMA/CRABTREE/ NORTH WEST/LEGRAND/HAVELLS

S&F lamp holder, PVC/Polycarbonate insulated body with back plate for batten fittings complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose 3 terminal PVC/Polycarnonate, isolated body complete all as specified and as directed by Engineer-in-Charge. Make for Item No. 74&75: (i) Anchor (ii) Plaza, (iii) Havells (Crabtree) (iv) ABB (v) Shalabh

S&F Energy efficient LED Tube light fitting, 4', 1x18 watt, with LED tube rod 18 Watt, CCT- 6000K/3000K with bipin holders, connector block etc., complete with all accessories internally prewired and including connecting up with three core pvc sheathed flexible copper conductor cable of size 0.5 sqmm and 2 Nos PVC mounting blocks including taking down existing fitting complete all as specified and as directed by Engineer-in-Charge. Make: Philips Model Batten TMC 501, TMC 501P 1xT-LED 22 W P3241 Tube rod MAS LED tube 18W 1800 lm 865 T8 or equivalent in Crompton/Havells.

S&F 2' surface/wall mounted LED batten 10 watt, CCT - 5700K/3000K, system lumen output not less than 950lm, extruded aluminium housing with high quality Polycabonate diffuser, Operating temperature: -10° C to +45° C, Operating voltage range: 140-270 V, Average LED life L70B50: 50000 hours, CRI ≥ 80, system efficacy ≥95, including necessary screwing/fixing etc and connecting up with ceiling rose including taking down existing fitting and making good disturbed surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Crompton Cat part No "LDL-10-CDL" or equivalent in Philips/Havells.

S&F Endura LED Bulkhead fitting including 10 watt LED bulb, CCT - 5700K/3000K, IP-66/IK-09 system lumen output not less than 950lm, extruded aluminium housing with high quality Polycabonate diffuser, Operating temperature: -10° C to +45° C, Operating voltage range: 140-270 V, Average LED life L70B50: 50000 hours, CRI ≥ 80, system efficacy ≥95, including connecting up with 3.0 core, 0.5 sqmm copper conductor PVC sheathed from connector to ceiling rose including taking down existing fitting and making good disturbed surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Crompton Cat part No "LBHP-10-CDL" or equivalent in Philips/Havells.

Supply and fixing surface/recess mounting LED round shape 06 Watt, Slim design, Polycarbonate housing with superior light output and integral driver, Efficacy 100 lm/W, lumen output 600lm, low glare to prevent eye strain, surge protection of 2 KV with wide voltage 160-360V, BIS Certified, CCT 6000K/3000K, cool day light complete with all accessories duly pre-wired and including lamps and connecting up with three core PVC sheathed flexible copper conductor cable of size 1 sqmm including taking down existing fitting and making good disturbed surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Philips Model - Green LED surface or equivalent in Crompton,/Havells/Bajaj/Wipro.

Supply and fixing in repair of 36 watt LED edge lit luminare of 600 mm x 600 mm, CCRT 6000LK/5700/3000K and suItable for armstrong/grid ceiling complete including electronic driver including taking down existing fitting and making good disturbed surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Havells cat part No.VENUSNEOHE2X2PLR18-42WLED830MOD for Panel, LEDDRIVER36V36WS for 36 Watt LED driver or equivalent model of CG/Philips as approved by GE.

S&F sheet metal enclosure DB SPN 8 way 240 V with 200 Amp rated bus bar, powder coated, double door including taking down existing DB with MCBs complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing of MCB SPN 40 Amps, 10 KA breaking capacity, 240 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing of MCB SP 6 to 32 Amps, 10 KA breaking capacity, 240 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make for Item No. 81 to 83: Legrand/Siemens/Schindler/L&T

S&F Exhaust Fan heavy duty made of sturdy engineering plasic AC Single Phase 230/240 Volts of size 250mm Sweep with louvers including taking down existing exhaust fan complete all as directed. MAKE: Crompton Greaves/Havells/Bajaj/Usha/Orient

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6.3 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI medium grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC 1:3:6 type C-1 , 50 mm thick pre cast RCC 1 : 2 : 4 type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar, 15 mm GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I including taking out existing earth plate etc., complete all as specified and as directed by Engineer-in-Charge. NOTE: Rate quoted shall be deemed to include for earth lead and protection pipe upto 7.5m.

Taking down existing water heater (Geyser) of 25 litres capacity and keeping in safe custody and refixing complete in all respect including grouting to wall with suitable size of nut, bolt and connecting with necessary electrical system and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down house service brackets, any type and removing the materials and making good disturbed surfaces of wall/floor etc.all as complete all as specified and directed by Engineer-in-charge.

Taking down Aluminium service cable complete complete all as specified and directed by Engineer-in-charge.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, laying of pipe, cable etc., or for shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10 sqm on plan and getting out in soft/loose soil all as specified and directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removing surplus excavated soil to a distance not exceeing 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.

Supply and spreading of dry river sand in trenches for cable protection and punned down complete all as directed by Engineer-in-Charge. Note:- Punned thickness only shall be measured for payment purpose.

Supply and laying kiln burnt bricks sub class B of size 250mm x 125mm x 75mm laid in trenches for cable covers complete all as specified and directed by Engineer-in-charge.

Supply and laying in trenches, fixed to wall or drawn through pipe etc., XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 core and connecting with necessary lugs including taking out existing cable complete all as specified and directed by Engineer-in-Charge. Note:- Excavation, earth work, brick protection, protection pipe and sand coushioning shall be measured and paid separately. Make of cable shall be CCI / Gloster / ICC / Unistar / NICCO / Asian (RPG) / Havells / Polycab/PRG/Universal/Plaza/Crystal cables/Terracom/ Rallison/Mescab/Jeypore/KEI

Material and labour for 40 mm dia bore GI tubing Light grade, laid under roads/ floor, or fixed to wall or along the pole with suitable size M.S.flat iron clamps, nuts, bolts and washers for cable protection including taking out existing GI pipe complete all as specified and directed by Egineer-in-Charge. Make: TATA/ZENITH/JINDAL

S&F gun-metal, globe or gate valves of with iron wheel head, screwed both ends for iron pipe of 20 mm dia bore and fixed including taking down existing unserviceable valve complete all as specified and directed by the Engineer-in-Charge. Make: LEADER/NETA/ANCHOR/NMC/ DURGA/ZOLOTO or equivalent ISI marked make as approved by GE.

Supply and fixing Rotational moulded polyethylene water storage tank cylindrical vertical double layered, 1000 ltrs capacity with closed top hoisted and fixed in position all as specified in SSR Part I including taking down existing water tank complete all as specified and directed by Engineer-in-Charge. Make: SINTEX/ INFRA/ GP/ ROTEX/ ORIPLAST/ ASHISH/ POLYCON or equivalent ISI marked make as approved by GE.

S&F Symet ball valve 20 mm with high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe and fixed min weight for 20 mm 210 gms, including taking down existing unserviceable ball valve complete all as specified and directed by Engineer-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) exceeding 10cm width and setting in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge. Make : Shankar Saw Mills/Sangam Prefeb Products or equivalnt as approved by GE.

M&L for rendering 10 mm thick on brick work or concrete surfaces in cement mortar 1:6 finished fair and even complete all as specified and directed by Engineer-in-Charge.

M&L for Plain cement concrete 1:4:8 mix type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete etc., all as specified and directed by Engineer-in-Charge.

M & L Plain cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in coping including necessary formwork, weathering, slightly rounded or chamfered andgles, finishing of exposed surfaces of concrete to even and smooth without using extra cement all as specified and directed by Engr-in-charge.

Sub Total of Schedule 'A'

Schedule of Credit (Minus) Rs. 78,018.00 B/F from Ser page No. 34 NOTE: Bidder shall insert credit amount as rate Rs. 78,018.00 in Green field under Col-M. If bidder does not insert the amount the same will be deducted from total amount of Schedule 'A' and accordingly total amount of tender will be considered in deciding the lowest tender.

Sub Total of Schedule of Credit

G K SUTHAR

MANOJ JINDAL

SANJAY SAW MILL

MS BRAHMA CONSTRUCTION

RAJU TAMANG

GEETA CONSTRUCTION