GE (N) P/TOKEN- 63 OF 2020-2021PROVISION OF CERTAIN LBW AND SPECIAL REPAIR WORKS IN THE AREA OF AGE B/R (CENTRAL) UNDER GE (NORTH) PUNE

Amount

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 m in depth for foundation, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in soft/ loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exc.1.5 m in depthfor foundation, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in hard/ dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick with soils complete all as specified and as directed.

Removing of excavated material (soil) to distance exceeding 1.50 Km and not exc. 5 Km and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Material and labour for PCC (1:5:10) type E-2 (using 40 mm graded broken stone aggregate) as in foundations, filling, sub base and mass concrete complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-1 (using 20 mm graded broken stone aggregate) as in coping, blocks etc. including use and waste of form work, surface finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in lintels upto 1.5m clear span, seismic and other similar bands, cills, plinth courses, roof kerbs or mud stops, parapets, coping, benching, coping, hold fast blocks, bed blocks/ bed plates, kerbs for interlocking tiles etc. including weathering, slightly rounded or chamfered angles and throating including necessary form work all as specified and as directed.

Material and labour for precast solid cement concrete block masonry exc.10cm width using solid blocks of PCC design mix grade C5 set in cement mortar (1:6) complete all as specified and directed.

Material and labour for precast solid cement concrete block masonry exc.10cm width using solid blocks of PCC set in cement mortar (1:6) (Except blocks) complete all as specified and directed. (Blocks from dismantling shall be reused)

Material and labour for providing 35mm thick precast cement concrete (1:2:4) type B-0 (using 12.5mm graded broken stone aggregate) (measured solid) as in louvers and jallies, including all mouldings, set in cement mortar (1:4) complete all as specified and as directed.

M&L Brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

All as per Srl item No. 11 above but except bricks

Material and labour for 2nd class hard wood timber fixed, in scantlings, wrought unframed complete all as specified and as directed.

Material and labour for 2nd class hard wood timber fixed, in scantlings, clean sawn framed work complete all as specified and as directed.

Material and labour for 2st class hard wood plain fillets, square, rectangular or triangular in section, bull-nosed, splayed, chamfered or rounded on one edge or face, wrought, secured with fevicol and nails or brads, sectional area exc 13 and not exc. 25Sq.cm complete all as specified and as directed.

M & L for 2nd class hard-wood clean sawn battens, cross sectional area exc. 5 Sqcm and not exc. 15 Sqcm, spaced at 30cm centres to centres fixed with nails complete all as specified and as directed. (NOTE : Measurements shall be taken overall including both battens and spaces. Deductions shall be made only for openings exceeding 0.4 sqm each).

Fixing only for 2nd class hard-wood clean sawn battens, any cross sectional area spaced at 30cm centres to centres fixed with nails complete all as specified and as directed. (NOTE : Measurements shall be taken overall including both battens and spaces. Deductions shall be made only for openings exceeding 0.4 sqm each).

Supply and fix for 2nd class hard wood boarding, 30mm thick, clean sawn with butt joints and fixed with nails in any situation in roof, ceilings, partitions, facia, barge, soffit, etc (except flooring and skirting) complete all as specified and as directed.

Material and labour for 10mm thick fibre cement board (non asbestos) and fixed with self drilling and tapping screws of CSK head and joints finished with jointing compound and fiber tape as per manufacturer's recommendation complete of approved arch pattern any size and shape for wall/ partition complete all as shown on drawing and as directed.Make : Shera wall V-Board (Visaka Industries Ltd)/ Everest/ Charminar/ Ramco.

Supplied and fixed in skirting for 10 mm thick 1st class hard wood (teak wood) boarding planed one side & edges tongued and grooved or rebated and fixed with screws all as specified and as directed by Engr-in-charge.

Material and labour for 1st class hardwood (teak wood), designer, solid straigtht chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints for door/ window or similar work cut round to and fixing in arches all as specified and as directed .

Supply and fix for 35mm thick 1st class HW (teak wood) framed, panelled designer shutters (any number of panels), with designer panels of 1st class HW (teak wood) raised and have bevelled or chamfered margins (for each side) supplied and fitted to chowkats complete all as specified and as directed.

Supply and fix for 35mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including 35mmx 6mm thick 2nd class hard wood plain cover fillets on all sides complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutters from frame) area not exc.1.5 sqm each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as directed

Taking down door shutter of any description, area exc. 2 sqm each and refixing in same opening after making necessary repair, easing and adjusting complete all as directed. (Note: New builders hardware used in repair shall be measured and paid for separately)

S & F 0.4mm thick PVC white flex sheet over frame on walls complete all as specified and as directed. (Frame work shall be measured and paid separately.)

Supply and fix for 150 mm long aluminium anodised, barrel tower bolts of extruded section, fixed with stainless steel screws (conforming to the sample kept in GE office) complete all as specified and as directed.

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, (conforming to the sample kept in GE office) complete all as specified and as directed.

Supply and fix for 100mm size mild steel butt hinges, heavy weight, cold rolled and fixed complete (conforming to the sample kept in GE office) all as specified and as directed.

Supply and fix for 100mm size butt hinges, extruded brass, type D-11 with stainless steel hinge pin, bright polished and fixed with screws complete all as specified and as directed .

Supply and fix for 450mm size brass handles, extruded, fabricated type, of 32 mm bore brass tube and decorative polished complete all as specified and as directed.(Make- Godrej or equivalent of make as per Appx 'A' as approved by GE.)

Supply and fix for 150mm size extruded aluminium alloy handles fabricated type anodised fixed with stainless steel screws complete all as specified and as directed.

Supply and fix for door dead lock of brass both side key complete all as specified and as directed.(Make- QUBA Cat No.Q213 )

Supply and fix for floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring, overall length of cover plate 150mm conforming to sample kept in GE office all as specified and as directed.

Supply and fix, floor door stopper of brass body and tongue with hard drawn steel spring, overall length of cover plate 150mm complete all as specified and as directed.

Supply and fix in repair for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed

S & F Mild steel work for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and as directed

S & F Mild steel work for sliding channels including embeding in concrete and screwing etc. including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and as directed

Supply and fix for mild steel framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars, 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. or securing with clips complete all as specified and as directed.

Supply and fix for rolled mild steel section Fe 410-W(Gde-E-250) quality A as in main and cross beams, hip and jack rafters, purlins connected to common rafters and running rails and guides for sliding doors, column posts, wind ties, fixed with angle cleats or other connecting plates, drilled for fixing all as specified and directed.

Material and labour for rolled mild steel Fe 410-W(Gde-E-250) quality-A in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

Supply and fix for mild steel work in tubular trusses, main columns, posts, for structural work including special shaped washer etc. complete using hollow mild steel sections of square or rectangular tubes conforming to IS: 4923-1997 grade St.-240 fixed with angle cleats or other connecting plates complete all as specified and as directed.

Supply and fix for galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. in aprons, barriers, gates and similar works etc (each line wire to be measured) complete all as specified and as directed

Taking down old Sliding channels of aluminium / Iron and removing from site complete all as specified and as directed..

M & L for aluminium anodised sliding channel for fixing wooden sliding board and aluminium framing of square hollow pipe complete all as specified and as directed.

M&L for 5mm thick aluminium composite panel fixed to framework etc. complete all as specified and directed. (Frame work shall be measured and paid separately).

Material and labour for 0.80mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 120gm/ Sqm complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete all as specified and as directed.

Material and labour for Roof tiles Mangalore pattern interlocking at side joints, laid dry complete all as specified and as directed.

M&L for Roof tiles (Except tiles) Mangalore pattern interlocking at side joints, laid dry complete all as specified and as directed. (Note : Serviceable tiles obtained from dismantled shall be re-used.)

Material and labour for ridge or hip tiles to suit Manglore pattern of roofing tiles, bedded and jointed in cement mortar (1:6) etc including dismantling of tiles complete all as specified and as directed.

Material and labour for 0.90mm thick decorative laminate type 1 of surface finish, colour, pattern and size as approved, fixed with approved adhesive as per manufacturer’s instructions on horizontal and vertical surfaces etc. complete all as specified and as directed.

Material and labour for 18mm thick plywood, grade BWR, type BB, number of ply 9 Nos, fixed with fevicol and nails for working table/ storage almirah, cabinets, cupboards, racks and wall panelling, to the size and pattern as directed including fixing on walls, floors etc. complete all as specified directed.

Material and labour for 12mm thick plywood, grade BWP, type BB, number of ply 7 Nos, fixed with fevicol and nails for working table/ storage almirah, wall panelling to the size and pattern including fixing on walls, floors etc. complete all as shown on drawing and as specified and as directed.

Material and labour for 4mm thick one side decorative group match veneer plywood of design as approved by GE complete all as specified and as directed.

Material and labour for false ceiling with Single layer of size 1800mm x 1200mm x 12.5mm thick, tapered edge gypsum board (Gypboard) Plain (conforming to IS 2095-Part 1:2011, Certified board) is then screw fixed to ceiling section with 25mm drywall screws {Material-Carbon steel EN-ISO 7049/50, Finish-Case hardened Grey Phosphating} at 230mm centres on ceiling section & 150mm at periphery of ceiling. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc Pro-Fill Jointing compound (Conforms to ASTM C475), Gyproc Joint Paper tape fixed on and including metal grid of hot dipped galvanized steel sections and suspended as per manufacturer's specifications and instructions complete all as specified and as directed. Make: Gyproc-Saint Gobain or equivalent of Armstrong, Diaken, New Age (ACE) as approved by GE.

Material and labour for 12mm to 12.5mm thick mineral fibre board false ceiling on and including GI powder coated grid work of size 600 mm x 600 mm with using 32.5mm x 23.5mm x 1.5 mm thick main tee, 25 mm x 23.5 mm x 1.28 mm cross tee and 25mm x 23.5mm x 1.2mm angle fixed to wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling, suspended @ 120 cm C/C both ways, size of grid shall be 605 mm x 605 mm complete all as specified and as directed. Make :- Armstrong, Diaken, New Age (ACE). Note: Height of ceiling is above 5 metres.

Material and labour 50mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in plinth protection finishing the surface even and smooth without using extra cement including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled up with bitumastic complete all as specified and as directed.

M&L for double charged dark shade vitrified ceremic tiles 10 mm thick wooden texture size 200mm X 1200 mm, plank type laid over and including screed bed of 15 mm thick cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement to match dark shade complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

Material and labour for rendering 15mm thick in CM (1:6) on fair faces of brickwork or concrete surfaces wall finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM (1:6) on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing of walls, finished even and smooth without using extra cement complete all as specified and as directed.

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed

Material and labour for preparation of old treated plastered or unplastered surfaces of walls and applying one coat of cement base paint complete all as specified and as directed

Material and labour for complete removal of existing finish/treatment on wall surfaces, preparing surface and make surface free from loose particles, oil stains etc and applying two coats of cement based paint complete all as specified and as directed.

Supply and fix for 12mm thick toughened glass with etching as in openable door/ bathing cubical/ partitions including chamfered edge polishing fixed with necessary Ozone path touch fittings and fixtures etc. as per manufacturer's instructions complete all as specified and as directed.

S&F 08mm thick toughned glass with bevelled edge including digital printing of logo complete all as specified and directed

Material and labour for preparation of new untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old surfaces of wood and wood based material surface of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of wall and applying two coats of plastic emulsion paint complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of ceiling and applying two coats of plastic emulsion paint complete all as specified and as directed.

Material and labour for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new wooden surfaces of wall/ window/ railing/ floors/ wall panelling/ door/ staircase surface etc, application of resin pigment and hardener to desired colour and pattern and applying two coats of melamine polish with spray guns, compressor etc complete till glossy surface is obtained complete all as specified and as directed.

Removing steel almirah (methodox) 2.1m height and floor area n exc 7 sqm including its sliding channel and refixing the same in different location complete all as specified and directed.

Demolition of brick work/ precast concrete block walling/ boulder masonary, built in cement mortar or cement lime mortar including all quoins, pillars etc. complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as directed.

Dismantling timber scantlings, unframed work, 40 sq. cm and over in section, in any position complete all as directed.

Dismantling wooden boarding/ plywood of any description and any thickness including fillets fixed in any position with nails complete all as directed.

Dismantling battens for tiles, shingles etc. of any size including tiling fillets spaced exceeding 15cm complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

Dismantling structural steel work including doors, gates including framed truss etc. complete all as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness sheets including Nainital or similar pattern roof coverings/ galvalume/ aluminium sheeting complete all as directed.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings complete all as directed.

Dismantling single layer Mangalore pattern or similar tiles in roofing without disturbing existing false ceiling complete all as directed.

Dismantling of wall/ceiling board/POP ceiling of any description and any thickness including cover fillets/ grid etc complete all as directed.

Taking down carefully unserviceable point wiring of any description/ type/ size of light/ fan / tube/ power / two way/ bell etc. on TW batten/ conduit/casing caping including removal of batten/ conduit/ casing caping/ gutties/ wooden boards/ switches/ sockets/ regulators/ holders/ ceiling roses/ call bells/ light fittings etc. for taking credit and making good the disturbed surfaces of wall/ ceiling so as to match with the existing finishes complete all as directed. Note: Taking down of seviceable fittings and fixtures shall be measured and paid separatey.

Taking down the existing unserviceable main switch/ cut out/ MCB DBs/ sheet metal enclosure of any type/ capacity/ description as existing at site including MCBs any type/ capacity and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Taking down the unserviceable submain wiring of any type/ description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as directed.

Taking down the existing servicable LED 2'x2' squared LED panel safely and refix the same after completion of wiring work all as specified and directed.

Material and labour for point wiring using approved colour coding as per IS, with multistranded FRLS copper conductor 1.5 Sq. mm (nominal area), two single core PVC insulated and unsheathed multistranded flexible bright annealed cable 1100 volts grade ISI-694 marked through and including heavy grade, ivory/ white colour, ISI marked, 20 mm dia or higher dia. rigid PVC concealed conduit of including all accessories after chasing in wall/ ceiling etc, with concealed terminal sunken boxes factory made 16 SWG thick pressed steel of suitable size as per site requirement, covered with modular white cover plate with inner frame suitable for housing modular switches, sockets, regulators etc. including PVC insulated multistranded FRLS copper conductor 1.5 Sqmm (nominal area) single core flexible cable as earth continuity conductor and connecting to metal bodies of luminaires/ fans etc. for one light point controlled by one, one way switch 5/6 Amps complete all as specified and as directed.

All as per serial item No. 96 here-in-before but point wiring for one exhaust fan/ wall fan point controlled by one, one way switch 5/6 Amps and regulator.

All as per serial item No. 96 here-in-before but point wiring for one 3 pin 5/6 Amps socket outlet controlled by one switch on same board.

All as per serial item No. 96 here-in-before but point wiring for one 3 pin 5/6 Amps socket outlet controlled by one switch on independent board.

All as per serial item No. 96 here-in-before but point wiring for one bell point controlled by one bell switch 5 Amps.

All as per serial item No. 96 here-in-before but with FRLS copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded cable 1100 Volt grade ISI-694 marked including PVC insulated multistranded FRLSH copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor for 3 pin 15/16 Amps socket outlet on independent board.

Supply and fix for lamp holder, PVC body/ polycarbonate type with back plate, brass terminals suitable for batten/ slanting fittings complete all as specified and as directed.

Supply and fix for modular switch, one way 5/6 Amps, 1 module complete all as specified and as directed.

Supply and fix for modular switch, one way, 15/16 Amprs, 1 module complete all as specified and as directed.

Supply and fix for modular bell push, 6Amps, 1 module complete all as specified and as directed.

Suply and fix for bell electric ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

Supply and fix for modular socket outlet multi purpose 2 & 3 pin 5/6 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular socket outlet multipurpose, 3 pin 5/6 Amps and 3 pin 15/16 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular step type electronic fan regulator flush type 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

Supply and fix for modular step type fan regulator 120 watt 1 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

Supply and fix for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and as directed.

Supply and fix for sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall, connecting complete all as specified and as directed.

Supply and fix for sheet metal enclosure DB TPN, double door vertical type 4 way 415 volts, 50Hz suitable for MCCB incommer and SP/ TP MCBs as out going double door with magnetic locking systen, pre-wired including 200 Amps bus bar etc. suitable for operation on 415 volts 50Hz AC supply including necessary provision for inserting the DB in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and as directed.

Supply and fix for MCB SPN rated capacity 40 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB SP rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for ceiling rose, 3 terminals, PVC/ polycarbonate type, isolated body complete all as specified and as directed.

Supply and fix for highly efficient LED bulbs 10W with lumens out put not less than 1000 lumens, used as ready replacement for existing GLS/ CFL direct fit lamp in B-22 cap of make Havells/ Philips/ Wipro/ Bajaj/ HPL as approved complete all as specified and as directed.

Supply and fix for LED 10 watts batten aluminium extruded with decorative end caps all as per Cat No. BCLSB 10 NW/ WH of make Bajaj, Wipro Cat No. LL20-111-XXX-65-NE or its equivallent model in Havells, Philips as approved complete all as specified and as directed.

Supply and fix for LED down light recess mounted luminaire, round type 15 watts with efficiency of 100 lumens per watt, sleek design aluminium housing polycarbonate diffuser white finish operating voltage 150-270 volts AC, 50 Hz as per Cat No.BZSLO 15W NW of make Bajaj/ Philips Cat Part No DN172B LED9S-6500 PSU of or its equavalent in Wipro complete all as specified and as directed.

Supply and fix for wall mounted LED 20watts with lumens out put not less than 2000 lumens, box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired all as per Cat No. BCLAB 20W of make Bajaj, Cat No. LL20-281-XXX065-ALI of Wipro or equvalent of make Philips/ Havells/ Syska/ Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 20watts complete all as specified and as directed.

S & F for recess mounted 2' x 2' square LED panel 36 watts, 596 x 596 x 9mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed.

Supply and fix for recessed mounted low depth LED luminaire 2'x2' square LED panel 36 watts 596x596x9mm size sleek design aluminium housing, polycarbonate diffuser white powder coated finish operating voltage 140-270 volts, AC, 50 Hz all as per Cat No.BARSQL 36W NW of make Bajaj or equivalent of make Philips/ Wipro/Jaquar/ Crompton as approved complete all as specified and as directed.

Supply and fix for energy saving new generation environmental friendly long life versatile pressure die aluminium IP-66 for security light fitting luminaire of capacity 15 watt with high power LEDs as light source and electronic driver with lumens out put not less than 1500 lumens, with prewired all as per Cat No. BCLST 15 W LED I of make Bajaj or equvalent of make Philips/ Wipro/ Havells/ Crompton as approved, necessary mounting arrangements and provision of 2.5 Sqmm 3 core copper conductor cable multistranded from ceiling rose to light fitting including 40mm dia 1.5 metres long GI pipe medium grade bracket of suitable shape with clamps made out of MS flat iron of size 40mm x 6mm, nuts, bolts including taking down old existing unsesrviceable tube light fitting complete all as specified and as directed.

S&F ceiling fan (after assembling the same) with fan hook/box, 1200mm sweep BEE 5 star rated, 3 blade ISI marked, white colour, 240 volt AC 50 HZ single phase with hanging rod, conopy set, clamps, bolts nuts and connecting with three core flexible PVC copper conductor cable of size 0.50 sqmm from ceiling rose to fan complete all as specified and directed. Make: Havells Cat No. ES-50 or Bajaj cat No. Kessals 50 ISI of equivalent of Usha, Orient Electric kiara shine, Crompton.

Supply and fixing of exhaust fan plastic body of 200mm sweep, AC single phase, 240V heavy duty including louvers and connecting with three core flexible PVC copper conductor cable of size 1.50 sqmm from ceiling rose to fan including taking down old exhaust fan and depositing to store yard of AGE E/M North Pune complete all as specified and directed. Maqke: Bajaj Cat Part No. Maxma DX 8" or equivalent of Cromptoon, Havells

Material and labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less then 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel and connected to main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways with one handle for lifting made out of 8mm dia MS bar, funnel, wire mesh, 20 mm bore galvanized steel tubing (medium grade) for watering, filling charcoal or coke and salt in alternate layers, 15mm bore galvanized steel tubing light grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No.3 of SSR Part-I including taking out existing earthing . (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in quoted rate)

Material and labour for sub main wiring with approved colour coding as per IS with two runs of single core PVC insulated FRLSH cable with multistranded copper conductor of size 4.0 Sq. mm nominal area and drawing through and including non metallic rigid heavy duty PVC conduit and conduit accessories concealed in wall including one run of single core PVC insulated 4.0 Sqmm (nominal area) multistranded FRLSH copper conductor as earth wire connected from DB to DB/ main board complete all as specified and as directed. (Note- Two runs of 4.0 Sqmm, one run of 4.0 Sqmm conductor and one run of PVC conduit will be measured as one unit)

Material and labour for sub main wiring with approved colour coding as per IS with two runs of single core PVC insulated FRLS cable with multistranded copper conductor of size 4.0 Sq. mm nominal area and drawing through and including non metallic rigid PVC casing capping and accessories including one run of single core PVC insulated 4.0 Sqmm (nominal area) multistranded FRLS copper conductor as earth wire connected from DB to DB/ main board complete all as specified and as directed. (Note- Two runs of 4.0 Sqmm, one run of 4.0 Sqmm conductor and one run of PVC conduit will be measured as one unit)

Material and labour for sub main wiring with approved colour coding as per IS with four runs of single core PVC insulated FRLS cable with multistranded copper conductor of size 6.0 Sq. mm nominal area and drawing through and including non metallic rigid heavy duty PVC conduit white/ ivory and conduit accessories concealed in wall including two run of single core PVC insulated 6.0 Sqmm (nominal area) multistranded FRLS copper conductor as earth wire connected from DB to DB/ main board complete all as specified and as directed. (Note- Four runs of 6.0 Sqmm, two run of 6.0 Sqmm conductor and one run of PVC conduit will be measured as one unit)

Supply ,assembly and erection of GI sheet with TDF flange rectangular/square duct made out of 'L' shaped hollow profile, duly factory boxed, incl all accessories such as Corner, Cleat, Carriage bolt, Gasket and appropriate sealant on longitudinal joints etc complete of size 18 Gauge to extend existing duct including all opening and fixing material used for existing duct to extend all as specified and as directed. Note : 1.The quated rate is inclusive of neccssaaaary suction and deliver grills as required. 2. The design of duct grills layout will be planned by contractor and neccassary approval from accepting officer shall be obtainned. 3. The contractor is responsible for provide the designed air flow and disigned temporature. Necessary site visit will be arranged to the contractor before to Quote if required)

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

THE SAIRAM CONSTRUCTIONS