ADDITION / ALTERATION TO BDLG NO P-13 AT NCC COMPLEX AND CERTAIN OTHER SANCTIONED WORKS AT DIBRUGARH UNDER GE DINJAN NO 2

Dismantling of Plain corrugated Steel Sheeting, any gauge, thickness, including Nainital or similar type roof covering, complete in all respect as specified and directed.

Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed.

Dismantalling of cement concrete (unreinforced) in ground floors and pavings not exceedings 15 cm thickness (below or above ground level), complete in all respect as specified and directed.

Dismantalling of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete in all respect as specified and directed.

Taking down shutter exc 1 sqm and n. exc 2 sqm each, complete in all respect as specified and directed.

Taking down chowkats and shutters (without taking off shutters from the frame) n.exc 1.5 sqm each, complete in all respect as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4 sqm each, complete in all respect as specified and directed.

Taking down cement plaster of any thickness and description on brick/ concrete/ stone wall/ ceilings, etc, including raking out joints, hacking for key, scrubbing down with water etc, complete in all respect as specified and directed.

Demolition and breaking up drain pipes 75 mm/110 mm bore dia (Salt glazed ware, PVC or Reinforced concrete) set in cement mortar, complete in all respect as specified and directed.

M&L for brick work with sub-class "B" old size bricks of class designation (CD) 75, straight or curved on plan exc 6m mean radius, built in cement mortar (CM) 1:6, including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed.

M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed.

S&F rolled section as in framing for door/ vent/ CB chowkhats and the like fixed with angle cleat and connecting plates etc. using FE-410W (Grade E-250 quality "A") (Butt hinges shall be measured and paid for separately), complete in all respect as specified and directed.

S & F for Factory made single extruded WPC (wood polymer composite) solid door/ window / ceosetory windows & other frames / chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibers (wood power / rice husk /wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having maximum frame density of 750 kg / cum, screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum comprssive strength of 58 N / mm², Modules of elasticity 900 N / mm² and resistance to spread of flame of class A category with property of beeing termite / borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast / lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast / lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door / window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F for Factory made single extruded WPC (wood polymer composite) solid door/ window / ceosetory windows & other frames / chowkhat of size 65x150 mm comprising of virgin PVC polymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibers (wood power / rice husk /wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having maximum frame density of 750 kg / cum, screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum comprssive strength of 58 N / mm², Modules of elasticity 900 N / mm² and resistance to spread of flame of class A category with property of beeing termite / borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast / lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast / lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door / window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and laying for cement concrete in coping, hold fasts using type B-1, 1:2:4 (using 20 mm nominal size crushed and graded stone aggregate) or of similar type of work including necessary formwork complete in all respect as specified and directed.

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material, complete in all respect as specified and directed.

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws with bitumen washer to truss members of any material, complete in all respect as specified and directed (The measurement shall be carried out as in a plain sheet).

S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheet having tensile strenght of 550 Mpa as in eves covering or of similar type, fixed with self tapping screws with bitumen washer over mild steel flats, angles etc. and screws for fixing with framed structure complete in all respect as specified and directed. (Note:- MS work shall be measured and paid separately).

S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600 x 600 mm comprising of wall/ cleat angle of size 25x25x0.35 mm and corss tee of size 24x38x0.70 mm with 4 mm dia GI wire as suspender and including 4 mm thick decorative pre-painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/ wooden truss of any type including dismantling of existing false ceiling boards, complete in all respect as specified and directed. (Make:- Eternit, Everest or equivalent)

Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6, complete in all respect as specified and directed.

Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed.

M&L for any colour of granite stone without white spots Granite stone slab 17 to 19 mm thick, as in floor, dado, steps, laid over and including screed bed 15 mm thick in cement mortar (CM) 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cuttingl rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge, complete in all respect as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab flooring of size not less than 500 x 500 mm over 15 mm thick cement mortar (CM) 1:6 screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab of size not less than 500 x 500 mm in riser of steps, skirting, dado and pillar over 15 mm thick rendering in cement mortar (CM) 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed.

Taking down of existing roof treatment from roof and terrance, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specification:- (a)Applying cement slurry over concrete surfaces @3kg/sqm. (b)Rendring 15mm thick in cement mortar (1:4) mixed with water proffing compound as per manufactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). (c) Applying evenly one coat of cold bituminous primer conforming to [email protected] liter per square metre on the cleaned plastered surfaces (d) Applying evernly one coat of blown hot bitumen of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (e) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforces) with polyster non woven fabric wighing not less than 160 gms per square metre by torch application. The overlap shall be not less than 100mm on transverese direction and 75mm on longitudinal direction and sealing overlsaps. (f) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane.

M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:4), finished even & smooth without using extra cement, complete in all respect as speicifed and directed.

M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:6), finished even and smooth without using extra cement, complete in all respect as spefied and directed.

M&L 10 mm thick plastering on brick/ stone/ concrete surfaces of ceiling in cement mortar (1:3) finished even and smooth without using extra cement, complete in all respect as specified and directed.

Supply only water proofing compound complete, in all respect as specified and directed.

S & F CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall of size 20mm outer dia complete all as specified and directed.

S & F CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall of size 25mm outer dia complete all as specified and directed.

S&F in repair 20 mm bore of Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed, complete in all respect as specified and directed.

Providing and fixing in position kitchen cup board box type as per design and directed of 550-600mm deep, fixed over wall with PVC gittie and screws/or in beneath of kitchen counter, cup board, kitchen cabinet in required sizes as per site made out of 17-18mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 17-18mm thick PVC sheet. Provision of shelves, shutters, back side, top, bottom, side, made out of 17-18mm thick one side decorative laminated PVC sheet , all required brackets, screws etc,. The panel shall be fabricated using adhesives and screws whereever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per maufactures specifications and drawing including 15mmX20mm medium grade chrome finish two nos per leaf, slip on cabinet hinge/self-closing hinge, soft close hydraulic 4 hole cabinet auto cup hinge full overlay O crank with soft closing of make Godrej/Avis L Bihari/Hettich/Harrison and 50mm SS handle size all items each per shutter including taking down of existing box complete in all respect as specified and directed. Make: Rajshri Plastiwood, Sintex or of appd make. (Note: For payment, measurement shall be taken as front portion of cup board measurement only, rest other items/materials as specified shall not be measured or paid as these are included in this item)

Providing and fixing in position kitchen cup board box type as per design and directed of 250-300mm deep, fixed over wall with PVC gittie and screws/or in beneath of kitchen counter, cup board, kitchen cabinet in required sizes as per site made out of 17-18mm thick one side decorative lamination and other side balancing lamination sheet consisting of carcass 17-18mm thick PVC sheet. Provision of shelves, shutters, back side, top, bottom, side, made out of 17-18mm thick one side decorative laminated PVC sheet , all required brackets, screws etc,. The panel shall be fabricated using adhesives and screws whereever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per maufactures specifications and drawing including 15mmX20mm medium grade chrome finish two nos per leaf, slip on cabinet hinge/self-closing hinge, soft close hydraulic 4 hole cabinet auto cup hinge full overlay O crank with soft closing of make Godrej/Avis L Bihari/Hettich/Harrison and 50mm SS handle size all items each per shutter including taking down of existing box complete in all respect as specified and directed. Make: Rajshri Plastiwood, Sintex or of appd make. (Note: For payment, measurement shall be taken as front portion of cup board measurement only, rest other items/materials as specified shall not be measured or paid as these are included in this item)

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of appd size and shapeincluding fixing with aluminium "U" shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of appd make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No) grade), powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mm including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller 2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S&F 75 mm size of butt hinges stainless steel, complete in all respect as specified and directed.

S&F 100 mm size of mild steel butt hinges ISI marked, complete in all respect as specified and directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fiber glass from all sides.M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F 35mm thick second class HW glazed and skeleton shutters, open rebated and prepared to receive glass gauge etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc.; sizes of members of shuttrs as specified in SSR Part-I, section 8, clause 8.24 (a), complete in all respect as specified and directed.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 sqm in each pane, complete in all respect as specified and directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane, complete in all respect as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples fixing withbeads, complete in all respect as specified and directed.

S & F for Mild Steel, plain, black sheet1.25 mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughts; ducts; urinal troughts and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/riveted seams including bending turning up, mitred angles, stopped ends, outlets, etc. as required, complete in all respect specified and directed.

S&F 25 mm thick Flush shutters, solid core construction, with block board core with decorative face veneers withlipping on both sides, complete in all respect as specified and directed.

S&F 35mm thick Flush shutters, solid core construction, with block board core with decorative face veneers with lipping on both sides, complete in all respect as specified and directed.

S & F 18-19mm block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including necessary leaping/edge margin of 3mm thick complete in all respect as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section 200 mm long, complete in all respect as specified and directed.

S&F Aluminium handle cast type anodised 125 mm, complete in all respect as specified and directed.

S&F aluminium anodised sliding door bolts with hasp and staple (boilt type) 16 mm dia bolt, 250 mm long, with and including a minium of 6 bolts and nuts four on bolt plate and two on staple plate, complete in all respect as specified and directed

S&F mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

S&F PVC coloured insulated over MS pipe 20 mm dia curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed.

S&F plate rack made out of stainless steel sheet 0.50 mm thick overall size 900 mm (W) x 760 mm (H) x 250 mm (D) with three shelf, complete in all respect as specified and directed

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to drarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, complete in all respect as specified and directed. Make : Jayna, Neelkhanth, Nirali

S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed. Make:- Sheetal (Virat), Sintex, Oriplast, Supreme

S&F PTMT ball valve high pressure 20 mm bore with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe, complete in all respect as specified and directed.

S & F in repair 15mm bore concealed long neck , CP finished stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete in all respect as specified and directed.

S&F in repair vitreous chinaware sqatting pan of size 580 x 440 mm, 'ORISSA PATTERN' with new PVC 'P' or 'S' trap bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete in all respect as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level dual flush cistern 10 ltr capacity, white, wtih inlet, ball valve, float and handle including brackets & flush pipe of polyethylene for low or high level cistern of required height of high density PVC, 32 mm dia pipe, complete in all respect as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm, complete in all respect as specified and directed.

S&F in repairs 15 mm bore fancy type CP finished angle valves, cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete in all respect as specified and directed.

S&F in repairs long body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F in repair for 15 mm bore pipe brass chromium plated (CP) shower rose 125 mm size, fixed to iron pipe, complete all as specified and directed.

S&F Tubular towel rail, 20 mm dia, D type, 60 cm long between flanges cast copper alloy, chromium plated finish, complete in all respect as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and directed.

S&F in repair wash hand basins (WHB), vitreous china of size 550x400 mm (flat back or angle back type) with pedastal stand, including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32 mm dia bore waste fittings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15 mm bore dia fancy type CP finish pillar tap, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed.

S&F 75 mm dia of outlet, PVC (SWR) nahani trap, plain with SS grating of size 150mmX150mm, 0.75mm thick openable at center including jointing with solvent cement, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore including necessary MS pipe clamp, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore including necessary MS pipe clamp, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 110 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 75 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) single (single 'T') equal or unequal 110mm bore pipe with access door, complete in all respect as specified and directed.

S&F PVC (SWR) single (single 'T') equal or unequal 75mm bore pipe with access door, complete in all respect as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia bore, complete in all respect as specified and directed.

S&F PVC (SWR) vent cowl 75 mm dia bore, complete in all respect as specified and directed.

Supply and fixed unplasticised PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 160mm outside diameter as per IS:13592-1992 including dismantling and breaking up existing drain pipes and fixing necessary mild steel pipe clamps complete in all respect as specified and directed. Make: Supreme Type A, Prince, Oriplast.

Supply and fixed unplasticised PVC (SWR) bends any radius for160mm outside diameter of pipe as per IS:14735-1999 complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

Supply and fixed unplasticised PVC (SWR) junction single, (single Tee) equal or unequal for160mm outside diameter of pipe as per IS:14735-1999 complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

Supply and fixed unplasticised PVC (SWR) Gully trap 125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast.

M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, complete in all respcet as specified and directed.

Providing and laying reinforced concrete slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like using 1:2:4 type B-1, (using 20 mm crushed and graded stone aggregate) complete in all respcet as specified and directed.

M & L for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all not exceeding 20cm wide complete in all respcet as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete in all respcet as specified and directed.

S&F 10 mm dia and over TMT bar cut to length bent to shape required including cracking bending spiarlly for hoping for columns, hooking ends and binding with and including Mild Steel wire (annealed) not less than 0.90 mm dia or securing with clip, complete in all respect as specified and directed.

M&L for plinth protection or in foot path of 75 mm thick of cement concrete using type C-1, 1:3:6 (using 20 mm nominal size crushed and graded stone aggregate) in alternate penals and finished fair and even complete in all respect as specified and directed.

Complete removal of existing treatment on wall/ roof projections incl facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust loose paint etc by skilled labour complete all as specified and as directed

Complete removal of existing treatment on ceiling/ roof projections incl facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust loose paint etc by skilled labour complete all as specified and as directed

M & L for two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additive and color stay Techonology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/litre as per the LEEDS specifieecations, Anti Algal properties in two coats @ 1.79 ltr (Undiluted)/10 Sqm with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow spreed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface in both coats of paint complete all as specified and directed. Note : (a) The work pertaining to periodical services and water proofing shall be executed as per manufacturer instructions i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by Engr-in-Charge. (b) Cost of Scafolding upto 10 mtr height of building is included in this item.

M & L for waterproof cement based putty @ 1 Kg (undiluted) per sq mtr of average thickness 1mm over the newly plastered surfaces of wall to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanicsm) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface free from dust etc by skilled labour as per following steps : - Step 1 : Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 Kg putty per minute. Step 2 : Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a max pressure 3300 PSI Step 3 : Allow 6-8 hrs time to dry the putty surface Note : (a) The work pertaining to periodical services and water proofing shall be executed as per manufacturer instructions i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by Engr-in-Charge. (b) Cost of Scafolding upto 10 mtr height of building is included in this item. (c) Masking of waindow/doors during spray painting using polythine film will be included (d) Cleaning and clearing site of paint, mats etc included.

M & L for waterproof cement based putty @ 1 Kg (undiluted) per sq mtr of average thickness 1mm over the newly plastered surfaces of ceiling to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanicsm) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface free from dust etc by skilled labour as per following steps : - Step 1 : Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 Kg putty per minute. Step 2 : Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a max pressure 3300 PSI Step 3 : Allow 6-8 hrs time to dry the putty surface Note : (a) The work pertaining to periodical services and water proofing shall be executed as per manufacturer instructions i.e. Paint, Distemper, Putty etc is proposed to be used by the contractor and approved by Engr-in-Charge. (b) Cost of Scafolding upto 10 mtr height of building is included in this item. (c) Masking of waindow/doors during spray painting using polythine film will be included (d) Cleaning and clearing site of paint, mats etc included.

M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of alkali resistant primer including necessary preparation of surface, complete in all respect as specified and directed.

M&L for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers), wall care putty, complete in all respect as specified and directed.

M&L for preparation of newly undecorated plastered surface of Ceiling and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers), wall care putty, complete in all respect as specified and directed.

M&L for preparation of new undecorated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete in all respect as specified and directed.

M&L for preparing of old decorated wooden surface, of any description, not otherwise described, over 10 cm width or girth, and applying two coats of synthetic enamel paint, complete in all respect as specified and directed.

M&L for preparation of old decorated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint, complete in all respect as specified and directed.

Surface Excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified and directed.

Removing excavated material exc. 50 m and depositing where directed.

M&L for PCC (1:4:8) type D2 (using 40mm crushed and graded stone aggregate) as in foundaion and mass filling complete in all respect as specified and directed.

M & L PCC (1:3:6) type C-1 using 20 mm nominal size crushed and graded stone aggregate in coping, hold fasts or of similar items including necessary cutting, form work etc.complete in all respect as specified and directed.

S & F for 55-60mm thick coloured, glazed pre coated interlocking or without interlocking paver block of any shape and size confirming to IS 15658/1237 with upto date amendments, M-35 Grade with grey cement with pigment laid over fine river bed sand complete in all respect as specified and directed.(Note:- River bed sand shall be measured and paid separately). Sample as approved by GE.

M&L for river bed fine sand filling under floor or below paver blocks incl. watering and consolidation complete in all respect as specified and directed.

Supply, installation, testing & commissioning of glass top Deep freezer Single Phase of storage capacity 205/220 Ltrs, Five Star convertible type with temperature control facility, electric driven (single phase), 230 volts, AC, 50 Hz complete all as specified and directed

Supply, installation, testing & commissioning of glass top Deep freezer Single Phase of storage capacity 320 Ltrs Five Star convertible type with temperature control facility, electric driven (single phase), 230 volts, AC, 50 Hz complete all as specified and directed

S&F voltage stabilizer suitable for Refrigerator/deep freezer 300 to 600 Ltr capacity automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130-290 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 Amps complete all as specified and directed

Material and labour for providing point wiring for controlled by one switch with using 2.50 sq.mm (nominal area), stranded copper conductor, single core PVC insulated flame retardant unsheathed cable (Maintaining Colour Code) 1100 volts grade with and including PVC casing and capping (size of casing caping as required at site but not less than 20mm) of suitable size including PVC accessories / fittings and fixtures fixed on surface with using new PVC board or sunken type pressed steel box of adequate size, terminal boxes for mounting fittings/junction boxes with and including all accessories and using 2.50 sq.mm (nominal area), stranded copper conductor, single core PVC insulated flame retardant unsheathed cable green in colour as in earth continuity conductor connected to common earth dolly and connecting upto fittings complete all as specified and directed. NOTE: The quoted rates shall be inclusive for fixing casing caping to surface with using PVC raw plugs and provision of PVC boards/terminal/junction boxes of any shape and size. (a) One 5 pin 2 in 1 multi socket outlet 5amp/15 Amp on independent board .

Supply & fix switch socket combination, 5 in 1, multipurpose 5/15 Amps flush type universal ..

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, man holes etc. and getting out in soft/loose soil complete in all respect as specified and directed.

M & L for 150mm bore pipe for concrete bed in PCC 1:4:8 type D 2 using 40mm nominal size crushed and graded stone aggregate to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested in complete in all respect as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring jointslaying in trenches 150 mm bore complete in all respect as specified and directed.

M&L for cement concrete Type C-2, 1:3:6 (using 40mm nominal size crushed and graded stone aggregate) in foundations filling and mass concrete as in manhole etc. complete in all respect as specified and directed.

M & L for full Brick work with Cement bonded brick sub class B, class designation 75 old size bricks, straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete in all respect as specified and directed.

M&L for PCC 1:2:4 type B 1 (using 20mm nominal size crushed and graded stone aggregate) as in surface channels & drains complete in all respect as specified and directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc. .complete in all respect as specified and directed.

M&L 15mm thick rendering on brick work or concrete wall surfaces in cement mortar 1:4, finished even & smooth without using extra cement complete in all respect as specified and directed.

Supply only Integral waterproofing compound complete in all respect as specified and directed.

M & L PCC (1:2:4) type B-1 using 20 mm nominal size crushed and graded stone aggregate in coping, hold fasts or of similar items including necessary cutting, form work etc.cement complete in all respect as specified and directed.

M & L pre cast RCC (1:2:4) type B-1 using 20 mm nominal size crushed and graded stone aggregate in cover slabs or of similar items including necessary cutting, form work etc.cement complete in all respect as specified and directed.

M&L mild steel deformed TMT bar 10mm dia and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete in all respect as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete in all respect as specified and directed.

Removing excavated material n. exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete in all respect as specified and directed.

M&L for brick Septic tank for designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC Type A-1 1:1.5:3 Mix Baffle walls and Roof Slab including beams etc with Vent shaft,manhole openings with cover connection etc for 100 users capacity all as per Drawing available with sub division complete all as specified and directed.

M&L Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in Type A-1 1:1.5:3 cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.6m dia and 2.5m depth complete all as specified and directed.

Taking down aluminium point wiring for light, fan, bell socket, power socket etc complete including fittings and fixtures removing from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engineer-in-Charge.

Taking down ceiling fan of any type and size and keep in safe custody for refixing after completion of work complete all as specified and as directed by Engineer-in-charge.

Taking down old submain wiring of any type/ core including earth wire including batten/ PVC conduit/ casing caping and making good the disturbed surface to match with the existing complete all as specifid and as directed.

Taking down old MCB DB of any type and size and making good the disturbed surface to match with existing complete all as specified and as directed.

Taking down old MCB (SP/SPN) of any type and size complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS, PVC insulated and unsheathed stranded cable drawn through and including non metallic, heavy duty PVC concealed conduit not less than 20mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI flush boxes / sunken boxes made out of 1.2mm thick of any module from 2 to 18 module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly including modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over sunken box for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan / bell point contorlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLS copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and as directed by Engineer-in-Charge. NOTES : - (i) The quoted rates shall be deemed to be inclusive for cutting chases by chase cutter in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary accessories/fittings. (ii) Point wiring & earth wire shall be connected to each & every flush/sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

One Light point/ Fan point/ Exhaust fan point controlled by one, one way switch complete all as specified and directed.

One Socket outlet 3 Pin, 5 Amp on same board complete, all as specified and directed.

One bell point controlled by one, one way switch complete, all as specified and directed.

All as per item No 136 above but one Socket Outlet Point, 5 Amp on independent board with 2.5 Sqmm cable complete all as specified and as directed by Engineer-in-charge.

All as per item No 136 above but one Socket Outlet Point,15 Amp on independent board with 2.5 Sqmm cable all as specified and as directed by Engineer-in-charge.

Supply & fix modular switch 1 way 6A, 1 module complete all as specified and as directed.

Supply & fix modular switch 1 way 16A, 1 module complete all as specified and as directed.

Supply & fix modular bell push one way 6 amps 1 module complete all as specified and as directed.

Supply & fix modular socket 6A-2/3 pin combined 2 module complete all as specified and as directed.

Supply & fix modular socket 6/16A-2/3 pin combined 2 module complete all as specified and as directed.

Supply & fix modular fan regulator step type 2 module complete all as specified and as directed.

M & L for ceiling rose, surface Bakelite of three terminals PVC/Polycarbonate,isolated body (ISI Marked) complete all as specified and as directed by Engineer-in-charge.

Supply & fix Call bell multi music type AC 230 volts, single pole (ISI Marked) & connection complete all as specified and as directed.

Supply and fixing of LED light fitting 1x20W, 220V, AC, batten type with driver , holder including 20W LED tube light for connecting up with three core flexiable copper conductor cable of suitablae size from celing rose to connector of any description and in any position complete all as specified and directed by Engineer-in-charge.

Supply and fixing of integrated LED batten 9/10 watt, 2 feet long tube light fitting with high efficient diffuser mirror light, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of the light/fitting of any description and in any position complete all as specified and directed by Engineer-in-charge.

Supply and fixing of LED security light luminaire 30/35 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP66 protection, better optics for uniform distribution with multiplte LEDs having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down old unserviceable security light fitting of any description and in any position complete all as specified and directed.

M&L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying, including filling cavities with filler, one coat after cleaning all dust etc including servicing and minor repair complete all as specified and as directed.

Fixing only ceiling fan (taking down against item No 02 above) of any type including provision of flexible copper cable of suitable size from ceiling fan to ceiling rose complete all as specified and as directed.

Supply and fixing of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engineer-in-charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed by Engineer-in-charge.

Supply and fixing of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing electric water heater (Geyser) storage type 25 Ltr capacity vertical mounting type, BEE 5 Star rated, 230V, 50 Hz, 2000 watt with suitable size fastner including provision and connecting up suitable size and length of SS braided pipe with adaptor for inlet and outlet water connection. Geyser of metal body water proof and rust proof, water resistnace & splash proof (IPX4). inner tank superior glass line enamel coating single weld line,heavy duty magnesium anode rod, Corrosion resistance, PUF insulation for radient heat loss and energy saving. Temprature gauge and adjustable knob for temperature setting, auto cut off, capillary thermostat, multiple safety system for protection against dry heating, over heating and over pressure, rated water pressure 8 bar, whirl flow technology, anti rust copper element, safety valve, NRV incl all fixing accessories all as specified and as directed. Note : (i) Minimum 2 year warrenty on product (ii) Minimum 3 year warrenty on heating elemnt (iii) Minimum 7 year warrenty on inner tank

Supply, installation, testing of SPN distibution board 8 way,double door , IP 43, as per IS 8623 including minimum IP 43 degree of protection with built in fully insulated copper bus bar, not less than 100 Amps capacity insulated neutral bar and earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles/glands complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed by Engineer-in-charge.

Supply and fixing of MCB 25 to 32 Amp SP&N, 240 volts 10 KA 'C' series with all incoming/outgoing connections with proper size lugs complete all as specified and directed.

Supply and fixing of MCB 6 to 32 Amp SP, 240 voltss 10 KA 'C' series with all incoming/outgoing connection with proper size lugs complete all as specified and directed.

Supply and fixing of single pole and neutral enclosure with a two pin and earth plug and socket complete with one number single pole MCB 20 Amps , 240 Volts complete all as specified and as directed.

M & L for providing sub main wiring with two single core 6.00 Sqmm (nominal area) PVC Insulated FRLSH unsheathed multi stranded copper conductor cable 1100 volts grade drawing through including concealed PVC Conduit of suitable size including 6.00 Sqmm PVC insulated unsheathed multi stranded FRLSH single core copper conductor cable for earth wire complete all as specified and directed by Engineer-in-charge. Note : (i) Three runs of single core 6.00 Sqmm multi stranded copper cable and one run of conduit shall be measured as one run length (ii) cutting chasing and making good to the disturbed srface shall be included in quoted rates.

All as per Ser item No 30 above but with 4.00 sqmm copper cable (nominal area)

M & L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion, complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Supply and fixing of sheet metal enclosures vertical distribution board VTPN, (MCCB DB) 4 ways, double door, 415 volts with 200 amps rated bus bar IP 43 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole thermal release type, 100 Amps, 16 KA as incomer and MCBs as out going complete with making suitable size of MS cabinet as per IS dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs/thimbles/glands and making good the disturbed surface matching with existing surface complete all as specified and directed by Engineer-in-charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep and getting out in any type soil for laying pipes etc, complete all as directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, complete all as directed by Engineer-in-Charge.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as directed by Engineer-in-Charge.

Supply and spreading fine river sand in trenches for cushioning of under ground cable/filling cable ducts complete all as specified and as directed by Engr-in-Charge at site. Note : - Only punned thickness shall be measured for payment purpose

Supply and laying burnt brick sub class ‘B’ of standard size laid in trenches as protection to cables complete all as specified and as directed by Engineer-in-charge.

M & L for boring of holes under road, pavement, hard standing by trenchless technology technique for 40-80 mm dia pipe complete all as specified and as directed by Engineer-in-charge.

M & L for light grade galvanized pipe ISI marked laid in trenches, under road or fixing on wall/pole/ crossing nallah etc for cable protection of bore 40 mm complete all as specified and as directed by Engineer-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power UG cables (heavy duty) 1100 Volts grade with stranded aluminium conductor confirming to relevant IS specifcations of size 25 sqmm 3.5 core including taking down existing cable of any size complete all as specified and as directed by Engineer-in-charge.

Cutting existing steel tubing for alteration or addition (each cut measured ) bore of pipe 40 mm / 50 mm /80mm, complete all as specified and directed.

Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector), complete all as specified and directed.

Supply and fix GI pipe 20 mm dia bore, medium grade with all fittings such as Sockets, Reducers, Unions, Tees, Nipples, Bends etc laid in trenches/walls/floors complete all as specified and directed by Engineer-in-Charge.

All as per serial item No. 1666 here-in-before but of size 25mm bore but including taking down existing, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 168 here-in-before but of size 40mm bore but including taking down existing, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of Gun Metal gate valve with iron wheel head, suitable for 25 mm bore pipes, screwed both ends for iron pipe or for union including taking down old existing valve of any type, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 169 here-in-before but of size 40mm bore.