NER-LJN Division:- Upgradation (Modernization) of infrastructure facilities of New coaching depot at GKP.

A-CPWD-DSR-2021 Items

Item Breakup - A-CPWD-DSR-2021 Items

slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 11.28S SAND STONE FLOORING 11.31 Extra for pre finished nosing in treads of steps Metre 5 157.35 786.75 46 of Kota stone/ sand stone slab. 11.37S CERAMIC GLAZED TILES LUCKNOW-NER-DIVISION-ENGINEERING/NORTH EASTERN RLY 11.39 Providing and laying rectified Glazed Ceramic Sqm 18 1142.8 20570.4 floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, 47 Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41S VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid 11.41 on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 48 11.41.2 Size of Tile 600x600 mm Sqm 118.98 1416.65 168553.02 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 11.56 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 11.56.1 Polished Granite stone slab colour of Black, Sqm 13.53 3908.8 52886.06 49 Cherry/Ruby Red or equivalent 12.0 ROOFING Providing, fixing and embedding sand cast iron accessories for rain water pipes in the 12.40 masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately): Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring 12.41 conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 50 12.41.1 75 mm diameter Metre 20 213 4260 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes 12.42 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.5 Bend 87.5 degrees 51 12.42.5.1 75 mm bend Each 6 91.8 550.8 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of 12.43 required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 52 12.43.1 75 mm Each 6 310.85 1865.1 LUCKNOW-NER-DIVISION-ENGINEERING/NORTH EASTERN RLY 12.50 Providing and fixing precoated galvanised iron Sqm 650 671.55 436507.5 profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 53 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 13.0 FINISHING 13.1S CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 54 13.1.2 1:6 (1 cement: 6 fine sand) Sqm 973.15 282 274428.3 15 mm cement plaster on the rough side of 13.2 single or half brick wall of mix : 55 13.2.1 1:4 (1 cement: 4 fine sand) Sqm 18.12 339.7 6155.36 13.4S CEMENT PLASTER (IN COARSE SAND) 13.4 12 mm cement plaster of mix : 56 13.4.1 1:4 (1 cement: 4 coarse sand) Sqm 766.41 307.25 235479.47 CEMENT PLASTER WITH A FLOATING COAT OF 13.7S NEAT CEMENT Cement plaster 1:3 (1 cement: 3 coarse sand) 13.9 finished with a floating coat of neat cement. 57 13.9.1 12 mm cement plaster Sqm 350 386.55 135292.5 Distempering with oil bound washable 13.41 distemper of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and Sqm 796.44 162.55 129461.32 58 including water thinnable priming coat with cement primer Applying one coat of water thinnable cement 13.43 primer of approved brand and manufacture on wall surface : 59 13.43.1 Water thinnable cement primer Sqm 796.44 64.45 51330.56 Painting with synthetic enamel paint of 13.61 approved brand and manufacture to give an even shade : 60 13.61.1 Two or more coats on new work Sqm 1080 131.45 141966 Painting with synthetic enamel paint of 13.62 approved brand and manufacture of required colour to give an even shade : 13.62.1 Two or more coats on new work over an under Sqm 50 191.4 9570 61 coat of suitable shade with ordinary paint of approved brand and manufacture Painting with aluminium paint of approved 13.63 brand and manufacture to give an even shade . 62 13.63.1 Two or more coats on new work Sqm 750 121.45 91087.5 Applying priming coats with primer of 13.85 approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. Painting with aluminium paint of approved 13.100 brand and manufacture to give an even shade: 63 13.100.1 One or more coats on old work Sqm 6550 79.4 520070 LUCKNOW-NER-DIVISION-ENGINEERING/NORTH EASTERN RLY Finishing walls with water proofing cement 13.109 paint of required shade : 13.109.2 Old work (one or more coats @ 2.20 kg/10 Sqm 5550 63.25 351037.5 64 sqm) complete. 15.0 DISMANTLING AND DEMOLISHING Demolishing cement concrete manually/ by mechanical means including disposal of 15.2 material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c cum 10 2007.1 20071 65 equivalent design mix) Demolishing brick work manually/ by mechanical means including stacking of 15.7 serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 66 15.7.4 In cement mortar cum 22 1698.45 37365.9 Dismantling roofing including ridges, hips, 15.28 valleys and gutters etc., and stacking the material within 50 metres lead of: 67 15.28.1 G.S. Sheet Sqm 900 136 122400 Dismantling manually/ by mechanical means including stacking of serviceable material and 15.43 disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge : 68 15.43.2 bituminous road Sqm 450 353.65 159142.5 15.60 Disposal of building rubbish / malba / similar cum 110 219.35 24128.5 unserviceable, dismantled or waste materials by mechanical means, including loading, 69 transporting, unloading to approved municipal dumping ground or as approved by Engineer- in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 16.0 ROAD WORK 16.49S MISCELLANEOUS 16.75 Providing and laying C.C. pavement of mix M- cum 876.5 8277.55 7255272.58 25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush 70 etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 17.0 SANITARY INSTALLATIONS Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with 17.1 manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan Each 2 5781.35 11562.7 71 of size 580x440 mm with integral type foot rests LUCKNOW-NER-DIVISION-ENGINEERING/NORTH EASTERN RLY Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush 17.2 pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic Each 2 5540.55 11081.1 72 seat and lid Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing 17.4 cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.4.1 One urinal basin with 5 litre white P.V.C. Each 2 5268.85 10537.7 73 automatic flushing cistern Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm 17.7 C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.3 White Vitreous China Wash basin size 550x400 Each 3 2040.85 6122.55 74 mm with a pair of 15 mm C.P. brass pillar taps Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, 17.10 including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.1 Kitchen sink with drain board 75 17.10.1.1 510x1040 mm bowl depth 250 mm Each 2 6008.45 12016.9 Providing and fixing P.V.C. waste pipe for sink 17.28 or wash basin including P.V.C. waste fittings complete. 17.28.1 Semi rigid pipe 76 17.28.1.1 32 mm dia Each 8 90.95 727.6 17.31 Providing and fixing 600x450 mm beveled Each 2 1411.15 2822.3 edge mirror of superior glass (of approved 77 quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 17.34 Providing and fixing toilet paper holder : 78 17.34.1 C.P. brass Each 6 680.8 4084.8 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing 18.7 the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.-Internal work - Exposed on wall 79 18.7.1 15 mm nominal dia Pipes Metre 50 255.9 12795 80 18.7.2 20 mm nominal dia Pipes Metre 20 325.1 6502 81 18.7.3 25 mm nominal dia Pipes Metre 10 408.55 4085.5 18.15S BRASS FITTINGS LUCKNOW-NER-DIVISION-ENGINEERING/NORTH EASTERN RLY Providing and fixing brass bib cock of 18.15 approved quality : 82 18.15.1 15 mm nominal bore Each 6 303.85 1823.1 83 18.15.2 20 mm nominal bore Each 6 327.95 1967.7 Providing and fixing ball valve (brass) of 18.18 approved quality, High or low pressure, with plastic floats complete : 84 18.18.2 20 mm nominal bore Each 4 397.45 1589.8 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c 18.32 necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 18.32.1 With common burnt clay F.P.S.(non modular) Each 4 1712.15 6848.6 85 bricks of class designation 7.5 18.48 Providing and placing on terrace (at all floor Litre 2000 9.7 19400 levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking 86 arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Providing and fixing PTMT grating of approved 18.58 quality and colour. 18.58.1 Circular type 87 18.58.1.2 125 mm nominal dia with 25 mm waste hole Each 5 45.25 226.25 21.0 ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket 21.1 etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.3 Polyester powder coated aluminium (minimum Kg 35 474.7 16614.5 88 thickness of polyester powder coating 50 micron) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings 21.1.2 wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) LUCKNOW-NER-DIVISION-ENGINEERING/NORTH EASTERN RLY 21.1.2.3 Polyester powder coated aluminium (minimum Kg 40 573.4 22936 89 thickness of polyester powder coating 50 micron) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. 21.3 complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.2 With float glass panes of 5 mm thickness Sqm 8 1325.55 10604.4 90 (weight not less than 12.50 kg/sqm) 21.17 Providing and fixing anodised aluminium grill Kg 50 560.85 28042.5 (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 91 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). 22.0 WATER PROOFING 22.14 Grading roof for water proofing treatment with 92 22.14.3 Cement mortar 1:4 (1cement : 4 coarse sand) cum 4.18 13378.15 55920.67 Total 21284703.23