SPECIAL REPAIR TO BLDG NO P-203/01 TO 12 OF FIELD HOSPITAL AT OLD AIR FIRLD, SRINAGAR UNDER GE 970 EWS

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exceeding 1.50 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.50 sqm n.exc 4 sqm each complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description (used in framework for stageing of water tank) of any description not otherwise provided for complete all as specified and directed by the Engr-in-Charge.

Dismantling timber scantlings 40 sq. cm over in section in any position for framed work complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where directed complete all as specified and directed by the Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by the Engr-in-Charge.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by the Engr-in-Charge.

Dismantling floor,hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles to stores and rubbish off the premises,complete all as specified or directed by the Engr-In-Charge.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc.complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-Charge.

Taking up or down steel tubing and connections 32mm bore complete all as specified and directed by Engr-in-charge

Taking up or down CI Pipes (Incl all fittings) with spigot and socket ends and lead joints incl burning out joints and removing lead of 100/75 mm di pipe complete all as specified and directed

M&L for 75mm thick, PCC, (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection , finishing cement concrete surface even and smooth without using extra cement including joints filling with sealing compound Grade 'A' complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick, PCC, (1:4:8), type D-2 (using 40 mm graded crushed stone aggregates) as in sub base of flooring without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick, PCC, (1:2:4), type B-1 (using 12.50 mm graded agg as in floors surfaces finishied even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15mm thick screed in CM (1:4) complete all as specified and directed by Engr-in-Charge.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15mm thick screed in CM (1:4) complete all as specified and directed by Engr-in-Charge.

M &L for 16-18mm thick machine cut kota stone slab flooring of size not less than 550x550mm set and jointed in neat cement slurry and pointed in coloured epoxy grout to match including rubbing and polishing laid over and including 20mm thick screed bed in CM 1:4 including roughening surfaces of existing concrete floor by picking, sweeping clean & washing down with water to remove dust and apply neat cement slurry @ 3.00kg of cement per sqm, etc complete all as specified and directed.

All as per item No 19 above but on skirting laid over and including 10mm thick backing coat in CM 1:3 complete all as specififed and directed

M&L for 16-18mm thick Machine cut kota stone slab as in riser of brick steps, staircase, skirting, dado and pillar includng rubbing and polishing and jointed with grey cement slurry mixed with pigment to match the shade of the slab with and including backing coat in 10mm thick rendering in CM (1:3) to receive Kota Stone complete all as specified and directed by Engr-in-Charge.

M & L for Glazed ceramic coloured tiles 450x350x7mm thick, on vertical surface such as skirting, dados and risers to step etc set and jointed in neat cement slurry and pointed in coloured cement to match to laid over and including 10mm thick backing coat in CM 1: 3 complete all as specified and directed by Engr-in-Charge.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills, cooking platforms and like in CM 1:4 including pointing in white cement 1:2 using marbal dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-Charge.

M&L for Rounding to edges of stone slab one edge, such as in steps, cooking plateform etc , and other similiar situations complete all as specified and directed by Engr-in-Charge.

S&F Factory Made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick wood grain printed PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet reinforced MS square tube supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, With Particle board Core, supply & fixing in frame at site as per specification and drawing of page No 146 of SSR Part II complete all as specified and directed by Engr-in-Charge.

Pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface, etc complete all as specified and directed.

All as per item No 27 above but size of frame 165x 60mm complete all as specififed and directed

S&F 2nd class hard wood 35 mm thick factory made glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing pain, champerred or rounded, fitted with cut and shutters as specified in SSR Part 1, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F 35mm thick flush shutter solid core construction with block bord core and plywood face panels commercil type both side complete all as specified and directed.

S&F Box type Steel window (Factory made ) outer frame made out ERW tube 'P' section 65mmx45mmx25mm and shutters of ERW tube 'P' section 50mmx35mmx20mm openable (double) shutter with glazed openable shutter on (External side) and wire huazed openable shutters on (Internal side) with steel pintal hinges, steel handle 100 mm long, mild steel tower bolt 02 Nos on each suhtter, stopper of 'Z' section and its locking arrangement at mild steel hook and eye including 0.6 mm dia nominal dia of stainless steel wire cloth avg width of aperture 1.40 mm dia and 4mm thick steel glass window and 4mm figured glass for ventilators all as specified and directed by Engr-in-Charge. Note : The quoted rate against the above item shall also include :- (i) For provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat tar on the ends of steel frame in contract with bricks/ concrete surface. (ii) 04 Nos MS Steel Lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs. (iv) 0.36mm dia SS wire mesh (v) 4mm thick sheet glass - for window.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge

S&F Second class hardwood (wrought) in scantling for timber frame and fixed complete all as specified and directed by Engr-in-Charge.

Refixing only of timber scantling obtained from dismantling complete all as specified and directed by Engr-in-Charge.

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described, and treated with Creosoting complete all as specified and directed by Engr-in-Charge.

Prelaminated particle board, 18/19mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, ISI marked fixed in panels with 6mm thick teak wood lipping complete all as specified and directed by Engr-in-Charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor Overall length of cover plate 140mm complete all as specified and directed by Engr-in-Charge.

S&F mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F 100mm size, Stainless Steel medium weight, butt hinges, with stainless screws complete all as specified and directed by Engr-in-Charge.

S&F 200mm size, aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, 250mm size complete all as specified and directed by Engr-in-Charge.

S&F 150mm extruded aluminium alloy anodised handles, fabricated type, complete all as specified and directed by Engr-In-Charge.

Hasp and staple aluminium anodized 100mm long including bolt to hinge plate and fixed with screws, etc complete all as specified and directed.

S&F in repair stainless steel curtain rod fancy type 25mm dia etc complete all as specified and directed by Engr-in-Charge.

S&F in repair 25mm dia Stainless steel fancy type brackets inclucing fixing arrangements complete all as specified and directed

S& F in repair 25mm dia Stainless steel fancy type finale caps etc. Complete all as specified and directed.

M&L for Preparation of new or previously untreated wooden surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthetic enamal paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

M & L for Framed work such as grills , gratings, etc, with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars , barred iron doors,ladders, framed balusters , walk ways , railings, frame work of water tanks and similar work ,conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

S&F Mild steel joist, channel, angle or tee sections fixed independantly without connecting plate etc confirming to Fe 410-W (Grade E-250) complete all as specified and directed by Engr-in-Charge.

PCC (1:2:4), type B-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete for fixing of angle iron work inlcuding necessary form work and allied work complete all as specified and directed by Engr-in-Charge

Preparation of new or previously untreated steel surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for RCC (1:2:4), type B-1 (using 20mm graded crushed stone aggregetes) as in slab supporting on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves including necessary forms works complete all as specified and directed by Engr-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for Precast RCC (1:2:4) ,type B-1 ( using 20 mm graded stone aggregate ) as in manhole and drain cover slab and similar articles with plain faces, set in cement mortar 1:4 , all as specified and directed by Engineer-in-Charge.

Filling of sunken floor with PCC 1:5:10 using 40mm graded crushed stone aggregate with integral water proofing compound including breaking and removal of existing filling of lime concrete/PCC/brick bats and rubbish out off the premises, etc complete all as specified and directed.

M&L for preparig surface of sunken slab and applying 15mm cement plaster 1:3 cement sand mortar with integral water proofing compount both on floor a & wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating Polymer modified cementation coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturers instructions both on floor as well as on wall and sunken floor shall be filled with graded cement concrete upto top level to receive top flooring complete all as specified and directed. Note :- PCC shall be measured and paid separately.

M&L for GI tubing as in spout pipe light grade 32mm bore including of required shape complete, all as specified and directed by Engr-in- Charge.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 metre mean radius in cement mortar 1:6 complete, all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plain to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick/concrete/stone wall surfaces for any description and finished even and fair without using extra cement complete all as specified or directed by the Engr-in-Charge.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick/concrete/stone wall surfaces for any description and finished even and fair without using extra cement complete all as specified or directed by the Engr-in-Charge.

M&L rendering 10mm thick in cement plaster 1:3 on ceiling surface finished even and smooth without using extra cement.

Preparation of newly plastered surfaces of wall and apply two coats of distemper oil emulsion (OBD) over a coat of cement wall primer (from same manufacturer of OBD) over a layer of wall care putty not less than 2mm thick etc complete all as specified and directed.

Preparation of existing distempered surfaces of walls by complete removal of existing treatment and apply two coats of distemper oil emulsion (OBD) over a coat of cement wall primer (from same manufacturer of OBD) over a layer of wall care putty not less than 2mm thick etc complete all as specified and directed.

Preparation of newly plastered surface of walls and applying two coats of cement based paint over a coat of white wash complete all as specified and directed by Engr-in-Charge.

Preparation of old plastered surface of walls and applying one coat of cement based paint over a coat of white wash complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new or previously untreated surface on Ceiling and applying three coats of white wash, complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of old decorated plastered or unplastered surface of ceiling and applying one coat of white wash, complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of old painted wooden surfaces exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

Anodized aluminum snap grid frame work for false ceiling, size of grid 605mmx605mm, runners of size 15x32mm with hangers of 6mm dia GI (up to 1200mm length) adjusting level, fixed to roof by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including 6mm thick non asbestos fibre cement building board of size 610x610x6mm inserted to GI/Aluminum frame work with screws, including taking down existing ceiling board & grid work etc of any type/pattern etc complete all as specified and directed. Note :- Invoice from company’s authorized dealer shall be submitted with material by the contractor along with dealership certificate. Certificate of genuineness from the manufacturer shall also be submitted by the contractor before getting the material passed from the department.

Pre-painted galvalume 0.5mm thick high strength corrugated sheeting with aluminium zinc coating of an ecofriendly colour coating not less than 25 micron having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as required, including dismantling plain or corrugated steel/AC sheeting, any gauge, thickness etc complete all as specified and directed.

Pre-painted galvalume 0.5mm thick high strength plain sheeting with aluminium zinc coating and 600mm width of an ecofriendly colour coating not less than 25 micron having tensile strength of 550 Mpa as in ridges, fixed with self tapping screws as required, including taking down existing ridge of any description etc complete all as specified and directed.

S&F in repair 1.25mm thick plain, black mild steel sheeting in stepped flashings (measured as the minimum rectangle from which the pieces can be cut) complete in squares not exceeding 0.50 sqm each panes complete all as specified and directed by Engr-In-Charge.

M&L for Cutting chases, pinning in, in brick walls, making good to facings where required and pointing in cement mortar1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engr-in-Charge.

GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Taking down existing surface/concealed water tubing 15mm bore and refixing in same/new location after cleaning and application of bituminous paint on concealed portion of tubing including cutting & threading pipe and provision of additional fittings such as socket, tee, elbow, union etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Lagging to pipes used in internal water supply or plumbing all round with 25mm thick bounded mineral wool preformed "SNAP ON" pipe sections of density 144 kg/Cum conforming to IS-9842 for 15mm dia GI pipe provided with chicken mesh wire netting 25mm gauge,20mm mesh with 0.01 mm aluminium foil complete all as specified and directed by Engr-In-Charge.

Lagging to pipes used in internal water supply or plumbing all round with 25mm thick bounded mineral wool preformed "SNAP ON" pipe sections of density 144 kg/Cum conforming to IS-9842 for 20mm dia GI pipe provided with chicken mesh wire netting 25mm gauge,20mm mesh with 0.01 mm aluminium foil complete all as specified and directed by Engr-In-Charge.

S&F in repair of Vitreous china wash hand basins counter top (Make : Jaquir Cat part No FLS-WHT-5601 or equivalent of Hindware/Parryware/Somany) of size 565mmx415mm white fixed to counter including 32mm bore PVC waste coupling 90 cm long etc inlet and outlet connection including dismantling existing wash basin and making good to disturbed floor, etc complete all as specified and directed.

Vitreous china White Squatting Orissa Pattern pan (Make : Somany Cat part No 121115 or equivalent of Hindware/Parryware) of size 580x440mm, including cast iron ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe, fixed in repair including dismantling existing squatting pan and making good to disturbed floor, etc complete all as specified and directed.

PVC flushing cistern 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore and PVC connection 15mm bore 450mm long fixed in repair including taking out existing high/low cistern, etc complete all as specified and directed.

Stainless steel sink with draining board 1mm thick sheet for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 405mm x 355mm x 178mm, including 32mm bore PVC waste pipe of minimum length 600mm , fixed in repairs including taking down existing unserviceable sink, etc complete all as specified and directed. Make : Blue star Cat part No BSSBSD-52 or equivalent of Nirali/Neelkanth

S&F in repair CP wall mixer with telephonic shower arrnagement and including hand shower, connecting legs and wall flange complete all as specified and directed by Engr-in-Charge. (Make : Jaquar Cat part No FLR-CHR-5217N or equivalent of Hindware/Marc)

S&F 15mm bore brass chromium plated centre hole basin mixture with regular spout without popup waste system with 450mm long braided hoses, 20mm cartridge size (Make : Jaquar Cat part No FLR-5167NB or equivalent of Hindware/Marc)

S&F in repair CP sink mixer with regulator swinging spout wall mounted with connecting legs and wall flenges complete all as specified and directed by Engr-in-Charge. Make: Jaquar Cat part No FLR-CHR-5309N or equivalent of Hindware/Marc.

15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule, fixed in repair etc complete all as specified and directed. Make : Jaquar Cat part No FLR-5047N or equivalent of Hindware/Marc.

Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes fixed in repairs etc complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent of Hindware/Marc.

15mm bore chromium plated angular stop cock with wall flange of cast copper alloy, fancy type, with capstan head, screwed both ends for iron pipe, fixed in repair etc complete all as specified and directed. Make : Jaquar Cat part No FLR-5053N or equivalent of Hindware/Marc.

20mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe, fixed in repair, etc complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 450mm long of appoved make fixed in repair etc complete all as specified and directed.

Single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat fixed in repair etc complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent of Hindware/Marc.

Glass shelf assembly 55cm long with brass chromium plated bracket guard and railing fixed with chromium plated screw and PVC cleat fixed in repair etc complete all as specified and directed. Make : Jaquar Cat part No AQN-7771 or equivalent of Hindware/Marc.

Stainless steel plate rack of approx size 750x900mm fixed with chromium plated screw and PVC cleat in repair etc complete all as specified and directed. Make : Blue star Cat part No KPR-315 or equivalent of Nirali/Diamond.

PVC (SWR) pipes single socketed (Fixed in repair) of 110mm bore with rubber ring joints laid in floor or trenches complete all as specified and directed by Engr-in-Charge (Make : Prince/ Supreme) .

All as per item No 97 abvoe but 75mm bore pipe complete all specified and directed

PVC (SWR) pipes single socketed (Fixed in repair) of 110mm bore with rubber ring joints fixed to wall complete all as specified and directed by Engr-in-Charge (Make : Prince/ Supreme) .

All as per item No 99 abvoe but 75mm bore pipe complete all specified and directed

S&F UPVC bends (any radius) of 110 mm dia.

S&F UPVC bends (any radius) of 75 mm dia.

PVC (SWR) branches pieces, Single(single Y), equal or unequal ( in repair) fitted with oval access door of 110 mm bore complete all as specified and directed by Engr-in-Charge.

All as per item No 103 abvoe but 75mm dia bore

S&F in repair UPVC traps 'P' or 'S' of 110 mm dia

S&F in repair UPVC cowls of 75mm dia

S&F in repair UPVC cowls of 110mm dia

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F in repair Grating doom 100 mm dia with waste hole of PTMT. (Minimum weight 25gms) complete all as specified and directed by Engr-in-Charge.

S&F in repair PTMT grating doom with or without waste hole 75mm dia (Min weight 25gms). Complete all as specified and directed.

S&F in repair single/ multi PVC (SWR) floor trap 75 mm dia, plain with grating including jointing to waste pipe with solvent etc complete all as specified and directed.

Rotational moulded polyethylene water storage tanks three layer of capacity 500 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball etc complete including taking out existing water tanks of any description all as specified & directed.

Taking down carefully unsv/damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc) and removing material from site and making good to the disturbed surface to match with existing finish etc complete all as specified and directed.

Point wiring using FR-LSH PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FR-LSH PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bend, junction box and pressed steel sunken box 60 mm deep & 1.6 mm thick duly painted inside and anticorrosive out side for mounting switches, sockets, fan regulators etc with 3mm thick plastic laminated sheet cover of suitable size, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point etc complete all as specified and directed. (Note : Switch/bell push/fan regulator etc shall be measured and paid separately)

All as per Srl item No. 114 above but for 5 Pin 5 Amp socket outlet point controlled by one switch 5 Amps one way on same board, etc complete all as specified and directed.

All as Srl item No. 114 above but for one bell point controlled by one push button on independent board complete all as specified and directed.

All as per Srl item No. 114 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FR-LSH PVC insulated multi-strand copper conductor wire including 1.5Sqmm FR-LSH PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes etc complete all as specified and directed.

Switch piano flush type, single pole, 6 Amp, one way, AC 230 volts etc complete, all as specified and directed. Make : Anchor (Penta) Cat Part No : 38014 or equivalent of Havells/SSK

Switch Bell push, flush type, 5 amp complete all as specified and directed by Engr-in-Charge.

Ceiling rose polycarbonate isolated body surface Bakelite, not less than 50x20mm, three terminals, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 39040 or equivalent of Havells/ SSK

Electronic fan regulator, stepped type, hum free socket type suitable to control speed of fan 0-100%, 230 V etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 38284 or equivalent of Havells/ SSK

Switch piano flush type, single pole, 16 Amp, one way, AC 230 volts etc complete, all as specified and directed. Make : Anchor (Penta) Cat Part No : 38477 or equivalent of Havells/ SSK

Socket outlet, 2 in 1, 5 pin, 6 Amp & 16 Amps, flush type, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 38397 or equivalent of Havells/ SSK

Socket outlet, 2 in 1, 5 pin, 6 Amp, flush type, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 38364 or equivalent of Havells/ SSK

Bell Multi Music type, single phase 240Volts, complete all as specified and directed by Engr-in-Charge.

Double door MCB DB SPN, 240 Volts, 08 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar including taking out old unsv MCB DB any size/type, etc complete all as specified and directed. Make: Legrand Cat Part No 6077-11 or equivalent of L&T/ABB/SCHNEIDER

Double door MCB DB TPN, 415 Volts, 04 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar, including taking out old unsv MCB DB any size/type, etc complete all as specified and directed. Make: Legrand Cat Part No 6079-13 or equivalent of L&T/ABB/SCHNEIDER

S & F in repairs MCCB 4 Pole 125 Amp, 50 KA breaking capacity with adjustable thermal setting and adjustable magnetic setting 430V, 50 Hz AC Supply including taking out old unsv MCB DB any size/type, etc complete all as specified and directed. Make: C & S Cat No CSC3H4* Cat Part No 6079-13 or equivalent of L&T/ABB/SCHNEIDER.

MCB single pole neutral (SPN) 240 volts, 40 to 63 Amps, 10KA (C-series) of approved make and cat part etc complete all as specified and directed.

MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) of approved make and cat part etc complete all as specified and directed.

Earthing in repair complete with galvanised steel earth plate electrode 600mm x 600 mm x 6mm buried directly in ground (earth pit not less that 2.25 metre deep below ground level) vertically, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to galvanised iron wire 4mm dia by means of nuts, bolts, washers of GI steel all as shown on electrical plate No 3 of MES schedule Part I connected to earthing test point and testing on completion with and including necessary excavation and earth work, earth electrode, earthing lead from electrode to equipment / substation, adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded black trap/granit/Basalt stone aggregate) for earth pit with 40 x 40 x6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm graded black trap/granite/Basalt stone aggregate) 40mm thick cover, reinforced with 6mm dia bars 3 Nos both way with 12mm dia round bar handle, GI light grade watering pipe 15 mm dia with funnel and wire mesh, and 15 mm dia GI light grade earth lead protection pipe, complete all as specified and directed by Engr-in-Charge.

Sub main wiring with FR PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FR PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring etc complete all as specified and directed. Note : Two run of cable for phase, neutral and one run of cable for earth including conduit will be measured and paid as one unit length.

S&F in repairs of LED battern with poly carbonate housing and integrated electronic drive 1x18 watts 4 feet light fitting with white acrylic cover along with LED lamp whit e colour compete including connecting up with twin core twisted flixible copper conductor cable with suitable size all as directed. Make : Bajaj Cat Part No BCLSB18NW or equivalent of Philips/Crompton/ Wipro Note : CA No shall be written on each fitting before installation.

Street/Security light LED , 45 Watt energy savings and environmental friendly long life versatile pressure die cast aluminium fittings including necessary brackets and clamps complete connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed by Engineer-in-Charge. Make : Bajaj Cat Part No ENXT P 45LWWCRPCSD or equivalent of Philips/Crompton/ Wipro Note : CA No shall be written on each fitting before installation.

Lamp holder(in replacement) insulated body with back plate suitable for batten fitting including LED lamp of capacity 9 watts complete all as specified and directed by Engr-in-Charge.

S&F in repairs single pole and neutal enclosure with a two pin and earth plug and socket comoplete with one singlew pole MCB 16 to 20 A fo rgeyser connection all as specified

1100 volt grade XLPE insulated heavy duty cable, 35 sqmm 3.5 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable etc complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 metre in depth for taking up or laying of cables including getting out in any kind of soil complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, and well ramming, in layers not exceeding 25 cm thick , complete all as specified and directed by Engr-in-Charge.

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Sand cushioning to underground cables 8cm thick before laying cable and 15cm thick after laying and streching the cable, complete all as specified and directed by Engr-in-Charge. Note :- For payment purpose punned thickness shall be measured.

Brick well burnt locally available sub class 'B' laid over sand cushioning to cable in trenches keeping width of brick parallel to the length of cable complete all as specified and directed by Engineer-in-Charge.

S&F LED Lamp suitable for pandent type holder 9 watts all as specified

M/S BASHIR AHMAD TANTARY

M/S maqsood enterprises

M/S B A Traders

FIRDOUS AHMAD BABA

M/S ABDUL HAMID RATHER

JK BUILDERS AND ENGINEERS

M/s Bashir Enterprises