Providing Borewell, RO Plant, Play Materials,Pergola, Sprinkler, Turf, Gym Equipments,Seating Arrangements,Handrails,Light Arrangements and additional infrastructure in Moongil Eri Park at Ward No.10 TCMC Zone No.01

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 350Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

Foundation

Ground Floor

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick work in CM 1:5 (one cement & five sand) using II class ground moulded bricks of size 9"X43/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification.

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with Vitrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Supplying & fixing door shutters for Mediun Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete.

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification.

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supply and fixing Flexible polyethelene irrigation pipe 16 mm dia / 2.5 / 1.1 - 1.4 mm CL - II. " Netafim " including installation charges.

Supply of Micro sprinkler of half & full circle with 55 LPH output flow with necessary micro tube & stake. Rain Bird / JISL make including installation charges.

Supply and fixing 16amps DP switch with metal clad(side handle) of 500 V with F & N on suitable teak wood Board of size 30cmx20cmx6 cm including necessary internal conection,earth connection etc.,complete (SD 145)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with neccessary arrangement using charcoat, common salt, G.I.reducer, checj nuts etc., and mansonry workand providing RCC cover slab 38mm thick for the Brick mansory including cost of steel and fabrication of reinforcement etc., complete in all respectes as directed by the departmental officers. (SD 211)

Supplying and run off 8 SWG copper wire on walls or below ground level with necessary 'U' nails, earth work excavation and refilling & including the cost of all materials etc., complete in all respects as directed by the departmental officers.(SD 75)

Supplying and fixing of 8 way three phase DB of 16amps/way with 16amps DP switch with metal glad of 500 volt(side handle) with Fuse and Neutral of suitable T.W. Board of size 40cm x30cmx6.3cm with earth connection etc., complete in all respects as directed by the departemental officers (SD 151)

Supplying and fixing of 5 A 3 pin and 2 pin combined flush type wall socket with 5A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet including cost of wall socket, switch and labour charges fo wall cutting, grouting, flushing and making good, painting with primary and finishing coat for MS box etc., complete as directed by the departmental officers. (SD 136)

Supplying and fixing of 5 A /15A 3 pin flush type wall socket with15A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet including cost of wall socket, switch and labour charges fo wall cutting, grouting, flushing and making good, painting with primary and finishing coat for MS box etc., complete as directed by the departmental officers. (SD 139)

Supplying and fixing MCB isolator 32A TP with earth connection (Legrand (MDS/Hager (L & T make)

Wiring with 2x1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark confirming to IS: 694/1990 in suitable PVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with PVC accessories in flush with wall including the cost of cable, pvc pipe and specials, ceiling rose, flush type 5ams SP mark switch, PVC junction box, 16gauge MS switch box 100mm x 100mm x 75mm covered by laminated hylem sheet 3mm thick, cement, labour and making good of concealed portion with suitable colour for concealed PVC LIGHT point. (SD 16)

Wiring with 2x1.5sqmm PVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark confirming to IS: 694/1990 in suitable PVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with PVC accessories in flush with wall including the cost of cable, pvc pipe and specials, ceiling rose, flush type 5ams SP mark switch, PVC junction box, 16gauge MS switch box 300mm x 200mm x 75mm covered by laminated hylem sheet 3mm thick, cement, labour and making good of concealed portion with suitable colour for concealed PVC FAN Point. (SD 16)

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire with painting of suitable colour (derived from SD 56)

Supplyand laying of 2 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (derived from SD 176)

Supplying and fixing of 1200 mm (48") AC ceiling fan complete with stepped electronic 300 W regulator with 1 m down rod with fan clamp, side plates and cross arm of size departmental officers. (SD 106)(18") etc., complete as directed by the departemental officers.

Supplying and fixing 12" (30cm dia) light duty Exhaust fan including cost of all materials,labour, lead, lift, etc complete (SD 114)

supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 441)

Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 -1/2 feet using angle iron of size1-1/2" x 1-1/2" x 1 /4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nut ssupports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1"x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with 1 No 63 Amp 30 MA Four Pole RCD/ RCCB (LowerEnd) with suitable necessary connection with earth connection completet. (SD 132)

Wiring with 2x4 sqmm(56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet for 15 A 3 pin non inter locking CS plug with continuous earth wire connection with 1.5 sqmm PVC unsheadthed Cu. cable and making good of the concealed portion, with suitable colour for concealed power plug point. (SD 313)

Providing following type of plants for park lawn area including finishing and labour charges cost and conveyance of all material at site etc., complete as per standard specification.

PURPLE ORCHID TREE

COPPER POD

GOLDEN SHOWER

NEEM TREE

INDIAN MAHAGONI

INDIAN CORK TREE

PUNGAM

INDIAN CORAL TREE

RED BOTTLE BRUSH

PRIDE OF INDIA

CRAPE MYRTHRLE

ROYAL PALM

FOX TAIL PALM

TERMINALIA

PLUMBAGO

SCREWPINE

BOUGAINVILLEA

WATER MELON

FICUS PANDA

GOLDEN THRYLIS

CROWN OF THORN

MOSE IN THE CRADDLE

HIBICUS MIX

LADY PALM

WHITE FRANGIPANI

SHELL GINGER

ZEBRA PLANT

RAIN LILLY

LANTANA PURPLE

Supplying and fixing of slide Senior to a length of 3.00 m with 80mm dia leaver and 40mm top bar with MS pipes.The seater is of moulded plastic. The ladder frme is made up of 25mm M.S. ppe., hanrail 20mm dia MS pipe and the centre support is 80mm dia MS pipes. The cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supplying and fixing of Double Swing of height 2.40m height with 40mm dia MS pipes support as legs and top bar is 50mm dia. The seat is 9mm thick reinforced rubber with Antiskid chequred top with heavy ball bearing and the suspension is 7mm dia electro galvanized chain and the cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and Fixing of Merry Go Round Four seater 40mm dia GI pipessupport as legs and top bar is 50mm dia. The seat is 9mm thick including cost of Materials and cost of all labour charges for fixing, testing and commissioning the same etc. complete as per specification.

Supplying and fixing of Four Seater SEESAW to a height of 0.50m with 80mm dia leaver and 40mm top bar with MS pipes. The seatr is of moulded plastic with heavy duty bush bearing. The cost shall inclusive of all materials, labours and fixing etc complete as directed by the dpeartmetal officers

Supply and Fixing of Single seater spring seesaw 40mm dia GI pipessupport as legs and top bar is 50mm dia. The seat is 9mm thick including cost of Materials and cost of all labour charges for fixing, testing and commissioning the same etc. complete as per specification.

Supply and Fixing of Single seater spring seesaw 50mm dia GI pipessupport as legs and top bar is 70mm dia. The seat is 9mm thick including cost of Materials and cost of all labour charges for fixing, testing and commissioning the same etc. complete as per specification.

Supplying and fixing of Jungle Gym for below 12 years old childrens to a height of 2.10m with 80mm dia leaver and 40mm top bar with M.S. Pipes. The ladder frame is made up of 25mm M.S.Pipe, hanrail 20mm dia M.S. Pipe and the centre support is 80mm dia M.S. Pipe The cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Air Rider Maximum User Weight 120 kilogram, Main Central Pipe 100mm dia G.I. Pipe Heavy, Handle Frame 32mm dia G.I. pipe, Seat Frame 32mm dia G.I. Pipe, 32mm dia G.I. Pipe, Connecting Links Pipe, Foot Rest Pipe 32mm dia G.I. Pipe, MS Foundation Plate Thickness 12 millimeter 750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X4mm Seat and Back Rest 2.5mm thick, M.S. Perforated with uniformbending radius to avoidsharp edges Bearings Tapered Roller Bearing inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Leg Press Cum Twister Single Maximum User Weight 110 kilogram for Main Frame 125mm dia G.I. Pipe, 40mm dia G.I. Pipe Leg Movement Frame Pipe, Handle Frame 25mm dia G.I. pipe, Tapered Roller Bearing Foot Rest Aluminum castingmaterial MS Foundation Plate Thickness 12 millimeter, Foundation Pipes 750mm deep GI Pipe, supported withM.S. Angle 25 X 25 X4mm inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Ellipitical Cross trainer for Maximum User Weight 100 kilogram, Main Central Pipe 100mm dia G.I. Pipe, Handle Frame 32mm dia G.I. pipe, Seat Frame 32mm dia G.I. Pipe, Connecting Links 25mm dia G.I. Pipe, Foot Rest Pipe 32mm dia G.I. Pipe, MS Foundation Plate Thickness 10mm Foundation Pipes with anchoring 500mm deep GI Pipe, Seat and Back Rest 2mm Thick G.I. Seat with uniform bending radius to avoid sharpedges inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Big Shoulder Wheel Maximum User Weight 100 kilogram, Main Central Pipe 80mm dia G.I. Pipe, Moving Frame Pipe 80mm dia G.I. Pipe, Foot Rest Frame/ Foot Rest Hinging Pipe 25mm dia G.I. Pipe, Connecting Links 25mm dia G.I. Pipe, MS Foundation Plate Thickness 10mm Foundation Pipes with anchoring 500mm deep GI Pipe, supported with M.S. Angle 25 X 25 X4mm, Seat and Back Rest 3mm thick, HDPE with uniform bending radius to avoid sharpedges inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Leg lift Post Maximum User Weight 120 kilogram, Main Central Pipe 100mm dia G.I. Pipe Heavy, Handle Frame 32mm dia G.I. pipe, Seat Frame 32mm dia G.I. Pipe, 32mm dia G.I. Pipe, Connecting Links Pipe, Foot Rest Pipe 32mm dia G.I. Pipe, MS Foundation Plate Thickness 12 millimeter 750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X4mm Seat and Back Rest 2.5mm thick, M.S. Perforated with uniformbending radius to avoidsharp edges Bearings Tapered Roller Bearing inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Pull Up Bar Single Maximum User Weight 110 kilogram for Main Frame 125mm dia G.I. Pipe, 40mm dia G.I. Pipe Leg Movement Frame Pipe, Handle Frame 25mm dia G.I. pipe, Tapered Roller Bearing Foot Rest Aluminum castingmaterial MS Foundation Plate Thickness 12 millimeter, Foundation Pipes 750mm deep GI Pipe, supported withM.S. Angle 25 X 25 X4mm inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Standing & Sitting Twister for Maximum User Weight 100 kilogram, Main Central Pipe 100mm dia G.I. Pipe, Handle Frame 32mm dia G.I. pipe, Seat Frame 32mm dia G.I. Pipe, Connecting Links 25mm dia G.I. Pipe, Foot Rest Pipe 32mm dia G.I. Pipe, MS Foundation Plate Thickness 10mm Foundation Pipes with anchoring 500mm deep GI Pipe, Seat and Back Rest 2mm Thick G.I. Seat with uniform bending radius to avoid sharpedges inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and fixing of Pull Up & Twister Maximum User Weight 100 kilogram, Main Central Pipe 80mm dia G.I. Pipe, Moving Frame Pipe 80mm dia G.I. Pipe, Foot Rest Frame/ Foot Rest Hinging Pipe 25mm dia G.I. Pipe, Connecting Links 25mm dia G.I. Pipe, MS Foundation Plate Thickness 10mm Foundation Pipes with anchoring 500mm deep GI Pipe, supported with M.S. Angle 25 X 25 X4mm, Seat and Back Rest 3mm thick, HDPE with uniform bending radius to avoid sharpedges inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers.

Supply and Delivery and Fixing of 50Lit Capacity Wall-mount cum Counter-top water purifier.2. Reverse Osmosis Technology.3. Anti-bacteria 3-in-1 Silver Doser, Taste Conditioner and Activated Carbon as post treatment of RO, to enhance the shelf life & taste of water.4. No of Stages: 6 (1+5). 5. Purification Capacity: Up to 25 lph† .6. Optional storage tank of capacity: 7 ltrs.7. Built-in SMPS to operate from 120~280 V AC for erratic voltage supply.8. Can Attach with Water Cooler or Dispenser.9. Dimensions: W 335 D 235 H455 Following Specification(1) Purification capacity-20*(+/- 5) Litres per hour *(2) Max Duty Cycle-150 liters per Day (3) Storage Tank Capacity- 7 Litres (optional at extra cost) (4) 6 stagesPurification -1) Sedement , 2)Activated Carbon 3)Sediment, , (4)RO Membrane,(5)Post Corbon, 6) TDS Minimiser,5) RO Membrane-2 Units (6) Minimum Inlet Water Pressure -0.3 kg/sq cm (7) Maximum Inlet water Pressure -2 kg/sq cm ( if input water pressure is more than 2kg/sq cm , install PRV before the Unit) (8) Input Voltage -160-300V AC ( 50Hz) (9) Operating Voltage -48V DC (10) Input water Temperature- Min 5 Celsius & Max 50 Celsius (11) Total Dissolved Solids (TDS)- Up to 2000 ppm(12) Total Hardness-500 ppm (max) (13) Rejection of TDS- Up to 95% (14) Recovery- Up to 25%(15) Dimensions (mm)- L 415 W 265 H 524 (16) Net Weight-12.5 kgs.(17) Power rating-48 W (* Purification output capacity tested on raw water with TDS level of 750 ppm at room temperature)

Supply and delivery of 240 Lit Capacity Mobile Garbage Bins shall conform to following specifications:-G• The material shall be heat and chemical resistant and shall be UV stabilized.The manufacturing process shall be Injection molding only as specified by EN 840-1 standard.The bins shall have suitable lid of HDPE Injection Molded at the top which shall be hinged on one side and open easily by gravity while unloading in refuse compactors.The bins shall have Nominal volume of 240 Ltrs.The bins shall have Two Solid rubber wheels of 200 mm Dia. (+-5 mm). Both these wheels shall be mounted on axle, which shall be corrosion resistant.The bins shall be provided with single piece pulling handle.The bins shall have deep and strong combs as per EN Standards. These combs shall ensure optimum accommodation on the lifting devices i.e. Refuse Compactors with Universal Bin Lifting mechanism.The useful load shall be min. 110 Kgs. As per EN standard.The color of the bins shall be Green/Blue/Grey/Yellow/Red and aesthetically pleasant in nature.

Supply and fixing of Concrete Statue of Inidan national Emblem including cost of all materials, lead,lift etc.,

Supply and fixing of Granite Chess Table including cost of all materials, lead,lift etc.,

Supply and fixing of Granite Circular Seating including cost of all materials, lead,lift etc.,

Supply and fixing of Granite Table Tennis including cost of all materials, lead,lift etc.,

Supply and fixing of Ornamental Garden 3 person Granite chairs including cost of all materials, lead,lift etc

Supply and fixing of Ornamental Garden 3 person Granite chairs including cost of all materials, lead,lift etc

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

I LOVE TAMBARAM LED Sign - Acrylic with GI metal leeters with GI base. Of thickness 3mm/4mm ; LED 1.5W

NAMMA TAMBARAM LED Sign - Acrylic with GI metal leeters with GI base. Of thickness 3mm/4mm ; LED 1.5W

SUN LOGO Sign - Acrylic with GI metal leeters with GI base. Of thickness 3mm/4mm ; LED 1.5W

HEART LOGO Sign - Acrylic with GI metal leeters with GI base. Of thickness 3mm/4mm ; LED 1.5W

Supply & Fixing of Tambaram TCMC Logo - 4 ft logo including cost of material, labour, lead, lift etc.,

Supply & Fixing of Tambaram TCMC Logo - 1.5 ft logo including cost of material, labour, lead, lift etc.,

Supply and fixing of LED Strip Light Supply and fixing of LED Strip Light including cost of material, labour, lead, lift etc.,

Supplying and fixing 8W bollard light with base plate including cost of material, labour, lead, lift etc., (SOR Vol 1 M -2705)

Supplying and fixing Garden Spike light 5W outdoor light including cost of material, labour, lead, lift etc.,

Supplying and fixing 4Way wall light 6W light including cost of material, labour, lead, lift etc.,

Supplying and fixing Post Lantern light 50W outdoor light including cost of material, labour, lead, lift etc.,

Supplying and fixing LED Flood Light 150W with Integrated Driver

Supply and Fixing of Name Board logo for Park as directed by the departmental officers etc., complete.

Supply and Fixing of Pylon Board logo for Park as directed by the departmental officers etc., complete.

Supply and Fixing of Secuirty cabin including material , labour , transport , etc as directed by the departmental officers etc., complete.

V MEENAL AND CO (BID ID -1468768)